Cu-Fe composite oxides were prepared by co-precipitation method and tested for higher alcohol synthesis from syngas. The selectivity to C2＋OH and C6＋OH in alcohol distribution was very high while the methane product...Cu-Fe composite oxides were prepared by co-precipitation method and tested for higher alcohol synthesis from syngas. The selectivity to C2＋OH and C6＋OH in alcohol distribution was very high while the methane product fraction in hydrocarbon distribution was rather low, demonstrating a promising potential in higher alcohols synthesis from syngas. The distribution of alcohols and hydrocarbons approximately obeyed Anderson-Schulz-Flory distribution with similar chain growth probability, indicating alcohols and hydrocarbons derived from the same intermediates. The effects of Cu/Fe molar ratio, reaction temperature and gas hourly space velocity （GHSV） on catalytic performance were studied in detail. The sample with a Cu/Fe molar ratio of 10/1 exhibited the best catalytic performance. Higher reaction temperature accelerated water-gas-shift reaction and led to lower total alcohols selectivity. GHSV showed great effect on catalytic performance and higher GHSV increased the total alcohol selectivity, indicating there existed visible dehydration reaction of alcohol into hydrocarbon.展开更多
A novel‐structured Mo‐Cu‐Fe‐O composite was successfully prepared by co‐precipitation and impregnation method.The properties of the as‐prepared samples were determined using X‐ray diffraction,temperature‐progr...A novel‐structured Mo‐Cu‐Fe‐O composite was successfully prepared by co‐precipitation and impregnation method.The properties of the as‐prepared samples were determined using X‐ray diffraction,temperature‐programmed reduction by H2,cyclic voltammetry,and temperature‐programmed desorption by O2.The results showed that Mo6+diffused into the Cu‐Fe‐O crystal lattice and then formed a new crystalline phase of CuMoO4.The Mo‐Cu‐Fe‐O catalyst had redox properties,and its surface contained active sites for oxygen adsorption.In addition,the catalytic activity of the Mo‐Cu‐Fe‐O composite was evaluated by the degradation of Cationic Red GTL,Crystal Violet,and Acid Red in catalytic wet air oxidation(CWAO)at ambient temperature and pressure.The Mo‐Cu‐Fe‐O catalyst showed excellent activity at basic conditions for the degradation of Cationic Red GTL.High removal efficiencies of91.5%and92.8%were achieved for Cationic Red GTL and Crystal Violet,respectively,in wastewater,and the efficiency remained high after seven cycles.However,almost no degradation of Acid Red occurred in the CWAO process.Furthermore,hydroxyl radicals were formed in the CWAO process,which induced the decomposition of the two cationic dyes in wastewater,and the toxicity of their effluents was decreased after degradation.The results indicate that the Mo‐Cu‐Fe‐O composite shows excellent catalytic activity for the treatment of wastewater contaminated with cationic dyes.展开更多
To select the proper composition and obtain an overall material?microstructure?property relationship for Cu?Fe alloy, theeffect of Fe content on microstructure and properties of Cu?Fe-based composite coatings by laser...To select the proper composition and obtain an overall material?microstructure?property relationship for Cu?Fe alloy, theeffect of Fe content on microstructure and properties of Cu?Fe-based composite coatings by laser induction hybrid rapid claddingwas investigated. Microstructure characterization of the composite coatings was tested utilizing SEM, XRD and EDS. Microhardnessmeasurement was executed to evaluate the mechanical properties of the composite coatings. The results show that for low Fe content,the composite coating presents a feature that Fe-rich equiaxed dendrites are embedded in the Cu-rich matrix. With increasing Fecontent, the Fe-rich particles are dispersed in the Cu-rich matrix. With further increasing Fe content, large amounts of Cu-richparticles are homogeneously dispersed in the interdendrite of the Fe-rich matrix. Correspondingly, the average microhardness of thecomposite coatings increases gradually with the increase of Fe content and the microhardness of Cu14.5Fe83Si2C0.5 coating is muchtwice higher than that of the substrate.展开更多
The effects of intermediate annealings on the microstructure, the strength and the electrical resistivity of deformation-processed Cu-Fe in-situ composites were studied. The results show that intermediate annealings f...The effects of intermediate annealings on the microstructure, the strength and the electrical resistivity of deformation-processed Cu-Fe in-situ composites were studied. The results show that intermediate annealings favour the formation of uniform tiny fibres from the iron dendrites but they have no obvious effect on the strength of the composite. The bigger the strain is, the higher the strength is. As the strain increases, the resistivity increases due to the increase of interface density. Intermediate annealings result in notable decreasing resistivity due to the precipitation of the iron atoms from the Cu matrix and decrease of solute scattering resistivity. The doping with Zr improves the strength of the composite slightly and the ultimate tensile strength(UTS) increases about 10%. The colligated performances of deformation-processed Cu-11.5%Fe and Cu- 11.5%Fe-Zr composites at strain η= 5.37 are 64.6% IACS/752MPa and 61.4% IACS/824MPa respectively.展开更多
The strength of the deformation-processed Cu-Fe in-situ composite was conducted by material test system(MTS). The results show that the strength increases with the increasing deformation strain and iron content,which ...The strength of the deformation-processed Cu-Fe in-situ composite was conducted by material test system(MTS). The results show that the strength increases with the increasing deformation strain and iron content,which is greater than that of the calculated value based on the rule of mixture. The mechanism of strengthening was analysed and evidenced by interface barrier. The correlation between the strength and the thickness of copper phase (tcu) obeys Hall-Petch relationship and can be described well by geometrical necessary dislocation model and interface as dislocation source model.展开更多
Influence of different extrusion pressures and pouring temperatures on comprehensive performance of(Al63Cu25Fe12)p/ZL101 composites is studied in this paper.The results show that the tensile strength,elongation and ha...Influence of different extrusion pressures and pouring temperatures on comprehensive performance of(Al63Cu25Fe12)p/ZL101 composites is studied in this paper.The results show that the tensile strength,elongation and hardness of(Al63Cu25Fe12)p/ZL101 composite increase with the squeezing pressure increasing from 50 MPa to 100 MPa,and gradually reduce from 100 MPa to 150 MPa.In addition,the mechanical properties of the composite can be improved with pouring temperature growing,while the temperature should not exceed 760℃.When squeezing pressure is 100 MPa and pouring temperature is 720℃,mechanical properties of composites are the best.Finally,the mechanical properties of(Al 63 Cu 25 Fe 12)p/ZL101 composite will be improved by suitable heat treatment technology展开更多
Ternary Al-4.5 (wt%) Cu-3.4 (wt%) Fe in-situ composite was prepared at 1100°C by conventional casting method. However, this particular alloy contains larger needle-shaped intermetallics of Al3Fe phase. These ...Ternary Al-4.5 (wt%) Cu-3.4 (wt%) Fe in-situ composite was prepared at 1100°C by conventional casting method. However, this particular alloy contains larger needle-shaped intermetallics of Al3Fe phase. These exert adverse effect on the mechanical properties of the alloys. The larger shape and uneven orientation of the intermetallic were found to be responsible for the degradation of properties. The main purpose of this study was to modify the geometry of those needles by adding magnesium (Mg) as a fourth material. A series of alloys were prepared by adding 4, 6, 8, 10, wt% Mg in Al-4.5 (wt%) Cu-3.4 (wt%) Fe alloy. Microstructures were observed by optical microscopy. Mechanical properties like ultimate tensile strength, % elongation, % area reduction, hardness and wear test were determined. The study revealed that Mg transformed the needles of Al3Fe into globular shape which gave the alloys better mechanical properties.展开更多
The ultrafine particles of a new style Fe-Cu-based catalysts for CO hydrogenation were prepared by impregnating the organic sol of Fe（OH）3 and Cu（OH）2 onto the activated Al2O3, in which the organic sol of Fe（OH）...The ultrafine particles of a new style Fe-Cu-based catalysts for CO hydrogenation were prepared by impregnating the organic sol of Fe（OH）3 and Cu（OH）2 onto the activated Al2O3, in which the organic sol of Fe（OH）3 and Cu（OH）2 were prepared in the microemulsion of dodecylbenzenesulfonic acid sodium（S）/n-butanol（A）/toluene（O）/water with V（A）/V（O） = 0.25 and W（A）/W（S） = 1.50. This catalyst was characterized by particle size analysis, XRD and TG. The results of particle size analysis showed that Fe（OH）3 particles with a mean size of 17.1 nm and Cu（OH）2 particles with an average size of 6.65 um were obtained. TG analysis and XRD patterns suggested that 673 K is the optimal calcination temperature. CO hydrogenation produced C＋OH with a high selectivity above 58 wt% by using the ultrafine particles as catalyst, and the total alcohol yield of 0.250 g·ml^-1 ·h^-1 was obtained when the contents of Al2O3 and K were 88.61 wt% and 1.60 wt%, respectively.展开更多
Ethanol induced method was applied to prepare Cu-Fe-Zr catalysts for conversion of syngas to higher alcohols. The catalytic performance of the catalysts induced by ethanol was superior to that of the catalyst prepared...Ethanol induced method was applied to prepare Cu-Fe-Zr catalysts for conversion of syngas to higher alcohols. The catalytic performance of the catalysts induced by ethanol was superior to that of the catalyst prepared by the conventional precipitation method. Among various procedures for ethanol induced method, it was found that incorporation of ethanol in the precipitation process was the better. After incorporation of ethanol, the crystal size of CuO decreased and the reduction of copper species became easier. The better activity of Cu-Fe-Zr catalysts prepared by ethanol induced procedures was probably caused by the higher dispersion of Cu species.展开更多
Cu-x-Fe-y/SiO2 catalysts were prepared using urea-assisted sol-gel method. The structure and physicochemical properties of the catalysts were characterized using N-2 adsorption-desorption, transmission electron micros...Cu-x-Fe-y/SiO2 catalysts were prepared using urea-assisted sol-gel method. The structure and physicochemical properties of the catalysts were characterized using N-2 adsorption-desorption, transmission electron microscopy, H-2-temperature-programmed reduction, powder X-ray diffraction, and X-ray photoelectron spectroscopy. Compared with monometallic Cu or Fe catalysts, the bimetallic Cu-x-Fe-y/SiO2 catalysts exhibited enhanced catalytic performance for the selective hydrogenation of diethyl malonate to 1,3-propanediol. The bimetallic catalyst with an optimal Cu/Fe atomic ratio of 2 exhibited the highest activity, which yielded 96.3% conversion to diethyl malonate and 93.3% selectivity to 1,3-propanediol under the optimal reaction conditions. Characterization results revealed that interactions between Cu and Fe contributed to the improvement of diethyl malonate conversion and selectivity to 1,3-propanediol. The X-ray photoelectron spectroscopy results revealed that the addition of appropriate amount of Fe species enhanced the reduction of Cu2+ species, thereby increasing the Cu-0 species on the surface of bimetallic catalyst. It led to a better chemisorption capacity of hydrogen and further promoted of the activation of hydrogen molecule. The ethyl acetate temperature-programmed desorption results indicated that the FeOx species provided the additional adsorption sites for substrate molecules, and they activated the C=O bond. The improved catalytic performance of bimetallic Cu-x-Fe-y/SiO2 catalyst was mainly attributed to the synergistic effect between Cu-0 and FeOx species. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.展开更多
MoS_(2)/CuS composite catalysts were successfully synthesized using a one-step hydrothermal method with sodium molybdate dihydrate,thiourea,oxalic acid,and copper nitrate trihydrate as raw materials.The hydrogen pro-d...MoS_(2)/CuS composite catalysts were successfully synthesized using a one-step hydrothermal method with sodium molybdate dihydrate,thiourea,oxalic acid,and copper nitrate trihydrate as raw materials.The hydrogen pro-duction performance of MoS_(2)/CuS prepared with different molar ratios of Mo to Cu precursors(n_(Mo)∶n_(Cu))as cathodic catalysts was investigated in the two-chamber microbial electrolytic cell(MEC).X-ray diffraction(XRD),X-ray pho-toelectron spectroscopy(XPS),scanning electron microscopy(SEM),transmission electron microscope(TEM),linear scanning voltammetry(LSV),electrochemical impedance analysis(EIS),and cyclic voltammetry(CV)were used to characterize the synthesized catalysts for testing and analyzing the hydrogen-producing performance.The results showed that the hydrogen evolution performance of MoS_(2)/CuS-20%(nMo∶nCu=5∶1)was better than that of platinum(Pt)mesh,and the hydrogen production rate of MoS_(2)/CuS-20%as a cathode in MEC was(0.2031±0.0237)m^(3)_(H_(2))·m^(-3)·d^(-1) for 72 h at an applied voltage of 0.8 V,which was slightly higher than that of Pt mesh of(0.1886±0.0134)m^(3)_(H_(2))·m^(-3)·d^(-1).The addition of a certain amount of CuS not only regulates the electron transfer ability of MoS_(2) but also increases the density of active sites.展开更多
In order to increase activity of Cu Fe catalyst and use the mixture of nitrogen and hydrogen directly for preparation of high alcohols by reducing fatty acid esters, rare earths were used to modify the catalyst. Expe...In order to increase activity of Cu Fe catalyst and use the mixture of nitrogen and hydrogen directly for preparation of high alcohols by reducing fatty acid esters, rare earths were used to modify the catalyst. Experiments show that yield of high alcohols increases by 3% as 1% Sm 2O 3 is added to the catalyst when the reduction is carried out under pure hydrogen. The yield greatly decreases when the reduction is carried out under the mixture of hydrogen and nitrogen. Catalysts activities modified by Y and Nd can be evidently improved and even enhanced. The yields increase by 33% and 29% when 1% Y 2O 3 and 1% Nd 2O 3 are added to the catalyst, respectively.展开更多
制备了负载在Na Y分子筛上的Fe Cu Mn Y复合催化剂,并对其在非均相UV Fe Cu Mn Y H2O2体系中催化氧化4BS染料废水进行了研究.结果表明,非均相UV Fe Cu Mn Y H2O2体系对4BS染料废水的处理具有很高的效率.在基准条件下,反应时间为20min时...制备了负载在Na Y分子筛上的Fe Cu Mn Y复合催化剂,并对其在非均相UV Fe Cu Mn Y H2O2体系中催化氧化4BS染料废水进行了研究.结果表明,非均相UV Fe Cu Mn Y H2O2体系对4BS染料废水的处理具有很高的效率.在基准条件下,反应时间为20min时,废水中4BS的去除率达到了93 7%.与均相UV Fenton体系不同,非均相UV Fe Cu Mn Y H2O2体系在碱性条件下(pH=10 5)仍可高效去除CODCr.动力学研究得到催化氧化4BS废水的模型方程,该模型可以为非均相UV Fe Cu Mn Y H2O2体系处理高色度的实际染料废水提供指导.展开更多
基金the State Key Fundamental Research Program(Ministry of Science and Technology of China,No.2011CBA00501)Shanghai Municipal Science and Technology Commission,China(Grant No:11DZ1200300)the Foundation of State Key Laboratory of Coal Conversion(Grant No:1112610)
文摘Cu-Fe composite oxides were prepared by co-precipitation method and tested for higher alcohol synthesis from syngas. The selectivity to C2＋OH and C6＋OH in alcohol distribution was very high while the methane product fraction in hydrocarbon distribution was rather low, demonstrating a promising potential in higher alcohols synthesis from syngas. The distribution of alcohols and hydrocarbons approximately obeyed Anderson-Schulz-Flory distribution with similar chain growth probability, indicating alcohols and hydrocarbons derived from the same intermediates. The effects of Cu/Fe molar ratio, reaction temperature and gas hourly space velocity （GHSV） on catalytic performance were studied in detail. The sample with a Cu/Fe molar ratio of 10/1 exhibited the best catalytic performance. Higher reaction temperature accelerated water-gas-shift reaction and led to lower total alcohols selectivity. GHSV showed great effect on catalytic performance and higher GHSV increased the total alcohol selectivity, indicating there existed visible dehydration reaction of alcohol into hydrocarbon.
基金supported by the National Natural Science Foundation of China(51678511,51308484)the Natural Science Foundation of Hunan Province(13JJ4049)+3 种基金the Education Department Fund of Hunan Province(14C1094)the Open Fund of Key Laboratory of Mineralogy and Metallogeny in Chinese Academy of Sciences(KLMM20150104)the Major Talent Training Program of Xiangtan University(16PYZ09)the Specialized Research Fund for the Doctoral Program of Xiangtan University(12QDZ18)~~
文摘A novel‐structured Mo‐Cu‐Fe‐O composite was successfully prepared by co‐precipitation and impregnation method.The properties of the as‐prepared samples were determined using X‐ray diffraction,temperature‐programmed reduction by H2,cyclic voltammetry,and temperature‐programmed desorption by O2.The results showed that Mo6+diffused into the Cu‐Fe‐O crystal lattice and then formed a new crystalline phase of CuMoO4.The Mo‐Cu‐Fe‐O catalyst had redox properties,and its surface contained active sites for oxygen adsorption.In addition,the catalytic activity of the Mo‐Cu‐Fe‐O composite was evaluated by the degradation of Cationic Red GTL,Crystal Violet,and Acid Red in catalytic wet air oxidation(CWAO)at ambient temperature and pressure.The Mo‐Cu‐Fe‐O catalyst showed excellent activity at basic conditions for the degradation of Cationic Red GTL.High removal efficiencies of91.5%and92.8%were achieved for Cationic Red GTL and Crystal Violet,respectively,in wastewater,and the efficiency remained high after seven cycles.However,almost no degradation of Acid Red occurred in the CWAO process.Furthermore,hydroxyl radicals were formed in the CWAO process,which induced the decomposition of the two cationic dyes in wastewater,and the toxicity of their effluents was decreased after degradation.The results indicate that the Mo‐Cu‐Fe‐O composite shows excellent catalytic activity for the treatment of wastewater contaminated with cationic dyes.
基金Projects(51471084,61475117)supported by the National Natural Science Foundation of ChinaProject(13ZCZDGX01109)supported by Tianjin Municipal Science and Technology Commission of ChinaProject(20122BBE500031)supported by the Key Technology Project of Jiangxi Province in China
文摘To select the proper composition and obtain an overall material?microstructure?property relationship for Cu?Fe alloy, theeffect of Fe content on microstructure and properties of Cu?Fe-based composite coatings by laser induction hybrid rapid claddingwas investigated. Microstructure characterization of the composite coatings was tested utilizing SEM, XRD and EDS. Microhardnessmeasurement was executed to evaluate the mechanical properties of the composite coatings. The results show that for low Fe content,the composite coating presents a feature that Fe-rich equiaxed dendrites are embedded in the Cu-rich matrix. With increasing Fecontent, the Fe-rich particles are dispersed in the Cu-rich matrix. With further increasing Fe content, large amounts of Cu-richparticles are homogeneously dispersed in the interdendrite of the Fe-rich matrix. Correspondingly, the average microhardness of thecomposite coatings increases gradually with the increase of Fe content and the microhardness of Cu14.5Fe83Si2C0.5 coating is muchtwice higher than that of the substrate.
文摘The effects of intermediate annealings on the microstructure, the strength and the electrical resistivity of deformation-processed Cu-Fe in-situ composites were studied. The results show that intermediate annealings favour the formation of uniform tiny fibres from the iron dendrites but they have no obvious effect on the strength of the composite. The bigger the strain is, the higher the strength is. As the strain increases, the resistivity increases due to the increase of interface density. Intermediate annealings result in notable decreasing resistivity due to the precipitation of the iron atoms from the Cu matrix and decrease of solute scattering resistivity. The doping with Zr improves the strength of the composite slightly and the ultimate tensile strength(UTS) increases about 10%. The colligated performances of deformation-processed Cu-11.5%Fe and Cu- 11.5%Fe-Zr composites at strain η= 5.37 are 64.6% IACS/752MPa and 61.4% IACS/824MPa respectively.
文摘The strength of the deformation-processed Cu-Fe in-situ composite was conducted by material test system(MTS). The results show that the strength increases with the increasing deformation strain and iron content,which is greater than that of the calculated value based on the rule of mixture. The mechanism of strengthening was analysed and evidenced by interface barrier. The correlation between the strength and the thickness of copper phase (tcu) obeys Hall-Petch relationship and can be described well by geometrical necessary dislocation model and interface as dislocation source model.
基金National Natural Science Foundation of China(Nos.U1610123,51674226,51574207,51574206)International Cooperation Project of the Ministry of Science and Technology of China(No.2014DFA50320)+3 种基金Science and Technology Major Project of Shanxi Province(No.MC2016-06)International Science and Technology Cooperation Project of Shanxi Province(No.2015081041)Research Project Supported by Shanxi Scholarship Council of China(No.2016-Key 2)Transformation of Scientific and Technological Achievements Special Guide Project of Shanxi Province(No.201604D131029)
文摘Influence of different extrusion pressures and pouring temperatures on comprehensive performance of(Al63Cu25Fe12)p/ZL101 composites is studied in this paper.The results show that the tensile strength,elongation and hardness of(Al63Cu25Fe12)p/ZL101 composite increase with the squeezing pressure increasing from 50 MPa to 100 MPa,and gradually reduce from 100 MPa to 150 MPa.In addition,the mechanical properties of the composite can be improved with pouring temperature growing,while the temperature should not exceed 760℃.When squeezing pressure is 100 MPa and pouring temperature is 720℃,mechanical properties of composites are the best.Finally,the mechanical properties of(Al 63 Cu 25 Fe 12)p/ZL101 composite will be improved by suitable heat treatment technology
文摘Ternary Al-4.5 (wt%) Cu-3.4 (wt%) Fe in-situ composite was prepared at 1100°C by conventional casting method. However, this particular alloy contains larger needle-shaped intermetallics of Al3Fe phase. These exert adverse effect on the mechanical properties of the alloys. The larger shape and uneven orientation of the intermetallic were found to be responsible for the degradation of properties. The main purpose of this study was to modify the geometry of those needles by adding magnesium (Mg) as a fourth material. A series of alloys were prepared by adding 4, 6, 8, 10, wt% Mg in Al-4.5 (wt%) Cu-3.4 (wt%) Fe alloy. Microstructures were observed by optical microscopy. Mechanical properties like ultimate tensile strength, % elongation, % area reduction, hardness and wear test were determined. The study revealed that Mg transformed the needles of Al3Fe into globular shape which gave the alloys better mechanical properties.
文摘The ultrafine particles of a new style Fe-Cu-based catalysts for CO hydrogenation were prepared by impregnating the organic sol of Fe（OH）3 and Cu（OH）2 onto the activated Al2O3, in which the organic sol of Fe（OH）3 and Cu（OH）2 were prepared in the microemulsion of dodecylbenzenesulfonic acid sodium（S）/n-butanol（A）/toluene（O）/water with V（A）/V（O） = 0.25 and W（A）/W（S） = 1.50. This catalyst was characterized by particle size analysis, XRD and TG. The results of particle size analysis showed that Fe（OH）3 particles with a mean size of 17.1 nm and Cu（OH）2 particles with an average size of 6.65 um were obtained. TG analysis and XRD patterns suggested that 673 K is the optimal calcination temperature. CO hydrogenation produced C＋OH with a high selectivity above 58 wt% by using the ultrafine particles as catalyst, and the total alcohol yield of 0.250 g·ml^-1 ·h^-1 was obtained when the contents of Al2O3 and K were 88.61 wt% and 1.60 wt%, respectively.
基金Natural Science Foundation of State Key Laboratory of Coal Conversion(No09-610)
文摘Ethanol induced method was applied to prepare Cu-Fe-Zr catalysts for conversion of syngas to higher alcohols. The catalytic performance of the catalysts induced by ethanol was superior to that of the catalyst prepared by the conventional precipitation method. Among various procedures for ethanol induced method, it was found that incorporation of ethanol in the precipitation process was the better. After incorporation of ethanol, the crystal size of CuO decreased and the reduction of copper species became easier. The better activity of Cu-Fe-Zr catalysts prepared by ethanol induced procedures was probably caused by the higher dispersion of Cu species.
基金supported by the Natural Science Foundation of China (91545115,21473145,and 21403178)the Postgraduate Basic Innovative Research Program of Xiamen University (201412G001)the Program for Innovative Research Team in Chinese Universities (no.IRT_14R31)
文摘Cu-x-Fe-y/SiO2 catalysts were prepared using urea-assisted sol-gel method. The structure and physicochemical properties of the catalysts were characterized using N-2 adsorption-desorption, transmission electron microscopy, H-2-temperature-programmed reduction, powder X-ray diffraction, and X-ray photoelectron spectroscopy. Compared with monometallic Cu or Fe catalysts, the bimetallic Cu-x-Fe-y/SiO2 catalysts exhibited enhanced catalytic performance for the selective hydrogenation of diethyl malonate to 1,3-propanediol. The bimetallic catalyst with an optimal Cu/Fe atomic ratio of 2 exhibited the highest activity, which yielded 96.3% conversion to diethyl malonate and 93.3% selectivity to 1,3-propanediol under the optimal reaction conditions. Characterization results revealed that interactions between Cu and Fe contributed to the improvement of diethyl malonate conversion and selectivity to 1,3-propanediol. The X-ray photoelectron spectroscopy results revealed that the addition of appropriate amount of Fe species enhanced the reduction of Cu2+ species, thereby increasing the Cu-0 species on the surface of bimetallic catalyst. It led to a better chemisorption capacity of hydrogen and further promoted of the activation of hydrogen molecule. The ethyl acetate temperature-programmed desorption results indicated that the FeOx species provided the additional adsorption sites for substrate molecules, and they activated the C=O bond. The improved catalytic performance of bimetallic Cu-x-Fe-y/SiO2 catalyst was mainly attributed to the synergistic effect between Cu-0 and FeOx species. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.
文摘MoS_(2)/CuS composite catalysts were successfully synthesized using a one-step hydrothermal method with sodium molybdate dihydrate,thiourea,oxalic acid,and copper nitrate trihydrate as raw materials.The hydrogen pro-duction performance of MoS_(2)/CuS prepared with different molar ratios of Mo to Cu precursors(n_(Mo)∶n_(Cu))as cathodic catalysts was investigated in the two-chamber microbial electrolytic cell(MEC).X-ray diffraction(XRD),X-ray pho-toelectron spectroscopy(XPS),scanning electron microscopy(SEM),transmission electron microscope(TEM),linear scanning voltammetry(LSV),electrochemical impedance analysis(EIS),and cyclic voltammetry(CV)were used to characterize the synthesized catalysts for testing and analyzing the hydrogen-producing performance.The results showed that the hydrogen evolution performance of MoS_(2)/CuS-20%(nMo∶nCu=5∶1)was better than that of platinum(Pt)mesh,and the hydrogen production rate of MoS_(2)/CuS-20%as a cathode in MEC was(0.2031±0.0237)m^(3)_(H_(2))·m^(-3)·d^(-1) for 72 h at an applied voltage of 0.8 V,which was slightly higher than that of Pt mesh of(0.1886±0.0134)m^(3)_(H_(2))·m^(-3)·d^(-1).The addition of a certain amount of CuS not only regulates the electron transfer ability of MoS_(2) but also increases the density of active sites.
文摘In order to increase activity of Cu Fe catalyst and use the mixture of nitrogen and hydrogen directly for preparation of high alcohols by reducing fatty acid esters, rare earths were used to modify the catalyst. Experiments show that yield of high alcohols increases by 3% as 1% Sm 2O 3 is added to the catalyst when the reduction is carried out under pure hydrogen. The yield greatly decreases when the reduction is carried out under the mixture of hydrogen and nitrogen. Catalysts activities modified by Y and Nd can be evidently improved and even enhanced. The yields increase by 33% and 29% when 1% Y 2O 3 and 1% Nd 2O 3 are added to the catalyst, respectively.
文摘制备了负载在Na Y分子筛上的Fe Cu Mn Y复合催化剂,并对其在非均相UV Fe Cu Mn Y H2O2体系中催化氧化4BS染料废水进行了研究.结果表明,非均相UV Fe Cu Mn Y H2O2体系对4BS染料废水的处理具有很高的效率.在基准条件下,反应时间为20min时,废水中4BS的去除率达到了93 7%.与均相UV Fenton体系不同,非均相UV Fe Cu Mn Y H2O2体系在碱性条件下(pH=10 5)仍可高效去除CODCr.动力学研究得到催化氧化4BS废水的模型方程,该模型可以为非均相UV Fe Cu Mn Y H2O2体系处理高色度的实际染料废水提供指导.
