The snap-through behaviors and nonlinear vibrations are investigated for a bistable composite laminated cantilever shell subjected to transversal foundation excitation based on experimental and theoretical approaches....The snap-through behaviors and nonlinear vibrations are investigated for a bistable composite laminated cantilever shell subjected to transversal foundation excitation based on experimental and theoretical approaches.An improved experimental specimen is designed in order to satisfy the cantilever support boundary condition,which is composed of an asymmetric region and a symmetric region.The symmetric region of the experimental specimen is entirely clamped,which is rigidly connected to an electromagnetic shaker,while the asymmetric region remains free of constraint.Different motion paths are realized for the bistable cantilever shell by changing the input signal levels of the electromagnetic shaker,and the displacement responses of the shell are collected by the laser displacement sensors.The numerical simulation is conducted based on the established theoretical model of the bistable composite laminated cantilever shell,and an off-axis three-dimensional dynamic snap-through domain is obtained.The numerical solutions are in good agreement with the experimental results.The nonlinear stiffness characteristics,dynamic snap-through domain,and chaos and bifurcation behaviors of the shell are quantitatively analyzed.Due to the asymmetry of the boundary condition and the shell,the upper stable-state of the shell exhibits an obvious soft spring stiffness characteristic,and the lower stable-state shows a linear stiffness characteristic of the shell.展开更多
In order to effectively describe the progressively intralaminar and interlam- inar damage for composite laminates, a three dimensional progressive damage model for composite laminates to be used for low-velocity impac...In order to effectively describe the progressively intralaminar and interlam- inar damage for composite laminates, a three dimensional progressive damage model for composite laminates to be used for low-velocity impact is presented. Being applied to three-dimensional (3D) solid elements and cohesive elements, the nonlinear damage model can be used to analyze the dynamic performance of composite structure and its failure be- havior. For the intralaminar damage, as a function of the energy release rate, the damage model in an exponential function can describe progressive development of the damage. For the interlaminar damage, the damage evolution is described by the framework of the continuum mechanics through cohesive elements. Coding the user subroutine VUMAT of the finite element software ABAQUS/Explicit, the model is applied to an example, i.e., carbon fiber reinforced epoxy composite laminates under low-velocity impact. It is shown that the prediction of damage and deformation agrees well with the experimental results.展开更多
The composite laminates with embedded acrylonitrile butadiene rubber (NBR) layer were fabricated by cocuring process. The embedded layers were perforated with a series of small holes to allow resin to flow through t...The composite laminates with embedded acrylonitrile butadiene rubber (NBR) layer were fabricated by cocuring process. The embedded layers were perforated with a series of small holes to allow resin to flow through the damping layer and completely couple the structure to improve bending stiffness and interlaminar shearing strength of these cocured composite laminates. The damping, bending stiffness and shearing strength of these composite laminates with different perforation diameters were investigated. The experimental results show that increasing the perforation diameter leads to significant decreases in damping and significant increase in bending stiffness up to an area ratio of 7.065%. The area ratio here is defined as the ratio of perforation area to the total damping area. Beyond the area ratio of 7.065%, increasing the diameter to an area ratio of 50.24% results in only a slight variation in damping and bending stiffness. Moreover, increasing the perforation diameter does not always increase the shearing strength of the embedded viscoelastic layer. The shearing strength of embedded viscoelastic layer increases only when the area ratio is greater than 19.625%; instead, it will decrease.展开更多
The double Hopf bifurcation of a composite laminated piezoelectric plate with combined external and internal excitations is studied. Using a multiple scale method, the average equations are obtained in two coordinates...The double Hopf bifurcation of a composite laminated piezoelectric plate with combined external and internal excitations is studied. Using a multiple scale method, the average equations are obtained in two coordinates. The bifurcation response equations of the composite laminated piezoelectric plate with the primary parameter resonance, i.e., 1:3 internal resonance, are achieved. Then, the bifurcation feature of bifurcation equations is considered using the singularity theory. A bifurcation diagram is obtained on the parameter plane. Different steady state solutions of the average equations are analyzed. By numerical simulation, periodic vibration and quasi-periodic vibration responses of the Composite laminated piezoelectric plate are obtained.展开更多
According to traditional phenomenological fatigue methodology and moderncontinuum damage mechanics theory, dual fatigue cumulative damage rules to predict fatigue damageformation and propagation lives of the notched c...According to traditional phenomenological fatigue methodology and moderncontinuum damage mechanics theory, dual fatigue cumulative damage rules to predict fatigue damageformation and propagation lives of the notched composite laminates are presented. A 3-dimensionaldamage constitutive equation of anisotropic composites is also established. Damage strain energyrelease rate is interpreted as a driving force of the fatigue delamination damage propagation. A newdamage evolution equation and a damage propagation σ_a-σ_m-N~* surface (stress amplitude-meanstress-life surface) are derived. Hence, using the method above, the fatigue life of compositecomponents can be predicted. Finally, theoretically predicted results are compared with experimentaldata. It is found that the deviation of theoretic prediction from experimental results is about22%.展开更多
Presented herein is a methodology for the multi-objective optimization of damping and bending stiffness of cocoured composite laminates with embedded viscoelastic damping layer. The embedded viscoelastic damping layer...Presented herein is a methodology for the multi-objective optimization of damping and bending stiffness of cocoured composite laminates with embedded viscoelastic damping layer. The embedded viscoelastic damping layer is perforated with a series of small holes, and the ratio of the perforation area to the total damping area is the design variable of the methodology. The multi-objective optimization is converted into a single-objective problem by an evaluation function which is a liner weigh sum of the two sub-objective functions. The proposed methodology was carried out to determine the optimal perforation area ratios of two viscoelstic layers with different perforation distance embedded in two composite plates. Both the optimal perforation area ratios are approximate to 2.2%. However, the objective value of the plate with greater perforation distance in embedded viscoelatic layer is much greater.展开更多
The extended Kantorovich method is employed to study the local stress concentrations at the vicinity of free edges in symmetrically layered composite laminates subjected to uniaxial tensile load upon polynomial stress...The extended Kantorovich method is employed to study the local stress concentrations at the vicinity of free edges in symmetrically layered composite laminates subjected to uniaxial tensile load upon polynomial stress functions. The stress fields are initially assumed by means of the Lekhnitskii stress functions under the plane strain state. Applying the principle of complementary virtual work,the coupled ordinary differential equations are obtained in which the solutions can be obtained by solving a generalized eigenvalue problem. Then an iterative procedure is established to achieve convergent stress distributions. It should be noted that the stress function based extended Kantorovich method can satisfy both the traction-free and free edge stress boundary conditions during the iterative processes. The stress components near the free edges and in the interior regions are calculated and compared with those obtained results by finite element method(FEM). The convergent stresses have good agreements with those results obtained by three dimensional(3D) FEM. For generality, various layup configurations are considered for the numerical analysis. The results show that the proposed polynomial stress function based extended Kantorovich method is accurate and efficient in predicting the local stresses in composite laminates and computationally much more efficient than the 3D FEM.展开更多
In the present paper, a series of hierarchical warping functions is developed to analyze the static and dynamic problems of thin walled composite laminated helicopter rotors composed of several layers with single clos...In the present paper, a series of hierarchical warping functions is developed to analyze the static and dynamic problems of thin walled composite laminated helicopter rotors composed of several layers with single closed cell. This method is the development and extension of the traditional constrained warping theory of thin walled metallic beams, which had been proved very successful since 1940s. The warping distribution along the perimeter of each layer is expanded into a series of successively corrective warping functions with the traditional warping function caused by free torsion or free beading as the first term, and is assumed to be piecewise linear along the thickness direction of layers. The governing equations are derived based upon the variational principle of minimum potential energy for static analysis and Rayleigh Quotient for free vibration analysis. Then the hierarchical finite element method. is introduced to form a,. numerical algorithm. Both static and natural vibration problems of sample box beams axe analyzed with the present method to show the main mechanical behavior of the thin walled composite laminated helicopter rotor.展开更多
In view of rite effective elastic moduli theory([1]), analyzing the thick composite laminated bars subjected to an externally applied torque are presented by three-dimensional finite element (3-D FEM) and global-local...In view of rite effective elastic moduli theory([1]), analyzing the thick composite laminated bars subjected to an externally applied torque are presented by three-dimensional finite element (3-D FEM) and global-local method in this paper. Numerical results involving the distribution of shearing stresses olt cross-section and the torsional deformation and the interlaminar stresses near to free edges are given. If necessary elements discretization may be densely carried out only in the high stress gradient, region. Obviously, it requires less computer memory and computational time so that it offers an effective way for evaluating strength of laminated bars torsion with a greet number of layers.展开更多
In the symplectic space composed of the original variables,displacements,and their dual variables,stresses,the symplectic solution for the composite laminates based on the Pipes-Pagano model is established in this pap...In the symplectic space composed of the original variables,displacements,and their dual variables,stresses,the symplectic solution for the composite laminates based on the Pipes-Pagano model is established in this paper.In contrast to the traditional technique using only one kind of variables,the symplectic dual variables include displacement components as well as stress components.Therefore,the compatibility conditions of displacement and stress at interfaces can be formulated simultaneously.After being introduced into the symplectic dual system,the uniform schemes,such as the separation of variables and symplectic eigenfunction expansion method,can be implemented conveniently to analyze composite laminate problems.An analytical solution for the free edge effect of composite laminates is obtained,showing the effectiveness of the symplectic dual method in analyzing composite laminates.展开更多
The effects of an external store on the flutter characteristics of a composite laminated plate in a supersonic flow are investigated. The Dirac function is used to formulate the interaction between the plate and the s...The effects of an external store on the flutter characteristics of a composite laminated plate in a supersonic flow are investigated. The Dirac function is used to formulate the interaction between the plate and the store. The first-order piston theory is used to describe the aerodynamic load. The governing equation of the composite laminated plate with an external store is established based on the Hamilton principle. The mode shapes are constructed by the admissible functions which axe a set of characteristic orthogonal polynomials generated directly by the Gram-Schmidt process, and the boundary constraint is modeled as the artificial springs. The frequency and mode shapes of the plate under different boundaries are determined by the Rayleigh-Ritz method. The validity of the proposed approach is confirmed by comparing the results with those obtained from the finite element method (FEM). The effects of the mounting position, the center of gravity position and the mounting points spacing of the external store on the flutter boundary are discussed for both the simply supported and cantilever plates, respectively, which correspond to the two installation sites of the external store, i.e., the belly and wings of the aircraft.展开更多
A study of postbuckling and delamination propagation behavior in delaminated stiffened composite plates was presented. A methodology was proposed for simulating the multi-failure responses, such as initial and postbuc...A study of postbuckling and delamination propagation behavior in delaminated stiffened composite plates was presented. A methodology was proposed for simulating the multi-failure responses, such as initial and postbuckling, delamination onset and propagation, etc. A finite element analysis was conducted on the basis of the Mindlin first order shear effect theory and the von-Krmn nonlinear deformation assumption. The total energy release rate used as the criteria of delamination growth was estimated with virtual crack closure technique (VCCT). A self-adaptive grid moving technology was adopted to model the delamination growth process. Moreover, the contact effect along delamination front was also considered during the numerical simulation process. By some numerical examples, the influence of distribution and location of stiffener, configuration and size of the delamination, boundary condition and contact effect upon the delamination growth behavior of the stiffened composite plates were investigated. The method and numerical conclusion provided should be of great value to engineers dealing with composite structures.展开更多
A constitutive model for composite laminated plates with the damage effect of the intra-layers and inter-laminar interface is presented. The model is based on the general six-degrees-of-freedom plate theory, the disco...A constitutive model for composite laminated plates with the damage effect of the intra-layers and inter-laminar interface is presented. The model is based on the general six-degrees-of-freedom plate theory, the discontinuity of displacement on the interfaces are depicted by three shape functions, which are formulated according to solutions satisfying three equilibrium equations, By using the variation principle, the three-dimensional non-linear equilibrium differential equations of the laminated plates with two different damage models are derived. Then, considering a simply supported laminated plate with damage, an analytical solution is presented using finite difference method to obtain the inter-laminar stresses.展开更多
A general anisotropic damage theory of cracked laminates is formulated here.The deformation of composite laminates is composed of matrix elastic strains,pseudo-elastic damage strains due to cracking and permanent dama...A general anisotropic damage theory of cracked laminates is formulated here.The deformation of composite laminates is composed of matrix elastic strains,pseudo-elastic damage strains due to cracking and permanent damage strains due to interlaminar slip.The surface of damage initiation is constructed accord- ing to the concept of linear elastic fracture mechanics for the virgin material.After the initial damage,a pesudo-elastic damage can be used to describe the damage behaviour if interlaminar slip is negligible.Damage evolution,load induced anisotropy and interlaminar-intralaminar interaction for composite laminates are exam- ined;the latter can perturb the normality structure of damage strain rate.Explicit expressions are given for pseudo-elastic (or secant) moduli of the damaging composite laminates,under a non-interacting assumption imposed on the cracks between different families.展开更多
The testing on the bearing strength of single-shear bolt jointed composite laminates structure is done.And the effect of the fixture on the testing results is analyzed. Then a macro-micro multi-scale analytical model ...The testing on the bearing strength of single-shear bolt jointed composite laminates structure is done.And the effect of the fixture on the testing results is analyzed. Then a macro-micro multi-scale analytical model combined with the improved"Generalized Method of Cells( GMC) "is developed,which is used to predict the macro bearing strength and to characterize the micro constitute material failure of the bolt jointed composite laminates structure. Both the contact conditions at the bolt/hole boundary and the contact conditions at the specimen/fixture boundary,progressive damage,and the material properties degradation are all taken account into the analytical model. Thus,the numerical simulation results agree well with the experimental results.Finally,the effect of the fixture on the testing results is characterized. The results show that the incomplete contaction between the fixture and the specimen or the lack of the lateral constraint on the specimen will affect the limited bearing strength and the offset bearing strength of the bolt jointed composite laminates structure. In addition,the lower support rigid of the fixture will affect the rigid of the bolt jointed composite laminates structure.展开更多
The study on properly degradation of damaged,.onlj,osile laminates is extendedto anisotropic laminates with matrix cracking. In (II) of the paper, a solution forpartitioned stiffness is given to complete the consti...The study on properly degradation of damaged,.onlj,osile laminates is extendedto anisotropic laminates with matrix cracking. In (II) of the paper, a solution forpartitioned stiffness is given to complete the constitutive relations developed in (I) Thestiffness degradation in cracked laminates is calculated and the results arediscussed.展开更多
Effects of layer quantities and stacking sequences on L-shape composite manufacturing qualities in using OOA(out-of-autoclave)prepregs were studied.The mechanisms of air evacuated in 5 kinds of lay-ups were revealed b...Effects of layer quantities and stacking sequences on L-shape composite manufacturing qualities in using OOA(out-of-autoclave)prepregs were studied.The mechanisms of air evacuated in 5 kinds of lay-ups were revealed by image analysis of cut surfaces and thickness measurements.Results show that air in OOA prepregs is evacuated in two ways.Most of the air is forced out of layers directly by vacuum before air accesses in prepregs closed.Very little entrapped air moves perpendicularly to outer layers under hydrostatic resin pressure.When a laminate contains less than 16 layers,voids can hardly be found in layers.When a laminate contains more than 16 layers,voids cannot be expelled completely during the window of vertical movement.As for stacking sequences,the synergetic effect of slip function and nest function determines the thickness and voids content of laminates.Results show that the average of single layer thickness of unidirectional layers is the lowest,and the average of single layer thickness of quasi-isotropic layers is the highest.The voids content of quasi isotropic is the highest,which is consistent with the theoretical analysis.展开更多
The vibration attenuation and damping characteristics of carbon fiber reinforced composite laminates with different thicknesses were investigated by hammering experiments under free boundary constraints in different d...The vibration attenuation and damping characteristics of carbon fiber reinforced composite laminates with different thicknesses were investigated by hammering experiments under free boundary constraints in different directions.The dynamic signal testing and analysis system is applied to collect and analyze the vibration signals of the composite specimens,and combine the self-spectrum analysis and logarithmic decay method to identify the fundamental frequencies of different specimens and calculate the damping ratios of different directions of the specimens.The results showed that the overall stiffness of the specimen increased with the increase of the specimen thickness,and when the thickness of the sample increases from 24mm to 32mm,the fundamental frequency increases by 35.1%,the vibration showed the same vibration attenuation and energy dissipation characteristics in the 0°and 90°directions of the specimen,compared with the specimen in the 45°direction,which was less likely to be excited and had poorer vibration attenuation ability,while the upper and lower surfaces of the same specimen showed slightly different attenuation characteristics to the vibration,the maximum difference of damping capacity between top and bottom surfaces of CFRP plates is about 70%.展开更多
A new higher-order shear deformation theory based on global-local superposition technique is developed. The theory satisfies the free surface conditions and the geometric and stress continuity conditions at interfaces...A new higher-order shear deformation theory based on global-local superposition technique is developed. The theory satisfies the free surface conditions and the geometric and stress continuity conditions at interfaces. The global displacement components are of the Reddy theory and local components are of the internal first to third-order terms in each layer. A two-node beam element based on this theory is proposed. The solutions are compared with 3D-elasticity solutions. Numerical results show that present beam element has higher computational efficiency and higher accuracy.展开更多
Fatigue tests of the smooth composite laminates and the notched composite laminates under compressive cyclic loading have been carried out. The damage mechanism is discussed and analyzed. Damage evolution is monitored...Fatigue tests of the smooth composite laminates and the notched composite laminates under compressive cyclic loading have been carried out. The damage mechanism is discussed and analyzed. Damage evolution is monitored using stiffness decay. From these tests, it is found that the initial delamination occurs at the free boundary of smooth specimens, or the notch boundary of notched specimens, subjected to the compression-compression cyclic load. A point of view in relation to two-phases of compression fatigue delamination of composites is proposed, namely, compression-compression delamination consists of the delamination formation phase and the delamination propagation, and there is a 'damage transition point' to separate this two-phases. Furthermore, an empirical modulus degradation formula and its parameters fitting method are presented. According to the test data handling results, it is shown that this formula is univocal and can fit the test data conveniently. In addition, two kinds of new anti-buckling devices are designed for these tests. At last, the E-N curves, the D-N curves and the S-N curve of the smooth carbon fiber reinforced composite laminates of T300/648C are determined to predict the fatigue life of the notched composite laminate. And the E-N curve of the notched specimens at the given load ratio R = 10 and minimum load Pmin = -0.45 kN is also measured to verify the estimated result of fatigue life.展开更多
基金Project supported by the National Natural Science Foundation of China(Nos.11832002 and 12072201)。
文摘The snap-through behaviors and nonlinear vibrations are investigated for a bistable composite laminated cantilever shell subjected to transversal foundation excitation based on experimental and theoretical approaches.An improved experimental specimen is designed in order to satisfy the cantilever support boundary condition,which is composed of an asymmetric region and a symmetric region.The symmetric region of the experimental specimen is entirely clamped,which is rigidly connected to an electromagnetic shaker,while the asymmetric region remains free of constraint.Different motion paths are realized for the bistable cantilever shell by changing the input signal levels of the electromagnetic shaker,and the displacement responses of the shell are collected by the laser displacement sensors.The numerical simulation is conducted based on the established theoretical model of the bistable composite laminated cantilever shell,and an off-axis three-dimensional dynamic snap-through domain is obtained.The numerical solutions are in good agreement with the experimental results.The nonlinear stiffness characteristics,dynamic snap-through domain,and chaos and bifurcation behaviors of the shell are quantitatively analyzed.Due to the asymmetry of the boundary condition and the shell,the upper stable-state of the shell exhibits an obvious soft spring stiffness characteristic,and the lower stable-state shows a linear stiffness characteristic of the shell.
基金supported by the National Natural Science Foundation of China(No.11072202)
文摘In order to effectively describe the progressively intralaminar and interlam- inar damage for composite laminates, a three dimensional progressive damage model for composite laminates to be used for low-velocity impact is presented. Being applied to three-dimensional (3D) solid elements and cohesive elements, the nonlinear damage model can be used to analyze the dynamic performance of composite structure and its failure be- havior. For the intralaminar damage, as a function of the energy release rate, the damage model in an exponential function can describe progressive development of the damage. For the interlaminar damage, the damage evolution is described by the framework of the continuum mechanics through cohesive elements. Coding the user subroutine VUMAT of the finite element software ABAQUS/Explicit, the model is applied to an example, i.e., carbon fiber reinforced epoxy composite laminates under low-velocity impact. It is shown that the prediction of damage and deformation agrees well with the experimental results.
基金supported from the Center for Composites Material and Structure of Harbin Institute of Technology,China
文摘The composite laminates with embedded acrylonitrile butadiene rubber (NBR) layer were fabricated by cocuring process. The embedded layers were perforated with a series of small holes to allow resin to flow through the damping layer and completely couple the structure to improve bending stiffness and interlaminar shearing strength of these cocured composite laminates. The damping, bending stiffness and shearing strength of these composite laminates with different perforation diameters were investigated. The experimental results show that increasing the perforation diameter leads to significant decreases in damping and significant increase in bending stiffness up to an area ratio of 7.065%. The area ratio here is defined as the ratio of perforation area to the total damping area. Beyond the area ratio of 7.065%, increasing the diameter to an area ratio of 50.24% results in only a slight variation in damping and bending stiffness. Moreover, increasing the perforation diameter does not always increase the shearing strength of the embedded viscoelastic layer. The shearing strength of embedded viscoelastic layer increases only when the area ratio is greater than 19.625%; instead, it will decrease.
基金Project supported by the National Natural Science Foundation of China(Nos.11402127,11290152 and 11072008)
文摘The double Hopf bifurcation of a composite laminated piezoelectric plate with combined external and internal excitations is studied. Using a multiple scale method, the average equations are obtained in two coordinates. The bifurcation response equations of the composite laminated piezoelectric plate with the primary parameter resonance, i.e., 1:3 internal resonance, are achieved. Then, the bifurcation feature of bifurcation equations is considered using the singularity theory. A bifurcation diagram is obtained on the parameter plane. Different steady state solutions of the average equations are analyzed. By numerical simulation, periodic vibration and quasi-periodic vibration responses of the Composite laminated piezoelectric plate are obtained.
基金This project is supported by National Natural Science Foundation of China (No.50005003)Aeronautic Science Foundation of China (No.0lA5l0l1)
文摘According to traditional phenomenological fatigue methodology and moderncontinuum damage mechanics theory, dual fatigue cumulative damage rules to predict fatigue damageformation and propagation lives of the notched composite laminates are presented. A 3-dimensionaldamage constitutive equation of anisotropic composites is also established. Damage strain energyrelease rate is interpreted as a driving force of the fatigue delamination damage propagation. A newdamage evolution equation and a damage propagation σ_a-σ_m-N~* surface (stress amplitude-meanstress-life surface) are derived. Hence, using the method above, the fatigue life of compositecomponents can be predicted. Finally, theoretically predicted results are compared with experimentaldata. It is found that the deviation of theoretic prediction from experimental results is about22%.
文摘Presented herein is a methodology for the multi-objective optimization of damping and bending stiffness of cocoured composite laminates with embedded viscoelastic damping layer. The embedded viscoelastic damping layer is perforated with a series of small holes, and the ratio of the perforation area to the total damping area is the design variable of the methodology. The multi-objective optimization is converted into a single-objective problem by an evaluation function which is a liner weigh sum of the two sub-objective functions. The proposed methodology was carried out to determine the optimal perforation area ratios of two viscoelstic layers with different perforation distance embedded in two composite plates. Both the optimal perforation area ratios are approximate to 2.2%. However, the objective value of the plate with greater perforation distance in embedded viscoelatic layer is much greater.
基金supported by the National Natural Science Foundation of China (Grants 11372145, 11372146, and 11272161)the State Key Laboratory of Mechanics and Control of Mechanical Structures (Nanjing University of Aeronautics and astronautics) (Grant MCMS-0516Y01)+1 种基金Zhejiang Provincial Top Key Discipline of Mechanics Open Foundation (Grant xklx1601)the K. C. Wong Magna Fund through Ningbo University
文摘The extended Kantorovich method is employed to study the local stress concentrations at the vicinity of free edges in symmetrically layered composite laminates subjected to uniaxial tensile load upon polynomial stress functions. The stress fields are initially assumed by means of the Lekhnitskii stress functions under the plane strain state. Applying the principle of complementary virtual work,the coupled ordinary differential equations are obtained in which the solutions can be obtained by solving a generalized eigenvalue problem. Then an iterative procedure is established to achieve convergent stress distributions. It should be noted that the stress function based extended Kantorovich method can satisfy both the traction-free and free edge stress boundary conditions during the iterative processes. The stress components near the free edges and in the interior regions are calculated and compared with those obtained results by finite element method(FEM). The convergent stresses have good agreements with those results obtained by three dimensional(3D) FEM. For generality, various layup configurations are considered for the numerical analysis. The results show that the proposed polynomial stress function based extended Kantorovich method is accurate and efficient in predicting the local stresses in composite laminates and computationally much more efficient than the 3D FEM.
基金The project supported by the National Natural Science Foundation of China (19932030)
文摘In the present paper, a series of hierarchical warping functions is developed to analyze the static and dynamic problems of thin walled composite laminated helicopter rotors composed of several layers with single closed cell. This method is the development and extension of the traditional constrained warping theory of thin walled metallic beams, which had been proved very successful since 1940s. The warping distribution along the perimeter of each layer is expanded into a series of successively corrective warping functions with the traditional warping function caused by free torsion or free beading as the first term, and is assumed to be piecewise linear along the thickness direction of layers. The governing equations are derived based upon the variational principle of minimum potential energy for static analysis and Rayleigh Quotient for free vibration analysis. Then the hierarchical finite element method. is introduced to form a,. numerical algorithm. Both static and natural vibration problems of sample box beams axe analyzed with the present method to show the main mechanical behavior of the thin walled composite laminated helicopter rotor.
文摘In view of rite effective elastic moduli theory([1]), analyzing the thick composite laminated bars subjected to an externally applied torque are presented by three-dimensional finite element (3-D FEM) and global-local method in this paper. Numerical results involving the distribution of shearing stresses olt cross-section and the torsional deformation and the interlaminar stresses near to free edges are given. If necessary elements discretization may be densely carried out only in the high stress gradient, region. Obviously, it requires less computer memory and computational time so that it offers an effective way for evaluating strength of laminated bars torsion with a greet number of layers.
基金supported by the National Basic Research Program of China (No. 2010CB832704)the National Natural Science Foundation of China (No. 10772039)
文摘In the symplectic space composed of the original variables,displacements,and their dual variables,stresses,the symplectic solution for the composite laminates based on the Pipes-Pagano model is established in this paper.In contrast to the traditional technique using only one kind of variables,the symplectic dual variables include displacement components as well as stress components.Therefore,the compatibility conditions of displacement and stress at interfaces can be formulated simultaneously.After being introduced into the symplectic dual system,the uniform schemes,such as the separation of variables and symplectic eigenfunction expansion method,can be implemented conveniently to analyze composite laminate problems.An analytical solution for the free edge effect of composite laminates is obtained,showing the effectiveness of the symplectic dual method in analyzing composite laminates.
基金supported by the National Natural Science Foundation of China(No.11472089)
文摘The effects of an external store on the flutter characteristics of a composite laminated plate in a supersonic flow are investigated. The Dirac function is used to formulate the interaction between the plate and the store. The first-order piston theory is used to describe the aerodynamic load. The governing equation of the composite laminated plate with an external store is established based on the Hamilton principle. The mode shapes are constructed by the admissible functions which axe a set of characteristic orthogonal polynomials generated directly by the Gram-Schmidt process, and the boundary constraint is modeled as the artificial springs. The frequency and mode shapes of the plate under different boundaries are determined by the Rayleigh-Ritz method. The validity of the proposed approach is confirmed by comparing the results with those obtained from the finite element method (FEM). The effects of the mounting position, the center of gravity position and the mounting points spacing of the external store on the flutter boundary are discussed for both the simply supported and cantilever plates, respectively, which correspond to the two installation sites of the external store, i.e., the belly and wings of the aircraft.
文摘A study of postbuckling and delamination propagation behavior in delaminated stiffened composite plates was presented. A methodology was proposed for simulating the multi-failure responses, such as initial and postbuckling, delamination onset and propagation, etc. A finite element analysis was conducted on the basis of the Mindlin first order shear effect theory and the von-Krmn nonlinear deformation assumption. The total energy release rate used as the criteria of delamination growth was estimated with virtual crack closure technique (VCCT). A self-adaptive grid moving technology was adopted to model the delamination growth process. Moreover, the contact effect along delamination front was also considered during the numerical simulation process. By some numerical examples, the influence of distribution and location of stiffener, configuration and size of the delamination, boundary condition and contact effect upon the delamination growth behavior of the stiffened composite plates were investigated. The method and numerical conclusion provided should be of great value to engineers dealing with composite structures.
基金the National Natural Science Foundation of China(No.10572049).
文摘A constitutive model for composite laminated plates with the damage effect of the intra-layers and inter-laminar interface is presented. The model is based on the general six-degrees-of-freedom plate theory, the discontinuity of displacement on the interfaces are depicted by three shape functions, which are formulated according to solutions satisfying three equilibrium equations, By using the variation principle, the three-dimensional non-linear equilibrium differential equations of the laminated plates with two different damage models are derived. Then, considering a simply supported laminated plate with damage, an analytical solution is presented using finite difference method to obtain the inter-laminar stresses.
文摘A general anisotropic damage theory of cracked laminates is formulated here.The deformation of composite laminates is composed of matrix elastic strains,pseudo-elastic damage strains due to cracking and permanent damage strains due to interlaminar slip.The surface of damage initiation is constructed accord- ing to the concept of linear elastic fracture mechanics for the virgin material.After the initial damage,a pesudo-elastic damage can be used to describe the damage behaviour if interlaminar slip is negligible.Damage evolution,load induced anisotropy and interlaminar-intralaminar interaction for composite laminates are exam- ined;the latter can perturb the normality structure of damage strain rate.Explicit expressions are given for pseudo-elastic (or secant) moduli of the damaging composite laminates,under a non-interacting assumption imposed on the cracks between different families.
基金Sponsored by the National Natural Science Foundation of China(Grant No.11272105)the Heilongjiang Province Science Foundation for Youths(Grant No.QC2015003)the Harbin Science and Technology Bureau Young Talent Reserve Project(Grant No.RC2016QN001011,RC2016QN017023)
文摘The testing on the bearing strength of single-shear bolt jointed composite laminates structure is done.And the effect of the fixture on the testing results is analyzed. Then a macro-micro multi-scale analytical model combined with the improved"Generalized Method of Cells( GMC) "is developed,which is used to predict the macro bearing strength and to characterize the micro constitute material failure of the bolt jointed composite laminates structure. Both the contact conditions at the bolt/hole boundary and the contact conditions at the specimen/fixture boundary,progressive damage,and the material properties degradation are all taken account into the analytical model. Thus,the numerical simulation results agree well with the experimental results.Finally,the effect of the fixture on the testing results is characterized. The results show that the incomplete contaction between the fixture and the specimen or the lack of the lateral constraint on the specimen will affect the limited bearing strength and the offset bearing strength of the bolt jointed composite laminates structure. In addition,the lower support rigid of the fixture will affect the rigid of the bolt jointed composite laminates structure.
文摘The study on properly degradation of damaged,.onlj,osile laminates is extendedto anisotropic laminates with matrix cracking. In (II) of the paper, a solution forpartitioned stiffness is given to complete the constitutive relations developed in (I) Thestiffness degradation in cracked laminates is calculated and the results arediscussed.
文摘Effects of layer quantities and stacking sequences on L-shape composite manufacturing qualities in using OOA(out-of-autoclave)prepregs were studied.The mechanisms of air evacuated in 5 kinds of lay-ups were revealed by image analysis of cut surfaces and thickness measurements.Results show that air in OOA prepregs is evacuated in two ways.Most of the air is forced out of layers directly by vacuum before air accesses in prepregs closed.Very little entrapped air moves perpendicularly to outer layers under hydrostatic resin pressure.When a laminate contains less than 16 layers,voids can hardly be found in layers.When a laminate contains more than 16 layers,voids cannot be expelled completely during the window of vertical movement.As for stacking sequences,the synergetic effect of slip function and nest function determines the thickness and voids content of laminates.Results show that the average of single layer thickness of unidirectional layers is the lowest,and the average of single layer thickness of quasi-isotropic layers is the highest.The voids content of quasi isotropic is the highest,which is consistent with the theoretical analysis.
基金supported by the Fundamental Research Funds for the Central Universities [grant nos.DUT21LAB108,DUT22LAB401].
文摘The vibration attenuation and damping characteristics of carbon fiber reinforced composite laminates with different thicknesses were investigated by hammering experiments under free boundary constraints in different directions.The dynamic signal testing and analysis system is applied to collect and analyze the vibration signals of the composite specimens,and combine the self-spectrum analysis and logarithmic decay method to identify the fundamental frequencies of different specimens and calculate the damping ratios of different directions of the specimens.The results showed that the overall stiffness of the specimen increased with the increase of the specimen thickness,and when the thickness of the sample increases from 24mm to 32mm,the fundamental frequency increases by 35.1%,the vibration showed the same vibration attenuation and energy dissipation characteristics in the 0°and 90°directions of the specimen,compared with the specimen in the 45°direction,which was less likely to be excited and had poorer vibration attenuation ability,while the upper and lower surfaces of the same specimen showed slightly different attenuation characteristics to the vibration,the maximum difference of damping capacity between top and bottom surfaces of CFRP plates is about 70%.
基金The project supported by the National Natural Science Foundation of China(10172023)
文摘A new higher-order shear deformation theory based on global-local superposition technique is developed. The theory satisfies the free surface conditions and the geometric and stress continuity conditions at interfaces. The global displacement components are of the Reddy theory and local components are of the internal first to third-order terms in each layer. A two-node beam element based on this theory is proposed. The solutions are compared with 3D-elasticity solutions. Numerical results show that present beam element has higher computational efficiency and higher accuracy.
基金National Natural Science F oundation of China !( No.1980 2 0 0 1)
文摘Fatigue tests of the smooth composite laminates and the notched composite laminates under compressive cyclic loading have been carried out. The damage mechanism is discussed and analyzed. Damage evolution is monitored using stiffness decay. From these tests, it is found that the initial delamination occurs at the free boundary of smooth specimens, or the notch boundary of notched specimens, subjected to the compression-compression cyclic load. A point of view in relation to two-phases of compression fatigue delamination of composites is proposed, namely, compression-compression delamination consists of the delamination formation phase and the delamination propagation, and there is a 'damage transition point' to separate this two-phases. Furthermore, an empirical modulus degradation formula and its parameters fitting method are presented. According to the test data handling results, it is shown that this formula is univocal and can fit the test data conveniently. In addition, two kinds of new anti-buckling devices are designed for these tests. At last, the E-N curves, the D-N curves and the S-N curve of the smooth carbon fiber reinforced composite laminates of T300/648C are determined to predict the fatigue life of the notched composite laminate. And the E-N curve of the notched specimens at the given load ratio R = 10 and minimum load Pmin = -0.45 kN is also measured to verify the estimated result of fatigue life.