Effect of Yttrium on Microstructure and Hot Corrosion Preformance of Laser Clad Co-Based Alloy

The structure of the yttrium modified Co-base alloy layers formed by laser cladding on 2Cr13 and 1Cr18Ni9Ti steel surfaces and its hot corrosion performance have been investigated systematically.The re- sults show that the Y-containing cobalt base clad alloy has a finer microstructure and higher corrosion re- sistance to the salt mixture of 75% Na_2SO_4+25%NaCl at high temperature.The unique properties are ob- tained with addition of 0.875% Y for the formation of a continuous and compact oxide scale.The compact scale may act as a barrier for the inward diffusion of oxygen and sulphur and also for the outward diffusion of alloying elements.

Microstructure and wear resistance of Fe-based and Co-based coating of AISI H13

Fe-based and Co-based cladding layers were prepared on the surface of AISI H13 hot die steel by laser cladding technology.The microstructure,hardness and abrasion resistance of the two cladding layers were studied by means of optical microscope,scanning electron microscope,rockwell hardness tester,and high temperature friction and wear tester.Also,the red hardness of the cladding layers was measured,after holding the layers at 600℃ for 1 hour by muffle furnace and repeated 4 times.The rockwell hardness values of the substrate,the Fe-based and the Co-based alloy coating measured were HRC 47,HRC 52 and HRC 48,respectively.The red hardness values of the substrate and the Fe-based cladding layer were decreased,while that of the Co-based cladding layer was increased.The Co-based cladding layer has the minimal wear loss weight and friction coefficient among them.The wear mechanisms of the substrate,the Fe-based layer and the Cobased layer attribute mainly to abrasive wear,adhesion wear,and both of them,respectively.

Thermal Fatigue Behaviour of Co-Based Alloy Coating Obtained by Laser Surface Melt-Casting on High Temperature Alloy

A thermal fatigue behaviour of Co-based alloy coating obtained by laser surface meltcasting on the high temperature alloy GH33 was studied.The results show that after each time of thermal cycling,the final residual stress was formed in the melt-casting layer which is attributed to the thermal stress and structural stress.Through the first 50 times of thermal cycling,the morphology of coating still inherits the laser casting one,but the dendrites get bigger;After the second 50 times of thermal cycling,corrosion pits emerge from coating,and mostly in the places where coating and substrate meet.The fatigue damage type of coating belongs to stress corrosion.

Microstructures and properties of Co-based alloy coatings prepared on surface of H13 steel

The Co-based alloy coatings had been prepared by laser cladding and vacuum fusion sintering. Microstructures of the coatings were investigated and the performance of thermal cycling was also tested using scanning electron microscopy （ SEM） and X-ray diffraction （ XRD ）. The results show that the coatings and substrates combine well. The main phase compositions of laser cladding coating are T-Co, Cr23 C6 and Ni2 9 Cro. 7 Feo. 36, while vacuum fusion sintering coating consists of Co, Cr7 C3, and Ni2.9 Cro. 7 Feo. 36. After thermal cycling, the minimum hot cracking width of laser cladding coating is 14 μm; moreover, laser cladding coating maintains high hardness and hot-cracking susceptibility. Those are beneficial to high temperature wear resistance of hot work dies.

Oxidation of a Co-base Superalloy

The oxidation behavior of a cast polycrystalline Co-base superalloy was studied at temperatures from 900 to 1050℃ and analyzed by thermogravimetric analysis （TGA）, X-ray diffraction （XRD） and scanning electron microscopy （SEM）. The results indicate that a cast Co-base superalloy follows the subparabolic oxidation kinetics at 900 and 1000℃, which are controlled by the growth of the inner Cr-rich layer, and that after oxidation at 1050℃ for 200 h, it almost exhibits the linear oxidation kinetics possible due to the volatility of Cr-rich oxide. A mixed scale forms on the alloy after prolonged oxidation. The oxide scale formed at 900 and 1000℃ is composed of an outer layer of spinel and an inner continuous Cr-rich layer and at I050℃ is composed of a very discontinuous Cr-rich layer.

Effect of Rare-earth Element La on Co-base Superalloy

The effect of La element on the mechanical properties and constitution nearby grain boundary in a Co-base superalloy Co-22Ni-22Cr-14k during 760℃ ageing has been investigated by AES and material testing. Results show that element La can be in a state of solid solution and segregates mainly at the vicinity of grain boundaries. The prior segregation of La atoms can affect segregation behaviour of other elements, so that exerts influence on microstructure of the alloy, Particularly increasing of La content can decrease P concentration at the vicinity of grain boundaries but not decrease S concentration. S together with La produce cosegregation effect. The content of La has no obvious effect on high temperature strength. When the content of La comes up to 0.02wt-％, it can obviously improve the high temperature ductility.

Preparation, Structures and Magnetic Properties of Two Co-based Clusters with Triangular Core and Cuboidal Core Geometries

Two novel Co-based clusters with the 2-(hydroxylmethyl)pyridine(hmpH)ligand,formulated as[Co3(hmp)6(hmpH)]×2NO3×3H2O(ZTU-3)and[Co4(hmp)4(CH3CO2)2(H2O)4]×2NO3(ZTU-4),have been successfully synthesized and structurally characterized.ZTU-3 features a triangular core geometry,while ZTU-4 exhibits a cuboidal core geometry.In addition,the magnetic properties of ZTU-3 and ZTU-4 are also all investigated.

High-Temperature Electric Properties and X-ray Photoemission Spectra of Layered Co-Based Oxides Bi_(2-x)La_xSr_2Co_2O_(8-δ)

Layered Co-based ceramics with a nominal composition Bi2-xLaxSr2Co2O8-δ (x=0.0, 0.4, 0.8, short by BLC-222) were prepared using conventional solid state reaction method. X-ray photoemission spectroscopy (XPS) was used to investigate their electronic structures. The cobalt ions are highly mixed valences of Co3+ and Co4+. The fraction of Co4+ almost keeps unchanged with the increase of x. The O-1s photoemission spectra show that there are lattice oxygen and chemical absorbed oxygen in all the samples. The substitution of Bi3+ by La3+ results in a change from metallic-like behavior to semiconductor behavior. This abnormal phenomenon means that La3+ plays a key role in effecting the electrical transport property of BLC-222. The O-Co covalence bond is strengthened by the increase of La3+, which results in the decrease of conductivity.

EFFECT OF TRACE ELEMENT B ON MICROSTRUCTURE OF DIRECTIONALLY SOLIDIFIED Co-BASE SUPER ALLOY DZX40M

The effect of trace element B on microstructure of directionally solidified new type Co-base superalloy is studied systematically in this paper. It is found that the addition of B makes the incipient melting temperature of the alloy decline remarkably. Compared with the alloy having a boron content of 0.05 %, the incipient melting temperature of the alloy with 0.7 % B decreases by 197℃. The primary and secondary dendrite arm spacings increase and the volume fraction of interdendritic carbides with fine microstructure becomes bigger with the enhancement of boron content. When the alloy is with 0.7wt %B, M3B2 precipitates in the interdendrites.

Effect of Laser Annealing on Permeability Spectra in Co-based Amorphous Ribbon

We investigated the variation of permeability spectra and relaxation frequency in Co-based amorphous ribbon annealed by pulsed Nd:YAG laser at various annealing energy Ea. The complex permeability spectra varies sensitively with the annealing energy, where the spectra could be decomposed into two contributions from domain wall motion,μdw(f) and rotational magnetization μrot(f) by analyzing the measured spectra as a function of driving ac field amplitude. The magnitude of μdw(f) and μrot(f) in dc limit shows maximum at Ea = 176 mJ. The maximum relaxation frequency for rotational magnetization, determined by μ'(f) curve, is about 700 kHz at Ea=62 mJ but that for wall motion is about 26 kHz at 230 mJ. These variations reflect the increase of magnetic softness and microstructural change by the annealing.

Microstructural Evolution of a Ni-base Alloy DZ468 Joint Bonded with a New Co-base Filler

Ni-base alloy DZ468 has been joined by transient liquid phase bonding technique with a newly developed Co-based filler. The microstructures of the Co-base filler and the joint, the effects of heat treatment on microstructure and hardness of the joint have been investigated by various experimental methods. Results show that the Co-base filler consists of γ, M2B, M5B3 and M23B6 phases. Because of the interdiffusion between the base metal and the filler, γ, MC, M5B3 and M23B6 phases are formed in the bonding zone. And localized liquidation of substrate occurs in the diffusion affected zone, with MC and M3B2 precipitating in this area. During heat treatment, the volume of the intermetallic phases in the bonding zone resulting from incomplete isothermal solidification decreases obviously. On the contrary, the width of the diffusion affected zone increases at the solution stage and subsequently decreases at the aging stages.

矿物掺合料对水泥砂浆TSA侵蚀的影响

研究了硅灰、粉煤灰、矿渣对水泥砂浆TSA侵蚀的影响,采用掺30%石灰石填料的砂浆件,测试各砂浆在5±1℃的2%MgSO4溶液中浸泡1年后的外观、强度及矿物成分变化。结果表明:掺石灰石粉使水泥砂浆受侵蚀后表面呈软泥状,主要腐蚀产物为硅灰石膏和石膏,表现为典型的TSA破坏特征,其强度损失率大于纯水泥砂浆。矿物掺合料的加入降低了水泥石中CH晶体含量,从而在一定程度上提高了水泥砂浆的抗TSA侵蚀能力。矿物掺合料对水泥石中CH晶体的减少与对抗TSA侵蚀性的改善效果具有相同的规律,其优劣次序为:60%矿渣粉>5%硅灰+25%矿渣粉>8%硅灰>30%矿渣粉>20%粉煤灰>无掺合料。

APF中数字低通滤波器的设计及仿真实现

本文介绍了基于瞬时无功功率理论的i_p-i_q谐波检测方法及对低通滤波器的要求,分析了数字低通滤波器的类型、阶数及截止频率对有源电力滤波器谐波检测效果的影响。利用MATLAB仿真软件设计了二阶巴特沃思(Butterworth)数字低通滤波器,对i_p-i_q谐波检测算法进行了仿真研究,仿真结果证明所选择的数字低通滤波器正确性。

Effects of recrystallization on the low cycle fatigue behavior of directionally solidified superalloy DZ40M

The effects of recrystallization on low cycle fatigue behavior were investigated on directionally solidified Co-base superalloy DZ40M. Optical microscopy and SEM were used to examine the microstructure and fracture surface of the specimens. The mechanical testing results demonstrated that the low cycle fatigue property of DZ40M significantly decreased with the partial recrystallization. Fatigue cracks initiate near the carbides and the grain boundaries with slip-bands. Both the fatigue crack initiation and propagation can be accelerated with the occurrences of recrystallized grain boundaries.

HIGH TEMPERATURE FATIGUE BEHAVIOUR OF A DIRECTIONALLY SOLIDIFIED COBALT-BASE SUPERALLOY

The high temperature high cycle fatigue behaviour of a directionally solidified Co-base superalloy was investigated. The alloy has saperior fatigue resistance at 900℃ and its fatigue strength is up to 295MPa. Its σ-Nf curve is characterized by three distinct zones. The stronger dependence of Nf on or in the high .and low stress zones results from multiple fatigue crock initiation sites produced by high stress and oxidation effect in a prolonged exposure, respectively.

Recent progress in Co-based metal-organic framework derivatives for advanced batteries

To date,Co-based metal-organic frameworks(Co-MOFs)have drawn much attention owing to their advantages of easy preparation,high porosity and adjustable structure.Because of these enticing properties,numerous efforts have been devoted to their applications in energy storage and conversion.However,poor conductivity has become one of the biggest obstacles for large-scale use of pristine Co-MOFs.Subsequently,many attempts have been carried out to develop various Co-MOF derived materials as electrodes for rechargeable batteries in order to address the above-mentioned shortcoming and to enhance the electrical conductivity with improved stability during cycling.Moreover,in addition to improvement of Li-ion batteries in practical utilization,seeking for other rechargeable batteries is another urgent task due to the high cost and limited sources of metallic Li.Herein,by following the recent research progress,this review provides an overview of applications of Co-MOF derived materials in various rechargeable batteries including lithium-ion batteries,sodium-ion batteries,lithium-sulfur batteries,zinc air batteries and other rechargeable batteries,where they have been utilized as cathodes,anodes,separators and electrocatalysts.Accordingly,we categorize and compare the morphology driven electrochemical performance of various Co-MOF derivatives including porous carbon,cobalt oxides,cobalt chalcogenides,cobalt phosphides and corresponding composites.Finally,current challenges for large-scale production and commercialization of Co-MOF derived materials as well as some reasonable solutions have been discussed at the end.

Selective Laser Melting of Carbon-Free Mar-M509 Co-Based Superalloy:Microstructure,Micro-Cracks,and Mechanical Anisotropy

In this work,the microstructural evolution,micro-crack formation,and mechanical anisotropy of the selective laser melted(SLM)carbon-free Mar-M509 Co-based superalloy were systematically studied under different linear energy densities(LED).Observation shows that the SLM Mar-M509 superalloy possesses a fully dense structure,whereas some microcracks exist along the building direction.The electron backscatter diffraction results reveal that dominant columnar grains tend to elongate along the building direction parallel to the XZ plane.Meanwhile,both a<001>near fiber texture and a{100}<001>near sheet texture are observed in different specimens.For the specimen with fiber texture,a high misorientation angle exists among different columnar grains,which aggravated the generation of micro-cracks under thermal stress.Higher LED results in higher micro-crack density in the SLM specimen due to higher thermal stress.Mar-M509 specimen fabricated under lower LED exhibits higher tensile strength due to more significant grain refinement.More prominent anisotropy of tensile performance was found in the high LED specimen,which can be attributed to the higher density of micro-cracks and crystallographic texture.Furthermore,the SLM Mar-M509 superalloy exhibits better mechanical properties than the traditional cast technique.In summary,this work can contribute to the development and the future application of SLM-fabricated Co-based superalloy.

Effect of post-bond heat treatment on the microstructure and high temperature mechanical property of a TLP bonded γ'-strengthened co-based single crystal superalloy

Post-bond heat treatment(PBHT) applied to a transient liquid phase(TLP) bonding joint is an effective approach to remove the brittle borides and improve its properties.Herein,we proposed two types of PBHT strategies to obtain a TLP bonded γ'-strengthened Co-based single crystal superalloy,and the microstructural characteristics and tensile properties of the two heat treated joints were compared to identify the optimal PBHT strategy.The evolution of the brittle boride in the joint after the PBHT was studied by using in-situ microscopy.The experimental results allowed to provide a theoretic model to quantitatively evaluate the distribution of the brittle phase after the optimal PBHT and analyze the joint fractures to understand the failure mechanisms.The obtained results revealed that a post-bond solid solution treatment performed to the joint at a high temperature(over 1275℃) could decrease the area fraction of the boride from 7.2 % to 1.4 % and increase the elongation from 1.9 % to 7.8 %.This work emphasizes the relevance of solid solution temperature when a PBHT strategy is applied.

Experimental investigation of a Portevin-Le Chatelier band in Ni–Co-based superalloys in relation toγ’precipitates at 500℃

The macroscopically localized deformation behaviors of Ni–Co-based superalloys with differentγ’precipitate content were investigated at 500?C and 1×10-4 s-1 via an in situ method namely,digital image correlation(DIC).The DIC results showed that the serrated flow of the stress–strain curves was accompanied by localized deformation of the specimens.The fracture morphology was characterized mainly by transgranular fracture with numerous dimples in the lowγ’content alloy,and intergranular fracture with large fracture section in the highγ’content alloy.The Portevin–Le Chatelier(PLC)effect occurred in the investigated Ni–Co-based superalloys.Furthermore,the localized deformation of the highγ’content alloy was more severe than that of the lowγ’content alloy,and the band width was slightly larger.Moreover,for the first-time ever,a special propagation feature,namely±60?zigzag bands characterized by head-to-tail connections,was observed in the highγ’content alloy.

The highly dispersed Co-based nanoparticles encapsulated into porous N-doping carbon polyhedral with the low content of Ru modification as a promising cathode catalyst for long-life Li-O_(2)batteries

Lithium(Li)-O_(2)batteries have triggered worldwide interest due to their ultrahigh theoretical energy density.However,it is a long shot for the grand-scale applications of Li-O_(2)battery at current stage owing to its significant polarization,inferior cycling life,and irreversible decomposition of Li2O_(2).Herein,a facile way of preparing the highly dispersed Co-based nanoparticles encapsulated into porous N-doping carbon polyhedral with the low content of Ru modification(LRu@HDCo-NC)is explored through the pyrolysis of Co/Zn based zeolitic imidazole frameworks(ZIFs)containing Ru-based ligands.Even with the very small amount of Ru introduction(1.8%),LRu@HDCo-NC still exhibits the superior oxygen evolution reaction/oxygen reduction reaction(OER/ORR)performance and also inhibits side reactions in Li-O_(2)battery because of the abundant pores,plentiful surface N heteroatoms,and highly dispersed metal-based sites which are induced by the volatilization of Zn,and conductive/stable carbon skeleton derived from ZIFs.When applied in Li-O_(2)batteries,LRu@HDCo-NC cathode delivers a high discharge capacity of 15,973 mAh·g^(-1)at 200 mA·g^(-1),good capacity retention at higher rate(12,362 mAh·g^(-1)at 500 mA·g^(-1))and outstanding stability for>300 cycles with low voltage polarization of<2.3 V under a cut-off capacity of 1,000 mAh·g^(-1)at 500 mA·g^(-1).More critically,a series of ex situ and in situ characterization technologies disclose that the LRu@HDCo-NC cathodes can effectively promote the reversible reactions in Li-O_(2)batteries.