Effect of water content on corrosion inhibition behavior of self-assembled TDPA on aluminum alloy surface

Self assembled monolayers （SAMs） of 1-tetradecylphosphonic acids （TDPA, CH3（CH2）13P（O）（OH）2 ） were formed on the 2024 aluminum alloy surface in TDPA-containing ethanol-water solutions with different water content. The adsorption and corrosion protection properties of the SAMs for 2024 alloy in 0.1 mol/L H2SO4 solution were examined and characterized by potentiodynamic polarization, electrochemical impedance spectrum （EIS）, Fourier transformed infrared spectroscopy （FTIR）, Auger electron spectra （AES） and atomic force microscopy （AFM）. FTIR and AES results show that the TDPA molecules were successfully adsorbed on the 2024 aluminum alloy surface, and the density of the SAMs increased with the increasing water content in the assembly solution. The results of electrochemical studies and corrosion morphologies observed by AFM show that a 4 h modification resulted in maximal inhibition efficiency, and the higher the water content in the assembly solution is, the better the inhibition performance of the SAMs can be achieved. The effect of water content in TDPA solutions on the performance of the SAMs is related to the hydration reaction of the metal surface.

Preparation and characterization of a chitosan-based low-pH-sensitive intelligent corrosion inhibitor

A chitosan （CS）-based low-pH-sensitive intelligent corrosion inhibitor was prepared by loading a pH-sensitive hydrogel with benzotriazole （BTA）; the pH-sensitive hydrogel was synthetized by crosslinking CS with glutaraldehyde （GTA）. Analysis by Fou- tier-transform inflared （FT-IR） spectroscopy showed that Schiff reactions occurred between amino and aldehyde groups. The swelling abil- ity of the hydrogel was investigated using a mass method, and it was observed to swell more in an acidic environment than in an alkaline en- vironment. The hydrogel＇s loading capacity of BTA was approximately 0.377 g·g ^-1, and its release speed was faster in an acidic environment than in an alkaline environment because of its swelling behavior. The corrosion inhibition ability of the intelligent inhibitor was tested by immersion and electrochemical methods. The results showed that after 4 h of immersion, the polarization resistance （Rp） value of copper with the intelligent inhibitor was approximately twice of that of copper with BTA, indicating that the intelligent inhibitor could effectively prevent copper from corroding.

Corrosion Inhibition of a Green Scale Inhibitor Polyepoxysuccinic Acid

The corrosion inhibition of a green scale inhibitor, polyepoxysuccinic acid (PESA) was studied based on dynamic tests. It is found that when PESA is used alone, it had good corrosion inhibition. So, PESA should be included in the category of corrosion inhibitors. It is not only a kind of green scale inhibitor, but also a green corrosion inhibitor. The synergistic effect between PESA and Zn2+ or sodium gluconate is poor. However, the synergistic effect among PESA, Zn2+ and sodium gluconate is excellent, and the corrosion inhibition efficiency for carbon steel is higher than 99%. Further study of corrosion inhibition mechanism reveals that corrosion inhibition of PESA is not affected by carboxyl group, but by the oxygen atom inserted. The existence of oxygen atom in PESA molecular structure makes it easy to form stable chelate with pentacyclic structure.

Corrosion Inhibition Synergism between Lanthanum(Ⅲ) Ion and 8-Hydroxyquinoline for Zinc in Hydrochloric Acid

The effects of La 3+ ion and chelate reagent 8 hydroxyquinoline on the corrosion rate of zinc in hydrochloric acid were investigated by using weight loss method and electrochemical method. It is found that in a specific concentration range of La 3+ ion and 8 hydroxyquinoline, the obvious corrosion inhibition synergism is obtained. The mechanism of corrosion inhibition synergism was discussed on basis of adsorption theory.

ELECTROCHEMICAL IMPEDANCE SPECTROSCOPY STUDY OF CORROSION INHIBITION OF MODIFIED LIGNOSULPHONATE FOR CARBON STEEL

The corrosion inhibition for carbon steel in circulating cooling water by modified lignosulphonate has been investigated using electrochemical impedance spectroscopy technique. Results show that the inhibition efficiency of modified lignosulphonate GCL2 is a great improvement on that of lignosulphonate. The maximum inhibition efficiency of GCL2 reaches 99.21% at the concentration of 400mg·L^-1 at 303K. The corrosion inhibition of GCL2 is attributed to forming adsorption film on the metal surface for the electrochemical impedance spectroscopy in GCL2 solution shows more than one time-constant.Moreover,results also indicate that it is more efficient in stirring solution than in still solution for GCL2 because the constant of adsorption in stirring solution is much larger than that in still solution. The adsorption of inhibitor GCL2 follows Langmuir＇s adsorption isotherm.

Influence of alkyl group of imidazolinyl-quaternary-ammonium-salt on corrosion inhibition efficiency

The action between imidazolinyl-quaternary-ammonium-salt(IQAS) molecule and Fe atom was studied, and the influence of the alkyl group connected with N atom of imidazoline ring on corrosion inhibition efficiency was explored. Quantum chemical methods, HF/6-31 G and HF/Lan L2 dz, were applied successively to calculate the parameters such as front molecular orbit energy of IQASⅠ-Ⅳ and chemical adsorption for IQASⅠ-Ⅳ and Fe atom. The corrosion inhibition efficiency was measured with the weight loss method of carbon steel samples in acidic solution and oil field sewage. Based on the theoretical analyses and experimental results, it is concluded that N-Fe coordination bond is formed between IQAS molecule and Fe atom, corrosion inhibition efficiency is decreased in the following order(from large to small): IQAS Ⅳ, IQAS Ⅲ, IQAS Ⅱ, IQASⅠ.

Effect of corrosion inhibiting compounds on the corrosion behaviour of pure magnesium and the magnesium alloys EV31A, WE43B and ZE41A

This paper studied corrosion of pure Mg and the Mg alloys EV31A,WE43B,ZE41A,coated with commercial corrosion inhibiting compounds(CICs)(LPS 3,LPS2,AMLGuard,Ardrox 3961)immersed in 3.5 wt%(0.6M)Na Cl solution saturated with Mg(OH)_(2).All four CICs reduced corrosion rates.LPS 3 resulted in zero corrosion rates and 100%inhibition in most cases.LPS 2 and AMLGuard had comparable inhibition efficiencies,whilst Ardrox 3961 had the lowest inhibition efficiency.Reduction in corrosion rates was tentatively attributed to barrier films formed by chemical adsorption for LPS 3 and AMLGuard,and by physical adsorption for LPS2 and Ardrox 3961.

Corrosion inhibition of layered double hydroxides for metal-based systems

Layered double hydroxide(LDH),a kind of 2D layered materials,has been recognized as the promising anticorrosion materials for metal and its alloy.The microstructure,physical/chemical properties,usage in corrosion inhibition and inhibition performance of LDH have been studied separately in open literature.However,there is a lack of a complete review to summarize the status of LDH technology and the potential R&D opportunities in the field of corrosion inhibition.In addition,the challenges for LDH in corrosion inhibition of metal-based system have not been summarized systematically.Herein,we review recent advances in the rational design of LDH for corrosion inhibition of metal-based system(i.e.Mg alloy,Al alloy,steel and concrete)and high-throughput anticorrosion materials development.By evaluating the physical/chemical properties,usage in metal-based system and the corrosion inhibition mechanism of LDH,we highlight several important factors of LDH for anticorrosion performance and common features of LDH in applying different metal alloys.Finally,we provide our perspective and recommendation in this field,including high-throughput techiniques for combinatorial compositional design and rapid synthesis of anticorrosion alloys,with the goal of accelerating the development and application of LDH in corrosion inhibition of metal-based system.

Corrosion Inhibition of Carbon Steel in Hot Hydrochloric Acid Solutions

The dissolution of carbon steel in 5% HCl in the temperature range of 30~90℃ was inhibited by two organic compounds having the general formula: ClR NH2(CH2)n NH2 RCl where R is a benzyl group. The behaviour of these inhibitors in acidic medium were investigated using weight loss method, open circuit potential and linear polarization technique. These inhibitors provided satisfactory corrosion inhibition for carbon steel in hydrochloric acid solutions even at higher temperature and acid concentration (10%). The electrochemical results showed that the polarization resistance (Rp) values increased with increasing inhibitor concentration, also the corrosion current decreased and a higher inhibition efficiency was obtained. The protective properties of these two organic inhibitors were attributed to the chemisorption mechanism

Synergic Mechanism of an Organic Corrosion Inhibitor for Preventing Carbon Steel Corrosion in Chloride Solution

The inhibition effect of dimethylethanolamine（DMEA） and its composite with carboxylic acid was studied with the electrochemical tests. The experimental results indicate that DMEA is not a good inhibitor but the composite of DMEA with caprylic acid exhibits excellent inhibiting efficiency. The synergic mechanism of the organic corrosion inhibitors（OCIs） was studied with quantum chemical calculations. It is found that the DMEA forms a quaternary ammonium salt with the proton in carboxylic acid, and a cyclic complex formed between the salt and Fe may be responsible for the enhancement of inhibiting efficiency. The possible hydrogen bond formed between DMEA and carboxylic acid is not enough for the inhibiting effect. This work is helpful to proposing theoretical interpretation as well as developing a functional organic inhibitor to improve the durability of reinforced concrete contaminated with chloride.

Laccase Immobilized on Mesoporous Silica Materials and Its Corrosion Inhibition Performance in Circulating Cooling Water System

Mesoporous SiO_2 microspheres were synthesized using the sol-gel method and were characterized by TEM, FT-IR and BET techniques. The diameter of the microspheres is about 100—150 nm, and the average mesopore diameter is 2.55 nm, while the specific surface area is 1 088.9 m2/g. Mesoporous SiO_2 microspheres adsorb glutaraldehyde and immobilize laccase by means of the aldehyde group in glutaral which can react with the amidogen of laccase. The immobilization conditions were optimized at a glutaraldehyde concentration of 0.75%, a crosslinking time of 8 h, a laccase concentration of 0.04 L/L and an immobilization time of 10 h. When diesel leakage concentration was 80 mg/L, the highest corrosion inhibition efficiency of immobilized laccase reached 49.23%, which was slightly lower than the corrosion inhibition efficiency of free laccase(59%). The diesel degradation ratio could reach up to 45%. It has been proved that the immobilized laccase could degrade diesel to inhibit corrosion.

L-Proline as a Green Corrosion Inhibitor in Aqueous Solutions for Carbon Steel

The chemical technique was used to investigate the inhibition and adsorption properties of L-proline for steel corrosion(weight loss method).As the concentration of L-proline increased,the inhibition efficiency increased,but decreased as the temperature increased,according to the findings.The inhibitor’s adsorption to the steel surface has been shown to be random,involving both electrostatic and chemisorptions.The Temkin adsorption isotherm governs the adsorption of L-proline to the steel surface.Thermodynamic parameters have been determined in some cases.

Corrosion inhibition of carbon steel in hydrochloric acid by cationic arylthiophenes as new eco-friendly inhibitors: Experimental and quantum chemical study

This study describes the adsorption behavior of three arylthiophene derivatives namely:2-(4-amidino-3-fluorophenyl)-5-[4-methoxy phenyl] thiophene dihydrochloride salt(MA-1217),2-(4-amidinophenyl)-5-[4-chlorophenyll thiophene dihydrochloride salt(MA-1316) and 2-(4-amidino-3-fluorophenyl)-5-[4-ch lorophenyllthiophene dihydrochloride salt(MA-1312) at C-steel in 1.0 mol·L^(-1) HCl interface using experimental and theoretical studies.Electrochemical and mass loss measurements showed that the inhibition efficiency(IE) of the arylthiophene derivatives increases with increasing concentrations and exhibited maximum efficiency 89% at 21×10^(-6) mol·L^(-1)(MA-1217) by mass loss method.The investigated arylthiophene derivatives obey the Langmuir adsorption isotherm.From polarization studies the arylthiophene derivatives act as mixed-type inhibitors.Surface analysis were carried out and discussed.The mode of orientation and adsorption of inhibitor molecules on C-steel surface was studied using molecular dynamics(MD) simulations.Quantum chemical parameters as well as the radial distribution function indices and binding energies confirm the experimental results.

An Electrochemical Study on the Corrosion Inhibition of Stainless Steel by Polyaniline Film

Polyaniline (PANI) film was electrosynthesized on 304 stainless steel by cyclic voltammetry using aqueous oxalic acid as supporting electrolyte. The potential sweep rates were changed to achieve the PANI film with different thickness and structures. Protective properties of the PANI film for corrosion of stainless steel in 3% NaCl aqueous solution were investigated by monitoring potentiodynamic polarization curves and electrochemical impedance spectroscopy (EIS). The results showed that the PANI film which was formed with lower sweep rate led to more positive shift of corrosion potential and greater charge transfer resistance, reflecting higher inhibition for corrosion of the stainless steel.

High-temperature corrosion of phosphate completion fluid and corrosion inhibition method by membrane transformation

By analyzing the corrosion of phosphate completion fluid on the P110 steel at 170 °C, the high-temperature corrosion mechanism of phosphate completion fluid was revealed, and a corrosion inhibition method by membrane transformation was proposed and an efficient membrane-forming agent was selected. Scanning electron microscope (SEM) images, X-ray energy spectrum and X-ray diffraction results were used to characterize the microscopic morphology, elemental composition and phase composition of the precipitation membrane on the surface of the test piece. The effect and mechanism of corrosion inhibition by membrane transformation were clarified. The phosphate completion fluid eroded the test piece by high-temperature water vapor and its hydrolyzed products to form a membrane of iron phosphate corrosion product. By changing the corrosion reaction path, the Zn2+ membrane-forming agent could generate KZnPO4 precipitation membrane with high temperature resistance, uniform thickness and tight crystal packing on the surface of the test piece, which could inhibit the corrosion of the test piece, with efficiency up to 69.63%. The Cu2+ membrane-forming agent electrochemically reacted with Fe to precipitate trace elemental Cu on the surface of the test piece, thus forming a protective membrane, which could inhibit metal corrosion, with efficiency up to 96.64%, but the wear resistance was poor. After combining 0.05% Cu2+ and 0.25% Zn2+, a composite protective membrane of KZnPO4 crystal and elemental Cu was formed on the surface of the test piece. The corrosion inhibition efficiency reached 93.03%, which ensured the high corrosion inhibition efficiency and generated a precipitation membrane resistant to temperature and wear.

Antibacterial and Corrosion Inhibition Properties of SA-ZnO@ODA-GO@PU Super-Hydrophobic Coating in Circulating Cooling Water System

In order to solve the corrosion problem of circulating cooling water system,SA-ZnO@ODA-GO@PU super-hydrophobic coating was synthesized for pipeline protection.After hydrophobic modification,the contact angle(CA)of the coating was above 150°.The antibacterial ability of coating was essential for corrosion protection.SA-ZnO@ODA-GO can seriously damage the cell structure,make the cell content outflow,increase the leakage rate of protein,and make the bacteria unable to reach logarithmic growth phase within 24 h.The corrosion inhibition mechanism analysis of SA-ZnO@ODA-GO@PU coating indicated that the hydrophobic coating as a physical barrier can prevent the water molecules from entering the carbon steel and prevent the surface charge transfer.

CORROSION INHIBITION OF STEARIC ACID LANGMUIR-BLODGETT MONOLAYERS ON IRON

The Langmuir-Blodgett (LB) technique was used for the first time to study inhibition mechanism. Stearic acid Langmuir-Blodgett (SALB) monolayers showed a good inhibition effect on iron corrosion in neutral environment and the inhibition is mainly based on the blocking effect.

Crude Extract of Detergent⁃Like Gleditsia sinensis lam Exhibiting Self⁃Organization for Protection of Mild Steel in Harsh Hydrochloric Acid Solution:How to Seek Crude Natural Plant Extracts as Green Corrosion Inhibitors

This study proposes a thought to employ detergent⁃like renewable low⁃cost crude extract of Gleditsia sinensis lam(GSL)as green corrosion inhibitor for mild steel in HCl solution.Crude Gleditsia sinensis lam extract(GSLE)was gained at mild conditions by simply refluxing in ethanol with a Soxhlet extractor.The target GSLE extract exhibited regular self⁃organization in mixed solvents of organic solvents/H2O such as ethanol/H2 O(v/v,50/50)at room temperature,which was evidenced by different means including scanning electron microscopy,transmission electron microscopy,and dynamic light scattering.The study demonstrates that the yielded assemblies of the crude extract of GSLE displayed chemical adsorption on the studied mild steel sample surfaces.Furthermore,the formed stable crude extract assemblies of GSL presented outstanding anti⁃corrosion capability in 1.0 mol/L HCl aqueous solution based on electrochemical measurements including polarization curves and impedance spectroscopy.It is discovered that the maximal corrosion inhibition efficiency could reach approximate 95%.The molecular modeling was performed to acquire the nature of frontier orbitals of the main representative chemical components of crude GSLE for deep understanding of chemical interactions with iron.The results presented herein would guide us to seek sustainable environmentally friendly low⁃cost detergent⁃like plant crude extracts for corrosion inhibition of various metals in aggressive acid environments.

Corrosion Inhibition Studies of Benzoxazole Derivates for N80 Steel in 1 M HCl Solution: Synthesis, Experimental, and DTF Studies

Three benzoxazole corrosion inhibitors, namely 2-(benzo [d]oxazol-2-yl)phenol (BOP), 6-(benzo [d]oxazol-2-yl)pyridin-2-ol (BOPO), and 2-(quinolin-2-yl) benzo [d]oxazole (QBO), were synthesized. Moreover, their corrosion inhibition performance for N80 steel in 1 M HCl solution at 303 K was measured by the electrochemical measurements and surface analysis studies. The results show that the inhibition efficiency of all corrosion inhibitors increases with the increase of concentration. At the same concentration, the order of inhibition efficiency is BOP < BOPO < QBO. Moreover, the studied inhibitors act as mixed-type inhibitors, and the adsorption of all inhibitors on N80 steel followed the Langmuir adsorption isotherm. Further, we have examined the effect of iodide ions on inhibition efficiency. The results show that BOP and KI are synergistic, BOPO and QBO are competitive adsorptions with KI. The quantum chemical parameters such as highest occupied molecular orbital, lowest unoccupied molecular orbital energy levels, and energy gap were calculated by the density functional theory (DTF). The relations between the inhibition efficiency and some quantum parameters have been discussed. The protective effect of the three inhibitors followed the sequence of BOP < BOPO < QBO. The results obtained from quantum chemicals and electrochemical were in reasonable agreement.

Role of dissolved oxygen reduction in improvement inhibition performance of ascorbic acid during copper corrosion in 0.50 mol/L sulphuric acid

The kinetics of dissolved O_2 reduction and hydrogen evolution reactions on copper surface was studied in naturally aerated and air and O_2-saturated 0.50 mol/L H_2SO_4 solutions using polarization measurements combined with the rotating disc electrode (RDE).The Koutecky-Levich plot indicated that the dissolved O_2 reduction at the copper electrode was an apparent four-electron process.A correlation between the presence of dissolved O_2 and the formation of Cu_2O,confirmed from XRD,was discussed. Ascorbic a...