The procedure during complex system plan design of welding position-locating machine is studied in this paper. The main difficulties in designing welding position-locating machine utilizing computer are discussed as w...The procedure during complex system plan design of welding position-locating machine is studied in this paper. The main difficulties in designing welding position-locating machine utilizing computer are discussed as well. A method of case-based intelligent CAD system for welding position-locating machine ( WMICAD) is put forward through wide research on design methodology. Object-oriented programming method is also applied to Ms system. The basic idea and realizing method are described.展开更多
Poly Laevo Lactic Acid (PLLA), in spite of being an excellent bioplastic, has exorbitantly high market price due to the high cost of raw material (lactose, glucose, sucrose). Hence, its manufacture is being attempted ...Poly Laevo Lactic Acid (PLLA), in spite of being an excellent bioplastic, has exorbitantly high market price due to the high cost of raw material (lactose, glucose, sucrose). Hence, its manufacture is being attempted starting from waste effluents such as cheese whey and molasses. Earlier studies on the same in fluidized bed and semifluidized bed biofilm reactors yielded encouraging results. The present study therefore involves design and analysis of inverse fluidized bed biofilm reactors for lactic acid synthesis. The performance features of the bioreactor have been studied both mathematically as well as experimentally. The inverse fluidized bed biofilm reactor has been found to provide more than 75% conversion of sucrose/lactose even at high capacities (high feed flow rates) exceeding 56,000 L/hr, within a reasonably low reactor volume. The fractional substrate conversion increases, though sluggishly, with increase in feed flow rate due to bed expansion and also with increase in cell mass concentration in biofilm due to enhancement in intrinsic rate of bioconversion. The inverse fluidized bed biofilm reactor of proposed design could be safely recommended for the commercial synthesis of polymer grade lactic acid from waste effluents such as cheese whey and molasses. The low operating cost of the bioreactor (due to downflow mode of operation) enhances the economy of the process. This would also help in significantly lowering the market price of the green plastic (PLLA) and shall promote its large scale manufacture and utilisation.展开更多
Methods for computer aided design and analysis on color-woven fabrics are presented. The relation of color pattern, colored warp, colored weft and the model for regular weave texture are given based on their formative...Methods for computer aided design and analysis on color-woven fabrics are presented. The relation of color pattern, colored warp, colored weft and the model for regular weave texture are given based on their formative principle. Some efficient algorithms are developed to determine the color order of warp and weft threads which yields a given color pattern and regular weave texture. Finally, the design system structure and data process flowing are introduced.展开更多
The reasonability of cabin layout is studied according to the ergonomic theory on micro-computer. This system includes the anthropometric model,modeling of aircraft seats and cabin,interactive ergonomic analyses on ef...The reasonability of cabin layout is studied according to the ergonomic theory on micro-computer. This system includes the anthropometric model,modeling of aircraft seats and cabin,interactive ergonomic analyses on effect.展开更多
A computer aided design system for developing musical fountain programs was developed with multiple functions such as intelligent design, 3-D animation, manual modification and synchronized motion to make the develop...A computer aided design system for developing musical fountain programs was developed with multiple functions such as intelligent design, 3-D animation, manual modification and synchronized motion to make the development process more efficient. The system first analyzed the music form and sentiment using many basic features of the music to select a basic fountain program. Then, this program is simulated with 3-D animation and modified manually to achieve the desired results. Finally, the program is transformed to a computer control program to control the musical fountain in time with the music. A prototype system for the musical fountain was also developed. It was tested with many styles of music and users were quite satisfied with its performance. By integrating various functions, the proposed computer aided design system for developing musical fountain programs greatly simplified the design of the musical fountain programs.展开更多
Today’s product creative design has rendered many fe atures and has brought a great change in our everyday life, there are many new c hallenges in its traditional theory and principle. According to the traditional de...Today’s product creative design has rendered many fe atures and has brought a great change in our everyday life, there are many new c hallenges in its traditional theory and principle. According to the traditional design theory, the FBS design model pays more attention to the function and stru cture of the product. But this model still couldn’t strengthen the relation bet ween product appearance design and human-machine design effectively. This paper adopt converse design thinking and presents an improved design thinking methodo logy based on C: FBS for product appearance design and give a general summarizat ion for the features, methods and technology based on human-machine interaction and interface. Meanwhile it also combines with the behavior design of product r elated IT fields and constructs a new outline to improve the design of product a ppearance supported by the technology of computer aided design. So the new metho d about design thinking for computer aided design, the new abstract product design model and the key problem of design thinking based on human-machine inte raction and interface are addressed in this paper. This kind of creative design theory that is driven by human-machine interaction and interface will help the development of CAD software system and the research of product design and manufa cture. Additionally, this paper gives some beneficial characters to address the theory based on human-machine interaction and interface. Meanwhile, combining with the developing of computer technology, the trends of design thinking based on t he technology of human-machine interaction and interface are also analyzed and discussed at the end of this paper.展开更多
Some concepts of virtual product are discussed. The key technologies ofvirtual fuel-pump development are in detail analysed, which include virtual fuel-pump productmodeling, intelligent simulation, distributed design ...Some concepts of virtual product are discussed. The key technologies ofvirtual fuel-pump development are in detail analysed, which include virtual fuel-pump productmodeling, intelligent simulation, distributed design environment, and virtual assembly. The virtualfuel-pump development prototype system considers requirement analysis, concept design, injectionpreferment analysis, detailed design, and assembly analysis.展开更多
A scheme for general purposed FDTD visual scientific computing software is introduced in this paper using object-oriented design (OOD) method. By abstracting the parameters of FDTD grids to an individual class and sep...A scheme for general purposed FDTD visual scientific computing software is introduced in this paper using object-oriented design (OOD) method. By abstracting the parameters of FDTD grids to an individual class and separating from the iteration procedure, the visual software can be adapted to more comprehensive computing problems. Real-time gray degree graphic and wave curve of the results can be achieved using DirectX technique. The special difference equation and data structure in dispersive medium are considered, and the peculiarity of parameters in perfectly matched layer are also discussed.展开更多
A new design method for prehminary parameters is proposed. The analyticmodels of the optimization design are established according to the requirements of helicopter flight performance- stability, engine and weight. Th...A new design method for prehminary parameters is proposed. The analyticmodels of the optimization design are established according to the requirements of helicopter flight performance- stability, engine and weight. The optinial preliminary projectof design to meet the requirements of critenon for helicopter design is worked out byapplying the computer and optimization techniques. The inethod can be used for theanalysis of helicopters for prehminary parameters that are used in practice and for theanalysis of sensibility for preliminary parameters, too. The method is shown to be veryuseful by the example and application in the new design of helicopters.展开更多
According to the inland micro electro-mechanical system (MEMS) process technique level, a design platform of piezoresistive micro electro-mechanical accelerometer is given. This platform is much more adaptable to th...According to the inland micro electro-mechanical system (MEMS) process technique level, a design platform of piezoresistive micro electro-mechanical accelerometer is given. This platform is much more adaptable to the inland designer compared with the current MEMS CAD software. The design flow is presented in detail, and the key techique in the platform is analyzed amply. The structure design methodology is exemplified in the design of a piezoresistive accelerometer, and the accelerometer is the optimized structure for the given performance requirements. The accelerometer is now being manufactured.展开更多
<span style="font-family:Verdana;">A creative and/or innovative computer aided design environment is developed around the concept of an evolutionary optimization algorithm. Designs are generated within...<span style="font-family:Verdana;">A creative and/or innovative computer aided design environment is developed around the concept of an evolutionary optimization algorithm. Designs are generated within a set of prescribed design frameworks using a problem specific encoding and modified through operations including recombination, crossover and mutation. Evaluation of all candidate designs is performed by a user through a graphical user interface. A set of problems involving the creation of graphic images is presented. The examples include the generation of a set of two dimensional polygonal shapes, fractal images, path generation from a multi-degree freedom mechanical planar linkage and a mathematically pre</span><span style="font-family:Verdana;">scribed pattern generation from a graphic design application utilized in</span><span style="font-family:Verdana;"> quilting. Post design evaluation of the user input to the process provides insight into the individuals design strategy as well as determination of common user attributes in the creative design process.</span>展开更多
<div style="text-align:justify;"> <span style="font-family:Verdana;">Engineering design is a resource intensive process with over half of a product’s total cost being attributed to des...<div style="text-align:justify;"> <span style="font-family:Verdana;">Engineering design is a resource intensive process with over half of a product’s total cost being attributed to design stage decisions. Developing product designs often involves creating complex 3D models in a 2D environment, a non-trivial task. This paper details a proof of concept VR environment displayed in a commodity HMD, specifically the HTC Vive. The environment allows a user to create full-scale, 3D, product geometry at the conceptual phase of the design process. The conceptual design environment contains a World-in-Miniature (WIM) model for enhanced usability. This method allows a user to efficiently manipulate full-scale geometry by adjusting the corresponding parts on a WIM model. Free-form mesh deformation was also implemented to provide designers with flexibility and efficiency not found in traditional design packages. Vital design metrics (e.g., cost, weight, and center of mass) were incorporated to allow a user to perform preliminary design analysis to assess product feasibility. Throughout the development process, the unique challenges and affordances associated with commodity HMDs were identified, explored, and discussed in this paper. Ultimately, the VR application discussed in this paper allows the user to easily create, assess, and view conceptual 3D designs without the constraints of traditional CAD software.</span> </div>展开更多
This paper presents an advanced computer aided design (CAD) package for the synthesis, analysis, and optimization of synchronous reluctance combined with permanent magnet (SR PM) machines. The distinguishing features...This paper presents an advanced computer aided design (CAD) package for the synthesis, analysis, and optimization of synchronous reluctance combined with permanent magnet (SR PM) machines. The distinguishing features of the CAD package are that it allows a wide range of design options and parameter variations for the new type of machines, calculations of optimization for maximum efficiency and higher power density, and various performance. The package as described in the main text permits the integration of the machine design with an electronic controller, along with the simulation of the whole system. Through the optimal design, characteristic calculations, and system simulations, the CAD package offers a superior design for the SR PM machines, and presents a feasibility frontier outlined by the design.展开更多
BACKGROUND An extra tooth in the normal tooth sequence in any region of the dental arch is regarded as a supernumerary tooth(SNT).Due to the large variation in location and morphology,the extraction of impacted SNTs i...BACKGROUND An extra tooth in the normal tooth sequence in any region of the dental arch is regarded as a supernumerary tooth(SNT).Due to the large variation in location and morphology,the extraction of impacted SNTs is an extensive and complex procedure with high risks of several complications.This report presents a rare case of seven impacted SNTs in the bilateral upper and lower arch that were successfully extracted with the use of digital positioning guide plates.CASE SUMMARY In January 2022,a 21-year-old male was referred to our department with a chief complaint of pain in relation to tooth#36.Clinical examination showed a deep carious lesion with pulpal involvement in tooth#36 and lingual swelling of the bilateral mandibular posterior area.Radiographic examination revealed seven deeply impacted SNTs in the bilateral posterior area and bilateral impacted mandibular third molars.Based on these findings,the patient was diagnosed with bilateral,multiple impacted SNTs and tooth#36 chronic pulpitis.A root canal treatment and an all-ceramic crown restoration for tooth#36 were performed.An individualized digital positioning guide plate was designed by computer-aided design/computer-aided manufacturing technology and cone-beam computed tomography for extraction of the impacted SNTs.During the operation,the digital positioning guide plate allowed rapid positioning and exposure of the SNTs while avoiding adjacent important anatomical structures.At 3-month follow-up,regeneration of bone and soft tissues was visible.CONCLUSION The application of digital positioning guide plates is useful for the individualized and minimalized extraction of impacted supernumerary teeth.展开更多
This research work investigates the use of Artificial Neural Network (ANN) based on models for solving first and second order linear constant coefficient ordinary differential equations with initial conditions. In par...This research work investigates the use of Artificial Neural Network (ANN) based on models for solving first and second order linear constant coefficient ordinary differential equations with initial conditions. In particular, we employ a feed-forward Multilayer Perceptron Neural Network (MLPNN), but bypass the standard back-propagation algorithm for updating the intrinsic weights. A trial solution of the differential equation is written as a sum of two parts. The first part satisfies the initial or boundary conditions and contains no adjustable parameters. The second part involves a feed-forward neural network to be trained to satisfy the differential equation. Numerous works have appeared in recent times regarding the solution of differential equations using ANN, however majority of these employed a single hidden layer perceptron model, incorporating a back-propagation algorithm for weight updation. For the homogeneous case, we assume a solution in exponential form and compute a polynomial approximation using statistical regression. From here we pick the unknown coefficients as the weights from input layer to hidden layer of the associated neural network trial solution. To get the weights from hidden layer to the output layer, we form algebraic equations incorporating the default sign of the differential equations. We then apply the Gaussian Radial Basis function (GRBF) approximation model to achieve our objective. The weights obtained in this manner need not be adjusted. We proceed to develop a Neural Network algorithm using MathCAD software, which enables us to slightly adjust the intrinsic biases. We compare the convergence and the accuracy of our results with analytic solutions, as well as well-known numerical methods and obtain satisfactory results for our example ODE problems.展开更多
A new method for design of turbomachinery blades is presented. The parameters of a compressor blade are created from the Computational Fluid Dynamics (CFD) software CFX-BladeGen, and are inputted to the Computer Aid...A new method for design of turbomachinery blades is presented. The parameters of a compressor blade are created from the Computational Fluid Dynamics (CFD) software CFX-BladeGen, and are inputted to the Computer Aided Design (CAD) software UG for building a curve surface model to create an entity model in UG. The result shows that the blade model is favorable from the entity effect and reflection analysis and the model process is useful for the CAD model creation of turbomachinery blades.展开更多
Modeling is the kernel part of a digital reactor system. As an extensible platformfor reactor conceptual design, it is very important to study modeling technology and develop somekind of tools to speed up preparation ...Modeling is the kernel part of a digital reactor system. As an extensible platformfor reactor conceptual design, it is very important to study modeling technology and develop somekind of tools to speed up preparation of all classical computing models. This paper introducesthe background of the project and basic conception of digital reactor. MCAM is taken as anexample for modeling and its related technologies used are given. It is an interface program forMCNP geometry model developed by FDS team (ASIPP & HUT), and designed to run on windowssystem. MCAM aims at utilizing CAD technology to facilitate creation of MCNP geometry model.There have been two ways for MCAM to utilize CAD technology: (1) Making use of user interfacetechnology in aid of generation of MCNP geometry model; (2) Making use of existing 3D CADmodel to accelerate creation of MCNP geometry model. This paper gives an overview of MCAM'smajor function. At last, several examples are given to demonstrate MCAM's various capabilities.展开更多
After undergoing wireframe modeling, surface modeling and solid modeling, a unified product model, which holds a variety of constraints in engineering, supports design process, and unifies the wire frame, surface mode...After undergoing wireframe modeling, surface modeling and solid modeling, a unified product model, which holds a variety of constraints in engineering, supports design process, and unifies the wire frame, surface modeling, and solid modeling,is a general tendency of modeling technology. A discussion is presented here on how tobuild a unified product model by using the complex method. The concept of complex inalgebraic topology is introduced into the model and a new B-REP representation of thenon-manifold model is given --Identification Edge Structure. Based on it, some basicoperators and high-level operators are built. The model has a rigorous mathematicalbasis, and is flexible and easy to extend, and holds the lamina face, lamina edge andlamina vertex. As a result, the variety of constraints in engineering, such as parametricconstraints, optimization methods, fuzzy constraints, artificial intelligent, etc., can beadded to the system. The model may form the kernel for the implementation of the nextgeneration CAD system --intelligent CAD system.展开更多
In this paper, the variational method combined with Green's function is used to analyze the characteristics of suspended, stripline. The result is in good agreement with references. The design of mm-wave end-coupl...In this paper, the variational method combined with Green's function is used to analyze the characteristics of suspended, stripline. The result is in good agreement with references. The design of mm-wave end-coupled bandpass filter with suspended substrate is discussed. The computer programs for design of suspended stripline and bandpass filter are established.展开更多
文摘The procedure during complex system plan design of welding position-locating machine is studied in this paper. The main difficulties in designing welding position-locating machine utilizing computer are discussed as well. A method of case-based intelligent CAD system for welding position-locating machine ( WMICAD) is put forward through wide research on design methodology. Object-oriented programming method is also applied to Ms system. The basic idea and realizing method are described.
文摘Poly Laevo Lactic Acid (PLLA), in spite of being an excellent bioplastic, has exorbitantly high market price due to the high cost of raw material (lactose, glucose, sucrose). Hence, its manufacture is being attempted starting from waste effluents such as cheese whey and molasses. Earlier studies on the same in fluidized bed and semifluidized bed biofilm reactors yielded encouraging results. The present study therefore involves design and analysis of inverse fluidized bed biofilm reactors for lactic acid synthesis. The performance features of the bioreactor have been studied both mathematically as well as experimentally. The inverse fluidized bed biofilm reactor has been found to provide more than 75% conversion of sucrose/lactose even at high capacities (high feed flow rates) exceeding 56,000 L/hr, within a reasonably low reactor volume. The fractional substrate conversion increases, though sluggishly, with increase in feed flow rate due to bed expansion and also with increase in cell mass concentration in biofilm due to enhancement in intrinsic rate of bioconversion. The inverse fluidized bed biofilm reactor of proposed design could be safely recommended for the commercial synthesis of polymer grade lactic acid from waste effluents such as cheese whey and molasses. The low operating cost of the bioreactor (due to downflow mode of operation) enhances the economy of the process. This would also help in significantly lowering the market price of the green plastic (PLLA) and shall promote its large scale manufacture and utilisation.
文摘Methods for computer aided design and analysis on color-woven fabrics are presented. The relation of color pattern, colored warp, colored weft and the model for regular weave texture are given based on their formative principle. Some efficient algorithms are developed to determine the color order of warp and weft threads which yields a given color pattern and regular weave texture. Finally, the design system structure and data process flowing are introduced.
文摘The reasonability of cabin layout is studied according to the ergonomic theory on micro-computer. This system includes the anthropometric model,modeling of aircraft seats and cabin,interactive ergonomic analyses on effect.
基金Supported by the National Natural Science Foundationof China(No.6 0 174 0 15 ) and the Basic Research Foun-dation of Tsinghua U niversity
文摘A computer aided design system for developing musical fountain programs was developed with multiple functions such as intelligent design, 3-D animation, manual modification and synchronized motion to make the development process more efficient. The system first analyzed the music form and sentiment using many basic features of the music to select a basic fountain program. Then, this program is simulated with 3-D animation and modified manually to achieve the desired results. Finally, the program is transformed to a computer control program to control the musical fountain in time with the music. A prototype system for the musical fountain was also developed. It was tested with many styles of music and users were quite satisfied with its performance. By integrating various functions, the proposed computer aided design system for developing musical fountain programs greatly simplified the design of the musical fountain programs.
文摘Today’s product creative design has rendered many fe atures and has brought a great change in our everyday life, there are many new c hallenges in its traditional theory and principle. According to the traditional design theory, the FBS design model pays more attention to the function and stru cture of the product. But this model still couldn’t strengthen the relation bet ween product appearance design and human-machine design effectively. This paper adopt converse design thinking and presents an improved design thinking methodo logy based on C: FBS for product appearance design and give a general summarizat ion for the features, methods and technology based on human-machine interaction and interface. Meanwhile it also combines with the behavior design of product r elated IT fields and constructs a new outline to improve the design of product a ppearance supported by the technology of computer aided design. So the new metho d about design thinking for computer aided design, the new abstract product design model and the key problem of design thinking based on human-machine inte raction and interface are addressed in this paper. This kind of creative design theory that is driven by human-machine interaction and interface will help the development of CAD software system and the research of product design and manufa cture. Additionally, this paper gives some beneficial characters to address the theory based on human-machine interaction and interface. Meanwhile, combining with the developing of computer technology, the trends of design thinking based on t he technology of human-machine interaction and interface are also analyzed and discussed at the end of this paper.
基金National Natural Science Founda-tion of China (No. 59889505).
文摘Some concepts of virtual product are discussed. The key technologies ofvirtual fuel-pump development are in detail analysed, which include virtual fuel-pump productmodeling, intelligent simulation, distributed design environment, and virtual assembly. The virtualfuel-pump development prototype system considers requirement analysis, concept design, injectionpreferment analysis, detailed design, and assembly analysis.
基金This project was supported by the National Natural Science Foundation (No. 69831020).
文摘A scheme for general purposed FDTD visual scientific computing software is introduced in this paper using object-oriented design (OOD) method. By abstracting the parameters of FDTD grids to an individual class and separating from the iteration procedure, the visual software can be adapted to more comprehensive computing problems. Real-time gray degree graphic and wave curve of the results can be achieved using DirectX technique. The special difference equation and data structure in dispersive medium are considered, and the peculiarity of parameters in perfectly matched layer are also discussed.
文摘A new design method for prehminary parameters is proposed. The analyticmodels of the optimization design are established according to the requirements of helicopter flight performance- stability, engine and weight. The optinial preliminary projectof design to meet the requirements of critenon for helicopter design is worked out byapplying the computer and optimization techniques. The inethod can be used for theanalysis of helicopters for prehminary parameters that are used in practice and for theanalysis of sensibility for preliminary parameters, too. The method is shown to be veryuseful by the example and application in the new design of helicopters.
文摘According to the inland micro electro-mechanical system (MEMS) process technique level, a design platform of piezoresistive micro electro-mechanical accelerometer is given. This platform is much more adaptable to the inland designer compared with the current MEMS CAD software. The design flow is presented in detail, and the key techique in the platform is analyzed amply. The structure design methodology is exemplified in the design of a piezoresistive accelerometer, and the accelerometer is the optimized structure for the given performance requirements. The accelerometer is now being manufactured.
文摘<span style="font-family:Verdana;">A creative and/or innovative computer aided design environment is developed around the concept of an evolutionary optimization algorithm. Designs are generated within a set of prescribed design frameworks using a problem specific encoding and modified through operations including recombination, crossover and mutation. Evaluation of all candidate designs is performed by a user through a graphical user interface. A set of problems involving the creation of graphic images is presented. The examples include the generation of a set of two dimensional polygonal shapes, fractal images, path generation from a multi-degree freedom mechanical planar linkage and a mathematically pre</span><span style="font-family:Verdana;">scribed pattern generation from a graphic design application utilized in</span><span style="font-family:Verdana;"> quilting. Post design evaluation of the user input to the process provides insight into the individuals design strategy as well as determination of common user attributes in the creative design process.</span>
文摘<div style="text-align:justify;"> <span style="font-family:Verdana;">Engineering design is a resource intensive process with over half of a product’s total cost being attributed to design stage decisions. Developing product designs often involves creating complex 3D models in a 2D environment, a non-trivial task. This paper details a proof of concept VR environment displayed in a commodity HMD, specifically the HTC Vive. The environment allows a user to create full-scale, 3D, product geometry at the conceptual phase of the design process. The conceptual design environment contains a World-in-Miniature (WIM) model for enhanced usability. This method allows a user to efficiently manipulate full-scale geometry by adjusting the corresponding parts on a WIM model. Free-form mesh deformation was also implemented to provide designers with flexibility and efficiency not found in traditional design packages. Vital design metrics (e.g., cost, weight, and center of mass) were incorporated to allow a user to perform preliminary design analysis to assess product feasibility. Throughout the development process, the unique challenges and affordances associated with commodity HMDs were identified, explored, and discussed in this paper. Ultimately, the VR application discussed in this paper allows the user to easily create, assess, and view conceptual 3D designs without the constraints of traditional CAD software.</span> </div>
文摘This paper presents an advanced computer aided design (CAD) package for the synthesis, analysis, and optimization of synchronous reluctance combined with permanent magnet (SR PM) machines. The distinguishing features of the CAD package are that it allows a wide range of design options and parameter variations for the new type of machines, calculations of optimization for maximum efficiency and higher power density, and various performance. The package as described in the main text permits the integration of the machine design with an electronic controller, along with the simulation of the whole system. Through the optimal design, characteristic calculations, and system simulations, the CAD package offers a superior design for the SR PM machines, and presents a feasibility frontier outlined by the design.
基金Supported by National Natural Science Foundation of China,No.81970972Applied Basic Research Projects of the 920th Hospital of Joint Logistics Support Force,No.2020YGB06。
文摘BACKGROUND An extra tooth in the normal tooth sequence in any region of the dental arch is regarded as a supernumerary tooth(SNT).Due to the large variation in location and morphology,the extraction of impacted SNTs is an extensive and complex procedure with high risks of several complications.This report presents a rare case of seven impacted SNTs in the bilateral upper and lower arch that were successfully extracted with the use of digital positioning guide plates.CASE SUMMARY In January 2022,a 21-year-old male was referred to our department with a chief complaint of pain in relation to tooth#36.Clinical examination showed a deep carious lesion with pulpal involvement in tooth#36 and lingual swelling of the bilateral mandibular posterior area.Radiographic examination revealed seven deeply impacted SNTs in the bilateral posterior area and bilateral impacted mandibular third molars.Based on these findings,the patient was diagnosed with bilateral,multiple impacted SNTs and tooth#36 chronic pulpitis.A root canal treatment and an all-ceramic crown restoration for tooth#36 were performed.An individualized digital positioning guide plate was designed by computer-aided design/computer-aided manufacturing technology and cone-beam computed tomography for extraction of the impacted SNTs.During the operation,the digital positioning guide plate allowed rapid positioning and exposure of the SNTs while avoiding adjacent important anatomical structures.At 3-month follow-up,regeneration of bone and soft tissues was visible.CONCLUSION The application of digital positioning guide plates is useful for the individualized and minimalized extraction of impacted supernumerary teeth.
文摘This research work investigates the use of Artificial Neural Network (ANN) based on models for solving first and second order linear constant coefficient ordinary differential equations with initial conditions. In particular, we employ a feed-forward Multilayer Perceptron Neural Network (MLPNN), but bypass the standard back-propagation algorithm for updating the intrinsic weights. A trial solution of the differential equation is written as a sum of two parts. The first part satisfies the initial or boundary conditions and contains no adjustable parameters. The second part involves a feed-forward neural network to be trained to satisfy the differential equation. Numerous works have appeared in recent times regarding the solution of differential equations using ANN, however majority of these employed a single hidden layer perceptron model, incorporating a back-propagation algorithm for weight updation. For the homogeneous case, we assume a solution in exponential form and compute a polynomial approximation using statistical regression. From here we pick the unknown coefficients as the weights from input layer to hidden layer of the associated neural network trial solution. To get the weights from hidden layer to the output layer, we form algebraic equations incorporating the default sign of the differential equations. We then apply the Gaussian Radial Basis function (GRBF) approximation model to achieve our objective. The weights obtained in this manner need not be adjusted. We proceed to develop a Neural Network algorithm using MathCAD software, which enables us to slightly adjust the intrinsic biases. We compare the convergence and the accuracy of our results with analytic solutions, as well as well-known numerical methods and obtain satisfactory results for our example ODE problems.
文摘A new method for design of turbomachinery blades is presented. The parameters of a compressor blade are created from the Computational Fluid Dynamics (CFD) software CFX-BladeGen, and are inputted to the Computer Aided Design (CAD) software UG for building a curve surface model to create an entity model in UG. The result shows that the blade model is favorable from the entity effect and reflection analysis and the model process is useful for the CAD model creation of turbomachinery blades.
基金The project supported by Centurial Project ("Bai-Ren-Ji-Hua" Project) of Chinese Academy of Sciences. And supported by NSFC (No. 60273044) and NSF of Anhui Province (No. 01042201)
文摘Modeling is the kernel part of a digital reactor system. As an extensible platformfor reactor conceptual design, it is very important to study modeling technology and develop somekind of tools to speed up preparation of all classical computing models. This paper introducesthe background of the project and basic conception of digital reactor. MCAM is taken as anexample for modeling and its related technologies used are given. It is an interface program forMCNP geometry model developed by FDS team (ASIPP & HUT), and designed to run on windowssystem. MCAM aims at utilizing CAD technology to facilitate creation of MCNP geometry model.There have been two ways for MCAM to utilize CAD technology: (1) Making use of user interfacetechnology in aid of generation of MCNP geometry model; (2) Making use of existing 3D CADmodel to accelerate creation of MCNP geometry model. This paper gives an overview of MCAM'smajor function. At last, several examples are given to demonstrate MCAM's various capabilities.
文摘After undergoing wireframe modeling, surface modeling and solid modeling, a unified product model, which holds a variety of constraints in engineering, supports design process, and unifies the wire frame, surface modeling, and solid modeling,is a general tendency of modeling technology. A discussion is presented here on how tobuild a unified product model by using the complex method. The concept of complex inalgebraic topology is introduced into the model and a new B-REP representation of thenon-manifold model is given --Identification Edge Structure. Based on it, some basicoperators and high-level operators are built. The model has a rigorous mathematicalbasis, and is flexible and easy to extend, and holds the lamina face, lamina edge andlamina vertex. As a result, the variety of constraints in engineering, such as parametricconstraints, optimization methods, fuzzy constraints, artificial intelligent, etc., can beadded to the system. The model may form the kernel for the implementation of the nextgeneration CAD system --intelligent CAD system.
文摘In this paper, the variational method combined with Green's function is used to analyze the characteristics of suspended, stripline. The result is in good agreement with references. The design of mm-wave end-coupled bandpass filter with suspended substrate is discussed. The computer programs for design of suspended stripline and bandpass filter are established.