Supported Pd catalyst is an important noble metal material in recent years due to its high catalytic performance in CO_(2)hydrogenation.A fluidized-bed plasma assisted atomic layer deposition(FP-ALD) process is report...Supported Pd catalyst is an important noble metal material in recent years due to its high catalytic performance in CO_(2)hydrogenation.A fluidized-bed plasma assisted atomic layer deposition(FP-ALD) process is reported to fabricate Pd nanoparticle catalyst over γ-Al_(2)O_(3)or Fe_(2)O_(3)/γ-Al_(2)O_(3)support,using palladium hexafluoroacetylacetonate as the Pd precursor and H_(2)plasma as counter-reactant.Scanning transmission electron microscopy exhibits that highdensity Pd nanoparticles are uniformly dispersed over Fe_(2)O_(3)/γ-Al_(2)O_(3)support with an average diameter of 4.4 nm.The deposited Pd-Fe_(2)O_(3)/γ-Al_(2)O_(3)shows excellent catalytic performance for CO_(2)hydrogenation in a dielectric barrier discharge reactor.Under a typical condition of H_(2)to CO_(2)ratio of 4 in the feed gas,the discharge power of 19.6 W,and gas hourly space velocity of10000 h^(-1),the conversion of CO_(2)is as high as 16.3% with CH_(3)OH and CH4selectivities of 26.5%and 3.9%,respectively.展开更多
The Cu-Fe/AC catalyst was prepared by microwave-assisted synthesis, and its morphological characteristics were characterized. The degradation effect of phenol wastewater by catalytic wet peroxide oxidation(CWPO) was s...The Cu-Fe/AC catalyst was prepared by microwave-assisted synthesis, and its morphological characteristics were characterized. The degradation effect of phenol wastewater by catalytic wet peroxide oxidation(CWPO) was studied, and the response surface methodology(RSM) was used to analyze the influencing factors of the removal rate of COD. The experimental results showed that under the conditions of reaction temperature 80 ℃, reaction time 90 min, initial pH 3.1 and H_(2)O_(2)addition 2.2 g/L, the removal rate of COD reached 82%. The results of response surface methodology indicated that under the conditions of reaction temperature 100 ℃, reaction time 64 min, initial pH 3.3 and H_(2)O_(2)addition 2.7 g/L, the removal rate of COD was up to 86%. After Cu-Fe/AC catalyst was reused for 4 times, the removal rate of COD was still above 80%, revealing that the catalyst showed good catalytic performance.展开更多
The development of a benign environmental catalyst for the generation of biodiesel is an area of importance to reduce the overall usage of fossil fuels. In the current work, biochar was produced by slow pyrolysis of I...The development of a benign environmental catalyst for the generation of biodiesel is an area of importance to reduce the overall usage of fossil fuels. In the current work, biochar was produced by slow pyrolysis of Irul wood sawdust. The optimization for biochar generation was carried out for different reaction temperatures and heating durations. The biochar was used to prepare solid acid catalysts by sulfonation process. The characterization of biochar and the sulfonated catalyst were carried out using Elemental analysis, Fourier Transform Infrared spectroscopy(FTIR), Powder X-ray Diffraction(XRD), Thermo Gravimetric Analysis(TGA), Scanning Electron Microscopy(SEM) and Surface area analyzer(BET). The characterization results showed that sulfonation of biochar resulted in biochar based solid acid catalyst containing various functional acidic groups like weak acidic\\OH groups, strong acidic\\COOH and SO3 H groups. The total acid density and sulfonic acid group density of catalyst were estimated and showed excellent acidic sites concentration which gives a good catalytic activity for biodiesel production through simultaneous esterification and transesterification. The enhanced catalytic activity is due to the high acid density of SO3 H groups and the reactant accessibility towards acidic sites as well as the strong affinity between the hydrophilic reactants and the neutral OH groups which are bonded with the polycyclic aromatic carbon rings. The performance of biochar catalyst for the production of biodiesel was evaluated by comparing the yield obtained. The FTIR and Gas Chromatography–Mass Spectroscopy(GC–MS) were also carried out for the analysis of biodiesel produced.展开更多
Zero or negative emissions of carbon dioxide(CO2)is the need of the times,as inexorable rising and alarming levels of CO2 in the atmosphere lead to global warming and severe climate change.The electrochemical CO2 redu...Zero or negative emissions of carbon dioxide(CO2)is the need of the times,as inexorable rising and alarming levels of CO2 in the atmosphere lead to global warming and severe climate change.The electrochemical CO2 reduction(eCO2R)to value‐added fuels and chemicals by using renewable electricity provides a cleaner and more sustainable route with economic benefits,in which the key is to develop clean and economical electrocatalysts.Carbon‐based catalyst materials possess desirable properties such as high offset potential for H2 evolution and chemical stability at the negative applied potential.Although it is still challenging to achieve highly efficient carbon‐based catalysts,considerable efforts have been devoted to overcoming the low selectivity,activity,and stability.Here,we summarize and discuss the recent progress in carbon‐based metal‐free catalysts including carbon nanotubes,carbon nanofibers,carbon nanoribbons,graphene,carbon nitride,and diamonds with an emphasis on their activity,product selectivity,and stability.In addition,the key challenges and future potential approaches for efficient eCO2R to low carbon‐based fuels are highlighted.For a good understanding of the whole history of the development of eCO2R,the CO2 reduction reactions,principles,and techniques including the role of electrolytes,electrochemical cell design and evaluation,product selectivity,and structural composition are also discussed.The metal/metal oxides decorated with carbon‐based electrocatalysts are also summarized.We aim to provide insights for further development of carbon‐based metal‐free electrocatalysts for CO2 reduction from the perspective of both fundamental understanding and technological applications in the future.展开更多
Cu-x-Fe-y/SiO2 catalysts were prepared using urea-assisted sol-gel method. The structure and physicochemical properties of the catalysts were characterized using N-2 adsorption-desorption, transmission electron micros...Cu-x-Fe-y/SiO2 catalysts were prepared using urea-assisted sol-gel method. The structure and physicochemical properties of the catalysts were characterized using N-2 adsorption-desorption, transmission electron microscopy, H-2-temperature-programmed reduction, powder X-ray diffraction, and X-ray photoelectron spectroscopy. Compared with monometallic Cu or Fe catalysts, the bimetallic Cu-x-Fe-y/SiO2 catalysts exhibited enhanced catalytic performance for the selective hydrogenation of diethyl malonate to 1,3-propanediol. The bimetallic catalyst with an optimal Cu/Fe atomic ratio of 2 exhibited the highest activity, which yielded 96.3% conversion to diethyl malonate and 93.3% selectivity to 1,3-propanediol under the optimal reaction conditions. Characterization results revealed that interactions between Cu and Fe contributed to the improvement of diethyl malonate conversion and selectivity to 1,3-propanediol. The X-ray photoelectron spectroscopy results revealed that the addition of appropriate amount of Fe species enhanced the reduction of Cu2+ species, thereby increasing the Cu-0 species on the surface of bimetallic catalyst. It led to a better chemisorption capacity of hydrogen and further promoted of the activation of hydrogen molecule. The ethyl acetate temperature-programmed desorption results indicated that the FeOx species provided the additional adsorption sites for substrate molecules, and they activated the C=O bond. The improved catalytic performance of bimetallic Cu-x-Fe-y/SiO2 catalyst was mainly attributed to the synergistic effect between Cu-0 and FeOx species. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.展开更多
The nano ZrO2-supported copper-based catalysts for methane combustion were investigated by means of N2 adsorption, TEM, XRD, H2-TPR techniques and the test of methane oxidation. Two kinds of ZrO2 were used as support,...The nano ZrO2-supported copper-based catalysts for methane combustion were investigated by means of N2 adsorption, TEM, XRD, H2-TPR techniques and the test of methane oxidation. Two kinds of ZrO2 were used as support, one (ZrO2-1) was obtained from the commercial ZrO2 and the other (ZrO2-2) was issued from the thermal decomposition of zirconium nitrate. It was found that the CuO/ZrO2-2 catalyst was more active than CuO/ZrO2-1. N2 adsorption, H2-TPR and XRD measurements showed that larger surface area, better reduction property, presence of tetragonal ZrO2 and higher dispersion of active component for CuO/ZrO2-2 than that of CuO/ZrO2-1. These factors could be the dominating reasons for its higher activity for methane combustion.展开更多
Catalysts Cu Ox/γ-Al_2O_3-IH and Cu Ox/γ-Al_2O_3-IM were prepared, characterized, and tested for styrene combustion in the absence and presence of water vapor. The effect of copper valence of the catalysts on the ca...Catalysts Cu Ox/γ-Al_2O_3-IH and Cu Ox/γ-Al_2O_3-IM were prepared, characterized, and tested for styrene combustion in the absence and presence of water vapor. The effect of copper valence of the catalysts on the catalytic activity for styrene combustion was discussed using the theory of hard soft acids and bases(HSAB).The results showed that the existence of water vapor in feed stream inhibited the catalytic activity for styrene combustion due to the competition adsorption of water molecule. HSAB theory confirmed that the local soft acidity of the catalyst Cu Ox/γ-Al_2O_3-IH was much stronger than that of the catalyst Cu Ox/γ-Al_2O_3-IM because of the higher content of soft acid Cu+on its surface, which increased the adsorption ability toward soft base of styrene and reduced the adsorption toward hard base of water vapor, and thus increased the catalytic activity for styrene combustion and weakened the negative influence of water vapor.展开更多
A series of Ni/SBA-15 catalysts with Ni contents ranging from 5wt% to 20wt% as well as 10wt%Ni/10wt%CexZr1-xO2/SBA-15 (x=0, 0.5, 1) were prepared. The structures of the catalysts were characterized using XRD, TPR, T...A series of Ni/SBA-15 catalysts with Ni contents ranging from 5wt% to 20wt% as well as 10wt%Ni/10wt%CexZr1-xO2/SBA-15 (x=0, 0.5, 1) were prepared. The structures of the catalysts were characterized using XRD, TPR, TEM and BET techniques. The catalytic activities of the catalysts for steam reforming of methane were evaluated in a continuous flow microreactor. The results indicated that both the Ni/SBA-15 and the Ni/CexZr1-xO2/SBA-15 catalysts had good catalytic activities at at- mospheric pressure. The 10wt%Ni/SBA-15 catalyst exhibited excellent stability at 800 ℃ for time on stream of 740 h. After the reaction, carbon deposits were not formed on the surface of the catalyst. There existed a regular hexagonal mesoporous structure in the Ni/SBA-15 and the Ni/CexZr1-xO2/SBA-15 catalysts. The nickel species and the CexZr1-xO2 component were all confined in the SBA-15 mesopores. The CexZr1-xO2 could promote dispersion of the nickel species in the Ni/CexZr1-xO2/SBA-15 catalysts.展开更多
The copper based catalysts,CuO/γ-Al2O3,CuO/γ-Al2O3-cordierite(Cord) and CuO/Cord,were prepared by impregnation method.The catalytic activity of the catalysts was tested in absence and presence of water vapor,and the...The copper based catalysts,CuO/γ-Al2O3,CuO/γ-Al2O3-cordierite(Cord) and CuO/Cord,were prepared by impregnation method.The catalytic activity of the catalysts was tested in absence and presence of water vapor,and the catalysts were characterized.Temperature program desorption (TPD) experiments of toluene and water on the catalysts were carried out.The influence of water vapor on the activity of the catalysts was discussed.Results showed that addition of the water vapor has a significant negative effect on the catalytic activity of the catalysts.The higher the concentration of the water vapor in feed steam was,the lower the catalytic activity of the copper based catalysts became,which could be mainly ascribed to the competition of water molecules with toluene molecules for adsorption on the catalyst surfaces.TPD experiments showed that the strength of the interaction between water molecules and three catalysts followed the order:CuO/γ-Al2O3>CuO/γ-Al2O3-Cord>CuO/Cord.As a consequence of that,the degree of degradation in the catalytic activity of these three catalysts by the water vapor followed the order:CuO/γ-Al2O3>CuO/γ-Al2O3-Cord>CuO/Cord.However,the negative effect of the water vapor was reversible.展开更多
The ultrafine particles of a new style Fe-Cu-based catalysts for CO hydrogenation were prepared by impregnating the organic sol of Fe(OH)3 and Cu(OH)2 onto the activated Al2O3, in which the organic sol of Fe(OH)...The ultrafine particles of a new style Fe-Cu-based catalysts for CO hydrogenation were prepared by impregnating the organic sol of Fe(OH)3 and Cu(OH)2 onto the activated Al2O3, in which the organic sol of Fe(OH)3 and Cu(OH)2 were prepared in the microemulsion of dodecylbenzenesulfonic acid sodium(S)/n-butanol(A)/toluene(O)/water with V(A)/V(O) = 0.25 and W(A)/W(S) = 1.50. This catalyst was characterized by particle size analysis, XRD and TG. The results of particle size analysis showed that Fe(OH)3 particles with a mean size of 17.1 nm and Cu(OH)2 particles with an average size of 6.65 um were obtained. TG analysis and XRD patterns suggested that 673 K is the optimal calcination temperature. CO hydrogenation produced C+OH with a high selectivity above 58 wt% by using the ultrafine particles as catalyst, and the total alcohol yield of 0.250 g·ml^-1 ·h^-1 was obtained when the contents of Al2O3 and K were 88.61 wt% and 1.60 wt%, respectively.展开更多
A systematic study was undertaken to investigate the effects of the manganese incorporation manner on the textural properties, bulk and surface phase compositions, reduction/carburization behaviors, and surface basici...A systematic study was undertaken to investigate the effects of the manganese incorporation manner on the textural properties, bulk and surface phase compositions, reduction/carburization behaviors, and surface basicity of an iron-based Fischer-Tropsch synthesis (FTS) catalyst. The catalyst samples were characterized by N2 physisorption, X-ray photoelectron spectroscopy (XPS), H2 (or CO) temperature-programmed reduction (TPR), CO2 temperature-programmed desorption (TPD), and M5ssbauer spectroscopy. The FTS performance of the catalysts was studied in a slurry-phase continuously stirred tank reactor (CSTR). The characterization results indicated that the manganese promoter incorporated by using the coprecipitation method could improve the dispersion of iron oxide, and decrease the size of the iron oxide crystallite. The manganese incorporated with the impregnation method is enriched on the catalyst's surface. The manganese promoter added with the impregnation method suppresses the reduction and carburization of the catalyst in H2, CO, and syngas because of the excessive enrichment of manganese on the catalyst surface. The catalyst added manganese using the coprecipitation method has the highest CO conversion (51.9%) and the lowest selectivity for heavy hydrocarbons (C12+).展开更多
With oil-soluble molybdenum compound and sublimed sulfur serving as raw materials, two dispersed Mo-based catalysts were prepared, characterized and then applied to the hydrogenation conversion of phenanthrene. The te...With oil-soluble molybdenum compound and sublimed sulfur serving as raw materials, two dispersed Mo-based catalysts were prepared, characterized and then applied to the hydrogenation conversion of phenanthrene. The test results showed that under the conditions specified by this study, the catalyst prepared in a higher sulfiding atmosphere was more catalytically active due to its higher content of MoS2 and stronger intrinsic catalytic activity of MoS2 unit, which demonstrated that the sulfiding atmosphere for the preparation of catalysts not only could influence the yield of MoS2 but also the structure of MoS2.The analysis on the selectivity of octahydrophenanthrene isomers revealed that the catalyst prepared in a lower sulfiding atmosphere had a relatively higher catalytic selectivity to the hydrogenation of outer aromatic ring and the structure of catalysts could be modified under the specific reaction conditions. Moreover, the selectivity between the isomers of as-octahydrophenanthrene at different reaction time and temperature was analyzed and, based on the results, a hydrogenation mechanism over dispersed Mo-based catalysts was suggested, with monatomic hydrogen transfer and catalytic surface desorption of the half-addition intermediates functioning as the key points. In addition, it is concluded that the catalyst prepared in a lower sulfiding atmosphere was more capable of adsorption than the other one.展开更多
A series of iron-based Fischer-Tropsch synthesis (FTS) catalysts incorporated with Al2O3 binder were prepared by the combination of co-precipitation and spray drying technology. The catalyst samples were characteriz...A series of iron-based Fischer-Tropsch synthesis (FTS) catalysts incorporated with Al2O3 binder were prepared by the combination of co-precipitation and spray drying technology. The catalyst samples were characterized by using N2 physical adsorption, temperature-programmed reduction/desorption (TPR/TPD) and MSssbauer effect spectroscopy (MES) methods. The characterization results indicated that the BET surface area increases with increasing Al2O3 content and passes through a maximum at the Al2O3/Fe ratio of 10/100 (weight basis). After the point, it decreases with further increase in Al2O3 content. The incorporation of Al2O3 binder was found to weaken the surface basicity and suppress the reduction and carburization of iron-based catalysts probably due to the strong K-Al2O3 and Fe-Al2O3 interactions. Furthermore, the H2 adsorption ability of the catalysts is enhanced with increasing Al2O3 content. The FTS performances of the catalysts were tested in a slurry-phase continuously stirred tank reactor (CSTR) under the reaction conditions of 260 ℃, 1.5 MPa, 1000 h^-1 and molar ratio of H2/CO 0.67 for 200 h. The results showed that the addition of small amounts of Al2O3 affects the activity of iron-based catalysts to a little extent. However, with further increase of Al2O3 content, the FTS activity and water gas shift reaction (WGS) activity are decreased severely. The addition of appropriate Al2O3 do not affect the product selectivity, but the catalysts incorporated with large amounts of Al2O3 have higher selectivity for light hydrocarbons and lower selectivity for heavy hydrocarbons.展开更多
The nickel-based catalysts were prepared by the sol-gel method and used for the CH4 reforming with CO2. The effects of the sol-gel method on the specific surface area, catalytic activity, desorption, and reduction per...The nickel-based catalysts were prepared by the sol-gel method and used for the CH4 reforming with CO2. The effects of the sol-gel method on the specific surface area, catalytic activity, desorption, and reduction performances of catalysts were investigated with BET, TPR, and TPD. Compared with the catalyst prepared by the impregnation method, the results indicated that the catalysts prepared by the sol-gel method had larger specific surface area, showing higher catalytic activities and exhibiting perfect desorption and reduction performances. In addition, the modification effects of adding La were studied, and it was found that the 0.75NLBT catalyst constituted of 5wt.%Ni-0.75wt.%La was optimal.展开更多
A series of Ni/SBA-15 catalysts with 5wt% to 15wt% Ni content as well as a series of 12.5%Ni/Cu/SBA-15 catalysts with 1% to 10% copper content were prepared by the impregnation method. The catalytic performance for pa...A series of Ni/SBA-15 catalysts with 5wt% to 15wt% Ni content as well as a series of 12.5%Ni/Cu/SBA-15 catalysts with 1% to 10% copper content were prepared by the impregnation method. The catalytic performance for partial oxidation of methane was investigated in a continuous flow microreactor under atmospheric pressure. The textural and chemical properties of the catalysts were characterized by XRD, TEM, BET and Hz-TPR techniques. The results indicated that the catalysts modified with Cu promoter showed better performance than those without modification. For the 12.5%Ni/2.5%/Cu/SBA-15 catalyst, at 850 ℃ the conversion of CH4 reached 97.9% and the selectivity of CO and H2 reached 98.0% and 96.0%, respectively. In XRD patterns of the Ni/Cu/SBA-15 catalyst with 7.5 to 10% Cu contents there were CuO characteristic peaks beside NiO characteristic peaks. The mesoporous structure of SBA-15 was retained in all of the catalysts. TPR analysis of the catalysts revealed that a strong interaction between Ni, Cu promoter and SBA-15 support may be existed. This interaction enhanced significantly the redox properties of the catalysts resulting in the higher catalytic activity.展开更多
Highly active and selective Ni-based catalysts for partial oxidation of methane (POM) to syngas (CO/H,) have been studied and developed. Spectroscopic characterization by XRD, XPS, EPR, etc. demonstrated that under th...Highly active and selective Ni-based catalysts for partial oxidation of methane (POM) to syngas (CO/H,) have been studied and developed. Spectroscopic characterization by XRD, XPS, EPR, etc. demonstrated that under the POM reaction conditions, the Ni-components of the catalysts investigated were reduced and enriched on the surface to form metallic Ni0-phase. A comparative study of the first series of transition-metals showed that only Ni and Co have a high POM activity and selectivity, whereas the others (including Mn, Fe, Cu, etc. ) give mainly complete combustion products, Co, and H2O. The results favor the following viewpoints: the PoM activity is related with the rapidly changeable valence transitionmetal sites, M0/M2+ (e. g. Ni0/Ni2+ ), on the surface of the functioning catalysts;the transition-metal sites in zero-valence state seem to be responsible for the activation and dehydrogenation of methane by homolytic splitting of its C-H bonds on these sites. and the nature of rapidly changeable valence of the active sties is requisite for activation and rapid conversion of dioxygen.展开更多
A series of Ni/SBA-15 catalysts with Ni contents from 7.5 wt% to 15 wt% were prepared by impregnation method.The effect of O2 and H2O on the combined reforming of the simulated biogas to syngas was investigated in a c...A series of Ni/SBA-15 catalysts with Ni contents from 7.5 wt% to 15 wt% were prepared by impregnation method.The effect of O2 and H2O on the combined reforming of the simulated biogas to syngas was investigated in a continuous flow fixed-bed micro-reactor.The stability of the catalyst was tested at 800 ?C.The results indicated that 10wt%Ni/SBA-15 catalyst exhibited the highest catalytic activities for the combined reforming of the simulated biogas to syngas.Under the reaction conditions of the feed gas molar ratios CH4/CO2/O2/H2O = 2/1/0.6/0.6,GHSV = 24000 ml·gcat^-1·h^-1 and the reaction temperature T = 800 ℃,the conversions of CH4 and CO2 were 92.8% and 76.3%,respectively,and the yields of CO and H2 were 99.0% and 82.0%,respectively.The catalytic activities of the catalyst did not decrease obviously after 100 h reaction time on stream.展开更多
Various Cu/ZnO/Al2O3 catalysts have been synthesized by different aluminum emulsions as aluminum sources and their pertormances tor methanol synthesis from syngas have been investigated. The influences of preparation ...Various Cu/ZnO/Al2O3 catalysts have been synthesized by different aluminum emulsions as aluminum sources and their pertormances tor methanol synthesis from syngas have been investigated. The influences of preparation methods of aluminum emulsions on physicochemical and catalytic properties of catalysts were studied by XRD, SEM, XPS,N2 adsorption-desorption techniques and methanol synthesis from syngas. The preparation methods of aluminum emulsions were found to influence the catalytic activity, CuO crystallite size, surface area and Cu0 surface area and reduction process. The results show that the catalyst CN using the aluminum source prepared by addition the ammonia into the aluminum nitrate (NP) exhibited the best catalytic performance for methanol synthesis from syngas.展开更多
基金financially supported by National Natural Science Foundation of China (Nos. 12075032 and 12105021)Beijing Municipal Natural Science Foundation (Nos.8222055 and 2232061)+1 种基金Yunnan Police College Project (No. YJKF002)Beijing Institute of Graphic Communication Project (No. Ec202207)。
文摘Supported Pd catalyst is an important noble metal material in recent years due to its high catalytic performance in CO_(2)hydrogenation.A fluidized-bed plasma assisted atomic layer deposition(FP-ALD) process is reported to fabricate Pd nanoparticle catalyst over γ-Al_(2)O_(3)or Fe_(2)O_(3)/γ-Al_(2)O_(3)support,using palladium hexafluoroacetylacetonate as the Pd precursor and H_(2)plasma as counter-reactant.Scanning transmission electron microscopy exhibits that highdensity Pd nanoparticles are uniformly dispersed over Fe_(2)O_(3)/γ-Al_(2)O_(3)support with an average diameter of 4.4 nm.The deposited Pd-Fe_(2)O_(3)/γ-Al_(2)O_(3)shows excellent catalytic performance for CO_(2)hydrogenation in a dielectric barrier discharge reactor.Under a typical condition of H_(2)to CO_(2)ratio of 4 in the feed gas,the discharge power of 19.6 W,and gas hourly space velocity of10000 h^(-1),the conversion of CO_(2)is as high as 16.3% with CH_(3)OH and CH4selectivities of 26.5%and 3.9%,respectively.
文摘The Cu-Fe/AC catalyst was prepared by microwave-assisted synthesis, and its morphological characteristics were characterized. The degradation effect of phenol wastewater by catalytic wet peroxide oxidation(CWPO) was studied, and the response surface methodology(RSM) was used to analyze the influencing factors of the removal rate of COD. The experimental results showed that under the conditions of reaction temperature 80 ℃, reaction time 90 min, initial pH 3.1 and H_(2)O_(2)addition 2.2 g/L, the removal rate of COD reached 82%. The results of response surface methodology indicated that under the conditions of reaction temperature 100 ℃, reaction time 64 min, initial pH 3.3 and H_(2)O_(2)addition 2.7 g/L, the removal rate of COD was up to 86%. After Cu-Fe/AC catalyst was reused for 4 times, the removal rate of COD was still above 80%, revealing that the catalyst showed good catalytic performance.
基金Supported by TEQIP-II sanctioned under NITC/TEQIP-II/R&D/2015-16,National Institute of Technology Calicut
文摘The development of a benign environmental catalyst for the generation of biodiesel is an area of importance to reduce the overall usage of fossil fuels. In the current work, biochar was produced by slow pyrolysis of Irul wood sawdust. The optimization for biochar generation was carried out for different reaction temperatures and heating durations. The biochar was used to prepare solid acid catalysts by sulfonation process. The characterization of biochar and the sulfonated catalyst were carried out using Elemental analysis, Fourier Transform Infrared spectroscopy(FTIR), Powder X-ray Diffraction(XRD), Thermo Gravimetric Analysis(TGA), Scanning Electron Microscopy(SEM) and Surface area analyzer(BET). The characterization results showed that sulfonation of biochar resulted in biochar based solid acid catalyst containing various functional acidic groups like weak acidic\\OH groups, strong acidic\\COOH and SO3 H groups. The total acid density and sulfonic acid group density of catalyst were estimated and showed excellent acidic sites concentration which gives a good catalytic activity for biodiesel production through simultaneous esterification and transesterification. The enhanced catalytic activity is due to the high acid density of SO3 H groups and the reactant accessibility towards acidic sites as well as the strong affinity between the hydrophilic reactants and the neutral OH groups which are bonded with the polycyclic aromatic carbon rings. The performance of biochar catalyst for the production of biodiesel was evaluated by comparing the yield obtained. The FTIR and Gas Chromatography–Mass Spectroscopy(GC–MS) were also carried out for the analysis of biodiesel produced.
基金The authors thank the financial support from the“Scientific and Technical Innovation Action Plan”Basic Research Field of the Shanghai Science and Technology Committee(19JC1410500)the Fundamental ResearchFunds for the Central Universities(2232018A3‐06)the National Natural Science Foundation of China(91645110).
文摘Zero or negative emissions of carbon dioxide(CO2)is the need of the times,as inexorable rising and alarming levels of CO2 in the atmosphere lead to global warming and severe climate change.The electrochemical CO2 reduction(eCO2R)to value‐added fuels and chemicals by using renewable electricity provides a cleaner and more sustainable route with economic benefits,in which the key is to develop clean and economical electrocatalysts.Carbon‐based catalyst materials possess desirable properties such as high offset potential for H2 evolution and chemical stability at the negative applied potential.Although it is still challenging to achieve highly efficient carbon‐based catalysts,considerable efforts have been devoted to overcoming the low selectivity,activity,and stability.Here,we summarize and discuss the recent progress in carbon‐based metal‐free catalysts including carbon nanotubes,carbon nanofibers,carbon nanoribbons,graphene,carbon nitride,and diamonds with an emphasis on their activity,product selectivity,and stability.In addition,the key challenges and future potential approaches for efficient eCO2R to low carbon‐based fuels are highlighted.For a good understanding of the whole history of the development of eCO2R,the CO2 reduction reactions,principles,and techniques including the role of electrolytes,electrochemical cell design and evaluation,product selectivity,and structural composition are also discussed.The metal/metal oxides decorated with carbon‐based electrocatalysts are also summarized.We aim to provide insights for further development of carbon‐based metal‐free electrocatalysts for CO2 reduction from the perspective of both fundamental understanding and technological applications in the future.
基金supported by the Natural Science Foundation of China (91545115,21473145,and 21403178)the Postgraduate Basic Innovative Research Program of Xiamen University (201412G001)the Program for Innovative Research Team in Chinese Universities (no.IRT_14R31)
文摘Cu-x-Fe-y/SiO2 catalysts were prepared using urea-assisted sol-gel method. The structure and physicochemical properties of the catalysts were characterized using N-2 adsorption-desorption, transmission electron microscopy, H-2-temperature-programmed reduction, powder X-ray diffraction, and X-ray photoelectron spectroscopy. Compared with monometallic Cu or Fe catalysts, the bimetallic Cu-x-Fe-y/SiO2 catalysts exhibited enhanced catalytic performance for the selective hydrogenation of diethyl malonate to 1,3-propanediol. The bimetallic catalyst with an optimal Cu/Fe atomic ratio of 2 exhibited the highest activity, which yielded 96.3% conversion to diethyl malonate and 93.3% selectivity to 1,3-propanediol under the optimal reaction conditions. Characterization results revealed that interactions between Cu and Fe contributed to the improvement of diethyl malonate conversion and selectivity to 1,3-propanediol. The X-ray photoelectron spectroscopy results revealed that the addition of appropriate amount of Fe species enhanced the reduction of Cu2+ species, thereby increasing the Cu-0 species on the surface of bimetallic catalyst. It led to a better chemisorption capacity of hydrogen and further promoted of the activation of hydrogen molecule. The ethyl acetate temperature-programmed desorption results indicated that the FeOx species provided the additional adsorption sites for substrate molecules, and they activated the C=O bond. The improved catalytic performance of bimetallic Cu-x-Fe-y/SiO2 catalyst was mainly attributed to the synergistic effect between Cu-0 and FeOx species. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.
文摘The nano ZrO2-supported copper-based catalysts for methane combustion were investigated by means of N2 adsorption, TEM, XRD, H2-TPR techniques and the test of methane oxidation. Two kinds of ZrO2 were used as support, one (ZrO2-1) was obtained from the commercial ZrO2 and the other (ZrO2-2) was issued from the thermal decomposition of zirconium nitrate. It was found that the CuO/ZrO2-2 catalyst was more active than CuO/ZrO2-1. N2 adsorption, H2-TPR and XRD measurements showed that larger surface area, better reduction property, presence of tetragonal ZrO2 and higher dispersion of active component for CuO/ZrO2-2 than that of CuO/ZrO2-1. These factors could be the dominating reasons for its higher activity for methane combustion.
基金Supported by the National Natural Science Foundation of China(21366008)the Foundation of Guizhou University((2010)040)the Science & Technology Foundation of Guizhou Province((2012)2152)
文摘Catalysts Cu Ox/γ-Al_2O_3-IH and Cu Ox/γ-Al_2O_3-IM were prepared, characterized, and tested for styrene combustion in the absence and presence of water vapor. The effect of copper valence of the catalysts on the catalytic activity for styrene combustion was discussed using the theory of hard soft acids and bases(HSAB).The results showed that the existence of water vapor in feed stream inhibited the catalytic activity for styrene combustion due to the competition adsorption of water molecule. HSAB theory confirmed that the local soft acidity of the catalyst Cu Ox/γ-Al_2O_3-IH was much stronger than that of the catalyst Cu Ox/γ-Al_2O_3-IM because of the higher content of soft acid Cu+on its surface, which increased the adsorption ability toward soft base of styrene and reduced the adsorption toward hard base of water vapor, and thus increased the catalytic activity for styrene combustion and weakened the negative influence of water vapor.
基金Financial funds from the Chinese Natural Science Foundation(Project No.20473009)the Beijing Natural Science Foundation(Project No.8062023)+1 种基金the National Basic Research Program of China(Project No.2005CB221405)the National"863"Project of China(No.2006 AA10Z425)are gratefully acknowledged.
文摘A series of Ni/SBA-15 catalysts with Ni contents ranging from 5wt% to 20wt% as well as 10wt%Ni/10wt%CexZr1-xO2/SBA-15 (x=0, 0.5, 1) were prepared. The structures of the catalysts were characterized using XRD, TPR, TEM and BET techniques. The catalytic activities of the catalysts for steam reforming of methane were evaluated in a continuous flow microreactor. The results indicated that both the Ni/SBA-15 and the Ni/CexZr1-xO2/SBA-15 catalysts had good catalytic activities at at- mospheric pressure. The 10wt%Ni/SBA-15 catalyst exhibited excellent stability at 800 ℃ for time on stream of 740 h. After the reaction, carbon deposits were not formed on the surface of the catalyst. There existed a regular hexagonal mesoporous structure in the Ni/SBA-15 and the Ni/CexZr1-xO2/SBA-15 catalysts. The nickel species and the CexZr1-xO2 component were all confined in the SBA-15 mesopores. The CexZr1-xO2 could promote dispersion of the nickel species in the Ni/CexZr1-xO2/SBA-15 catalysts.
基金Supported by the National-Natural Science Foundation of China (20936001), the Natural Science Foundation of Guangdong Province, and the State Key Lab of Subtropical Building Science, South China University of Technology (x2yj C709028Z).
文摘The copper based catalysts,CuO/γ-Al2O3,CuO/γ-Al2O3-cordierite(Cord) and CuO/Cord,were prepared by impregnation method.The catalytic activity of the catalysts was tested in absence and presence of water vapor,and the catalysts were characterized.Temperature program desorption (TPD) experiments of toluene and water on the catalysts were carried out.The influence of water vapor on the activity of the catalysts was discussed.Results showed that addition of the water vapor has a significant negative effect on the catalytic activity of the catalysts.The higher the concentration of the water vapor in feed steam was,the lower the catalytic activity of the copper based catalysts became,which could be mainly ascribed to the competition of water molecules with toluene molecules for adsorption on the catalyst surfaces.TPD experiments showed that the strength of the interaction between water molecules and three catalysts followed the order:CuO/γ-Al2O3>CuO/γ-Al2O3-Cord>CuO/Cord.As a consequence of that,the degree of degradation in the catalytic activity of these three catalysts by the water vapor followed the order:CuO/γ-Al2O3>CuO/γ-Al2O3-Cord>CuO/Cord.However,the negative effect of the water vapor was reversible.
文摘The ultrafine particles of a new style Fe-Cu-based catalysts for CO hydrogenation were prepared by impregnating the organic sol of Fe(OH)3 and Cu(OH)2 onto the activated Al2O3, in which the organic sol of Fe(OH)3 and Cu(OH)2 were prepared in the microemulsion of dodecylbenzenesulfonic acid sodium(S)/n-butanol(A)/toluene(O)/water with V(A)/V(O) = 0.25 and W(A)/W(S) = 1.50. This catalyst was characterized by particle size analysis, XRD and TG. The results of particle size analysis showed that Fe(OH)3 particles with a mean size of 17.1 nm and Cu(OH)2 particles with an average size of 6.65 um were obtained. TG analysis and XRD patterns suggested that 673 K is the optimal calcination temperature. CO hydrogenation produced C+OH with a high selectivity above 58 wt% by using the ultrafine particles as catalyst, and the total alcohol yield of 0.250 g·ml^-1 ·h^-1 was obtained when the contents of Al2O3 and K were 88.61 wt% and 1.60 wt%, respectively.
基金Foundation item:the National Natural Science Foundation of China(20590360)the Natural Science Foundation of Shanxi Province(2006021014)+1 种基金the National Outstanding Young Scientists Foundation of China(20625620)National Key Basic Research Program of China(973 Program)(2007CB216401).
文摘A systematic study was undertaken to investigate the effects of the manganese incorporation manner on the textural properties, bulk and surface phase compositions, reduction/carburization behaviors, and surface basicity of an iron-based Fischer-Tropsch synthesis (FTS) catalyst. The catalyst samples were characterized by N2 physisorption, X-ray photoelectron spectroscopy (XPS), H2 (or CO) temperature-programmed reduction (TPR), CO2 temperature-programmed desorption (TPD), and M5ssbauer spectroscopy. The FTS performance of the catalysts was studied in a slurry-phase continuously stirred tank reactor (CSTR). The characterization results indicated that the manganese promoter incorporated by using the coprecipitation method could improve the dispersion of iron oxide, and decrease the size of the iron oxide crystallite. The manganese incorporated with the impregnation method is enriched on the catalyst's surface. The manganese promoter added with the impregnation method suppresses the reduction and carburization of the catalyst in H2, CO, and syngas because of the excessive enrichment of manganese on the catalyst surface. The catalyst added manganese using the coprecipitation method has the highest CO conversion (51.9%) and the lowest selectivity for heavy hydrocarbons (C12+).
基金the financial support from the National Basic Research Program of China (Grant 2012CB224801)
文摘With oil-soluble molybdenum compound and sublimed sulfur serving as raw materials, two dispersed Mo-based catalysts were prepared, characterized and then applied to the hydrogenation conversion of phenanthrene. The test results showed that under the conditions specified by this study, the catalyst prepared in a higher sulfiding atmosphere was more catalytically active due to its higher content of MoS2 and stronger intrinsic catalytic activity of MoS2 unit, which demonstrated that the sulfiding atmosphere for the preparation of catalysts not only could influence the yield of MoS2 but also the structure of MoS2.The analysis on the selectivity of octahydrophenanthrene isomers revealed that the catalyst prepared in a lower sulfiding atmosphere had a relatively higher catalytic selectivity to the hydrogenation of outer aromatic ring and the structure of catalysts could be modified under the specific reaction conditions. Moreover, the selectivity between the isomers of as-octahydrophenanthrene at different reaction time and temperature was analyzed and, based on the results, a hydrogenation mechanism over dispersed Mo-based catalysts was suggested, with monatomic hydrogen transfer and catalytic surface desorption of the half-addition intermediates functioning as the key points. In addition, it is concluded that the catalyst prepared in a lower sulfiding atmosphere was more capable of adsorption than the other one.
基金This work was supported by the National Natural Science Foundation of China (No.51376185 and No.51106108), the National Basic Research Program of China (No.2012CB215304), the National High Technology Research and Development Program of China (No.2012AA101806), and the Natural Science Foundation of Guangdong Province (No.$2013010011612).
基金The financial support from the National Natural Science Foundation of China (20590361)the National Outstanding Young Scientists Foundation of China (20625620)
文摘A series of iron-based Fischer-Tropsch synthesis (FTS) catalysts incorporated with Al2O3 binder were prepared by the combination of co-precipitation and spray drying technology. The catalyst samples were characterized by using N2 physical adsorption, temperature-programmed reduction/desorption (TPR/TPD) and MSssbauer effect spectroscopy (MES) methods. The characterization results indicated that the BET surface area increases with increasing Al2O3 content and passes through a maximum at the Al2O3/Fe ratio of 10/100 (weight basis). After the point, it decreases with further increase in Al2O3 content. The incorporation of Al2O3 binder was found to weaken the surface basicity and suppress the reduction and carburization of iron-based catalysts probably due to the strong K-Al2O3 and Fe-Al2O3 interactions. Furthermore, the H2 adsorption ability of the catalysts is enhanced with increasing Al2O3 content. The FTS performances of the catalysts were tested in a slurry-phase continuously stirred tank reactor (CSTR) under the reaction conditions of 260 ℃, 1.5 MPa, 1000 h^-1 and molar ratio of H2/CO 0.67 for 200 h. The results showed that the addition of small amounts of Al2O3 affects the activity of iron-based catalysts to a little extent. However, with further increase of Al2O3 content, the FTS activity and water gas shift reaction (WGS) activity are decreased severely. The addition of appropriate Al2O3 do not affect the product selectivity, but the catalysts incorporated with large amounts of Al2O3 have higher selectivity for light hydrocarbons and lower selectivity for heavy hydrocarbons.
基金supported by the Jiangxi Provincial Department of Education
文摘The nickel-based catalysts were prepared by the sol-gel method and used for the CH4 reforming with CO2. The effects of the sol-gel method on the specific surface area, catalytic activity, desorption, and reduction performances of catalysts were investigated with BET, TPR, and TPD. Compared with the catalyst prepared by the impregnation method, the results indicated that the catalysts prepared by the sol-gel method had larger specific surface area, showing higher catalytic activities and exhibiting perfect desorption and reduction performances. In addition, the modification effects of adding La were studied, and it was found that the 0.75NLBT catalyst constituted of 5wt.%Ni-0.75wt.%La was optimal.
基金supported by the National Basic Research Program of China (Project No. 2005CB221405)the National "863" Project of China (No.2006AA10Z425)
文摘A series of Ni/SBA-15 catalysts with 5wt% to 15wt% Ni content as well as a series of 12.5%Ni/Cu/SBA-15 catalysts with 1% to 10% copper content were prepared by the impregnation method. The catalytic performance for partial oxidation of methane was investigated in a continuous flow microreactor under atmospheric pressure. The textural and chemical properties of the catalysts were characterized by XRD, TEM, BET and Hz-TPR techniques. The results indicated that the catalysts modified with Cu promoter showed better performance than those without modification. For the 12.5%Ni/2.5%/Cu/SBA-15 catalyst, at 850 ℃ the conversion of CH4 reached 97.9% and the selectivity of CO and H2 reached 98.0% and 96.0%, respectively. In XRD patterns of the Ni/Cu/SBA-15 catalyst with 7.5 to 10% Cu contents there were CuO characteristic peaks beside NiO characteristic peaks. The mesoporous structure of SBA-15 was retained in all of the catalysts. TPR analysis of the catalysts revealed that a strong interaction between Ni, Cu promoter and SBA-15 support may be existed. This interaction enhanced significantly the redox properties of the catalysts resulting in the higher catalytic activity.
文摘Highly active and selective Ni-based catalysts for partial oxidation of methane (POM) to syngas (CO/H,) have been studied and developed. Spectroscopic characterization by XRD, XPS, EPR, etc. demonstrated that under the POM reaction conditions, the Ni-components of the catalysts investigated were reduced and enriched on the surface to form metallic Ni0-phase. A comparative study of the first series of transition-metals showed that only Ni and Co have a high POM activity and selectivity, whereas the others (including Mn, Fe, Cu, etc. ) give mainly complete combustion products, Co, and H2O. The results favor the following viewpoints: the PoM activity is related with the rapidly changeable valence transitionmetal sites, M0/M2+ (e. g. Ni0/Ni2+ ), on the surface of the functioning catalysts;the transition-metal sites in zero-valence state seem to be responsible for the activation and dehydrogenation of methane by homolytic splitting of its C-H bonds on these sites. and the nature of rapidly changeable valence of the active sties is requisite for activation and rapid conversion of dioxygen.
基金supported by the National Basic Research Program of China(Project No.2005CB221405)the National "863" Project of China (No.2006AA10Z425)the Beijing Natural Science Foundation (Project No: 8062023)
文摘A series of Ni/SBA-15 catalysts with Ni contents from 7.5 wt% to 15 wt% were prepared by impregnation method.The effect of O2 and H2O on the combined reforming of the simulated biogas to syngas was investigated in a continuous flow fixed-bed micro-reactor.The stability of the catalyst was tested at 800 ?C.The results indicated that 10wt%Ni/SBA-15 catalyst exhibited the highest catalytic activities for the combined reforming of the simulated biogas to syngas.Under the reaction conditions of the feed gas molar ratios CH4/CO2/O2/H2O = 2/1/0.6/0.6,GHSV = 24000 ml·gcat^-1·h^-1 and the reaction temperature T = 800 ℃,the conversions of CH4 and CO2 were 92.8% and 76.3%,respectively,and the yields of CO and H2 were 99.0% and 82.0%,respectively.The catalytic activities of the catalyst did not decrease obviously after 100 h reaction time on stream.
文摘Various Cu/ZnO/Al2O3 catalysts have been synthesized by different aluminum emulsions as aluminum sources and their pertormances tor methanol synthesis from syngas have been investigated. The influences of preparation methods of aluminum emulsions on physicochemical and catalytic properties of catalysts were studied by XRD, SEM, XPS,N2 adsorption-desorption techniques and methanol synthesis from syngas. The preparation methods of aluminum emulsions were found to influence the catalytic activity, CuO crystallite size, surface area and Cu0 surface area and reduction process. The results show that the catalyst CN using the aluminum source prepared by addition the ammonia into the aluminum nitrate (NP) exhibited the best catalytic performance for methanol synthesis from syngas.