Optimization of Hydrocracking Process for Enhanced BTX Production from Coal Tar-Derived Hydrorefined Products

Hydroconversion of coal tar to produce aromatic hydrocarbons(BTX)represents a crucial strategy for the highvalue hierarchical utilization of coal.This study focused on the hydrocracking of hydrorefined products derived from coal tar to enhance the production of benzene,toluene,and xylene(BTX).Various reaction conditions,including reaction temperature,hydrogen pressure,space velocity,and hydrogen-to-oil volume ratio,were systematically explored to optimize BTX yields while also considering the process’s economic feasibility.The results indicate that increasing the reaction temperature from 360℃ to 390℃ significantly favors the production of BTX,with yields increasing from 21.42%to 41.14%.Similarly,an increase in hydrogen pressure from 4 MPa to 6 MPa boosts BTX production,with yields rising from 36.31%to 41.14%.Reducing the space velocity from 2 h^(-1) to 0.5 h^(-1) also favors the BTX production process,with yields increasing from 37.96%to 45.13%.Furthermore,raising the hydrogen-to-oil volume ratio from 750 to 1500 improves BTX yields from 41.61%to 45.44%.Through economic analysis,the optimal conditions for BTX production were identified as a reaction temperature of 390℃,hydrogen pressure of 5-6 MPa,space velocity of 1 h^(-1),and hydrogen-to-oil volume ratio of 1000,achieving a BTX yield of 43.73%.This investigation highlights the importance of a holistic evaluation of hydrocracking conditions to optimize BTX production.Furthermore,the findings offer valuable insights for the design and operation of industrial hydrocracking processes aimed at efficiently converting coal tar-derived hydrorefined feedstock into BTX.

Preparation of pitch precursor with excellent spinnability for general-purpose carbon fibre using coal tar pitch as raw material

Tetrahydrofuran(THF) extract of coal tar pitch(CTP) was used instead of blending CTP with pretreated pyrolysis fuel oil to prepare an isotropic pitch precursor with excellent spinnability for general-purpose carbon fibre through bromination-dehydrobromination. The feasibility and effectiveness of synthesising an isotropic pitch precursor derived from THF-soluble(CTP-THFs) is demonstrated in this study.The results show that CTP-THFs contains more light components than CTP;CTP-THFs and CTP monomer proportions were 62.52% and 45.32%, respectively. However, based on comparisons of CTP-THFsBr0 and CTPBr0 characterisations, CTP-THFs exhibits better polycondensation than CTP. Bromination-dehydrobro mination promotes polycondensation of pitch precursors, leading to greater carbon aromaticity in CTP-THFsBr5, CTP-THFsBr10, and CTP-THFsBr15 than that in CTP-THFsBr0 and CTPBr0. CTP-THFsBr5 and CTP-THFsBr10 have excellent spinnability even with softening points as high as 230 ℃. The pericondensed carbon and carbon aromaticity of CTP-THFsBr5 and CTP-THFsBr10 are high owing to the higher degree of polycondensation;however, they still possess a more linear molecular structure. The as-prepared carbon fibre exhibits homogeneity and uniformity, and the mechanical performance is comparable with that of commercial general-purpose carbon fibre products.

Ultra-deep Removal of Metal Ions from Coal Tar by Complexation:Experimental Studies and Density Functional Theory Simulations

As one of the important aspects of upgrading coal tar,the ultra-deep removal of metal ions via the complexation method was investigated by screening four complexing agents and performing density functional theory(DFT)simulations.Analysis of the compositions and contents of the metallic compounds in the coal tar revealed that the main components were iron and calcium naphthenates.Direct filtration reduced the mechanical impurity content from 0.24%to 0.0752%,indicating that most of the large particles could be easily removed.Among the four complexing agents,namely,acetic acid,oxalic acid,citric acid,and ethylenediaminetetraacetic acid,oxalic acid exhibited the best demetallization performance.The DFT simulations suggested that the high performance of oxalic acid originated from its 1:1 coordination mode,rigid dicarboxyl structure,and greater binding energy.

Separation and analysis of six fractions in low temperature coal tar by column chromatography

The low temperature coal tar(CT)is taken as the raw material,and the extraction and column chromatography are used for detailed and accurate characterization in this paper.The n-heptane soluble fraction(CT-HS)and insoluble fraction(CT-HI)were obtained by n-heptane Soxhlet extraction.The extraction rate of CT-HS reached 92.79%(mass),which indicated that there are few heavy compounds in it.Further,different solvents(methylbenzene,benzene,ethyl acetate,methylbenzene-ethanol)were used to elute CT-HS by chromatographic column to obtain five fractions(saturates,aromatics,heteroatoms,phenolics and resins,named CT-SA,CT-AR,CT-HE,CT-PH,CT-RE,respectively).The yields of CTSA,CT-AR,CT-HE,CT-PH,CT-RE are 42.12%,10.43%,2.19%,9.50%and 6.63%(mass),respectively.Gas chromatography-mass spectrometry analysis of eluting components show that alkanes are the main components in CT,followed by polycyclic aromatics,and the corresponding fractions are CT-SA and CT-AR,respectively.The relative content of aliphatics in CT-SA is 76.93%,and the relative content of aromatics in CT-AR is 75.05%.This separation technology effectively separates and enriches different components in CT,and the activation energy required for the pyrolysis process of a single eluting fraction is lower than that of CT,which is expected to provide an important reference for the separation,analysis and conversion of complex oil products such as coal-oil co-processing products,coal tar and other complex heavy carbon oil products.

Feasibility Investigation of Bitumen Properties by Blending of Coal Tar Pitch

There are numerous methods and additives available to improve the durability and quality of road bitumen. A coal tar obtained by coal coking was distilled in a laboratory into fractions of initial boiling point IBP-180℃ (gasoline-like fuel), 180℃ - 360℃ (diesel-like fuel), and >360℃ (residue or coal tar pitch). The coal tar pitch was added into road bitumen by up to 1 - 5 wt% and investigated the alteration of physical and chemical properties. The physico-mechanical properties of coal tar pitch and bitumen blends, as well as the chemical group composition, were determined using standard techniques (MNS) and the SARA method, respectively. Results of 3% coal tar pitch addition into bitumen enhanced ductility by 12.4% and softening point by 1.6℃. We found that blending with bitumen coal tar pitch as a modifier could improve bitumen properties.

Selective preparation of light aromatic hydrocarbons from catalytic fast pyrolysis vapors of coal tar asphaltene over transition metal ion modified zeolites

The catalytic cracking of coal tar asphaltene(CTA)pyrolysis vapors was carried out over transition metalion modified zeolites to promote the generation of light aromatic hydrocarbons(L-ArHs)in a pyrolysisgas chromatography/mass spectrometry(Py-GC/MS)micro-reactor system.The effects of ultra stable Y(USY),Co/USY and Mo/USY on the selectivity and yield of L-ArHs products and the extent of deoxygenation(Edeoxygenation),lightweight(Elightweight)from CTA pyrolysis volatiles were investigated.Results showed that the yields of L-ArHs are mainly controlled by the acid sites and specific surface area of the catalysts,while the deoxygenation effect is determined by theirs pore size.The Eligltweight of CTA pyrolysis volatiles over USY is 9.65%,while the Edeoxygenation of CTA pyrolysis volatiles over Mo/USY reaches 20.85%.Additionally,the modified zeolites(Mo/USY and Co/USY)exhibit better performance than USY on L-ArHs production,owing to the synergistic effect of metal ions(Mo,Co)and acid sites of USY.Compared with the non-catalytic fast pyrolysis of CTA,the total yield of L-ArHs obtained over USY(4032 mg·kg^(-1)),Co/USY(4363 mg·kg^(-1))and Mo/USY(4953 mg·kg^(-1))were increased by 27.03%,38.19%and 54.78%,respectively.Furthermore,the possible catalytic conversion mechanism of transition metal ion(Co and Mo)modified zeolites was proposed based on the distribution of products and the characterizations of catalysts.

Efficient separation of phenols from coal tar with aqueous solution of amines by liquid-liquid extraction

In this paper,a method of extracting phenols from coal tar by amines aqueous solution was proposed.The effects of various amines on the extraction properties of phenols in coal tar were researched from the views of molecular structure.The parameters such as molar ratio,concentration,extraction time and temperature for the extraction of coal tar by the monoethanolamine and ethylenediamine aqueous solution were examined.The results show that the organic amine with more amino groups,hydroxyl structure and strong electronegativity exhibited better extraction performance.Under the optimal conditions,the extraction yields of phenols in coal tar by the monoethanolamine or ethylenediamine aqueous solution are above 80%,and the recovery yields of amines reach 99%.Furthermore,the probable geometries of complexes formed by the combination of phenols and organic amines were calculated by density function theory.In addition,several thermodynamic models were evaluated through comparing the relative deviation of simulation results by ASPEN PLUS to the experimental ones,which provide feasibility thermodynamic models for the simulation of extraction process.The present work affords a mild,efficient and green approach for the extraction of phenols from coal tar by an aqueous solution of amines in industry application.

Coal Tar Derived Metallocene Catalyst for Polymerization of 1-Decene into Low-viscosity Poly-α-Olefin Lubricating Base Oil

The production of poly-α-olefins(PAOs)has attracted attention due to their excellent viscosity-temperature dependence,wear characteristics,oxidative properties,and high thermal stability.In this study,indene extracted during coal tar refining was used as a raw material to synthesize a bis(indenyl)zirconium dichloride metallocene catalyst.A PAO with low viscosity and a high viscosity index was produced via the oligomerization of 1-decene in the presence of both the prepared metallocene and a methylaluminoxane(MAO)co-catalyst.Notably,the effects of different synthesis reaction parameters,such as Al:Zr ratio,amount of catalyst,and reaction temperature,on the conversion ratio and product selectivity were investigated in detail.The produced PAO was thoroughly characterized using Fourier-transform infrared,^(13)C,and^(1)H nuclear magnetic resonance spectroscopies;gas chromatography;and viscosity measurements.At 70℃,the metallocene catalyst created more stable active sites.In addition,the alkylation effect of MAO was noticeable.Interestingly,the obtained catalysis results demonstrated that a high conversion ratio of~93%was achieved at a low reaction temperature of 70℃,with a catalyst dosage of 0.0848 mmol and Al:Zr ratio of 8.48mmol:0.0848mmol.Moreover,under these optimal conditions,the kinematic viscosity of PAO was 4.25 mm2/s at 100℃,and the viscosity index was 139,indicating good viscosity-temperature properties.

Characterization of Coal Tar Pitch and Paving Pitch by UV,EA and NMR

In order to enlarge the use of coal tar pitch(CTP) in paving road,CTP and 60th paving pitch (PP) were extracted by n-heptane,toluene and ethanol step by step in a Soxhlet apparatus.The three fractions of CTP and PP were detected using UV-absorption(UV-A),elemental analyses(EA) and nuclear magnetic resonance(NMR) firstly as a whole unit after quality characterization of physical nature of CTP and PP were finished.The CTP had more saturate aliphatic and residue compounds dissolved in ethanol.On the other hand there were more continental type structures of aromatic ring than that of PP.There was almost no residue in PP after extracted by ethanol.The results explained why CTP was crisp in cold winter and was soften in summer.The following research will focus on how to change the chemical construction of CTP into the relative similar structures with those of PP through adding polymer.

Determination of the volatile fraction of coal tar

The coal tar was qualitative and quantitative anMyzed by gas chromatography （GC） method. 74 components were identified exactly by gas chromatographY-mass spectrometry （GC-MS）. 31 components （37%） were quantitatively analyzed by gas chromatography-flame ionization detector （GC-FID）. The linearity, accuracy, precision, limit of detection （LOD） and limit of quantitative （LOQ） determination were inspected. The scope of quantitative analysis by CC was discussed. The experimental results of thermogravimetric analysis （TGA） proved that GC quantitative analysis of the coal tar was reliable.

Carbon foams prepared from coal tar pitch for building thermal insulation material with low cost

A new approach is provided to resolve the large-scale applications of coal tar pitch. Carbon foams with uniform pore size are prepared at the foaming pressure of normal pressure using coal tar pitch as raw materials. The physical and chemical performance of high softening point pitch(HSPP) can be regulated by vacuumizing owing to the cooperation of vacuumizing and polycondensation. Results indicate that the optimum softening point and weight ratio of quinoline insoluble are about 292℃ and 65.7%, respectively. And the optimum viscosity of HSPP during the foaming process is distributed in the range of 1000-10000 Pa·s. The resultant carbon foam exhibits excellent performance, such as uniform pore structure, high compressive strength(4.7 MPa), low thermal conductivity(0.07 W·m^(-1) ·K^(-1)), specially, it cannot be fired under the high temperature of 1200 ℃.Thus, this kind of carbon foam is a potential candidate for thermal insulation material applied in energy saving building.

Simulation of Low-Temperature Coal Tar Hydrocracking in Supercritical Gasoline

The aim of this paper was preliminary design of the process for low-temperature coal tar hydrocracking in supercritical gasoline based on Aspen Plus with the concept of energy self-sustainability.In order to ensure the correctness and accuracy of the simulation,we did the following tasks:selecting reasonable model compounds for low-temperature coal tar;describing the nature of products gasoline and diesel accurately;and confirming the proper property study method for each block by means of experience and trial.The purpose of energy self-sustainability could be possibly achieved,on one hand,by using hot stream to preheat cold stream and achieving temperature control of streams,and on the other hand,by utilizing gas(byproduct of the coal tar hydrocracking)combustion reaction to provide energy.Results showed that the whole process could provide a positive net power of about 609 kW·h for processing the lowtemperature coal tar with a flowrate of 2 268 kg/h.The total heat recovery amounted to 2 229 kW·h,among which 845kW·h was obtained from the gas combustion reaction,and 1 116 kW·h was provided by the reactor’s outlet stream,with the rest furnished by hot streams of the products gasoline,diesel and residue.In addition,the process flow sheet could achieve products separation well,and specifically the purity of product gasoline and diesel reached 97.2%and 100%,respectively.

Chemical composition and structure characterization of distillation residues of middle-temperature coal tar

The distillation residues of middle-temperature coal tar(DRMCT) were separated into saturate, aromatic, resin and asphaltene fractions by using the combination of solvent extraction and column chromatography separation.The isolated four fractions have been further characterized through the combination of elemental analysis,Fourier transform infrared(FTIR) spectra, proton nuclear magnetic resonance spectrum(~1H NMR) and molecular weight analysis. The analysis results confirm the view that the saturate fraction from DRMCT was mainly composed of long-chain alkanes and almost all of the heteroatoms(S, N and O) were existed in aromatic structures.The asphaltene fraction had the highest molecular weight, the most amount of heteroatom(especially oxygen)and was the most condensed with shortest alkyl side chains among all the fractions. In addition, for the heavier components, the resin and asphaltene fractions from DRMCT contained lower ratio of H/C, lower molecular weight and higher aromaticity degree when compared with crude oils.

Experimental Study of Integrated Ebullated-bed and Fixed-bed for Hydrotreating Mid-Low Temperature Coal Tar to Clean Fuel

A new hydrotreating technology integrating the ebullated-bed(EB) and the fixed-bed(FB) hydrogenation was proposed to investigate the efficiency for hydrotreating mid- low-temperature coal tar to clean fuel, and multiple tests at the bench scale were carried out. The results showed that the distillates obtained from EB reactors were greatly upgraded and could meet the requirements of FB unit without discarding any tail oil. The naphtha produced from FB reactors could be fed to the catalytic reforming unit, while a high quality diesel was also obtained. The unconverted oil(UCO) could be further hydrocracked to clean fuel. It is found that the removal of impurities from the coal tar oil is related with the molecular aggregation structure and composition of the coal tar. Application of the integrated hydrotreating technology to the hightemperature coal tar processing demonstrated that more than half of heavy components could be effectively upgraded.

Comparative Study of the Modification of Coal Tar Pitch for Higher Carbonization Yield and Better Properties

Parent coal tar pitch(CTP)was modified with boric acid(BA),cinnamaldehyde(CMA)and the mixture of BA and CMA,respectively.The parent CTP and three modified CTPs were characterized by elemental analysis,thermogravimetric analysis,Fourier transform infrared(FT-IR)spectroscopy and scanning electron microscopy.The four samples were carbonized at different temperatures and resultant carbonized products were characterized by FT-IR spectroscopy,X-ray diffraction and polarized-light microscopy.The results show that the morphologies and carbonization behaviors of the parent CTP and modified CTPs are quite different.The carbonization yield of the CTP modified with the mixture of BA and CMA is higher than that of CTP modified with BA or CMA only.In addition,the modification of CTP with 7 g of BA and 10 ml of CMA results in an increase in carbonization yield by5.64%.During the pyrolysis of modified CTPs,the dehydration of BA or the distillation of CMA occurs at the temperature lower than 300°C,and methyl and methylene groups of the modified CTPs disappear gradually as temperature rises.Furthermore,the modification of CTP by the mixture of BA and CMA results in more intensive mesophase spheres than other modified CTPs,and the modified CTP is easier to be carbonized to form graphitic carbon.

Advancement of Hydro-Desulfurization Catalyst and Discussion of Its Application in Coal Tar

This paper describes the influences of active metal, promoter and chelating agent on the properties of hydro-desulfuri-zationcatalyst. The use of chelating agent, especially its combination with common promoters e.g., EDTA-P, has an important meaning to develop highly active catalyst, specifically to unify the active metal dispersion degree and sulfurization degree in some extent, however, they are contradictory in conventional cognition. In the aspect of carriers, composition and nanometer carriers have more excellent performances in acidity, pores structureand metal-carrier interaction than common carriers, and are the developing trend in the future and should be a breakthrough mainly in preparation methods. We also pointed out the decisive factors to improve the activity of the catalyst: higher sulfurization degree of active metal oxide and higher aspect ratios of active phase crystal morphology, and the proper acidity and pores structure can be considered the key factors for deep desulfurization whose mainly obstacle is the desulfurization of large rigid molecules, e.g., dibenzothiophene and 4, 6-dimethyl substituted dibenzothiophene. Based on above that, We discussed the suitable hydrodesulfurization (HDS) catalyst for coal tar, aiming at providing some theoretical guidance for the “design” of coal tar HDS catalyst.

Development of a Raoult’s Law-Based Screening-Level Risk Assessment Methodology for Coal Tar and Its Application to Ten Tars Obtained from Former Manufactured Gas Plants in the Eastern United States

A Raoult’s law-based screening-level assessment methodology was developed to calculate the carcinogenic and non-carcinogenic risks from ingestion of coal tar-contaminated water and it was applied to ten coal tars obtained from sites in the eastern United States. This approach provides a simple risk screening based on the conservative assumptions of Tier 1 in both the ASTM RBCA methodology and the USEPA Soil Screening Guidance. Results across the ten tars exhibited similar patterns, even though the coal tars had significantly different chemical compositions, and in all cases the screening-level risks were above the USEPA thresholds. There was no appreciable difference in the total risks when using either the current USEPA 1993 PAH risk assessment guidance or the proposed 2010 guidance. Benzene, while present at low concentrations within the coal tars, posed the dominant risk and strong correlations were observed with the benzene mole fraction.

A strategy based on water soluble coal tar pitches to construct MnO_(2)@C composite materials with high electrochemical performance

The water soluble coal tar pitches(WS-CTPs)were successfully prepared and used to construct the MnO_(2)@C composite materials by a hydrothermal method.It is interestingly observed that the structures and morphologies of MnO_(2)@C materials can be controlled by controlling the dosages of WS-CTPs and KMnO4.Meanwhile,it is aware that MnO_(2)exists in the MnO_(2)@C materials in an amorphous state.Compared with MnO_(2),MnO_(2)@C materials output a remarkable improvement in electrochemical performance.For instance,MnO_(2)@C-0.3 shows the storage capacity at 965.7 mA h g^(−1)after 300 cycles at a current density of 0.1 A g^(−1).In addition,after 600 cycles at a current density of 1.0 A g^(−1),the storage capacity of MnO_(2)@C-0.3 still keeps 450.3 mA h g^(−1),indicating that MnO_(2)@C-0.3 owns tremendous cycle stability at a high current density.In view of the fact that the coal tar pitches possess great cost advantages,the strategy of using WS-CTPs as a carbon source to cover the metal oxides is a competitive way to expand the application of metal oxides in the fabrication of electrodes of LIBs.

Separation of Acearylenes from High-Temperature Coal Tar

High-temperature coal tar was extracted with petroleum ether(PE) under ultrasonic irradiation and the extracts were analyzed with gas chromatograph/mass spectrometer.The acearylene fractions including acenaphthylene,aceanthrylene and cyclopentapyrene were enriched together and named E,which was then transferred to a cartridge in Isolera-One flash chromatography.Three groups of compounds were eluted out with ethyl acetate/PE mixed solvent(volume ratio 1:9) and named E 1,E 2 and E 3 according to their main components.Acenaphthylene accounted for 78.2% in E 1,aceanthrylene 71.6% in E 2 and cyclopentapyrene 75.9% in E 3,respectively.The three groups of acearylenes were purified by Sephadex LH-20 column chromatography with ethanol/cyclohexane mixed solvent(volume ratio 1:4),and then confirmed with nuclear magnetic resonance spectrometer.This method indicates that flash chromatography has a good effect on separating the compounds with a similar structure after extraction under ultrasonic irradiation.