Engineering Model for Detecting Sensitivity of the Coupling Capacitance Detector

The sensitivity engineering model of the coupling capacitance detector is built to provide the theoretic foundation for designing its circuits and electrodes scientifically. The sensitivity concept model of the capacitance proximity detector is discussed, and the detecting sensitivity of the coupling capacitance detector is analyzed theoretically. Then the sensitivity engineering model, which can reflect the main parameters relationship of the detecting circuit is set up based on the foregoing analyses. It is concluded that: ① the sensitivity is mainly correlative with some parameters including the voltage transmission factor of the demodulator, the oscillating voltage amplitude and the amplitude variation constant of the oscillator; ② the sensitivity is also influenced by the areas of electrodes and the distance between electrodes of the detector.

Energy Recovery Capacitance Coupling Logic and Its Synthesis Methodology

A novel energy recovery logic style ERCCL （energy recovery capacitance coupling logic） , which has good energy performance compared to the conventional CMOS logic and other advanced energy recovery logic, is proposed. ERCCL uses capacitance coupling to perform a logic function, so it can energy-efficiently implement a high fan-in complex logic in a single gate. ERCCL is also a type of threshold logic. The gate count of a system based on ERCCL can be significantly reduced,which,in turn,will decrease the energy loss. A threshold logic synthesis methodology for ERCCL is also presented. MCNC benchmarks are run through the proposed synthesis methodology. The results indicate that about an 80% reduction in gate count can be obtained when compared with the synthesis results of SIS.

Customized modulation on plasma uniformity by non-uniform magnetic field in capacitively coupled plasma

A two-dimensional fluid model based on COMSOL Multiphysics is developed to investigate the modulation of static magnetic field on plasma homogeneity in a capacitively coupled plasma(CCP)chamber. To generate a static magnetic field, direct current is applied to a circular coil located at the top of the chamber. By adjusting the magnetic field's configuration, which is done by altering the coil current and position, both the plasma uniformity and density can be significantly modulated. In the absence of the magnetic field, the plasma density exhibits an inhomogeneous distribution characterized by higher values at the plasma edge and lower values at the center. The introduction of a magnetic field generated by coils results in a significant increase in electron density near the coils. Furthermore, an increase in the sets of coils improves the uniformity of the plasma. By flexibly adjusting the positions of the coils and the applied current,a substantial enhancement in overall uniformity can be achieved. These findings demonstrate the feasibility of using this method for achieving uniform plasma densities in industrial applications.

Abnormal transition of the electron energy distribution with excitation of the second harmonic in low-pressure radio-frequency capacitively coupled plasmas

The self-excited second harmonic in radio-frequency capacitively coupled plasma was significantly enhanced by adjusting the external variable capacitor.At a lower pressure of 3 Pa,the excitation of the second harmonic caused an abnormal transition of the electron energy probability function,resulting in abrupt changes in the electron density and temperature.Such changes in the electron energy probability function as well as the electron density and temperature were not observed at the higher pressure of 16 Pa under similar harmonic changes.The phenomena are related to the influence of the second harmonic on stochastic heating,which is determined by both amplitude and the relative phase of the harmonics.The results suggest that the self-excited high-order harmonics must be considered in practical applications of lowpressure radio-frequency capacitively coupled plasmas.

Plasma density enhancement in radio-frequency hollow electrode discharge

The plasma density enhancement outside hollow electrodes in capacitively coupled radio-frequency(RF) discharges is investigated by a two-dimensional(2D) particle-in-cell/Monte-Carlo collision(PIC/MCC) model. Results show that plasma exists inside the cavity when the sheath inside the hollow electrode hole is fully collapsed, which is an essential condition for the plasma density enhancement outside hollow electrodes. In addition, the existence of the electron density peak at the orifice is generated via the hollow cathode effect(HCE), which plays an important role in the density enhancement. It is also found that the radial width of bulk plasma at the orifice affects the magnitude of the density enhancement, and narrow radial plasma bulk width at the orifice is not beneficial to obtain high-density plasma outside hollow electrodes.Higher electron density at the orifice, combined with larger radial plasma bulk width at the orifice,causes higher electron density outside hollow electrodes. The results also imply that the HCE strength inside the cavity cannot be determined by the magnitude of the electron density outside hollow electrodes.

Effect of a negative DC bias on a capacitively coupled Ar plasma operated at different radiofrequency voltages and gas pressures

The effect of a negative DC bias,|V_(dc)|,on the electrical parameters and discharge mode is investigated experimentally in a radiofrequency(RF)capacitively coupled Ar plasma operated at different RF voltage amplitudes and gas pressures.The electron density is measured using a hairpin probe and the spatio-temporal distribution of the electron-impact excitation rate is determined by phase-resolved optical emission spectroscopy.The electrical parameters are obtained based on the waveforms of the electrode voltage and plasma current measured by a voltage probe and a current probe.It was found that at a low|V_(dc)|,i.e.inα-mode,the electron density and RF current decline with increasing|V_(dc)|;meanwhile,the plasma impedance becomes more capacitive due to a widened sheath.Therefore,RF power deposition is suppressed.When|V_(dc)|exceeds a certain value,the plasma changes toα–γhybrid mode(or the discharge becomes dominated by theγ-mode),manifesting a drastically growing electron density and a moderately increasing RF current.Meanwhile,the plasma impedance becomes more resistive,so RF power deposition is enhanced with|V_(dc)|.We also found that the electrical parameters show similar dependence on|V_(dc)|at different RF voltages,andα–γmode transition occurs at a lower|V_(dc)|at a higher RF voltage.By increasing the pressure,plasma impedance becomes more resistive,so RF power deposition and electron density are enhanced.In particular,theα–γmode transition tends to occur at a lower|V_(dc)|with increase in pressure.

Capacitance extraction method for a gate-induced quantum dot in silicon nanowire metal-oxide-semiconductor field-effect transistors

An improved method of extracting the coupling capacitances of quantum dot structure is reported. This method is based on measuring the charge transfer current in the silicon nanowire metal-oxide-semiconductor field-effect transistor （MOSFET）, in which the channel closing and opening are controlled by applying alternating-current biases with a half period phase shift to the dual lower gates. The capacitances around the dot, including fringing capacitances and barrier capacitances, are obtained by analyzing the relation between the transfer current and the applied voltage. This technique could be used to extract the capacitance parameters not only from the bulk silicon devices, but also from the silicon-on-insulator （SOI） MOSFETs.

Capacitive coupling induced Kondo–Fano interference in side-coupled double quantum dots

We report capacitive coupling induced Kondo–Fano(K–F) interference in a double quantum dot(DQD) by systematically investigating its low-temperature properties on the basis of hierarchical equations of motion evaluations. We show that the interdot capacitive coupling U12 splits the singly-occupied(S-O) state in quantum dot 1(QD1) into three quasi-particle substates: the unshifted S-O0 substate, and elevated S-O1 and S-O2. As U12 increases, S-O2 and S-O1 successively cross through the Kondo resonance state at the Fermi level(ω = 0), resulting in the so-called Kondo-I(KI), K–F, and Kondo-II(KII) regimes. While both the KI and KII regimes have the conventional Kondo resonance properties, remarkable Kondo–Fano interference features are shown in the K–F regime. In the view of scattering, we propose that the phase shift η(ω)is suitable for analysis of the Kondo–Fano interference. We present a general approach for calculating η(ω) and applying it to the DQD in the K–F regime where the two maxima of η(ω = 0) characterize the interferences between the Kondo resonance state and S-O2 and S-O1 substates, respectively.

A New Configuration for Planar Magnetic Elements to Reduce Capacitive Couplings

This paper presents an analysis of planar magnetic element configurations in order to reduce capacitive couplings between the windings. The capacitive couplings between layers of planar magnetic elements introduce a stray capacitor which can conduct high frequency currents when high dv/dt voltage is applied. High frequency current may cause electromagnetic interference （EMI） and harmonic problems. The investigation and simulation results, both 2D and 3D Finite Element （FE） show the effect of shifting the planar layers in reduction of the capacitive couplings. The simulation results are compared with test results to validate the proposition.

Effect of parallel resonance on the electron energy distribution function in a 60 MHz capacitively coupled plasma

In general,as the radio frequency(RF)power increases in a capacitively coupled plasma(CCP),the power transfer efficiency decreases because the resistance of the CCP decreases.In this work,a parallel resonance circuit is applied to improve the power transfer efficiency at high RF power,and the effect of the parallel resonance on the electron energy distribution function(EEDF)is investigated in a 60 MHz CCP.The CCP consists of a power feed line,the electrodes,and plasma.The reactance of the CCP is positive at 60 MHz and acts like an inductive load.A vacuum variable capacitor(VVC)is connected in parallel with the inductive load,and then the parallel resonance between the VVC and the inductive load can be achieved.As the capacitance of the VVC approaches the parallel resonance condition,the equivalent resistance of the parallel circuit is considerably larger than that without the VVC,and the current flowing through the matching network is greatly reduced.Therefore,the power transfer efficiency of the discharge is improved from 76%,70%,and 68%to 81%,77%,and 76%at RF powers of 100 W,150 W,and 200 W,respectively.At parallel resonance conditions,the electron heating in bulk plasma is enhanced,which cannot be achieved without the VVC even at the higher RF powers.This enhancement of electron heating results in the evolution of the shape of the EEDF from a biMaxwellian distribution to a distribution with the smaller temperature difference between high-energy electrons and low-energy electrons.Due to the parallel resonance effect,the electron density increases by approximately 4%,18%,and 21%at RF powers of 100 W,150 W,and 200 W,respectively.

Global simulation of plasma series resonance effect in radio frequency capacitively coupled Ar/O_(2) plasma

Radio frequency capacitively coupled plasmas(RF CCPs)play a pivotal role in various applications in etching and deposition processes on a microscopic scale in semiconductor manufacturing.In the discharge process,the plasma series resonance(PSR)effect is easily observed in electrically asymmetric and geometrically asymmetric discharges,which could largely influence the power absorption,ionization rate,etc.In this work,the PSR effect arising from geometrically and electrically asymmetric discharge in argon-oxygen mixture gas is mainly investigated by using a plasma equivalent circuit model coupled with a global model.At relatively low pressures,as Ar content(α)increases,the inductance of the bulk is weakened,which leads to a more obvious PSR phenomenon and a higher resonance frequency(ω_(psr)).When the Ar content is fixed,varying the pressure and gap distance could also have different effects on the PSR effect.With the increase of the pressure,the PSR frequency shifts towards the higher order,but in the case of much higher pressure,the PSR oscillation would be strongly damped by frequent electron-neutral collisions.With the increase of the gap distance,the PSR frequency becomes lower.In addition,electrically asymmetric waveforms applied to a geometrically asymmetric chamber may weaken or enhance the asymmetry of the discharge and regulate the PSR effect.In this work,the Ar/O_(2) electronegative mixture gas is introduced in a capacitive discharge to study the PSR effect under geometric asymmetry effect and electrical asymmetry effect,which can provide necessary guidance in laboratory research and current applications.

Enhancing surface adhesion of polytetrafluoroethylene induced by two-step in-situ treatment with radiofrequency capacitively coupled Ar/Ar+CH_(4)+NH_(3) plasma

Although some progress in plasma modification of the polytetrafluoroethylene(PTFE) surface has been made recently,its adhesion strength still needs to be further improved.In this work,the surface of a PTFE sample was treated with a two-step in-situ method.Firstly,the PTFE surface was treated with capacitively coupled Ar plasma to improve its mechanical interlocking performance;then,Ar+NH_(3)+CH_(4) plasma was used to deposit an a-CNx:H cross-linking layer on the PTFE surface to improve the molecular bonding ability.After treatment,a high specific surface area of 2.20 and a low F/C ratio of 0.32 were achieved on the PTFE surface.Its surface free energy was increased significantly and its maximum adhesion strength reached77.1 N·10 mm^(-1),which is 56% higher than that of the single-step Ar plasma-treated sample and32% higher than that of the single-step Ar+CH_(4)+NH_(3) plasma-treated sample.

Shielding Effectiveness of Rural Concealed Communication Cable of Asymmetric/Symmetric Slots with Different Shapes

With the rural concealed communication cable as the study object, the shielding effectiveness of different slot shapes was analyzed by using LBEM （linear boundary element method）. The engineering example results showed that for twocore shielded cable, the coupling capacitance of trapezoid slots （asymmetric and symmetric） changed the most, followed by rectangular slots （asymmetric and symmetric）, and the changes of wedge slots were the smallest, but the change tenden- cies were consistent. In addition, with the increase of slot width of different slots, the coupling capacitance of tow-cored shielded cable showed small change.

Crosstalk Estimation and Optimization in Deep Sub-Micron VLSI

RLC model is used to estimate the coupling noise between interconnect wires and make some analysis through the simulation result. Based on the analysis conclusion,some algorithms are developed to adjust the rou ting result with crosstalk constraint.

Frequency Matching Effects on Characteristics of Bulk Plasmas and Sheaths for Dual-Frequency Capacitively Coupled Argon Discharges: One-Dimensional Fluid Simulation

A one-dimensional fluid model is proposed to simulate the dual-frequency capacitively coupled plasma for Ar discharges. The influences of the low frequency on the plasma density, electron temperature, sheath voltage drop, and ion energy distribution at the powered electrode are investigated. The decoupling effect of the two radio-frequency sources on the plasma parameters, especially in the sheath region, is discussed in detail.

Characteristics of dual-frequency capacitively coupled SF_6/O_2 plasma and plasma texturing of multi-crystalline silicon

Due to it being environmentally friendly, much attention has been paid to the dry plasma texturing technique serving as an alternative candidate for multicrystalline silicon （mc-Si） surface texturing. In this paper, capacitively coupled plasma （CCP） driven by a dual frequency （DF） of 40.68 MHz and 13.56 MHz is first used for plasma texturing of mc-Si with SF6/O2 gas mixture. Using a hairpin resonant probe and optical emission techniques, DF-CCP characteristics and their influence on mc-silicon surface plasma texturing are investigated at different flow rate ratios, pressures, and radio-frequency （RF） input powers. Experimental results show that suitable plasma texturing of mc-silicon occurs only in a narrow range of plasma parameters, where electron density ne must be larger than 6.3 x 109 cm-3 and the spectral intensity ratio of the F atom to that of the O atom （[F]/[O]） in the plasma must be between 0.8 and 0.3. Out of this range, no cone-like structure is formed on the mc-silicon surface. In our experiments, the lowest reflectance of about 7.3% for mc-silicon surface texturing is obtained at an [F]/[O] of 0.5 and ne of 6.9 × 109 cm-3.

Plasma Uniformity in a Dual Frequency Capacitively Coupled Plasma Reactor Measured by Optical Emission Spectroscopy

Local measurement of plasma radial uniformity was performed in a dual frequency capacitively coupled argon plasma （DF-CCP） reactor using an optical probe. The optical probe collects the light emission from a small separate volume in plasma, thus enabling to diagnose the plasma uniformity for different experimental parameters. Both the gas pressure and the low- frequency （LF） power have apparent effects on the radial uniformity of argon plasma. With the increase in either pressure or LF power, the emission profiles changed from a bell-shaped to a double-peak distribution. The influence of a fused-silica ring around the electrodes on the plasma uniformity was also studied using the optical probe. Possible reasons that result in nonuniform plasmas in our experiments are discussed.

A One-Dimensional Hybrid Simulation of DC/RF Combined Driven Capacitive Plasma

We developed a one-dimensional hybrid model to simulate the DC/RF combined driven capacitively coupled plasma for argon discharges. The numerical results are used to analyze the influence of the DC source on the plasma density distribution, ion energy distributions （IEDs） and ion angle distributions （IADs） on both the RF and DC electrodes. The increase in DC voltage drives more high-energy ions to the electrode applied to the DC source, which makes the IEDs at the DC electrode shift towards higher energy, and the peaks in the IADs shift towards small angle regions. At the same time, it also decreases the ion energy at the RF electrode and enlarges the incident angles of the ions, which strike the RF electrode.

Surface modification of silicone rubber by CF4 radio frequency capacitively coupled plasma for improvement of flashover

The flashover performance of insulating materials plays an important role in the development of high-voltage insulation systems.In this paper,silicone rubber(SIR)is modified by CF4 radio frequency capacitively coupled plasma(CCP)for the improvement of surface insulation performance.The discharge mode and active particles of CCP are diagnosed by the digital single-lens reflex and the spectrometer.Scanning electron microscopy and x-ray photoelectron spectroscopy are used for the surface physicochemical properties of samples,while the surface charge dissipation,charge accumulation measurement,and flashover test are applied for the surface electrical characteristics.Experimental results show that the fluorocarbon groups can be grafted and the surface roughness increases after plasma treatment.Besides,the surface charge dissipation is decelerated and the positive charge accumulation is inhibited obviously for the treated samples.Furthermore,the surface flashover voltage can be increased by 26.67%after 10 min of treatment.It is considered that strong electron affinity of C–F and increased surface roughness can contribute to deepening surface traps,which not only inhibits the development of secondary electron emission avalanche but also alleviates the surface charge accumulation and finally improves the surface flashover voltage of SIR.

Signal Acquisition and Processing Method for Capacitive Electromagnetic Flowmeter

A kind of signal acquisition circuit and the related signal processing method of the capacitanceelectromagnetic flowmeter (EMF) were introduced. The circuit can eliminate the influence of distributed capacitanceon the input impedance of the operational amplifier, and greatly improve the input impedance of the detection circuitto overcome the disadvantage of high signal source impedance. The rotating capacitor filter is a signal processingmethod based on the phase-sensitive detection technology. It can extract the weak signal from the strong and widebandbackground noise, so it is very suitable for the processing of capacitive electromagnetic flow signals. Throughthe comparison of the signal amplitude obtained at different flow rates and the comparison of signal spectrumcomponents before and after the filter, the effectiveness of the bootstrap signal acquisition circuit and rotatingcapacitor filtering method is verified.