Test Research on the Knock of a Common-Rail Diesel Engine Fueled with Diesel-Methanol Dual-Fuel

Experiments were conducted on a diesel-methanol dual-fuel(DMDF)engine modified by a six-cylinder,turbocharged,inter-cooled diesel engine.According to the number of diesel injection,the experiments are divided to two parts:the single injectionmode and double injectionmode.The results show that,at the double injectionmode,themaximumof pressure rise rate is small and the engine runs smoothly,however,knock still occurswhen the cocombustion ratio(CCR)is big enough.Under knock status,the power density of the block vibration concentrating at some special frequencies rises dramatically,and the special frequency of single injection mode(about 4.1 kHz)is lower than that of double injection mode(7–9 kHz).The cylinder pressure oscillations of knock status are very different fromthe non-knock status.Under knock status,cylinder pressure oscillations become more concentrated and fiercer at some special frequencies,and the same as the block vibration.The special frequency of single injection mode(3–6 kHz)is lower than that of double injection mode(above 9 kHz).

Frequency compensation control method for opposedpiston two-stroke folded-cranktrain engine's common rail system by loop-shaping theory

A frequency compensation control method for the opposed-piston two-stroke folded-cranktrain（ OPFC） diesel engine＇s common rail system is presented as a result of the study of the loop-shaping theory. A common rail working process and the classical frequency control theory are combined to construct a frequency restriction of common rail pressure. A frequency compensator is utilized to improve the robustness of multiplicative perturbations and disturbance. The loop-shaping method has been applied to design the common rail pressure controller of the OPFC diesel engine. Simulation and bench test results show that in the condition of perturbation that comes from the effect of injection,multi-injection,fuel pumping of a pre-cylinder,and instantaneous pressure fluctuation,the controller indicates high precision. Compared with the original controller,this method improves the control precision by 67. 3%.

MAN L48/60CR型柴油机高压油泵故障分析

文章针对MAN L48/60CR型柴油机常见的高压油泵故障,从燃油供油系统、安全阀、燃油喷射控制单元、节流阀、高压油泵柱塞等方面分析可能出现的原因,深入讨论了高压油泵柱塞磨损故障机理,提出了高压油泵使用建议,为该机型柴油机管理提供一定的使用参考。

利用CRS-OIS实现噪声压制与数据插值

CRS-OIS是一种以输出道成像方式实现的共反射面元叠加成像方法,不仅能够输出一张高质量的叠加剖面,也能够得到高质量的叠前道集.将这一特色用于陆地二维地震数据处理的噪音压制与数据插值计算,理论与实际数据计算证实了该方法的有效性,体现出很好的应用潜力.

实现最佳零炮检距地震照明成像——CRS叠加之几何阐述

零炮检距剖面是地震反射成像过程中重要的中间成果 ,常规处理中的共中心点 (CMP)叠加的目的正在于此。当地层倾斜时 ,CMP道集发生反射点弥散 ,CMP叠加无法得到正确的零炮检距 (ZO)剖面。在这种情形下 ,只有实施NMO/DMO叠加或沿着共反射点 (CRP)轨迹进行叠加才能达到偏移到零炮检距 (MZO)的目的。根据共反射面元 (CRS)叠加理论 ,CRS叠加面是反射点附近一个邻域内CRP轨迹的集合 ,所以沿CRS叠加面应能得到最好的零炮检距剖面。以几何描述的方式 ,在常速介质假设下通过图示定性描述CRP与CRS叠加之间 ,NMO/DMO叠加、叠前深度偏移 (PreSDM )与CRS叠加之间的区别与联系。

CRS叠加的研究现状及发展趋势

在常规处理中,复杂地质条件下的时间域成像和叠后偏移的效果不是很理想。为此,提出了一些新的时间域成像技术和叠前偏移方法,CRS(common reflection surface,共反射面元)叠加便是其中的一种。CRS叠加是一种可以直接由多次覆盖反射数据得到零炮检距(ZO)剖面而不依赖于速度信息的叠加方法。二维和三维CRS叠加不仅能够改进模拟ZO剖面,提高深层的信噪比,而且给出了可用于反演速度场的多参数剖面。模型数据的试算和实际资料的处理验证了方法的有效性和实用性。基于起伏地表的CRS叠加不需要先对原始数据做静校正,而且得到叠加结果后可以很容易地实现基准面重建。另外,利用CRS得出的出射角及波前曲率信息可以更好地实现偏移速度建模,这也是今后CRS研究的一个重点。

中大型16V柴油机用FCRS2-LE型共轨系统的开发和应用

从中大型共轨系统的原理和基本构成出发,介绍了16V柴油机用FCRS2-LE型共轨系统的总体布置方案,详细介绍了共轨供油泵、喷油器、共轨管和电控单元4大系统的结构方案、技术特点、性能指标等内容,样品配机性能试验结果表明,这种共轨系统的技术方案可行。

Influence of eddy current on transient characteristics of common rail injector solenoid valve

Influence of eddy current on transient characteristics of common rail injector solenoid valve was studied in this paper. Experimental investigations of drive current and power source volt- age of both drive current ascending and descending process were conducted on a common rail injec- tor solenoid valve. A new discretizing calculation method of solenoid valve flux linkage was put for- ward for the first time based on the experimental results and drive circuit principle, and flux linkage of both drive current ascending and descending process were evaluated. New inductance calculation methods for drive current ascending and descending process respectively were also presented. Influ- ence of parasitic inductance was evaluated. Results indicate that the air gap, under which the transi- ent flux linkage of the solenoid valve is the biggest, varies with drive current due to eddy current. Flux linkage of drive current descending process is bigger than that of drive current ascending process under the same drive current and the same air gap width. Eddy current can reduce the delay between the time that drive current begins to descend and the time that armature begins to move downward. Inductance of drive current descending process is bigger than that of drive current as- cending process over larger scope of drive current, but the difference becomes smaller with the in- creasing of air gap width. The differences of both flux linkage and inductance between drive current ascending and descending process are caused by the eddy current in core and armature materials.

STRATEGY FOR DIESEL ROTARY ENGINE WITH COMMON RAIL INJECTION SYSTEM

A direct injection low compression ratios diesel rotary engine is designed and studied to find the appropriate application of the electronic controlled high pressure common rail injection system. Current development focuses on the applied fuel injection and ignition strategies, especially concerning the combustion configurations of injectors, ignition source, and combustion chamber. The prototype engine, equipped with Bosch common rail system and high performance electronic control unit （ECU）, is designed correspondingly. Studies show that the integration of a common rail injection system and the main and pilot duel injectors configurations, assisted with glow plug ignition device and flexible ECU, represents a promising approach to improve the potential of the low compression ratios diesel rotary engine. Currently the engine can run at 6 kr · min^-1 steadily and the power is about 68 kW/（4 kr ·min^- 1）.

Elimination of Fuel Pressure Fluctuation and Multi-injection Fuel Mass Deviation of High Pressure Common-rail Fuel Injection System

The influence of fuel pressure fluctuation on multi-injection fuel mass deviation has been studied a lot,but the fuel pressure fluctuation at injector inlet is still not eliminated efficiently.In this paper,a new type of hydraulic filter consisting of a damping hole and a chamber is developed for elimination of fuel pressure fluctuation and multi-injection fuel mass deviation.Linear model of the improved high pressure common-rail system（HPCRS）including injector,the pipe connecting common-rail with injector and the hydraulic filter is built.Fuel pressure fluctuation at injector inlet,on which frequency domain analysis is conducted through fast Fourier transformation,is acquired at different target pressure and different damping hole diameter experimentally.The linear model is validated and can predict the natural frequencies of the system.Influence of damping hole diameter on fuel pressure fluctuation is analyzed qualitatively based on the linear model,and it can be inferred that an optimal diameter of the damping hole for elimination of fuel pressure fluctuation exists.Fuel pressure fluctuation and fuel mass deviation under different damping hole diameters are measured experimentally,and it is testified that the amplitude of both fuel pressure fluctuation and fuel mass deviation decreases first and then increases with the increasing of damping hole diameter.The amplitude of main injection fuel mass deviation can be reduced by 73%at most under pilot-main injection mode,and the amplitude of post injection fuel mass deviation can be reduced by 92%at most under main-post injection mode.Fuel mass of a single injection increases with the increasing of the damping hole diameter.The hydraulic filter proposed by this research can be potentially used to eliminate fuel pressure fluctuation at injector inlet and improve the stability of HPCRS fuel injection.

An experimental study on RP-3 jet fuel injection on a common rail injection system

RP-3 jet fuel could be an alternative fuel for diesel engines.In this study,the injection characteristics of RP-3jet fuel under single and split injection strategies were investigated and compared with diesel fuel.The experimental results indicate that RP-3 jet fuel has slightly shorter injection delay time than diesel fuel,but this difference is negligible in actual engine operations.Further,although the lower density and viscosity of RP-3 jet fuel lead to higher volumetric injection rates and cycle-based injection quantities,the cycle-based injection mass and the mass injection rates at the stable injection stage of RP-3 jet fuel are close to or slightly lower than those of diesel fuel.Based on these experimental observations,it could be concluded that fuel physical properties are the secondary factor influencing the injection characteristics in both single and split injection strategies,as RP-3 jet fuel and diesel fuel are taken for comparison.

Characteristics of Diesel/N-Butanol Blend on a Common Rail Diesel Engine with Exhaust Gas Recirculation

20%n-butanol is blended in diesel by volume(noted as D80B20)and experiment has been carried out to study the effect on the combustion and emission characteristics based on a common rail diesel engine with exhaust gas recirculation(EGR)system.The results reveal thatD80B20 has longer ignition delay,shorter combustion duration and higher maximumin-cylinder temperature than pure diesel(noted as D100).Further,the number concentration and volume concentration of ultrafine particles decrease significantly while NO_(X) emissions increase a little with the addition of n-butanol.When the exhaust gas is induced into cylinder,NO_(X) emissions significantly decrease and ultrafine particles emissions increase.The number geometric mean diameters and volume geometricmean diameters of ultrafine particles increase withEGR ratio.Compared toD100 without EGR,D80B20 with 20%EGR ratio can reduce both NO_(X) and ultrafine particles emissions at 0.14MPa BMEP and 0.56MPa BMEP.

引燃柴油量对双燃料发动机循环变动的影响

为了降低重型高压共轨柴油机燃用LNG-柴油的燃烧循环变动,优化引燃柴油量控制,通过双燃料发动机试验台架,研究了在最大转矩转速1600r/min,功率输出为73kW工况下,随引燃柴油喷油量的增加,峰值压力、峰值压力升高率、平均指示压力循环变动的变化趋势。研究结果表明,随引燃柴油量的增加,双燃料发动机的峰值压力、峰值压力升高率和平均指示压力的循环变动趋势相同,它们的均值均增大,标准差减小,循环分布集中,循环变动系数降低。在不导致爆震燃烧的前提下,适当增大引燃柴油量,能够改善双燃料发动机的燃烧稳定性。

高压共轨柴油机国产芯片控制系统研究

针对现有高压共轨柴油机电控单元高度依赖进口芯片、自主不足的问题,提出了基于全国产芯片的高压共轨柴油机电控单元方案。所设计的国产控制单元选用兆易创新的GD32F450芯片为控制核心,承担发动机数据采样、处理、存储与控制任务。首先,采用Boost升压电路提供喷油器峰值电流,利用分立器件设计双边驱动与电流反馈电路,在不依赖进口专用芯片的条件下,对喷油器驱动电流进行闭环控制;然后,基于FreeRTOS操作系统,开发高压共轨柴油机底层驱动软件,实现对不同任务调度周期的精准控制;最后,对所设计的电控单元进行了实验验证。结果表明,所设计的国产高压共轨柴油机电控单元功能齐全、工作稳定,双边驱动电路典型峰值电流为22 A,维持电流为10 A,最小喷射间隔时间为200μs,多次喷射性能与Bosch系统相当。发动机不同转速条件下任务调度周期精准、实时性好,研究证实了高压共轨柴油机电控单元全国产化方案的可行性,对推动发动机电控技术自主可控提供了有益参考。

喷油器柱塞副动态泄漏及特性

为了研究高压共轨喷油器柱塞副的动态泄漏特性,建立了柱塞副间隙燃油流动的数学模型,通过有限差分法对数学模型进行数值计算,研究了不同轨压下柱塞副燃油的平均动态泄漏率的变化趋势,与试验值进行对比,验证该数学模型的有效性,并分析了轨压、进口燃油温度、柱塞最大升程和喷射脉宽四种因素对柱塞副动态泄漏量的影响及在不同柱塞速度下,油膜压力、厚度和温度参数的变化趋势。结果表明,在一个喷油循环内,动态泄漏率的变化曲线与控制腔油压变化曲线相似,平均动态泄漏率随着喷油器的轨压、入口燃油温度和柱塞最大升程的增加而增加,但随着喷射脉宽的增加而减小;随着柱塞速度由正速度到负速度的过程,油膜的厚度逐渐变薄,油膜的温度整体上升,油膜的压力变小。

电控高压共轨喷油系统结构参数对轨内压力波动仿真分析

采用GT软件建立电控高压共轨燃油喷射系统模型,并利用构建的仿真模型研究高压油泵的进油阀组件、排油阀组件以及活塞凸轮组件,其三个主要部分的结构参数变化对共轨管中压力波动的影响。通过研究可知高压泵在实际工作时所承受的压力波与活塞的状态有直接关系,且活塞状态包括其质量、长度、直径、容积等。为了更好地研究进排油阀对压力波动之间的关系,选用8组参数进行实验研究并验证进排油阀体直径、质量、弹簧预紧力、弹簧刚度的变化与压力波动之间的相互影响作用,进而通过对比选取最佳阀体。通过仿真分析可知,共轨喷油系统压力波动程度会受到系统结构参数的影响,并可以为系统的优化设计提供参考依据。

博世共轨压力泄压阀打开故障解析

文章主要对泄压阀的结构原理、故障发生机理进行系统介绍,并结合故障诊断与排除思路进行说明,以期能够为维修人员提供一些启发和帮助。

汽车发动机高压共轨系统轨压特性分析与优化

基于关键零/部件参数,建立了汽车发动机高压共轨喷射系统的数学模型,使用AMESim软件进行仿真模拟,并通过试验分析验证了该仿真模型的准确性。通过对系统轨压波动和压力特性进行仿真分析,得出共轨管长度、内径和高压油管内径是影响系统轨压特性的重要参数。针对原始共轨管和高压油管模型,利用响应曲面法对共轨管和高压油管参数进行优化分析,并得出以平均轨压设定值为目标的共轨管和高压油管的最佳结构参数。经过优化后,汽车发动机高压共轨喷射系统的平均轨压提高了0.65%,整体轨压波动平均值降低了79.48%,单次喷射过程中轨压波动平均值降低了27.89%,平均喷油压力提高了0.63%,其喷油特性得到明显的改善。

非道路柴油机冷却水套流动传热分析与优化

冷却水套作为柴油机的核心结构,其流动与传热特性直接影响着柴油机的可靠性和使用寿命。以某两缸高压共轨柴油机为研究对象,为了解该发动机冷却水套流动与传热性能,以水套速度场、温度场、换热系数等空间分布参数为判据,重点对冷却水套关键区域的流动和传热特性进行分析,同时提出优化方案。仿真结果表明:发动机整体冷却液流动性差,平均流速低于0.5m/s,缸体进气侧冷却水套上部出现了流动死区;通过对冷却系统性能参数和冷却水套结构进行优化,冷却水套进出口压力损失减小,整体冷却液平均流速较原方案提高了173.91%,整体平均换热系数较原方案提高了41.93%,整体冷却水套流动均匀性得到改善。

基于cRIO控制器的高压共轨柴油机ECU硬件在环仿真系统设计

为测试和验证高压共轨柴油机电控单元的控制策略,设计了一套基于cRIO控制器的ECU硬件在环仿真系统.系统采集高压共轨柴油机的执行机构信号,用DMA方式将数据送至cRIO0控制器,经燃油喷射和排气阀驱动数学模型计算,输出控制模拟曲轴电机转速和保证ECU正常工作的信号.系统还在NIPXI平台设计了ECU监测记录模块.系统的设计可节省高压共轨柴油机ECU测试试验费用和缩短开发优化周期.