Mechanism of high Li-ion conductivity in poly(vinylene carbonate)-poly(ethylene oxide)cross-linked network based electrolyte revealed by solid-state NMR

Solid polymer electrolytes(SPEs)have become increasingly important in advanced lithium-ion batteries(LIBs)due to their improved safety and mechanical properties compared to organic liquid electrolytes.Cross-linked polymers have the potential to further improve the mechanical property without trading off Li-ion conductivity.In this study,focusing on a recently developed cross-linked SPE,i.e.,the one based on poly(vinylene carbonate)-poly(ethylene oxide)cross-linked network(PVCN),we used solid-state nuclear magnetic resonance(NMR)techniques to investigate the fundamental interaction between the chain segments and Li ions,as well as the lithium-ion motion.By utilizing homonuclear/heteronuclear correlation,CP(cross-polarization)kinetics,and spin-lattice relaxation experiments,etc.,we revealed the structural characteristics and their relations to lithium-ion mobilities.It is found that the network formation prevents poly(ethylene oxide)chains from crystallization,which could create sufficient space for segmental tumbling and Li-ion co nductio n.As such,the mechanical property is greatly improved with even higher Li-ion mobilities compared to the poly(vinylene carbonate)or poly(ethylene oxide)based SPE analogues.

Residual alkali-evoked cross-linked polymer layer for anti-air-sensitivity LiNi_(0.89)Co_(0.06)Mn_(0.05)O_(2)cathode

High-energy density lithium-ion batteries(LIBs)with layered high-nickel oxide cathodes(LiNi_(x)Co_(y)Mn_(1-x-y)O_(2),x≥0.8)show great promise in consumer electronics and vehicular applications.However,LiNi_(x)Co_(y)Mn_(1-x-y)O_(2)faces challenges related to capacity decay caused by residual alkalis owing to high sensitivity to air.To address this issue,we propose a hazardous substances upcycling method that fundamentally mitigates alkali content and concurrently induces the emergence of an anti-air-sensitive layer on the cathode surface.Through the neutralization of polyacrylic acid(PAA)with residual alkalis and then coupling it with 3-aminopropyl triethoxysilane(KH550),a stable and ion-conductive cross-linked polymer layer is in situ integrated into the LiNi_(0.89)Co_(0.06)Mn_(0.05)O_(2)(NCM)cathode.Our characterization and measurements demonstrate its effectiveness.The NCM material exhibits impressive cycling performance,retaining 88.4%of its capacity after 200 cycles at 5 C and achieving an extraordinary specific capacity of 170.0 mA h g^(-1) at 10 C.Importantly,this layer on the NCM efficiently suppresses unfavorable phase transitions,severe electrolyte degradation,and CO_(2)gas evolution,while maintaining commendable resistance to air exposure.This surface modification strategy shows widespread potential for creating air-stable LiNi_(x)Co_(y)Mn_(1-x-y)O_(2)cathodes,thereby advancing high-performance LIBs.

Tuning the cross-linked structure of basic poly(ionic liquid)to develop an efficient catalyst for the conversion of vinyl carbonate to dimethyl carbonate

Dimethyl carbonate(DMC)is a crucial chemical raw material widely used in organic synthesis,lithiumion battery electrolytes,and various other fields.The current primary industrial process employs a conventional sodium methoxide basic catalyst to produce DMC through the transesterification reaction between vinyl carbonate and methanol.However,the utilization of this catalyst presents several challenges during the process,including equipment corrosion,the generation of solid waste,susceptibility to deactivation,and complexities in separation and recovery.To address these limitations,a series of alkaline poly(ionic liquid)s,i.e.[DVBPIL][PHO],[DVCPIL][PHO],and[TBVPIL][PHO],with different crosslinking degrees and structures,were synthesized through the construction of cross-linked polymeric monomers and functionalization.These poly(ionic liquid)s exhibit cross-linked structures and controllable cationic and anionic characteristics.Research was conducted to investigate the effect of the cross-linking degree and structure on the catalytic performance of transesterification in synthesizing DMC.It was discovered that the appropriate cross-linking degree and structure of the[DVCPIL][PHO]catalyst resulted in a DMC yield of up to 80.6%.Furthermore,this catalyst material exhibited good stability,maintaining its catalytic activity after repeated use five times without significant changes.The results of this study demonstrate the potential for using alkaline poly(ionic liquid)s as a highly efficient and sustainable alternative to traditional catalysts for the transesterification synthesis of DMC.

The Role of Certificates and Labels for Cocoa in the Face of Climate Change: A Scientific Review

Climate change threatens cocoa quality, raising concerns regarding sustainable premium cocoa production. Evaluating the effectiveness of certification standards is imperative to address this concern effectively. A multi-stage method was employed for a systematic review of 39 peer-reviewed articles to highlight the impacts of climate change on the biophysical environment of cocoa and its implications for adapting Geographical Indications (GIs). Additionally, a comprehensive review was conducted on climate-relevant standards of certificates in Ecuador, Indonesia, and Ghana. The findings of this study provide practical insights into possible difficulties that cocoa-producing countries may encounter in maintaining the distinctive flavours and quality trademarks of cocoa in the face of changing climate. Moreover, the findings emphasize the need for producer countries to prioritize viable adaptation and product differentiation strategies that meet sustainable marketing standards to protect GIs or place-based intellectual property. Furthermore, the findings indicate certificates require effective multi-level climate change management and environmental-social-governance principles that promote scientifically proven mitigation strategies, such as increasing soil organic carbon, zero deforestation, and reducing emissions while striving to leverage local adaptation policies to reduce location-specific vulnerability. Finally, certificates can accelerate the expansion, intensification, and redistribution of sustainable production for gains that outweigh the inconveniences caused by climate change.

In situ formed cross-linked polymer networks as dual-functional layers for high-stable lithium metal batteries

Lithium-metal anodes(LMAs)have been recognized as the ultimate anodes for next-generation batteries with high energy density,but stringent assembly-environment conditions derived from the poor moisture stability dramatically hinder the transformation of LMAs from laboratory to industry.Herein,an in situ formed cross-linked polymer layer on LMAs is designed and constructed by a facile thiol-acrylate click chemistry reaction between poly(ethylene glycol)diacrylate(PEGDA)and the crosslinker containing multi thiol groups under UV irradiation.Owing to the hydrophobic nature of the layer,the treated LMAs demonstrate remarkable humid stability for more than 3 h in ambient air(70%relative humidity).The coating humid-resistant protective layer also possesses a dual-functional characterization as solid polymer electrolytes by introducing lithium bis(trifluoromethanesulfonyl)imide in the system in advance.The intimate contact between the polymer layer and LMAs reduces interfacial resistance in the assembled Li/LiFePO_(4)or Li/LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2)full cell effectively,and endows the cell with an outstanding cycle performance.

Cross-linked polyelectrolyte reinforced SnO_(2)electron transport layer for robust flexible perovskite solar cells

SnO_(2)electron transport layer(ETL)is a vital component in perovskite solar cells(PSCs),due to its excellent photoelectric properties and facile fabrication process.In this study,we synthesized a water-soluble and adhesive polyelectrolyte with ethanolamine(EA)and poly-acrylic acid(PAA).The linear PAA was crosslinked by EA,forming a 3D network that stabilized the SnO_(2)nanoparticle dispersion.An organic–inorganic hybrid ETL is developed by introducing the cross-linked PAA-EA into SnO_(2)ETL,which prevents nano particle agglomeration and facilitates uniform SnO_(2)film formation with fewer defects.Additionally,the PAA-EA-modified SnO_(2)facilitated a uniform and compact perovskite film,enhancing the interface contact and carrier transport.Consequently,the PAA-EA-modified PSCs exhibited excellent PCE of 24.34%and 22.88%with high reproducibility for areas of 0.045 and 1.00 cm~2,respectively.Notably,owing to structure reinforce effect of PAA-EA in SnO_(2)ETL,flexible device demonstrated an impressive PCE of 23.34%while maintaining 90.1%of the initial PCE after 10,000 bending cycles with a bending radius of 5 mm.This successful approach of polyelectrolyte reinforced hybrid organic–inorganic ETL displays great potential for flexible,large-area PSCs application.

A UV cross-linked gel polymer electrolyte enabling high-rate and high voltage window for quasi-solid-state supercapacitors

Serving as a promising alternative to liquid electrolyte in the application of portable and wearable devices,gel polymer electrolytes(GPEs)are expected to obtain more preferable properties rather than just be satisfied with the merits of high safety and deformability.Here,an easy-operated method is employed to fabricate cross-linked composite polymer membranes used for GPEs assisted by UV irradiation,in which N-doped carbon quantum dots(N-CQDs)and TiO2are introduced as photocatalysts and additives to improve the performances of GPEs.Specifically,N-CQDs participate as a cross-linker to construct the inner porous structure,and TiO2nanoparticles serve as a stabilizer to improve the electrochemical stability of GPEs under high voltage(3.5 V).The excellent thermal and mechanical stability of the membrane fabricated in this work guarantee the safety of the supercapacitors(SCs).This GPE based SC not only exhibits prominent rate performance(105%capacitance retention at the current density of 40A g^(-1))and cyclic stability(85%at 1 A g^(-1)under 3.5 V after 20,000 cycles),but also displays remarkable energy density(42.88 Wh kg^(-1))with high power density(19.3 k W kg^(-1)).Moreover,the superior rate and cycling performances of the as-prepared GPE based flexible SCs under flat and bending state confirm the feasibility of its application in flexible energy storage devices.

A Self-Healing and Nonflammable Cross-Linked Network Polymer Electrolyte with the Combination of Hydrogen Bonds and Dynamic Disulfide Bonds for Lithium Metal Batteries

The self-healing solid polymer electrolytes(SHSPEs)can spontaneously eliminate mechanical damages or micro-cracks generated during the assembly or operation of lithium-ion batteries(LIBs),significantly improving cycling performance and extending service life of LIBs.Here,we report a novel cross-linked network SHSPE(PDDP)containing hydrogen bonds and dynamic disulfide bonds with excellent self-healing properties and nonflammability.The combination of hydrogen bonding between urea groups and the metathesis reaction of dynamic disulfide bonds endows PDDP with rapid self-healing capacity at 28°C without external stimulation.Furthermore,the addition of 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide(EMIMTFSI)improves the ionic conductivity(1.13×10^(−4)S cm^(−1)at 28°C)and non-flammability of PDDP.The assembled Li/PDDP/LiFePO_(4)cell exhibits excellent cycling performance with a discharge capacity of 137 mA h g^(−1)after 300 cycles at 0.2 C.More importantly,the self-healed PDDP can recover almost the same ionic conductivity and cycling performance as the original PDDP.

Certrust:An SDN-Based Framework for the Trust of Certificates against Crossfire Attacks in IoT Scenarios

The low-intensity attack flows used by Crossfire attacks are hard to distinguish from legitimate flows.Traditional methods to identify the malicious flows in Crossfire attacks are rerouting,which is based on statistics.In these existing mechanisms,the identification of malicious flows depends on the IP address.However,the IP address is easy to be changed by attacks.Comparedwith the IP address,the certificate ismore challenging to be tampered with or forged.Moreover,the traffic trend in the network is towards encryption.The certificates are popularly utilized by IoT devices for authentication in encryption protocols.DTLShps proposed a new way to verify certificates for resource-constrained IoT devices by using the SDN controller.Based on DTLShps,the SDN controller can collect statistics on certificates.In this paper,we proposeCertrust,a framework based on the trust of certificates,tomitigate the Crossfire attack by using SDN for IoT.Our goal is threefold.First,the trust model is built based on the Bayesian trust system with the statistics on the participation of certificates in each Crossfire attack.Moreover,the forgetting curve is utilized instead of the traditional decay method in the Bayesian trust system for achieving a moderate decay rate.Second,for detecting the Crossfire attack accurately,a method based on graph connectivity is proposed.Third,several trust-based routing principles are proposed tomitigate the Crossfire attack.These principles can also encourage users to use certificates in communication.The performance evaluation shows that Certrust is more effective in mitigating the Crossfire attack than the traditional rerouting schemes.Moreover,our trust model has a more appropriate decay rate than the traditional methods.

Self-Cross-Linked Tannin-Aminated Tannin Surface Coatings for Particleboard

Aminated tannins were prepared by reacting mimosa condensed tannin extract with ammonia yielding the substitution of many,if not all of the tannin hydroxyl groups with–NH_(2)groups.A tannin-aminated tannin(ATT)particleboard coating was then prepared by reacting raw tannin extract with aminated tannin extract and thus cross-linking the two by substituting tannin’s hydroxyl groups with the–NH_(2)groups on the aminated tannin to form–NH-bridges between the two.The resulting particleboard coating gave encouraging results when pressed at 180℃for 3 min.Conversely,the system in which tannin was reacted/cross-liked with urea(ATU)by a similar amination reaction did not perform as well as the ATT system,and this even when a higher curing temperature and longer hot press time were used.In particular its water repellence was worse probably due to the presence of urea and such a system with lower reactivity.Nonetheless,substituting the tannin–OHs with the urea–NH_(2)groups appeared to also take place.ATT gave better results than ATU as regards water repellence and mechanical resistance as shown by the cross cut test.The ATT system was shown to be between 95%and 98%biosourced.The difference appeared to be due,by TMA analysis,to the much faster formation of the ATT hardened network leading to a better cross-linked polymer coating.The chemical species formed for both the ATT and ATU system were studied by MALDI ToF and CP MAS^(13)C NMR.

Does Green Food Certification promote agri-food export quality?Evidence from China

The construction of a food certification system plays a vital role in upgrading export quality, which previous studies have largely overlooked. We match China's industry-level data of Green Food Certification with its HS6-digit export data of agri-food products to quantify the impact of Green Food Certification on export quality. We identify the significant and positive effect of Green Food Certification on export quality. The 2SLS estimation based on instrumental variables and a range of robustness checks confirm the validity and robustness of the benchmark conclusions. Further analysis discloses that Green Food Certification improves export quality by raising agricultural production efficiency and brand premiums. Heterogeneity analysis shows that the effect of Green Food Certification varies across regions, notably improving the quality of agri-food products exported to developed regions and regions with high levels of import supervision. Furthermore, among various product types, Green Food Certification significantly improves the export quality of primary products and products vulnerable to non-tariff measures. The above findings could guide the future development of agri-food quality certification systems, potentially leading to a transformation and promotion of the agri-food trade.

Early changes in corneal densitometry after FS-LASIK combined with accelerated corneal cross-linking for correction of high myopia

AIM:To observe the effects of femtosecond laserassisted excimer laser in situ keratomileusis combined with accelerated corneal cross-linking(FS-LASIK Xtra)on corneal densitometry after correcting for high myopia.METHODS:In this prospectively study,130 patients underwent FS-LASIK or FS-LASIK Xtra for high myopia.Their right eyes were selected for inclusion in the study,of which 65 cases of 65 eyes in the FS-LASIK group,65 patients with 65 eyes in the FS-LASIK Xtra group.Patients were evaluated for corneal densitometry at 1,3,and 6mo postoperatively using Pentacam Scheimpflug imaging.RESULTS:Preoperative differences in corneal densitometry between the FS-LASIK and FS-LASIK Xtra groups in different ranges were not statistically significant(P>0.05).Layer-by-layer analysis revealed statistically significant differences in the anterior(120μm),central,and total layer corneal densitometry between the FS-LASIK and FS-LASIK Xtra groups at 1 and 3mo postoperatively(all P<0.05),the FS-LASIK Xtra group is higher than that of the FS-LASIK group.Analysis of different diameter ranges showed statistically significant differences between the FS-LASIK group and the FS-LASIK Xtra group at 1mo postoperatively in the ranges of 0–2,2–6,and 6–10 mm(both P<0.05);At 3mo postoperatively,the FS-LASIK Xtra group is higher than that of the FS-LASIK group in the ranges of 0–2 and 2–6 mm(P<0.05).At 6mo postoperatively,there were no statistically significant differences in corneal densitometry between the FS-LASIK group and the FS-LASIK Xtra group in different diameter ranges(all P>0.05).CONCLUSION:There is an increase in internal corneal densitometry during the early postoperative period after FS-LASIK Xtra for correction of high myopia.However,the densitometry values decreased to the level of conventional FS-LASIK at 6mo after surgery,with the most significant changes observed in the superficial central zone.

Construction and Reflection of Software Engineering Major Based on Accreditation Board for Engineering and Technology (ABET) Certification

With the rapid development of information technology,the demand for talents in the field of software engineering is growing.In order to cultivate high-quality software engineering talents who meet the market demand,universities have continuously carried out the construction of software engineering majors.Accreditation Board for Engineering and Technology(ABET)certification,as an internationally recognized higher education quality assurance system,provides important reference and guidance for the construction of software engineering majors.Guided by student learning outcomes and core competencies,combined with the characteristics of software engineering talent cultivation,the innovation of talent cultivation mode takes industry-education integration and school-enterprise cooperation as the main development paths and explores comprehensive reform of the major in terms of professional positioning and goals,curriculum system,teaching conditions,and teachers.This comprehensive reform model has effectively promoted the development of major construction and improved the quality of talent cultivation.

Discussion on the Integration of“Post,Course,Competition,Certificate”:Taking the Internet of Things Application Technology Courses in Higher Vocational Colleges as an Example

This article explores the development of the Internet of Things(IoT)application technology course in higher vocational colleges under the background of“post,course,competition,certificate.”It first emphasizes the importance of IoT talent training and course construction in higher vocational colleges and deeply analyzes the core concept of“post,course,competition,certificate”integration.In view of the problems faced in the course construction of IoT application technology in higher vocational colleges and the practical experience of Tianjin Vocational College of Mechanics and Electricity,the implementation strategy of the course construction of IoT application technology in higher vocational colleges is elaborated in detail based on the integrated concept of“post,course,competition,certificate.”

The Model of“Post,Course,Competition,Certificate”Integrated Education for Electronic Information Engineering Technology Major in Higher Vocational Colleges

The core education function of higher vocational colleges is to train technical talents with high quality,so as to meet the needs of talents in the development stage of our society.Under the guidance of talent training,higher vocational colleges need to pay attention to establishing an all-round and three-dimensional education model,and promote innovation of higher vocational education on the basis of this.It is also a way to promote the innovation of higher vocational education to vigorously promote the construction of“post,course,competition,certificate”mode in the construction of education mode.Through the construction of“post,course,competition,certificate”mode,the education mode of higher vocational colleges is gradually improved,so as to strengthen the effectiveness of talent training in higher vocational colleges.Therefore,in this paper,the author puts forward some suggestions to promote the construction of the integrated education mode of the electronic information engineering technology major in higher vocational colleges,so as to help improve the talent training level of higher vocational colleges.

Suggestions for the "Integration in Multiple Certificates" Curriculum System Construction

Business English professional "Integration in Multiple Certificates" refers to these two kinds of certificates——a diploma and vocational certificates. Business English curriculum design unified vocational qualification certificate with professional training objectives. Basis on the meeting of requirements of certificates for graduation, making professional training contents, curriculum,teaching methods together with vocational training and the requirements of professional qualification certificates.

Study on the Soy Protein-Based Adhesive Cross-Linked by Glyoxal

Based on the ESI-MS and ^(13)C-NMR analysis of the forms of glyoxal in acidic and alkaline solutions,the soy-based adhesive cross-linked by glyoxal was prepared in this work.The results showed that glyoxal existed in water in different forms at different pH levels.Under alkaline conditions,glyoxal transformed to glycolate through the intramolecular disproportionation reaction.Under acidic conditions,although some of glyoxal transformed to glycolate as what happened under alkaline conditions,most of glyoxal molecules existed in the form of fiveor six-membered cyclic ether structure.No ethylene tetraol or free aldehyde group was actually detected under these conditions.Although glyoxal reacted with soy protein under both acidic and alkaline conditions,alkaline conditions were more favorable for the improvement of mechanical performance and water resistance of soybased adhesives than acid conditions.

Applications of Crown Ether Cross-Linked Chitosan for the Analysis of Lead and Cadmium in Environmental Water Samples

A new type of crown ether cross-linked chitosan was synthesized by the reaction of chitosan with 4,4′-dibromodibenzo-18-crown-6 (Br-DBC). Its token structure was analyzed with FT-IR and NMR and the adsorption behaviors for lead and cadmium in environmental water samples by FAAS were studied. In addition the best analysis conditions were discussed and the adsorption mechanism was explained. As the enrichment factor is above 100, both recoveries are 94%–106%, the detection limits of lead and cadmium are 0.5μg·L?1 and 0.04 μg·L?1 and the relatively standard deviations of lead and cadmium are 3.1% and 2.8% respectively, this new method was successfully applied to the determination of environmental water samples. This method is fast and simple and it greatly enhances the determination ability of FAAS for lead and cadmium.

Adsorptive Removal of Copper Ions from Aqueous Solution Using Cross-linked Magnetic Chitosan Beads

The performance of cross-linked magnetic chitosan, coated with magnetic fluids and cross-linked with ePichlorohydrin, was investigated for the adsorption of Copper （Ⅱ） from aqueous solutions. Infrared spectra of chitosan before and after modification showed that the coating and cross-linking are effective. Experiments were performed at different pH of solution and contact time, and appropriate conditions for the adsorption of Cu（Ⅱ） were determined. Experimental equilibrium data were correlated with Langmuir and Freundlich isotherms for determination of the adsorption potential. The results showed that the Langmuir isotherm was better compared with the Freundlich isotherm, and the uptake of Cu（Ⅱ） was 78.13 mg·g^- 1. The kinetics of adsorption corresponded with the first-order Langergren rate equation, and Langergren rate constants were determined.

Simultaneously enhanced moisture tolerance and defect passivation of perovskite solar cells with cross-linked grain encapsulation

The grain surfaces(film surface and grain boundary)of polycrystalline perovskite films are vulnerable sites in solar cells since they pose a high defect density and initiate the degradation of perovskite absorber.Achieving simultaneously defect passivation and grain protection from moisture is crucial for the viability of perovskite solar cells.Here,an in situ cross-linked grain encapsulation(CLGE)strategy that improves both device stability and defect passivation is reported.Cross-linkable semiconducting small molecules are mixed into the antisolvent to uniformly form a compact and conducting cross-linked layer over the grain surfaces.This cross-linked coating layer not only passivates trap states and facilitates hole extraction,but also enhances the device stability by preventing moisture diffusion.Using the CLGE strategy,a high power conversion efficiency(PCE)of 22.7%is obtained in 1.55-eV bandgap planar perovskite solar cells.The unencapsulated devices with CLGE exhibit significantly enhanced device stability again moisture and maintain>90%of their initial PCE after shelf storage under ambient condition for over10,000 h.