The concept of control system of acceptable gap in the entrance ramp, the construction of the minimum acceptable gap and the method of determining it are introduced. On the above-mentioned basis and by taking the Chin...The concept of control system of acceptable gap in the entrance ramp, the construction of the minimum acceptable gap and the method of determining it are introduced. On the above-mentioned basis and by taking the Chinas reality into consideration, the issues on the design of control system of acceptable gap are approached in this paper.展开更多
A one dimensional model is developed for defective gap mode(DGM)with two types of boundary conditions:conducting mesh and conducting sleeve.For a periodically modulated system without defect,the normalized width of...A one dimensional model is developed for defective gap mode(DGM)with two types of boundary conditions:conducting mesh and conducting sleeve.For a periodically modulated system without defect,the normalized width of spectral gaps equals to the modulation factor,which is consistent with previous studies.For a periodic system with local defects introduced by the boundary conditions,it shows that the conducting-mesh-induced DGM is always well confined by spectral gaps while the conducting-sleeve-induced DGM is not.The defect location can be a useful tool to dynamically control the frequency and spatial periodicity of DGM inside spectral gaps.This controllability can be potentially applied to the interaction between gap eigenmodes and energetic particles in fusion plasmas,and optical microcavities and waveguides in photonic crystals.展开更多
In micro-electrochemical machining(μECM), material dissolution takes place at very close vicinity of tool electrode due to localization of electric field. Controlling the gap between tool electrode and workpiece is t...In micro-electrochemical machining(μECM), material dissolution takes place at very close vicinity of tool electrode due to localization of electric field. Controlling the gap between tool electrode and workpiece is the key to μECM. Therefore, a new method is proposed to solve a variety of problems in small gap control. In the present context, experiments were carried out with an indigenously developed setup to fabricate cylindrical arrays. During the machining process, the flat electrode bends due to electrostatic force in pulse on-time, which self-adaptively narrows the gap between the electrode and the workpiece. The workpiece material will be removed once the gap meets the processing condition. Therefore, this method has advantages of reducing dependence on high precision machine tools and of avoiding complex servo control. The flat electrode quickly restores to its original condition when it is in pulse off-time, making the gap much larger than that in traditional electrochemical machining(ECM). The large gap benefits debris removing, which improves the machining accuracy. The influence of different experimental parameters on accuracy and efficiency during the machining process has been investigated. It is observed that with the increase in applied voltage or concentration of electrolyte, the material removal rate and the process gap both increase. The detailed analysis of the experimental results is described in this paper.展开更多
Background High energy photon source(HEPS)is the fourth-generation light source,which uses a large number of highperformance insertion devices to generate synchrotron radiation.The control system is an important part ...Background High energy photon source(HEPS)is the fourth-generation light source,which uses a large number of highperformance insertion devices to generate synchrotron radiation.The control system is an important part of the insertion device(ID).Purpose Cryogenic permanent magnet undulator(CPMU)is one kind of IDs that works in liquid nitrogen temperature and ultra-high vacuum environment,and its control system is more difficult and complex than in-air ID.The design of the control system for CPMU will be introduced in detail.Method The sub-systems include high-precision magnetic gap control,safety protection,measurement and compensation of magnetic gap at cryogenic temperature and cryogenic temperature monitoring.Mature,reliable,stable technical schemes are designed to meet the technical specifications of sub-systems.Results The experiment results show that the magnetic gap motion accuracy can be controlled within 0.2–0.3μm under the step size of 1μm.The safety protection system has been tested in turn,and the predetermined protection can be achieved.The average value of magnetic gap cold contraction is 1.512 mm measured by optical micrometer,and the compensation is realized by software.The average temperature of the main magnet structure measured by the temperature sensors is 81.0 K,and the temperature gradient is 0.7 K/m.The temperature monitoring is reliable and stable.Conclusion The CPMU control system which is based on EPICS has been successfully applied to the CPMU prototype,and the test results have met the design specifications.展开更多
文摘The concept of control system of acceptable gap in the entrance ramp, the construction of the minimum acceptable gap and the method of determining it are introduced. On the above-mentioned basis and by taking the Chinas reality into consideration, the issues on the design of control system of acceptable gap are approached in this paper.
基金supported by National Natural Science Foundation of China(No.11405271)
文摘A one dimensional model is developed for defective gap mode(DGM)with two types of boundary conditions:conducting mesh and conducting sleeve.For a periodically modulated system without defect,the normalized width of spectral gaps equals to the modulation factor,which is consistent with previous studies.For a periodic system with local defects introduced by the boundary conditions,it shows that the conducting-mesh-induced DGM is always well confined by spectral gaps while the conducting-sleeve-induced DGM is not.The defect location can be a useful tool to dynamically control the frequency and spatial periodicity of DGM inside spectral gaps.This controllability can be potentially applied to the interaction between gap eigenmodes and energetic particles in fusion plasmas,and optical microcavities and waveguides in photonic crystals.
基金supported by the National Natural Science Foundation of China(Grant No.51105110,51475107)Shenzhen Basic Research Program(Grant No.JCYJ20170811160440239)
文摘In micro-electrochemical machining(μECM), material dissolution takes place at very close vicinity of tool electrode due to localization of electric field. Controlling the gap between tool electrode and workpiece is the key to μECM. Therefore, a new method is proposed to solve a variety of problems in small gap control. In the present context, experiments were carried out with an indigenously developed setup to fabricate cylindrical arrays. During the machining process, the flat electrode bends due to electrostatic force in pulse on-time, which self-adaptively narrows the gap between the electrode and the workpiece. The workpiece material will be removed once the gap meets the processing condition. Therefore, this method has advantages of reducing dependence on high precision machine tools and of avoiding complex servo control. The flat electrode quickly restores to its original condition when it is in pulse off-time, making the gap much larger than that in traditional electrochemical machining(ECM). The large gap benefits debris removing, which improves the machining accuracy. The influence of different experimental parameters on accuracy and efficiency during the machining process has been investigated. It is observed that with the increase in applied voltage or concentration of electrolyte, the material removal rate and the process gap both increase. The detailed analysis of the experimental results is described in this paper.
文摘Background High energy photon source(HEPS)is the fourth-generation light source,which uses a large number of highperformance insertion devices to generate synchrotron radiation.The control system is an important part of the insertion device(ID).Purpose Cryogenic permanent magnet undulator(CPMU)is one kind of IDs that works in liquid nitrogen temperature and ultra-high vacuum environment,and its control system is more difficult and complex than in-air ID.The design of the control system for CPMU will be introduced in detail.Method The sub-systems include high-precision magnetic gap control,safety protection,measurement and compensation of magnetic gap at cryogenic temperature and cryogenic temperature monitoring.Mature,reliable,stable technical schemes are designed to meet the technical specifications of sub-systems.Results The experiment results show that the magnetic gap motion accuracy can be controlled within 0.2–0.3μm under the step size of 1μm.The safety protection system has been tested in turn,and the predetermined protection can be achieved.The average value of magnetic gap cold contraction is 1.512 mm measured by optical micrometer,and the compensation is realized by software.The average temperature of the main magnet structure measured by the temperature sensors is 81.0 K,and the temperature gradient is 0.7 K/m.The temperature monitoring is reliable and stable.Conclusion The CPMU control system which is based on EPICS has been successfully applied to the CPMU prototype,and the test results have met the design specifications.