Influence of Non-smooth Surface on Tribological Properties of Glass Fiber-epoxy Resin Composite Sliding against Stainless Steel under Natural Seawater Lubrication

With the development of bionics, the bionic non-smooth surfaces are introduced to the field of tribology. Although non-smooth surface has been studied widely, the studies of non-smooth surface under the natural seawater lubrication are still very fewer, especially experimental research. The influences of smooth and non-smooth surface on the frictional properties of the glass fiber-epoxy resin composite（GF/EPR） coupled with stainless steel 316 L are investigated under natural seawater lubrication in this paper. The tested non-smooth surfaces include the surfaces with semi-spherical pits, the conical pits, the cone-cylinder combined pits, the cylindrical pits and through holes. The friction and wear tests are performed using a ring-on-disc test rig under 60 N load and 1000 r/min rotational speed. The tests results show that GF/EPR with bionic non-smooth surface has quite lower friction coefficient and better wear resistance than GF/EPR with smooth surface without pits. The average friction coefficient of GF/EPR with semi-spherical pits is 0.088, which shows the largest reduction is approximately 63.18% of GF/EPR with smooth surface. In addition, the wear debris on the worn surfaces of GF/EPR are observed by a confocal scanning laser microscope. It is shown that the primary wear mechanism is the abrasive wear. The research results provide some design parameters for non-smooth surface, and the experiment results can serve as a beneficial supplement to non-smooth surface study.

Experimental Study on Influence of Dimples on Lubrication Performance of Glass Fiber-epoxy Resin Composite under Natural Seawater Lubrication

Bionic non-smooth surface is widely applied in metal and ceramics materials. In order to introduce this technology to high pressure seawater pump, the influence of bionic non-smooth surface on the engineering plastics used in pump should be investigated. The comparative tests are carried out with a ring-on-disc configuration under 800, 1000, 1200 and 1400 r/min in order to research the influence of the bionic non-smooth surface on glass fiber-epoxy resin composite（GF/EPR） under natural seawater lubrication. The disc surfaces are textured with five kinds of pits, which are semi-spherical, conical, cone-cylinder combined, cylindrical pits and through holes, respectively. A smooth surface is tested as reference. The results show that the lubrication performance of dimpled GF/EPR sample is much better than that of the smooth sample under all rotational speeds. The semi-spherical pits surface has more obvious friction reduction than the others, which shows that the least reduction is approximately 43.29% of smooth surface under 1200 r/rain. However, the wear level is only marginally influenced by dimples. The surface morphology investigations disclose severe modifications caused by abrasive wear primarily. The results are helpful to vary friction properties of GF/EPR by non-smooth surface, or provide references to the design of non-smooth surfaces under certain condition.

Determination of Water Diffusion Coefficients and Dynamics in Adhesive/Carbon Fiber Reinforced Epoxy Resin Composite Joints

To determinate the water diffusion coefficients and dynamics in adhesive/carben fiber reinforced epoxy resin composite joints, energy dispersive X-ray spectroscopy analysis（EDX） is used to establish the content change of oxy- gen in the adhesive in adhesive/carbon fther reinforced epoxy resin composite joints. As water is made up of oxygen and hydrogen, the water diffusion coefficients and dynamics in adhesive/carben fiber reinforced epoxy resin composite joints can be obtained from the change in the content of oxygen in the adhesive during humidity aging, via EDX analy-sis. The authors have calculated the water diffusion coefficients and dynamics in the adhesive/carbon fiber reinforced epoxy resin composite joints with the aid of beth energy dispersive X-ray spectroscopy and elemental analysis. The de- termined results with EDX analysis are almost the same as those determined with elemental analysis and the results al- so show that the durability of the adhesive/carbon fther reinforced epoxy resin composite joints subjected to silane cou- pling agent treatment is better than those subjected to sand paper burnishing treatment and chemical oxidation treat- ment.

Epoxy Resin/Nano Ni@C Composites Exhibiting NTC Effect with Tunable Resistivity

Epoxy resin/Ni@C nanoparticle composites with aligned microstructure were prepared by using a procedure of magnetic field assisted curing. The results show that the resistivity of composites exhibits negative temperature coefficient （NTC） effect above room temperature, and can be adjusted by varying the content filler and the magnitude of magnetic field applied. Hill＇s quantum tunneling model was modified to understand the electrical conduction mechanism in the composites. It shows that the NTC effect ascribes to the dominant thermal activated tunneling transport of electron across adjacent nanoparticles, as well as the low thermal expansivity of epoxy resin matrix.

Research on properties of hollow glass microspheres/epoxy resin composites applied in deep rock in-situ temperature-preserved coring

Deep petroleum resources are in a high-temperature environment.However,the traditional deep rock coring method has no temperature preserved measures and ignores the effect of temperature on rock porosity and permeability,which will lead to the distortion of the petroleum resources reserves assessment.Therefore,the hollow glass microspheres/epoxy resin(HGM/EP)composites were innovatively proposed as temperature preserved materials for in-situ temperature-preserved coring(ITP-Coring),and the physical,mechanical,and temperature preserved properties were evaluated.The results indicated that:As the HGM content increased,the density and mechanical properties of the composites gradually decreased,while the water absorption was deficient without hydrostatic pressure.For composites with 50 vol%HGM,when the hydrostatic pressure reached 60 MPa,the water absorption was above 30.19%,and the physical and mechanical properties of composites were weakened.When the hydrostatic pressure was lower than 40 MPa,the mechanical properties and thermal conductivity of composites were almost unchanged.Therefore,the composites with 50 vol%HGM can be used for ITPCoring operations in deep environments with the highest hydrostatic pressure of 40 MPa.Finally,to further understand the temperature preserved performance of composites in practical applications,the temperature preserved properties were measured.An unsteady-state heat transfer model was established based on the test results,then the theoretical change of the core temperature during the coring process was obtained.The above tests results can provide a research basis for deep rock in-situ temperature preserved corer and support accurate assessment of deep petroleum reserves.

The application of nanotechnology in the improvement of dental composite resins

In this paper, nanotechnology for the improvement of dental composite resins has been reviewed in the background of the existing shortcomings, focusing on the improvement for polymerization shrinkage, anti-bacterial properties and mechanical properties of composite resins. The results show that the use of nanotechnology and nano materials can be an effective method to improve the performance of dental composite resins in a various ways. At last, the paper also discusses the perspective about the dental composite resins.

Fluxing Agents on Ceramification of Composites of MgO-Al2O3-SiO2/Boron Phenolic Resin

Fluxing agents of zinc borate, antimony oxide, galss frit A and glass frit B, with different melting or softening point temperatures, were added into MgO-Al_2O_3-SiO_2/boron phenol formaldehyde resin（MAS/BPF） composites to lower the formation temperature of eutectic liquid phase and promote the ceramification of ceramifiable composites. The effects of fluxing agents on the thermogravimetric properties, phase evolution, and microstructure evolution of MAS/BPF composites were characterized by TG-DSC, XRD and SEM analyses. The results reveal that the addition of a fluxing agent highly reduces the decomposition rate of MAS/BPF composites. Fluxing agents lower the formation temperatures of liquid phases of ceramifiable MAS/BPF composites obviously, and then promote the ceramification and densification process. The final residues of composites are ceramic surrounded by large amount of glass phases.

Effect of zeta potentials on bovine serum albumin adsorption on crown composite resin surfaces <i>in vitro</i>

We previously studied the mechanism underlying the adsorption of oral bacteria on the surfaces of dental prosthetic materials such as ceramics and resins in vitro. The aim of the present study was to examine bovine serum albumin (BSA) adsorption on crown composite resin surfaces by means of zeta potential. We measured the zeta potentials of resins alone, BSA alone, and resins after BSA adsorption. Eight resins were pulverized into powders (300 - 1000 nm). All experiments were conducted in 10 mM sodium chloride solution (pH 6.5). BSA was dissolved in 10 mM NaCl with a concentration of 2.0 × 10-5 mol/l. An adsorption assay was performed for one hour at 37°C under continuous rotation (6 rpm). The zeta potentials of both resins and BSA were negative, with BSA itself less negative than the resins themselves as an absolute value (p < 0.0001). The zeta potentials of seven resin surfaces after BSA adsorption were significantly less negative than were those of the resins without BSA adsorption (p < 0.0001). Eight resins were divided into two classes based on the size of the surface potential difference between each resin and the BSA. The difference in surface potential between the resins and the BSA were small, leading to the theory that particles with identical charges repulse each other, and the amounts of adsorbed BSA on these resins might be less. On the other, when the differences between the other resins and BSA are large, so that the repulsive force between two nonidentical particles becomes zero and an attractive force might be generated, then more BSA might be adsorbed on those resins. Therefore, the zeta potentials were affected by BSA adsorption and became less negative. These results suggested that electrostatic interactions play an important role in the adsorption of BSA on resin surfaces.

Effect of Natural Fiber Reinforced Polypropylene Composite Using Resin Impregnation

In this paper, we deals with mechanical performance of resin impregnation with natural fiber and fiber reinforced composites. The effect of the addition of a rein impregnation process on static strength of the injection molded composites was investigated by carrying out tensile and banding tests, followed by Scanning electron microscopy (SEM) observation of fiber surface and fracture surface of composites. The tensile strength of natural fiber and natural fiber reinforced composites with resin impregnation method increases with Polyvinyl alcohol (PVA) impregnation. In addition, Phenol resin impregnation recovers fiber tensile strength after alkali treatment. Resin impregnation causes decrease in contact surface area;however, it does not cause decrease in mechanical properties. Our results suggest that the using rein impregnation method has better effect on the mechanical properties of natural fiber reinforced Polypropylene (PP) composites.

Synthesis of Antistatic Composite Based on Reaction Flame Retarding Unsaturated Polyester Resin

The synthesis of reaction flame retarding unsaturated polyester resin and the flame retarding mechanism are investigated.By taking the synthesis flame retarding unsaturated polyester resin as a base material,glass fibers as reinforced material,under the condition of adding graphite or carbon black respectively,the composites were manufactured.The flame retarding and antistatic properties are also studied.In the experiment,bromide-bearing flame retarding resin decomposed under a high temperature.Compound HBr was set out and retarded or stopped the flame.High concentration of HBr gas wall was formed between gas and solid phrases,which decreased flame.The results show that antistatic property of carbon black is higher than that of graphite.Adding a threshed value of 1% carbon black into composite,the antistatic property is at its highest value.

Synergistic regulation of current-carrying wear performance of resin matrix carbon brush composites with tungsten copper composite powder

Resin matrix carbon brush composites(RMCBCs)are critical materials for high-powered electric tools.However,effectively improving their wear resistance and heat dissipation remains a challenge.RMCBCs prepared with flake graphite powders that were evenly loaded with tungsten copper composite powder(RMCBCs-W@Cu)exhibited a low wear rate of 1.63 mm^(3)/h,exhibiting 48.6%reduction in the wear rate relative to RCMBCs without additives(RMCBCs-0).In addition,RMCBCs-W@Cu achieved a low friction coefficient of 0.243 and low electric spark grade.These findings indicate that tungsten copper composite powders provide particle reinforcement and generate a gradation effect for the epoxy resin(i.e.,connecting phase)in RMCBCs,which weakens the wear of RMCBCs caused by fatigue under a cyclic current-carrying wear.

Effect of volume fraction of ramie cloth on physical and mechanical properties of ramie cloth/UP resin composite

Ramie cloth/UP resin composite was formed at 0.2 MPa and cured at room temperature for 24 h and treated at 80℃for 2 h. The physical and mechanical properties of the composites with different volume fractions of ramie cloth were studied. The results show that, with the increase of the volume fraction of the ramie cloth, densities of the composites become greater and greater, though all lower than the theoretical values, the linear shrinkage during the formation decreases from 1.20% of the original UP resin to 0.18% of the composite with 30% of ramie cloth in volume, all the composites also absorb more water than UP resin casting, greater volume fraction of the fiber, more water will be absorbed, but the increase in water absorption becomes smaller and smaller with time. As regards some mechanical properties, the tensile strength, flexural strength, flexural modulus and impact strength are all improved when more ramie fiber is added. Compared with those of pure UP resin casting, the mechanical properties are increased by 93.93%, 76.20%, 190.18% and 227.26% respectively when the volume fraction of the ramie cloth in the composite is 30%. The differential scanning calorimetry results show that only one peak will appear for the sample without or with less ramie fiber while two peaks will appear when more ramie cloth is added.

Fracture and Tribological Evaluation of Dental Composite Resins Containing Pre-polymerized Particle Fillers

The fracture and tribological evaluation of dental composite resin containing pre-polymerized particle fillers were investigated. Composite resins, e.g. metafil, silux plus, heliomolar and palfique estelite were selected as specimens in order to evaluate the effects of pre-polymerized particle filler on the fracture and wear characteristics of composite resins. In the wear tests, a ball-on-flat wear test method was used. The friction coefficient of metafil was quite high. The wear resistance of silux plus and palfique estelite was better than that of metafil and heliomolar under the same experimental condition. The main wear mechanism of composite resins containing pre-polymerized particle fillers was an abrasive wear by brittle fracture of pre-polymerized particles and by debonding of fillers and matrix.

Nanoindentation Study on Mechanical Properties of Nano-SiO2/Dental Resin Composites

The micro/nano-scale indentation tests were performed to explore the performance of bisphenol-α-glycidyl methacrylate (Bis-GMA)/triethylene glycol dimethacrylate (TEGDMA) dental resin composites. The effect of the filling content of nano-SiO2 particles on the mechanical properties of the dental composites was studied as well. The experimental results showed that the incorporation of the nano-SiO2 particles at low concentrations (up to 10 wt.%) can apparently increase the hardness and elastic modulus of the dental rein composites. The plasticity index indicates a best elastic recovery capability at a proper amount (4 wt.%) of the nanoparticles. Combined with the infrared spectrum, the mechanical enhancement mechanisms of the dental resin composites were analyzed.

Mechanical Properties of Mo Fiber-reinforced Resin Mineral Composites with Different Mass Ratio of Resin and Hardener

Mo fibers were added to RMC with different mass ratios of resin and hardener to improve its mechanical properties. The influences of fiber surface state and hardener content on interface bonding strength and mechanical properties of RMC were studied, respectively. Furthermore, strain values of typical measuring points on samples of Mo fiber reinforced RMC(MFRRMC) under different loads were obtained by experiments and finite element analysis. The experimental results prove that scrap Mo fibers can improve interface bonding strength and mechanical properties of RMC better than new smooth Mo fibers because of the discharge pits randomly distributed on the surface of scrap fibers. With the decrease of hardener content, not only interface bonding strength between fiber and matrix, but also compression and flexural strength of MFRRMC increase firstly and then decrease. The properties are best while the mass ratio of resin and hardener reaches 4:1. It is indicated that finite element calculation data basically agree with experimental data by comparison of strain values on typical measuring points, which can provide an important intuitive reference for successive study on other mechanical properties of MFRRMC, validating the correctness of simulation method as well.

^(99m)Tc in the evaluation of microleakage of composite resin restorations with SonicFill^(TM).An in vitro experimental model

Introduction: The composite SonicFillTM (Kerr/Kavo) is indicated for posterior restorations, with a single increment up to 5 mm due to reduced polymerization shrinkage, thus reducing working time. Aim: Evaluation of marginal microleakage with SonicFillTM. Method and Materials: There were sectioned sixty noncarious human molars in the occluso-cervical direction. Class V cavities were prepared on each tooth with gingival margin walls in a standardized way. The specimens were divided into 4 groups: group 1—restored with SonicFillTM (Kerr/Kavo), group 2—restored with FiltekTM SupremeXTE (3M ESPE), group 3—the cavities were not restored;group 4—restored with SonicFillTM (Kerr/Kavo). In groups 1, 2 and 4 the enamel was conditioned with 37% orthophosphoric acid and applied the self-etch adhesive system Clear- fillTM SE BOND (Kuraray). The specimens were stored in distilled water at 37?C for 7 days. After, the specimens, were immersed in a solution of 99mTc-Pertechnetate and the radioactivity was assessed with a gamma camera. The nonparametric Kruskal-Wallis and Mann-Whitney test with Bonferroni correction at a significance level of 5% were used for the statistical analyses. Results: There are significant differences between the positive and negative control groups and between these and experimental groups (p TM and FiltekTM SupremeXTE. Conclusion: The new composite SonicFillTM and FiltekTM SupremeXTE showed no difference concerning dye penetration. The Sonic- FillTM restorative system showed no influence in concerning microleakage.

Synthesis and evaluation of a novel antibacterial dental resin composite with quaternary ammonium salts

The novel quaternary ammonium bromide (QAB)-containing oligomers were synthesized and applied for developing an antibacterial resin composite. Compressive strength (CS) and S. mutans (an oral bacteria strain) viability were used to evaluate the mechanical strength and antibacterial activity of the formed composites. All the QAB-modified resin composites showed significant antibacterial activity and mechanical strength reduction. Increasing chain length and loading significantly enhanced the antibacterial activity but dramatically reduced the CS as well. The 30-day aging study showed that the incorporation of the QAB accelerated the degradation of the composite, suggesting that the QAB may not be well suitable for development of antibacterial dental resin composites or at least the QAB loading should be well controlled, unlike its use in dental glass-ionomer cements. The work in this study is beneficial and valuable to those who are interested in studying antibacterial dental resin composites.

Mechanical Properties, Biocompatibility and Anti-Bacterial Adhesion Property Evaluation of Silicone-Containing Resin Composite with Different Formulae

Novel branched silicone methacrylate was developed.The mechanical and biological properties of the resin system were investigated to select the formula proportion with the best overall performance.The novel silicone-containing monomers were combined with an incremental sequence of glass filler concentrations in commonly used Bis-GMA/TEGDMA(50/50,wt./wt.)dental resin systems.Physicochemical properties,surface properties,antibacterial adhesion effect,anti-biofilm effect,protein adsorption,and cytotoxicity were evaluated.The results showed that BSMs did not affect the double bond conversion of dental resin,but could reduce volumetric shrinkage(p<0.05).The BSM containing resins can resist protein and bacteria adhesion(S.mutans)because it has increased hydrophobicity and a lower free energy surface(p<0.05).However,there were no statistically significant differences in cytotoxicity,surface roughness,and double bond conversion rate.Overall,the results indicate that changes in a material’s properties are not strictly proportional to its composition.Synthetic silicone resin methacrylate can reduce the polymerization shrinkage,have low surface energy and anti-adhesion properties.Silicone composite resin containing 70%matrix has the best comprehensive properties.The silicone methacrylate composite represents an innovative method to improve the properties and reducing secondary caries.

Friction and wear properties of pitch/resin densified carbon carbon composites used for airbrakes

By use of X ray diffractometry and scanning electron microscope (SEM), the friction and wear results obtained from MM 1000 dynamometer tests of CVI pitch/resin C/C composites were analyzed. By investigating the factors that affected the friction and wear properties, such as matrix carbon, application environment, graphitization degree and brake pressure, etc, friction and wear mechanism of carbon materials were probed. The results indicate that pitch densified CVI initially treated composite is more graphitizable with its graphitization degree up to 62%, and which results in uniform small debris easier to generate, more smooth friction curves with the coefficient of 0.3 ～ 0.4 and relatively higher linear wear and mass loss, compared with CVI/resin C/C composites. It was further proved by SEM observation that tribological behavior of C/C composite was system dependent. Factors determining the friction and wear properties such as the size of debris and its influence on friction and wear, brake pressure, graphization degree and debris film formation interacted and affected each other. The friction and wear mechanism of C/C composites under different high temperature treatments needs further research.