Die design and process optimization of die cast V6 engine blocks

The use of aluminum, particularly for engine blocks, has grown considerably in the past ten years, and continues to rise in the automotive industry. In order to enhance the quality and engineering functionality of die cast engine blocks, die design and processes have to be optimized. In this study, a computer simulation software, MAGMAsoft, as an advanced tool for optimizing die design and casting process, was employed to virtually visualize cavity filling and patterns of a V6 engine block. The original die design and process was simulated first to establish a baseline. A reality check was used to verify the predicted results. Then, the die modification with a different runner system was made by using a CAD software, Unigraphics (UG). The simulation on combinations of the modified die design and revised process was performed to examine the effect of die modification and process change on flow filling of V6 engine blocks. The simulated prediction indicates that the enhancement of cavity filling due to the die and process modification minimizes the occurrence of defects during casting, and consequently improves the quality of blocks. The results of mechanical testing show a significant increase in fatigue strengths, and a moderately improvement on tensile properties for the blocks die cast with the new die design and process in comparison with those produced by the original ones.

Die design for cold precision forging of bevel gear based on finite element method

The finite element analysis （FEA） software Ansys was employed to study the stress state of the dies of both plane and non-plane parting face structures with uniform interference and the die of plane parting face structure with non-uniform interference. Considering the symmetry of the die, a half gear tooth model of the two-ring assembled die with 2.5 GPa inner pressure was constructed. Four paths were defined to investigate the stress state at the bottom comer of the die where stress concentration was serious. FEA results show that the change of parting face from non-plane to plane can greatly reduce the stress at the teeth tips of the die so that the tip fracture is avoided. The interference structure of the die is the most important influencing factor for the stress concentration at the bottom comer. When non-uniform interference is adopted the first principal stress at the comer on the defined paths of the die is much lower than that with uniform interference. The bottom hole radius is another important influencing factor for the comer stress concentration. The first principal stress at the comer of the plane parting face die with non-uniform interference is reduced from 2.3 to 1.9 GPa when the hole radius increases from 12.5 to 16.0 mm. The optimization of the die structure increases the life of the die from 100 to 6 000 hits.

NUMERICAL DESIGN OF DIE LAND FOR SHAPE EXTRUSION

In the extrusion of shapes with flat faced die,the proper design of die land is of critical importance in avoiding the generations of geometry defects.A methodology for the design of die land,which consists of a simulation adjustment iteration,is proposed.The metal flow in extrusion is simulated by the three dimensional finite element method and the die land is adjusted according to the simulation result.Both the formulae for adjustment of the die land and the criterion for the judgment of proper die land are suggested.The extrusion of an L section shape is chosen as the computational example and the result is compared with the industrial design.

Analytical design of dies for the extrusion of sheets and annular parison

Based on the method of representative values and the flow pattern, that is, the position of the isobars parallel to the die orifice （PIPDO）, the design of dies for the sheet and annular parisons was improved in the present paper. Since this pattern includes the effects of the sloped manifold and the equations for designing the circular manifold are independent of operating conditions and the material, the distribution system of a die gives better uniformity of flow. In the previous study by Winter a defect was found, that is, the calculated position of the path of the island area lagged behind actual position. This defect was eliminated, and the modified equation was obtained. Another flow pattern, in which the pressure loss on all flow path is equal （PLFPE）, was introduced. The equivalency of the above two flow patterns was proved theoretically in this paper.

THEORETICAL ANALYSES ON DESIGN OF SHEAR EXTRUSION DIE

ＴＨＥＯＲＥＴＩＣＡＬＡＮＡＬＹＳＥＳＯＮＤＥＳＩＧＮＯＦＳＨＥＡＲＥＸＴＲＵＳＩＯＮＤＩＥ①ＹｕａｎＸｉＤｅｐａｒｔｍｅｎｔｏｆＭａｔｅｒｉａｌｓＳｃｉｅｎｃｅａｎｄＥｎｇｉｎｅｒｉｎｇ，ＣｅｎｔｒａｌＳｏｕｔｈＵｎｉｖｅｒｓｉｔｙｏｆＴｅｃｈｎｏ...

Heat Treat ment of Die and Mould Oriented Concurrent Design

Many disadvantages exist in the traditional die design method which belongs to serial pattern. It is well known that heat treatment is highly important to the dies. A new idea of concurrent design for heat treatment process of die and mould was developed in order to overcome the existent shortcomings of heat treatment process. Heat treatment CAD/CAE was integrated with concurrent circumstance and the relevant model was built. These investigations can remarkably improve efficiency, reduce cost and ensure quality of R and D for products.

Constrained Groove Pressing(CGP):Die Design,Material Processing and Mechanical Characterization

Constrained groove pressing(CGP)is a severe plastic deformation(SPD)technique used as a strengthening method for sheet metal.In the current work,an optimal/cost-saving design for CGP dies was attained using the stress analysis tool in SolidWorks Simulation Xpress wizard.This study examined low-cost and widely industrially applied aluminium materials,i.e.,pure 1050 Al and 5052 Al alloy.Each material was subjected to three passes of the CGP process using a 150 tons capacity press.For both materials,inter-pass annealing treatment was undertaken before the third pass.The effect of the number of CGP passes on the microstructure and tensile properties was studied after each pass.For CGPed pure 1050 Al with respect to the as-received material,the ultimate tensile strength(UTS),yield strength(YS)and YS/UTS ratio increased with an increasing number of CGP passes until the second pass,while elongation decreased with the number of passes.For CGPed 5052 Al alloy,the UTS and YS increased after the first pass and then decreased after the second pass.Variations in the elongation and YS/UTS ratio of 5052 Al alloy after the CGP process were insignificant.After inter-pass annealing and applying the third CGP pass,the strength of pure 1050 Al decreased,and that of 5052 Al alloy increased,which was attributed to the influence of composition on their structures.The strength-ductility balance decreased with an increasing number of CGP passes in both materials.

Effects of runner design and pressurization on the microstructure of a high-pressure die cast Mg-3.0Nd-0.3Zn-0.6Zr alloy

To clarify the relationship between externally solidified crystals(ESCs)and other defects,e.g.,defect bands and pores,two dimensional(2D)and three dimensional(3D)characterization methods were adopted to analyze castings produced using a modified ingate system equipped with and without an ESC collector.The reduction of ESCs strongly reduced defect band width and shrinkage pore quantity.By reducing the quantity and size of ESCs,net-shrinkage pores were transformed into isolated island-shrinkage pores.We determined via statistical analysis that the mechanical properties of high pressure die castings were strongly related to the size and fraction of the ESCs rather than porosity volume.The reduction of ESCs also caused tensile transgranular fracture modes to transform into intergranular fracture modes.Additionally,casting pressurization strongly reduced pore morphology,volume,and size.

An Integrated Die Casting Design System

Die casting process is one of the prime options for m anufacturing precisely dimensioned, sharply defined metal parts. The design of d ie casting dies comprises several stages and entails a large amount of time. Tra ditionally, the different stages of the die design were not integrated but exist as separate entities. Moreover, recurring modifications or even redesigns are r equired due to the complexity in achieving an accurate initial die design. As a result, die design is usually time-consuming and costly with respect to resourc es. The die casting industry will greatly benefit if proper application software are developed that integrates the different die design stages and allows editin g of die design as and when needed. Hence it is imperative to create an integrat ed die design system that shortens the die design time. This paper presents a research that establishes a prototype of an integrated die design system. It is developed using the commercial SolidWorks CAD system and n amed DiWorks. The aim of building the system on a commercial CAD system is to ut ilise the resources and features of the CAD system to speed up the die design pr ocess. DiWorks consists of six distinct modules: Project Manager, Cavity Insert Builder, Gating System Constructor, Die Base Designer, Ejector System Constructo r and Standard Components Library. Through these six modules, the die designer c an create a complete die casting die beginning from a product part model. It is a user-friendly system that allows both experienced and novice die designers to easily accomplish the task of die design. The practical goal of this research is twofold: to develop a system that integra tes the die design process and at the same time facilitates the editing of d ie design during or after the course of the design process. The research approac h includes (i) parametric design, (ii) feature-based design (iii) system modeli ng and implementation. Parametric design deals with variable dimensions as contr ol parameters, and it is an efficient tool for creating models based on paramete rs. Parametric design not only increases the design efficiency, but also makes t he updates and modifications of existing designs easier and faster, since these can be achieved by changing the parameters of the parametric model. Feature-bas ed design is used to design a product with features that are functionally define d by attributes and are geometrically represented by a set of parameters. The re sults of this research will aid the automation of the die design process, thus i mproving the efficiency and quality of, and reducing the cost of die design.

USING LOGIC COMPONENTS FOR CONCEPTUAL DIE DESIGN

Logic components are used to support the conceptual design Taking the stamping die structure as the research object,several logic components are defined for the conceptual die construction design A new method logic assembly modeling is presented to satisfy the characteristic of the top down die design process Representing shapes and spatial relations in logic can provide a natural,intuitive method of developing complete computer systems for reasoning about die construction design at the conceptual stage This method can reflect the designer's thought clearly and provide the designer with a test bed for generating alternatives and performing reasoning work at the conceptual die design stage

Stress Analysis and Optimum Design of PDC Die for Offshore Drilling Engineering

The maximum internal tangential stress is a critical parameter for the design of the PDC （polycrystalline diamond compact） die that has been widely applied to offshore oil drilling. A new simple equation for the calculation of the stress is developed, and verified by the test data from Kingdream Corp. of China, the largest bit Company in China. An opti- mum method for the design of the PDC die is presented and demonstrated in detail, and software for the design and FEM analysis of the die is developed on the basis of the method. This software has been used in oil industry in recent years.

New trends in cold-chamber die casting machine design

Larger and larger proportions of aluminium castings,especially those produced by the die casting process,can be observed during recent years in the automotive industry,house-hold articles and others.In case of the automotive industry,apart from the traditional elements produced by the die pressure method such as engine blocks or crank shaft bedplates,aluminium is displacing steel from structural parts of cars('body in white').The current state and development directions of the structural solutions of cold-chamber die castings are analysed in this paper.These solutions drive the prospective development of these machines and die casting technology.The focus is mainly on essential functional systems such as:hydraulic drives of closing and locking units,as well as pressing in die machines of known companies present on the European market.

OPTIMUMDESIGNOFSTREAMLINEDEXTRUSIONDIESBASEDONUPPERBOUNDMETHODANALYSIS

A more universal and flexible method of constructing the streamlined die surfaces is presented. The streamlined die surfaces are interpolated by the arbitrarily cross sectional shapes of the die entrance and exit. The boundaries of the die entrance and exit are represented by Ferguson curves with tension parameters. By adjusting the tension parameter, the cross sectional shapes of the die entrance and exit with line segments can be accurately constructed. The upper bound method is used to analyze the procedure of extrusion, the pseudo independent parameters in kinematically admissible velocity and die surface are computed by minimizing the extrusion load, so the optimum die surface is obtained. The effects of frictional condition, die length, area reduction and product shaped complexity are discussed in relation to the extrusion load.

基于“PBL+云平台”的《冲压工艺与模具设计》课程改革探索与实践

模具制造技术专业的核心课程《冲压工艺与模具设计》正受到授课内容布置、教学实施、成绩评估等方面的限制,随着互联网技术与教育的融合,以平台规划、学情分析及教学评价为突破口,基于云平台建设了《冲压工艺与模具设计》在线课程,并以PBL模式实施教学,实现了资源与知识点匹配衔接,形成了既能合理运用资源实施多种方法授课,又会创作资源的创新型课程教学团队,助推人才培养质量。

基于“互联网+教育”的模具设计与制造专业课程教学改革的探索

针对模具设计与制造专业课程理论逻辑性强、过于抽象的教学难点,以互联网为基础,利用网络教学平台,通过线上、线下混合的教学方法及教学反思,不断推动“互联网+教育”在模具设计与制造专业课程中的应用,促进专业课程教学改革,以提高学生学习的自主性,激发学生学习的热情,提高教学质量。

聚合物三腔微管挤出口模结构对胀大变形的影响

聚合物熔体的模内流动状态与模外胀大变形直接影响微挤出制品的成型质量。文中基于Carreau模型,采用数值模拟方法,研究了聚合物三腔微管挤出过程中口模壁厚差与空心度结构特征对胀大变形行为的影响。结果表明,影响挤出胀大变形程度的关键因素是口模出口附近的轴向速度分布;内外壁厚差会导致较大壁厚位置处对应的型坯厚度增大,而较小壁厚位置处的型坯厚度减小,壁厚差变化对薄壁区域壁厚变形影响较大,达到91.4%;空心度减小能提升口模出口附近轴向速度分布均匀性,减小了70.1%的变形程度;基于胀大变形规律逆向补偿设计了口模形状与尺寸,明显改善了制品成型质量。研究结果对聚合物多腔微管的口模结构优化设计具有理论意义与工程应用价值。

基于真空压铸技术的机壳压铸模设计

通过对机壳压铸件的结构工艺分析,介绍了真空压铸技术下模具的浇注系统、成型零件、侧向分型与抽芯机构、推出机构、溢流与排气系统、温度控制系统等机构的设计要点,相比普通压铸的模具,能有效减低压铸原材料的损耗,提升压铸件质量,为类似模具的设计提供一定的参考借鉴。

高速钢桶焊缝机电机座支撑脚复合模设计

针对高速钢桶焊缝机电机座支撑脚使用2 mm厚的SECC板料进行中小批量冲压成形的要求,设计了3副模具用于制件的4道工序成形。冲孔落料和修边压印采用倒装式复合模结构、切分模和弯曲模采用正装结构,且切分模和弯曲模集成在1副模具内。弯曲模中设计了凸模驱动的双滑块内收弯曲成形机构,该机构在制件弯曲壁的两侧都使用滑块进行夹紧驱动弯曲,能有效防止弯曲回弹,保证了制件的弯曲成形尺寸。模具结构简单实用,成形工艺设计合理,实现了制件的自动化生产。

模具设计与制造专业班会内容与PTS人生技能课程相融合的研究

模具设计与制造专业学生的班会内容与专业拓展课《PTS人生技能》的内容相融合,先分析模具设计与制造专业的培养目标,阐述拓展课的8个模块,并以“理解和管理情绪模块”为例进行了主题班会的实施过程的介绍。班会内容与PTS人生技能课的融合是一种有益的尝试,班会中应用了课程的“演、思、说、用”4个环节。以学生为中心的理念,经验学习圈理论。让学生在班会中学习和应用人生技能,提升了个人综合素质,为学生的全面发展提供有力支持。

汽车车灯支架压铸工艺CAE分析及模具设计

分析了汽车车灯支架的结构特点,进行了压铸工艺设计,并应用ProCAST软件对该铝合金压铸件的充型过程、压铸模具热平衡和温度场进行了数值模拟分析,预测缺陷产生的位置及原因,根据预测结果对模具结构进行了优化。实际生产表明,采用优化后的模具设计方案提升了铸件质量。