Technical parameters of drawing and coal-gangue field movements of a fully mechanized large mining height top coal caving working face

Under fully mechanized, large mining height top coal caving conditions, the shield beam slope angle of the support increases due to the enlargement of the top coal breaking and caving space. This results in a change of the caving window location and dimensions and, therefore, the granular coal-gangue movement and flows provide new characteristics during top coal caving. The main inferences we draw are as follows. Firstly, after shifting the supports, the caved top coal layer line and the coal gangue boundary line become steeper and are clearly larger than those under common mining heights. Secondly, during the top coal caving procedure, the speed of the coal-gangue flow increases and at the same drawing interval, the distance between the coal-gangue boundary line and the top beam end is reduced. Thirdly, affected by the drawing ratio, the slope angle of the shield beam and the dimensions of the caving window, it is easy to mix the gangue. A rational drawing interval will cause the coal-gangue boundary line to be slightly behind the down tail boom lower boundary. This rational drawing interval under conditions of large mining heights has been analyzed and determined.

Breakage and separation mechanism of ZGM coal mill based on parameters optimization model

Sampling ports were firstly drilled on a ZGM95 coal mill in the power plant in China, and the coal samples from various points in the pulverizer were collected under the different operation conditions. The prop- erty of the sampling material from the mill was analyzed, applying the float-sink test, size distribution analysis, proximate analysis and so on. It was indicated that the ＋250 I^m fraction in the pulverized fuel accounted for only 0.02%, while it was 83.2% in the new feed. The circulating ratio and coal flow in the separator and the cone zone were calculated using the mass balance of the circulating load. So, the cir- culating ratio in the separator of the pulverizer was between 8 and 13, and the circulating ratio, the feed flow of separator and cone zone all raised with the increase of the air volume. Furthermore, the parameters of the separation functions were obtained based on the fitting method. It was shown that the mean value of the shape factor B was 0.7617, and the parameter D which is the particle size at 50% cumulative yield in the separator almost kept unchanged.

Additivity of pore structural parameters of granular activated carbons derived from different coals and their blends

A series of granular activated carbons （GACs） were prepared by briquetting method from Chinese coals of different ranks and their blends, with coal pitch as the binder. Pore structural parameters including BET specific surface area （SBEr）, total pore volume （Vr） and average pore diameter （da） were measured and cal- culated as well as process parameters such as yield of char （CY） and burn-off （B）. The relationship between the pore structural parameters of the GAC from coal blend （BC-GAC） and the ones of the GACs from corresponding single coals （SC-GACs） was analyzed, in which an index, the relative error （δ）, was presented to define the bias between fitted values and experimental values of these parameters of the BC-GACs. The results show that the BC-GAC keeps qualitatively the pore structural features of the SC-GACs; as concerned as the quantitative relationship, the pore structural parameters of the BC-GAC from coal blend consisting of non-caking coals can be obtained by adding proportionally the pore structural parameters of the SC-GACs with a less than 10%. Meanwhile, for the BC-GAC from coal blend containing weak caking bituminous coal, the δ increases up to 25% and the experimental pore size distribution differs greatly from the fitted one.

Experimental Study on the Mechanical Parameters Relating to the Impact Tendency of Coal Sample

Coal burst remains one of the gravest safety risks that will be encountered in mining in the future, because the stress conditions will become more complex as mining depths increase. Various influencing elements exist, and varied geological and mining circumstances might result in diverse coal burst phenomena. The impact propensity of coal has variations as a result of the distinct physical and mechanical qualities of each. To identify the impact propensity of coal and then understand the rules of coal burst occurrence, laboratory tests can be conducted to identify the physical and mechanical parameters affecting coal samples. The mechanical properties, energy absorption, and energy dissipation characteristics of coal samples were examined experimentally in this paper using coal samples that were taken from the mine. On the basis of the evaluation of the impact inclination parameters for four fundamental coal samples, novel impact inclination indicators and the relationship between the fractures in the coal sample and the impact inclination parameters were discussed. The following are the key conclusions: 1) On-site samples of No. 15 coal from the Qi yuan Coal Mine were taken (15 s) and processed in accordance with the guidelines for the coal specimen impact inclination test. The accuracy of the specimen was sufficient for the test. 2) Analysis is done on the mechanical relevance and calculation techniques of the four fundamental coal sample impact tendency characteristics, dynamic failure time (DT), elastic strain energy index (WET), impact energy index (KE), as well as uniaxial compressive strength (RC). 3) Regarding the rock burst danger of rock samples, the potential use of the ratio of pre-peak and post- peak deformation modulus to Kλ and the residual elastic strain energy index CEF as the impact propensity indices of coal samples are discussed. It is possible to utilize two new impact propensity indices to evaluate the impact propensity of coal samples, according to test results that reveal a linear correlation between two new impact inclination indexes and four fundamental impact tendency indexes. 4) The statistical analysis of the crack ratio with the four impact propensity indicators after coal specimen failure, and the correlation among the crack ratio with the indicators, are both done. The findings indicate that the four impact propensity indicators have a linear relationship with the crack ratio of the coal sample surface cracks.

Experimental simulation and numerical analysis of coal spontaneous combustion process at low temperature

The characteristic of coal spontaneous combustion includes oxidative property and exothermic capacity. It can really simulate the process of coal spontaneous combustion to use the large scale experimental unit loading coal 1 000 kg. According to the field change of gas concentration and coal temperature determined through experiment of coal self ignite at low temperature stage, and on the basis of hydromechanics and heat transfer theory, some parameters can be calculated at different low temperature stage, such as, oxygen consumption rate, heat liberation intensity. It offers a theoretic criterion for quantitatively analyzing characteristic of coal self ignite and forecasting coal spontaneous combustion. According to coal exothermic capability and its thermal storage surroundings, thermal equilibrium is applied to deduce the computational method of limit parameter of coal self ignite. It offers a quantitative theoretic criterion for coal self ignite forecasting and preventing. According to the measurement and test of spontaneous combustion of Haibei coal, some token parameter of Haibei coal spontaneous combustion is quantitatively analyzed, such as, spontaneous combustion period of coal, critical temperature, oxygen consumption rate, heat liberation intensity, and limit parameter of coal self ignite.

A New Parameter as an Indicator of the Degree of Deformation of Coals

The deformation of coal is effected by thermal effect, pressures and tectonic stress, and the tectonic stress is the principal influence factor. However, the proposition of a useful quantitative index that responds to the degree of deformation of coals quantitatively or semi-quantitatively has been a long-debated issue. The vitrinite reflectance ellipsoid, that is, the reflectance indication surface（RIS） ellipsoid is considered to be a strain ellipsoid that reflects the sum of the strain increment caused by stress in the process of coalification. It has been used to describe the degree of deformation of the coal, but the effect of the anisotropy on the RIS ellipsoid has not yet been considered with regards to non-structural factors. In this paper, Wei＇s parameter（ε） is proposed to express the deformation degree of the strain ellipsoid based on considering the combined influence of thermal effect, pressure and tectonic stress. The equation is as follows： ε=√[（ε_1-ε_0）~2＋（ε_2-ε_0）~2＋（ε_3-ε_0）~2]/3, where ε_1=lnR_（max）, ε_2=lnR_（int）, ε_3=lnR_（min）, and ε_0=（ε_1＋ε_2＋ε_3）/3. Wei＇s parameter represents the distance from the surface to the spindle of the RIS logarithm ellipsoid; thus, the degree of deformation of the strain ellipsoid is indicated quantitatively. The formula itself, meanwhile, represents the absolute value of the degree of relative deformation and is consequently suitable for any type of deformation of the strain ellipsoid. Wei＇s parameter makes it possible to compare degrees of deformation among different deformation types of the strain ellipsoid. This equation has been tested in four types of coal： highly metamorphic but weakly deformed coal of the southern Qinshui Basin, highly metamorphic and strongly deformed coal from the Tianhushan coal mining area of Fujian, and medium metamorphic and weakly or strongly deformed coal from the Huaibei Coalfield. The results of Wei＇s parameters are consistent with the actual deformation degrees of the coal reservoirs determined by other methods, which supports the effectiveness of this method. In addition, Wei＇s parameter is an important complement to the indicators of the degrees of deformation of coals, which possess certain theoretical significance and practical values.