Effect of Low pH on Forming Process of Desulfurization Gypsum Composite Boards Strengthened by Melamine-formaldehyde Resin

Through exploring the effects of low pH on the composite system of desulfurization gypsum(DG)enhanced by melamine-formaldehyde resin(MF),it is found that the inducing of sulfate-ion,in contrast to chloride and oxalate ions,favors the longitudinal growth of the crystalline form of the hydration product,which was relatively simple and had the highest length to width(L/D)ratio.At the same time,MF can also improve L/D ratio of gypsum hydration products,which favors the formation of hydrated whiskers.Finally,in a composite system composed of hemihydrate gypsum,MF,and glass fibers,when dilute sulfuric acid was used to regulate pH=3-4,the tight binding formed among the components of the composite system compared to pH=5-6.The hydration product of gypsum adheres tightly to glass fiber surface and produces a good cross-linking and binding effect with MF.The flexural strength,compressive strength,elastic modulus,and water absorption of the desulphurized gypsum composite board is 22.7 MPa,39.8 MPa,5608 MPa,and 1.8%,respectively.

Investigation of Microstructure and Phase Composition of Chromic Oxide, AZS/Cr and High-alumina Refractories after Exposure of Basalt and Aluminaboronsilicate Glasses Melts

The microstructure and phase composition of high-alumina,chromic oxide,and AZS/Cr refractories containing 30%and 60%(by mass)Cr_(2)O_(3) after exposure to aluminaboronsilicate glasses and basalt melts depending on the type of melts and temperature have been studied.The mechanisms of refractory corrosion by the used melts and the factors contributing to the inhibition of corrosion development have been investigated by the method of petrographic analysis.On the basis of obtained results,the use of high-alumina,chromic oxide,and AZS/Cr refractories in the sections of glass furnace linings,experiencing the intensive impact of aluminaboronsilicate glasses and basalt melts,has been confirmed and scientifically substantiated.

A Rapid-Ab/Desorption and Portable Photothermal MIL- 101(Cr) Nanofibrous Composite Membrane Fabricated by Spray-Electrospinning for Atmosphere Water Harvesting

MIL-101(Cr)is a promising moisture absorbent for solar-driven water harvesting from moisture to tackle the worldwide water shortage issue.However,the MIL-101(Cr)powder suffers from a long ab/desorption cycle due to the crystal aggregation caused by its inherent powder properties.Here,we demonstrate a MIL-101(Cr)nanofibrous composite membrane with a nanofibrous matrix where MIL-101(Cr)is monodisperse in the 3D porous nanofibrous matrix through a simple spray-electrospinning strategy.The continuous porous nanofibrous matrix not only offers sufficient sites for MIL-101(Cr)loading but also provides rapid moisture transport channels,resulting in a super-rapid ab/desorption duration of 50 min(including an absorption process for 40 min and a desorption process for 10 min)and multicycle daily water production of 15.9 L kg^(−1) d^(−1).Besides,the MIL-101(Cr)nanofibrous composite membrane establishes a high solar absorption of 92.8%,and excellent photothermal conversion with the surface temperature of 70.7°C under one-sun irradiation.In addition,the MIL-101(Cr)nanofibrous composite membrane shows excellent potential for practical application due to its flexibility,portability,and use stability.This work provides a new perspective of shortening MOF ab/desorption duration by introducing a porous nanofibrous matrix to improve the specific water production for the solar-driven ab/desorption water harvesting technique.

Machine learning-based stiffness optimization of digital composite metamaterials with desired positive or negative Poisson's ratio

Mechanical metamaterials such as auxetic materials have attracted great interest due to their unusual properties that are dictated by their architectures.However,these architected materials usually have low stiffness because of the bending or rotation deformation mechanisms in the microstructures.In this work,a convolutional neural network(CNN)based self-learning multi-objective optimization is performed to design digital composite materials.The CNN models have undergone rigorous training using randomly generated two-phase digital composite materials,along with their corresponding Poisson's ratios and stiffness values.Then the CNN models are used for designing composite material structures with the minimum Poisson's ratio at a given volume fraction constraint.Furthermore,we have designed composite materials with optimized stiffness while exhibiting a desired Poisson's ratio(negative,zero,or positive).The optimized designs have been successfully and efficiently obtained,and their validity has been confirmed through finite element analysis results.This self-learning multi-objective optimization model offers a promising approach for achieving comprehensive multi-objective optimization.

Experimental research on shear carrying capacity of H-steel concrete composite beam with small shear span ratio

In order to investigate shear carrying capacity of H-steel concrete beam with small shear span ratio,shear test on 5 H-steel concrete composite beams with small span ratio (from 0.7 to 1.1) are reported,including test design,test scheme,test method,failure characteristics and test results. Influences of shear span ratio,web of H steel and concrete on shear carrying capacity of this kind of beam are investigated. The main components comprising shear bearing capacity are analyzed. The results show that with the shear span ratio increasing,the contribution of web of H steel and concrete on shear carrying capacity decrease. Based on test data,the calculation formula of shear carrying capacity for this beam is established by curve fitting.

Generation Mechanism of Interfacial Layer and Its Effect on Fe-Cr-Ni/Al-Si-Cu-Ni-Mg Composite Performance

Fe-Cr-Ni/Al-Si-Cu-Ni-Mg composite was taken as the experimental material. The chemical composition of interfacial layer was tested. The generation mechanism and influence of interfacial layer on the composite were analyzed. The results indicated that the generation of interfacial layer is sensitive to temperature. Interfacial layer will generate rapidly when temperature reaches 500 ℃ or above. The interfacial layer is mainly composed of Al, Si, Cu, Fe, and Cr, element Ni distributes at the outward of the interfacial layer for the precipitate of Ni later than Si and Cu, and there is almost no diffusion of Ni during the solution treatment. During heat treatment process, unequal quantity changing of metal atom results in disperse or concentrated vacancies or holes near the matrix. The existence of interfacial layer will induce a decrease of compression strength and plasticity at room temperature and an increase of strength at higher temperature comparing with composite without interfacial layer.

Preparation of Ni-Cr/BN self-lubricating composites by active sintering process

A Ni-Cr/BN composite was produced by a active sintering process. The powder of nickel carbonyl,Cr2O3 and C were used as the original materials,and a hexagonal BN(h-BN) powder was added as a solid lubricant. The influence of sintering temperature,heating rate and holding time on the properties of Ni-Cr/BN were studied. The composition and microstructure of Ni-Cr/BN were analysed by X-ray diffraction(XRD) and the optical microscopy(OM). The frictional behavior and hardness were measured with ring-block friction testing machine and Brinell hardness tester respectively. The results show that Ni-Cr is the matrix and a low-melting eutectic compound is the bonding phase in the composite. The porosity reaches 48% and the value of hardness reaches HB18 when the composite is fabricated at 1 100 ℃ for 1 h. Its wear rate is 7.44×10-5 g/min,and the average friction coefficient is 0.266. These properties make such composite suitable for use as self-lubricating material.

Experimental study and numerical analysis on dry friction and wear performance of co-continuous SiC/Fe-40Cr against SiC/2618 Al alloy composites

The dry friction and wear behaviors of co-continuous composites SiC/Fe–40Cr against SiC/Al 2618 alloy were investigated on a ring-on-ring friction and wear tester at sliding speed of 30-105 m/s under the load of 1.0-2.5 MPa. The experimental result reveals that the characteristic of two body abrasive wear and oxidation wear mechanisms are present for SiCn/2618 Al composite under higher load and sliding speed. SiC ceramic continuous network as the reinforcement can avoid composite from the third body wear that usually occurs in traditional particle reinforced composite. The mechanically mixed layer (MML) controls greatly the wear rate and friction coefficient of the composites. The composites tested at higher sliding speed exhibit higher value of friction coefficient and fluctuation, which is associated with the intermittent formation and removal of the MML. The wear and stress—strain behaviors of SiCn/Fe–40Cr against SiCn/Al 2168 at 30-105 m/s under 1.0-2.5 MPa were analyzed by finite element method with the software Solidwork2012 Simulation, respectively. The wear and stress–strain behavior of the composite predicted by the FEM correlated well with the experimental results.

晶粒尺寸对界面含Cr-O-C防黏层Cu/Ni复合体拉伸性能的影响

通过分子动力学方法研究含Cr-O-C防黏层的具有不同晶粒尺寸的Cu/Ni复合体的拉伸变形。结果表明:当Cu/Ni复合体的晶粒尺寸大于12 nm时,不论界面不含Cr、O和C原子或含有定量Cr、O和C原子,复合体的屈服强度随着晶粒尺寸的减小呈现增大趋势,符合细晶强化规律,晶粒塑性变形主要受晶体内部的位错滑移控制,最大应力增加9.52%;当晶粒尺寸小于12 nm时,由于晶界所占比例的增加,拉伸过程的塑性变形更多受晶界变形控制,屈服强度下降。Cr-O-C界面弱化了Cu/Ni复合体的强度,随着界面上Cr、O和C原子数量的增加,Cu/Ni复合体的抗拉强度随之降低,最大应力下降56.40%,Cu/Ni复合体内部的位错数量也随之降低,转移到Ni表面的Cu原子数量随之减少。

Crustal Composition of China Continent Constrained from Heat Flow Data and Helium Isotope Ratio of Underground Fluid

Based on conservation of energy principle and heat flow data in China continent, the upper limit of 1.3 μW/m3 heat production is obtained for continental crust in China. Furthermore, using the data of heat flow and helium isotope ratio of underground fluid, the heat productions of different tectonic units in China continent are estimated in range of 0.58-1.12 μW/m3 with a median of 0.85 μW/m3. Accordingly, the contents of U, Th and K20 in China crust are in ranges of 0.83-1.76 μg/g, 3.16-6.69 μg/g, and 1.0%-2.12%, respectively. These results indicate that the abundance of radioactive elements in the crust of China continent is much higher than that of Archean crust; and this fact implies China＇s continental crust is much evolved in chemical composition. Meanwhile, significant lateral variation of crustal composition is also exhibited among different tectonic units in China continent. The crust of eastern China is much enriched in incompatible elements such as U, Th and K than that of western China; and the crust of orogenic belts is more enriched than that of platform regions. It can also be inferred that the crusts of eastern China and orogenic belts are much felsic than those of western China and platform regions, respectively, derived from the positive correlation between the heat production and SiO2 content of bulk crust. This deduction is consistent with the results derived from the crustal seismic velocity data in China. According to the facts of the lower seismic velocity of China than the average value of global crust, and the higher heat production of China continent compared with global crust composition models published by previous studies, it is deduced that the average composition models of global continent crust by Rudnick and Fountain （1995）, Rudnick and Gao （2003）, Weaver and Tarney （1984）, Shaw et al. （1986）, and Wedepohl （1995） overestimate the abundance of incompatible elements such as U, Th and K of continental crust.

低压冷喷涂制备Al-Ni-xCr复合涂层及其磨损特性研究

防腐性能较好的铝基涂层存在耐磨性不足的问题。本文设计了Ni粉和Cr粉复合沉积的方法来改善涂层的耐磨性。采用低压冷喷涂技术,制备了一系列Cr含量不同的Al-Ni-xCr复合涂层。通过金相、扫描电镜及X射线衍射等方法分析了复合涂层的微观形貌和成分。采用显微硬度计和磨损仪测试了涂层的显微硬度和磨损曲线,结合磨痕形貌分析了复合涂层的磨损机理。研究得出:低压冷喷涂可实现Al、Cr、Ni三种金属粉的共沉积,并获得致密、均匀的Al-Ni-xCr复合涂层。枝晶状Ni粉沉积率较高,Cr粉沉积率较低。含70 wt.%Cr的混粉涂层中,Cr含量约为31 wt.%。硬质颗粒Cr同时起到夯实涂层的作用,随着Cr含量增加,Al-Ni-xCr复合涂层的致密性提高。Al-Ni-xCr复合涂层的耐磨性能主要来自于Cr而非Ni,且与Cr含量有关。Al-Ni-70Cr复合涂层耐磨性最佳,磨损率仅为Al涂层的1/2。其优异的耐磨性归因于摩擦界面形成了稳定的、较硬的、含Cr量较高的复合氧化膜,抑制了磨损过程。

Microstructure and hardness of WC-Co particle reinforced iron matrix surface composite

In this study, a high Cr cast iron surface composite material reinforced with WC-Co particles 2-6 mm in size was prepared using a pressureless sand mold infiltration casting technique. The composition, microstructure and hardness were determined by means of energy dispersive spectrometry(EDS), electron probe microanalysis(EPMA), scanning electron microscope(SEM) and Rockwell hardness measurements. It is determined that the obtained composite layer is about 15 mm thick with a WC-Co particle volumetric fraction of ～38%. During solidification, interface reaction takes place between WC-Co particles and high chromium cast iron. Melting and dissolving of prefabricated particles are also found, suggesting that local Co melting and diffusion play an important role in promoting interface metallurgical bonding. The composite layer is composed of ferrite and a series of carbides, such as(Cr, W, Fe)23C6, WC, W2C, M6C and M12C. The inhomogeneous hardness in the obtained composite material shows a gradient decrease from the particle reinforced metal matrix composite layer to the matrix layer. The maximum hardness of 86.3 HRA(69.5 HRC) is obtained on the particle reinforced surface, strongly indicating that the composite can be used as wear resistant material.

Effects of Water/Binder Ratio on the Properties of Engineered Cementitious Composites

The effects of water/binder ratio （w/b） on the toughness behavior, compressive strength and flexural strength of engineered cementitious composites （ECC） were investigated. The w/b ratios of 0.25, 0.31, 0.33 and 0.37 were selected and the specimens were tested at the ages of 7 d and 28 d. The experimental results showed that there was a corresponding increase in first cracking strength, modulus of rupture, compressive strength and flexural strength with the decrease of w/b. Within the w/b range of 0.25-0.37, higher w/b was found to have improved effects on deflection, strain hardening index and toughness index of ECC. In the permission of meeting the requirement of compressive strength grade, selecting higher w/b in mix design will help to obtain robust ECC.

Flexural behavior of reinforced concrete beams with high performance fiber reinforced cementitious composites

This article presents an experimental study on the flexural performance of reinforced concrete(RC)beams with fiber reinforced cementitious composites(FRCC)and hybrid fiber reinforced cementitious composites(HFRCC)in the hinge portion.Beam specimens with moderate confinement were used in the study and tested under monotonic loading.Seven diverse types of FRCC including hybrid composites using fibers in different profiles and in different volumes are employed in this study.Companion specimens such as cylindrical specimens and prism specimens are also used to study the physical properties of composites employed.The moment?curvature,stiffness behavior,ductility,crack pattern and modified flexural damage ratio are the main factors considered in this study to observe the efficacy of the employed hybrid composites.The experimental outputs demonstrate the improved post yield behavior with less rate of stiffness degradation and better damage tolerance capacity than conventional technique.

High Cr white cast iron/carbon steel bimetal liner by lost foam casting with liquid-liquid composite process

Liners in wet ball mill for mineral processing industry must bear abrasive wear and corrosive wear, and consequently, the service life of the liner made from traditional materials, such as Hadfield steel and alloyed steels, is typically less than ten months. Bimetal liner, made from high Cr white cast iron and carbon steel, has been successfully developed by using liquid-liquid composite lost foam casting process. The microstructure and interface of the composite were analyzed using optical microscope, SEM, EDX and XRD. Micrographs indicate that the boundary of bimetal combination regions is staggered like dogtooth, two liquid metals are not mixed, and the interface presents excellent metallurgical bonding state. After heat treatment, the composite liner specimens have shown excellent properties, including hardness 〉 61 HRC, fracture toughness ak 〉16.5 J.cm2 and bending strength 〉1,600 MPa. Wear comparison was made between the bimetal composite liner and alloyed steel liner in an industrial hematite ball mill of WISCO, and the results of eight-month test in wet grinding environment have proved that the service life of the bimetal composite liner is three times as long as that of the alloyed steel liner.

Wear resistance of Zr/WC composite coatings on Cr12MoV steel surface by electric spark deposition

Zr/WC composite coating was prepared on the surface of Cr12MoV steel by electric spark deposition technology to change its surface properties. The surface and worn surface morphology of the coating were observed using scanning electron microscope. Dry friction and wear tests of the coatings were carried out at room temperature. The results show that the coating is continuous and uniform, and the thickness was about 50-60 μm. The microhardness of the coating surface was highest at 1140 HV_(200g), which was significantly higher than that of the substrate. The ear tests results show that the wear weight loss, wear volume and wear rate follow the following rules: Cr12MoV>WC coating> Zr/WC composite coating.

Pile-soil stress ratio in bidirectionally reinforced composite ground by considering soil arching effect

To discuss the soil arching effect on the load transferring model and sharing ratios by the piles and inter-pile subsoil in the bidirectionally reinforced composite ground, the forming mechanism, mechanical behavior and its effect factors were discussed in detail. Then, the unified strength theory was introduced to set up the elastoplastic equilibrium differential equation of the subsoil under the limit equilibrium state. And from the equation, the solutions were derived with the corresponding formulas presented to calculate the earth pressure over and beneath the horizontal reinforced cushion or pillow, the stress of inter-pile subsoil and the pile-soil stress ratio. Based on the obtained solutions and measured data from an engineering project, the influence rules by the soil property parameters (i.e., the cohesion c and internal friction angle φ) and pile spacing on the pile-soil stress ratio n were discussed respectively. The results show that to improve the load sharing ratio by the piles, the more effective means for filling materials with a larger value of φ is to increase the ratio of pile cap size to spacing, while to reduce the pile spacing properly and increase the value of cohesion c is advisable for those filling materials with a smaller value of φ.

Mechanical properties and wear resistance of medium entropy Fe40Mn40Cr10Co10/TiC composites

The Fe40Mn40Cr10Co10/TiC (volume fraction of TiC, 10%) composites were synthesized in combination of ball milling and spark plasma sintering (SPS) in the present work. Mechanical properties and wear resistance of the Fe40Mn40Cr10Co10/TiC composites were individually investigated. It was found that TiC particles homogenously distributed in the Fe40Mn40Cr10Co10/TiC composite after being sintered at 1373 K for 15 min. Meanwhile, grain refinement was observed in the as-sintered composite. Compared with the pure Fe40Mn40Cr10Co10 medium entropy alloy (MEA) matrix grain, addition of 10% TiC particles resulted in an increase in the compressive strength from 1.571 to 2.174 GPa, and the hardness from HV 320 to HV 872. Wear resistance results demonstrated that the friction coefficient, wear depth and width of the composite decreased in comparison with the Fe40Mn40Cr10Co10 MEA matrix. Excellent mechanical properties and wear resistance could offer the Fe40Mn40Cr10Co10/TiC composite a very promising candidate for engineering applications.

GO/CS复合微球的制备及其对Cr(Ⅵ)的吸附性能

重金属六价铬离子对环境有着严重的污染,研发一种高效的吸附剂很有必要。采用相转变法制得壳聚糖/氧化石墨烯复合材料(GO/CS)。通过X-射线衍射仪(XRD)、傅里叶变换红外光谱仪(FT-IR)、扫描电子显微镜(SEM)对微球的结构、表面形貌等进行了表征,并探究了复合微球的滴球温度、吸附剂加入量、Cr(Ⅵ)溶液初始浓度、吸附温度、吸附时间、吸附溶液pH、微球粒径等因素对Cr(Ⅵ)吸附性能的影响。结果表明:在滴球温度为30℃,吸附剂加入量为0.3 g、Cr(Ⅵ)溶液初始浓度为40 mg/L、吸附温度为40℃、吸附时间为120 min、吸附溶液pH=4的条件下,壳聚糖/氧化石墨烯复合微球对Cr(Ⅵ)的吸附性能达到最高,最大吸附率达84.98%。

Microwave Absorption Properties of Carbon Nanotubes-Epoxy Composites in a Frequency Range of 2 - 20 GHz

In this work, multi-walled carbon nanotubes (MWCNTs)-epoxy composites with MWCNTs (outer diameter less 8 nm) loadings from 1 to 10 wt% were fabricated. The microstructures, dielectric constant, and microwave absorption properties of the MWCNTs-epoxy composite samples were investigated. The measurement results showed that the microwave absorption ratio of the MWCNTs-epoxy composite strongly depend on the MWCNT loading in the composites. The microwave absorption ratio up to 20%-26% around 18-20 GHz was reached for the samples with 8-10 wt% MWCNT loadings. The high absorption performance is mainly attributed to the microwave absorption of MWCNTs and the dielectric loss of MWCNTs-epoxy composites.