Method based on broadband compressed pulse superposition to measure properties of underwater acoustic materials

A method is proposed for the measurements of the performances of underwater acoustic finite sized large area material samples in a free field by using broadband pulse compression technique. As the result of which, the low-frequency cutoff of the standard tests is obviously reduced, and the broadband measurements are also realized. The experimental system provides measurements of complex reflection and transmission coefficients at continuous frequency points. From the data one can obtain the following acoustic parameters: echo reduction and insertion loss, absorption and attenuation coefficients, etc. The measurements are performed for two actual panels with the size 1 m x 1 m in the frequency range from 2-20 kHz.

A novel power-combination method using a time-reversal pulse-compression technique

The electromagnetic time-reversal(TR)technique has the characteristics of spatiotemporal focusing in a time-reversal cavity(TRC),which can be used for pulse compression,thus forming an electromagnetic pulse with high peak power.A time-reversed pulse-compression method in a single channel has high pulse compression gain.However,single channel pulse compression can only generate limited gain.This paper proposes a novel TR power-combination method in a multichannel TRC to obtain higher peak power based on TR pulse-compression theory.First,the TR power-combination model is given,and the crosstalk properties of the associated channel and the influence of the reversal performance are studied.Then,the power-combination performances for the TR pulse compression,such as combined signal to noise ratio(SNR)and combined compression gain,are analyzed by numerical simulation and experimental methods.The results show that the proposed method has obvious advantages over pulse-compression methods using a single channel cavity,and is more convenient for power combination.

Research on the imaging of concrete defect based on the pulse compression technique

When the synthetic aperture focusing technology （SAFT） is used for the detection of the concrete, the signal-to-noise ratio （SNR） and detection depth are not satisfactory. Therefore, the application of SAFT is usually limited. In this paper, we propose an improved SAFT technique for the detection of concrete based on the pulse compression technique used in the Radar domain. The proposed method first transmits a linear frequency modulation （LFM） signal, and then compresses the echo signal using the matched filtering method, after which a compressed signal with a narrower main lobe and higher SNR is obtained. With our improved SAFT, the compressed signals are manipulated in the imaging process and the image contrast is improved. Results show that the SNR is improved and the imaging resolution is guaranteed compared with the conventional short-pulse method. From theoretical and experimental results, we show that the proposed method can suppress noise and improve imaging contrast, and can also be used to detect multiple defects in concrete.

Lorentz force electrical impedance tomography using pulse compression technique

Lorentz force electrical impedance tomography （LFEIT） combines ultrasound stimulation and electromagnetic field detection with the goal of creating a high contrast and high resolution hybrid imaging modality. In this study, pulse compression working together with a linearly frequency modulated ultrasound pulse was investigated in LFEIT. Experiments were done on agar phantoms having the same level of electrical conductivity as soft biological tissues. The results showed that：（i） LFEIT using pulse compression could detect the location of the electrical conductivity variations precisely; （ii） LFEIT using pulse compression could get the same performance of detecting electrical conductivity variations as the traditional LFEIT using high voltage narrow pulse but reduce the peak stimulating power to the transducer by 25.5 dB; （iii） axial resolution of 1 mm could be obtained using modulation frequency bandwidth 2 MHz.

Femtosecond electron pulse compression by using the time focusing technique in ultrafast electron diffraction

We present a new model of an electron gun for generating subrelativistic femtosecond （fs） electron pulses. The basic idea is to utilize a dc acceleration stage combined with a time focusing region, the time focusing electrode generates an electron energy chirp for bunching at the target. Without considering the space charge effects, simulations of the electron gun were carried out under the conditions of different dc voltages and various slopes of the voltage added on the time focusing electrode. Tracing and simulating large numbers of photoelectrons through Monte-Carlo and finite difference methods, the electron pulses with 1 ps can be compressed to 55 fs, which will allow significant advances in the field of ultrafast diagnosis.

NEW TYPE OF WINDOWS FOR DIGITAL PULSE COMPRESSION IN FREQUENCY DOMAIN FOR BROADBAND LFM SIGNALS

A new type of window called combined window is designed to get higher Ratio of Mainlobe to Sidelobes (RMS) and lower Mainlobe Widening Factor (MWF). Simulation results prove that the new window can solve the contradiction between RMS and MWF better than classic windows.

ASIC Design and Implementation for Digital Pulse Compression Chip

A novel ASIC design of changeable-point digital pulse compression (DPC) chip is presented. System hardware resource is reduced to one third of the traditional design method through operations sharing hardware, (i.e.) let FFT, complex multiplication and IFFT be fulfilled with the same hardware structure. Block-floating-point scaling is used to enhance the dynamic range and computation accuracy. This design applies parallel pipeline structure and the radix-4 butterfly operation to improve the processing speed. In addition, a triple-memory-space(TMS) configuration is used that allows input, computation and output operations to be overlapped, so that the dual-butterfly unit is never left in an idle state waiting for I/O operation. The whole design is implemented with only one chip of XC2V500-5 FPGA. It can implement 1 024-point DPC within 91 6 μs.The output data is converted to floating-point formation to achieve seamless interface with TMS320C6701. The validity of the design is verified by simulation and measurement results.

Optical Pulse Compression Based on High-doped Erbium Fiber Amplifier and Standard Single-mode Fiber

Proposed is a novel optical pulse compression technique based on high-doped erbium fiber amplifier and standard single-mode fiber(SMF). We used the amplifier with the erbium ion concentration of 6.3×10-3 to amplify a hyperbolic secant pulse from a regeneratively mode-locked fiber laser. The central wavelength, pulsewidth and peak power of the pulse are 1 550 nm, 12.5 ps and 3 mW, respectively. Then the amplified pulse with peak power level corresponding to a higher-order soliton is compressed when it propagates through a 3-km-long single-mode fiber. Studied are the compressed pulses under different pump powers and fiber lengths. The results show that it can get a narrower pulse, and solve the difficulty that pulses at low power can not be compressed directly in the fiber. And the construct is compact.

Generation of few-cycle radially-polarized infrared pulses in a gas-filled hollow-core fiber

We perform a numerical study for temporally compressing radially-polarized（RP） infrared pulses in a gas-filled hollow-core fiber（HCF）. The dynamic transmission and nonlinear compression of RP pulses centered at wavelengths of0.8 m, 1.8 m, 3.1 m, and 5.0 m in HCFs are simulated. By comparing the propagation of pulses with the same optical cycles and intensity, we find that under proper conditions these pulses can be compressed down to 2–3 cycles. In the transverse direction, the spatiotemporal beam profile ameliorates from 0.8-m to 1.8-m and 3.1-m pulses before the appearance of high-order dispersion. These results show an alternative method of scaling generation for delivering RP infrared pulses in gas-filled HCFs, which can obtain energetic few-cycle pulses, and will be beneficial for relevant researches in the infrared scope.

Pulse Compression Technique of Radio Fuze

The advantages of using phase-coded pulse compression technique for radio fuze systems are evaluated. With building mathematical models a matched filter has been implemented successfully. Various simulations for pulse compression waveform coding were done to evaluate the performance of fuze system under noisy environment. The results of the simulation and the data analysis show that the phase-coded pulse compression gets a good result in the signal identification of the radio fuze with matched filter. Simultaneously, a suitable sidelobe suppression filter is established by simulation, the suppressed sidelobe level is acceptable to radio fuze application.

Study on pulse compression in tapered holey fibres

This paper proposes three kinds of tapered holey fibres with a multi-layer of holes whose pitch of air holes at the end of untapered and tapered are 5.8 μm and 1.8 μm. The central wavelength which locates in the anomalous dispersion region is 1.55 μm. An adaptive split-step Fourier method is numerically used to study the pulse propagation in tapered holey fibres. For the considered convex tapered holey fibre, at a wavelength of 1.55 μm, a compression factor of 136.7 can be achieved by initial width of 800 fs propagation through a length of 0.8 m. It demonstrates that in anomalous dispersion region, pulse can be compressed with the increase of nonlinearity coefficient and the decrease of dispersion coefficient.

APULSECOMPRESSORIMPLEMENTATIONWITHDSPFORSMALLTBPRODUCTLFMWAVEFORM

This paper describes a pulse compressor implementation with DSP for small Time Bandwidth (TB) product Linear Frequency Modulation (LFM) waveform. It contains the digital generation of the LFM waveform and the digital internally Hamming weighted compression filter. Two methods for suppression of time sidelobe of the digital pulse compressor are employed. First, the LFM waveform is modified by using cubic phase pre distortion for reducing the effect of Fresnel ripples in small TB product LFM waveform. Secondly, anti aliasing filter is used before A/D converter for reducing spectrum skirt level of the returned LFM waveform. The parameters of the compression filter implemented with IMSA100 DSP are programmable. The experiments show that the peak time sidelobe level of the digital pulse compressor is less than -32 dB for TB product of 20.

Compressing ultrafast electron pulse by radio frequency cavity

An ultrafast electron diffraction technique with both high temporal and spatial resolution has been shown to be a powerful tool to observe the material transient structural change on an atomic scale.The space charge forces in a multi-electron bunch will greatly broaden the electron pulse width,and therefore limit the temporal resolution of the high brightness electron pulse.Here in this work,we design an ultrafast electron diffraction system,and utilize a radio frequency cavity to realize the ultrafast electron pulse compression.We experimentally demonstrate that the stretched electron pulse width of14.98 ps with an electron energy of 40 keV and the electron number of 1.0 ×10;can be maximally compressed to about0.61 ps for single-pulse measurement and 2.48 ps for multi-pulse measurement by using a 3.2-GHz radiofrequency cavity.We also theoretically and experimentally analyze the parameters influencing the electron pulse compression efficiency for single-and multi-pulse measurements by considering radiofrequency field time jitter,electron pulse time jitter and their relative time jitter.We suggest that increasing the electron energy or shortening the distance between the compression cavity and the streak cavity can further improve the electron pulse compression efficiency.These experimental and theoretical results are very helpful for designing the ultrafast electron diffraction experiment equipment and compressing the ultrafast electron pulse width in a future study.

Analysis and Improvement of the Real-Time Segmented Pulse Compression-Detection Algorithm

Real-Time segmented pulse compression-detection is one of the key technologies of space-borne tracking receiver. Its implementation requires an optimized and dedicated hardware. The real-time processing places several constraints such as area occupied, power comumption, and speed. A number of segmented compression techniques have been proposed to overcome these limitations and decrease the processing latency. However, relatively high power loss in the partial field could limit their implementation in many current real-time systems. A good theoretical model was designed with intersection signal accumulation to enhance signal- noise-ratio （SNR） gain of detecting signal in the paper. From the experimental results it is known that this approach works well for pulse compression-detection, which is better suited for implementation in the high performance of current field programmable gate array （FPGA） with dedicated hardware multipliers.

A UWB communication system based on dechirp pulse compression and OOK modulation

In this paper,a novel UWB communication system structure is proposed.The transmitted signal uses OOK modulation and chirp spread spectrum.The received signal first goes through a dechirp pulse compression process,and then is processed with a two-level sliding correlation algorithm for coarse timing synchronization and fine timing synchronization.After the SNR estimation,the signal is demodulated by an energy detection method.An integrated system level simulation model is established,and the performance of this system is evaluated over the AWGN channel,IEEE 802.15.3a CM1 and CM4 channels.The theoretical analysis and simulation results show that this UWB communication system can effectively reduce the sampling rate and signal processing speed at the receiver,and it is more suitable for long-distance and low-rate UWB communications with high spreading gain.

Generation of few-cycle laser pulses:Comparison between atomic and molecular gases in a hollow-core fiber

We numerically study the pulse compression approaches based on atomic or molecular gases in a hollow-core fiber.From the perspective of self-phase modulation（SPM）, we give the extensive study of the SPM influence on a probe pulse with molecular phase modulation（MPM） effect. By comparing the two compression methods, we summarize their advantages and drawbacks to obtain the few-cycle pulses with micro- or millijoule energies. It is also shown that the double pump-probe approach can be used as a tunable dual-color source by adjusting the time delay between pump and probe pulses to proper values.

Specifications and control of spatial frequency errors of components in two-beam laser static holographic exposure for pulse compression grating fabrication

The large-aperture pulse compression grating(PCG) is a critical component in generating an ultra-high-intensity, ultra-short-pulse laser;however, the size of the PCG manufactured by transmission holographic exposure is limited to large-scale high-quality materials. The reflective method is a potential way for solving the size limitation, but there is still no successful precedent due to the lack of scientific specifications and advanced processing technology of exposure mirrors. In this paper, an analytical model is developed to clarify the specifications of components, and advanced processing technology is adopted to control the spatial frequency errors. Hereafter, we have successfully fabricated a multilayer dielectric grating of 200 mm × 150 mm by using an off-axis reflective exposure system with Φ300 mm. This demonstration proves that PCGs can be manufactured by using the reflection holographic exposure method and shows the potential for manufacturing the meter-level gratings used in 100 petawatt class high-power lasers.

Study of ultra-wideband radar signals-generated technology using two-channel signal generator

Synthesis of ultra-wideband （UWB） linear frequency modulation radar signals is a very important technology for microwave imaging, target identification and detection of low radar-cross-section （RCS） targets. A new method of UWB radar signals generation with two-channel signal generator is presented. The realization structure is given; the principle and errors of signal synthesis are analyzed. At the same time, an automatic .adjustment measure of signal phase is proposed because of phase discontinuity of waveform in this method. The simulation experiment and analysis results indicate that radar signals with large instantaneous bandwidth can be generated by means of this method on the condition that the high-speed digital devices are limited.

A Ka-band Solid-state Transmitter Cloud Radar and Data Merging Algorithm for Its Measurements

This study concerns a Ka-band solid-state transmitter cloud radar, made in China, which can operate in three different work modes, with different pulse widths, and coherent and incoherent integration numbers, to meet the requirements for cloud remote sensing over the Tibetan Plateau. Specifically, the design of the three operational modes of the radar（i.e., boundary mode M1, cirrus mode M2, and precipitation mode M3） is introduced. Also, a cloud radar data merging algorithm for the three modes is proposed. Using one month＇s continuous measurements during summertime at Naqu on the Tibetan Plateau,we analyzed the consistency between the cloud radar measurements of the three modes. The number of occurrences of radar detections of hydrometeors and the percentage contributions of the different modes＇ data to the merged data were estimated.The performance of the merging algorithm was evaluated. The results indicated that the minimum detectable reflectivity for each mode was consistent with theoretical results. Merged data provided measurements with a minimum reflectivity of -35 dBZ at the height of 5 km, and obtained information above the height of 0.2 km. Measurements of radial velocity by the three operational modes agreed very well, and systematic errors in measurements of reflectivity were less than 2 dB. However,large discrepancies existed in the measurements of the linear depolarization ratio taken from the different operational modes.The percentage of radar detections of hydrometeors in mid- and high-level clouds increased by 60% through application of pulse compression techniques. In conclusion, the merged data are appropriate for cloud and precipitation studies over the Tibetan Plateau.

Supercontinuum spectra generation in the single-mode optical fibre with concave dispersion profile

In this paper, a new method is proposed to generate broad supercontinuum （SC） spectra in the single-mode optical fibre with concave dispersion profile, We numerically simulate pulse evolutions and discuss physics mechanism in detail for SC spectrum generation in the optical fibre with concave dispersion profile. Furthermore, general criteria are presented for specifying the shape of SC spectrum by introducing normalized parameters, which are related to the fibres and the initial pump pulses. The results show that the flat and broad SC spectra are indeed generated in our proposed optical fibre.