Flotation separation of scheelite from calcite using luteolin as a novel depressant

This paper proposes luteolin(LUT)as a novel depressant for the flotation-based separation of scheelite and calcite in a sodium oleate(NaOL)system.The suitability of LUT as a calcite depressant is confirmed through micro-flotation testing.At pH=9,with LUT concentration of 50 mg·L^(-1) and NaOL concentration of 50 mg·L^(-1),scheelite recovery reaches 80.3%.Calcite,on the other hand,exhibits a recovery rate of 17.6%,indicating a significant difference in floatability between the two minerals.Subsequently,the surface modifica-tions of scheelite and calcite following LUT treatment are characterized using adsorption capacity testing,Zeta potential analysis,Fourier transform infrared spectroscopy(FT-IR),X-ray photoelectron spectroscopy(XPS),and atomic force microscopy(AFM).The study in-vestigates the selective depressant mechanism of LUT on calcite.Adsorption capacity testing and Zeta potential analysis demonstrate sub-stantial absorption of LUT on the surface of calcite,impeding the further adsorption of sodium oleate,while its impact on scheelite is min-imal.FT-IR and XPS analyses reveal the selective adsorption of LUT onto the surface of calcite,forming strong chemisorption bonds between the hydroxyl group and calcium ions present.AFM directly illustrates the distinct adsorption densities of LUT on the two miner-al types.Consequently,LUT can effectively serve as a depressant for calcite,enabling the successful separation of scheelite and calcite.

Flotation separation of brucite and calcite in dodecylamine system enhanced by regulator potassium dihydrogen phosphate

To achieve efficient flotation separation of brucite and calcite,flotation separation experiments were conducted on two minerals using dodecylamine(DDA)as the collector and potassium dihydrogen phosphate(PDP)as the regulator.The action mechanism of DDA and PDP was explored through contact angle measurement,zeta potential detection,solution chemistry calculation,FTIR analysis,and XPS detection.The flotation results showed that when DDA dosage was 35 mg/L and PDP dosage was 40 mg/L,the maximum floating difference between brucite and calcite was 79.81%,and the selectivity separation index was 6.46.The detection analysis showed that the main dissolved component HPO_(4)^(2−)of PDP is selectively strongly adsorbed on the Ca site on the surface of calcite,promoting the adsorption of the main dissolved component RNH_(3)^(+)of DDA on calcite surface,while brucite is basically not affected by PDP.Therefore,PDP is an effective regulator for the reverse flotation separation of brucite and calcite in DDA system.

Role of tannin pretreatment in flotation separation of magnesite and dolomite

Flotation separation of magnesite and its calcium-containing carbonate minerals is a difficult problem.Recently,new regulat-ors have been proposed for magnesite flotation decalcification,although traditional regulators such as tannin,water glass,sodium carbon-ate,and sodium hexametaphosphate are more widely used in industry.However,they are rarely used as the main regulators in research because they perform poorly in magnesite and dolomite single-mineral flotation tests.Inspired by the limonite presedimentation method and the addition of a regulator to magnesite slurry mixing,we used a tannin pretreatment method for separating magnesite and dolomite.Microflotation experiments confirmed that the tannin pretreatment method selectively and largely reduces the flotation recovery rate of dolomite without affecting the flotation recovery rate of magnesite.Moreover,the contact angles of the tannin-pretreated magnesite and dolomite increased and decreased,respectively,in the presence of NaOl.Zeta potential and Fourier transform infrared analyses showed that the tannin pretreatment method efficiently hinders NaOl adsorption on the dolomite surface but does not affect NaOl adsorption on the magnesite surface.X-ray photoelectron spectroscopy and density functional theory calculations confirmed that tannin interacts more strongly with dolomite than with magnesite.

A novel molybdenite depressant for efficient selective flotation separation of chalcopyrite and molybdenite

A novel small molecule depressant(M-DEP)was used to separate chalcopyrite and molybdenite via flotation.The results showed that M-DEP had an excellent selective depression on molybdenite,while had little effect on the flotation of chalcopyrite.The adsorption capacity of M-DEP on the surface of molybdenite was greater than that on chalcopyrite surface.The adsorption of M-DEP reduced the floatability of molybdenite and had less effect on the floatability of chalcopyrite,which was due to its different adsorption modes on the surface of the two minerals.Furthermore,the interaction between chalcopyrite and M-DEP was mainly chemical interaction,and almost all of the adsorbed M-DEP molecules were removed and replaced by sodium butyl xanthate(SBX).By contrast,hydrophobic interaction was the main way in which M-DEP was adsorbed on the molybdenite surface with little chemical interaction,which was less interfered by SBX addition.Therefore,M-DEP had a super selective depression on molybdenite.The study provided a novel depressant and approach for the deep separation of chalcopyrite and molybdenite via flotation.

A novel surfactant N-hydroxy-9,10-epoxy group-octadecanamide:Part II.Its synthesis and application in flotation separation of spodumene and albite

A novel hydroxamic acid,N-hydroxy-9,10-epoxy group-octadecanamide(N-OH-9,10-O-ODA),was synthesised by modifying the structure of oleic acid.The carboxyl group of oleic acid was converted into an N-hydroxy amide group,and an epoxy group was introduced into its structure.N-OH-9,10-O-ODA was used as a novel collector in the flotation separation of spodumene from one of its associated gangue minerals,specifically albite.N-OH-9,10-O-ODA exhibits remarkable selectivity,with a stronger affinity for collecting spodumene particles compared to albite particles.Zeta potential measurements and X-ray photoelectron spectroscopic analysis reveal that the adsorption quantity of N-OH-9,10-O-ODA on spodumene surface is comparable to that on albite surface.First-principles calculations demonstrate the diverse adsorption configurations of N-OH-9,10-O-ODA on surfaces of spodumene and albite,leading to its distinct collecting abilities for spodumene and albite particles.

Cooperative effect of sodium lauryl sulfate collector and sodium pyrophosphate depressant on the flotation separation of lead oxide minerals from hematite

As a cornerstone of the national economy,the iron and steel industry generates a significant amount of sintering dust containing both valuable lead resources and deleterious elements.Flotation is a promising technique for lead recovery from sintering dust,but efficient separation from Fe_(2)O_(3) is still challenging.This study investigated the cooperative effect of sodium lauryl sulfate(SLS,C_(12)H_(25)SO_(4)Na)and sodium pyrophosphate(SPP,Na_(4)P_(2)O_(7))on the selective flotation of lead oxide minerals(PbOHCl and PbSO_(4))from hematite(Fe_(2)O_(3)).Optimal flotation conditions were first identified,resulting in high recovery of lead oxide minerals while inhibiting Fe_(2)O_(3) flotation.Zeta potential measurements,Fourier transform infrared spectroscopy(FT-IR)analysis,adsorption capacity analysis,and X-ray photoelectron spectroscopy(XPS)studies offer insights into the adsorption behaviors of the reagents on mineral surfaces,revealing strong adsorption of SLS on PbOHCl and PbSO_(4) surfaces and remarkable adsorption of SPP on Fe_(2)O_(3).The proposed model of reagent adsorption on mineral surfaces illustrates the selective adsorption behavior,highlighting the pivotal role of reagent adsorption in the separation process.These findings contribute to the efficient and environmentally friendly utilization of iron ore sintering dust for lead recovery,paving the way for sustainable resource management in the iron and steel industry.

Advances in depressants for flotation separation of Cu–Fe sulfide minerals at low alkalinity:A critical review

The flotation separation of Cu–Fe sulfide minerals at low alkalinity can be achieved using selective depressants.In the flotation system of Cu–Fe sulfide minerals,depressants usually preferentially interact with the pyrite surface to render the mineral surface hydrophilic and hinder the adsorption of the collector.This review summarizes the advances in depressants for the flotation separation of Cu–Fe sulfide minerals at low alkalinity.These advances include use of inorganic depressants (oxidants and sulfur–oxygen compounds),natural polysaccharides (starch,dextrin,konjac glucomannan,and galactomannan),modified polymers (carboxymethyl cellulose,polyacrylamide,lignosulfonate,and tricarboxylate sodium starch),organic acids (polyglutamic acid,sodium humate,tannic acid,pyrogallic acid,salicylic acid,and lactic acid),sodium dimethyl dithiocarbamate,and diethylenetriamine.The potential application of specific inorganic and organic depressants in the flotation separation of Cu–Fe sulfide minerals at low alkalinity is reviewed.The advances in the use of organic depressants with respect to the flotation separation of Cu–Fe sulfide minerals are comprehensively detailed.Additionally,the depression performances and mechanisms of different types of organic depressants on mineral surfaces are summarized.Finally,several perspectives on depressants vis-à-vis flotation separation of Cu–Fe sulfide minerals at low alkalinity are proposed.

Effect of depressants on flotation separation of magnesite from dolomite and calcite

The flotation separation of magnesite from calcium-containing minerals has always been a difficult subject in minerals processing.This work studied the inhibition effects of carboxymethyl cellulose(CMC),sodium lignosulphonate,polyaspartic acid(PASP)and sodium silicate on flotation behaviors of magnesite,dolomite and calcite,providing guidance for the development of reagents in magnesite flotation.The micro-flotation results showed that among these four depressants,sodium silicate presented the strongest selectivity due to the highest recovery difference,and the flotation separation of magnesite from dolomite and calcite could be achieved by using sodium silicate as the depressant.Contact angle measurement indicated that the addition of sodium silicate caused the largest differences in surface wettability of the three minerals,which was in line with micro-flotation tests.Furthermore,zeta potential test,the Fourier transform infrared(FT-IR)spectroscopy and atomic force microscope(AFM)imaging were used to reveal the inhibition mechanism of sodium silicate.The results indicated that the dominated component SiO(OH)3
of sodium silicate could adsorb on minerals surfaces,and the adsorption of sodium silicate hardly affected the adsorption of NaOL on magnesite surface,but caused the reduction of NaOL adsorption on dolomite and calcite surfaces,thereby increasing the flotation selectivity.

Activation mechanism of ammonium oxalate with pyrite in the lime system and its response to flotation separation of pyrite from arsenopyrite

The activation properties of ammonium oxalate on the flotation of pyrite and arsenopyrite in the lime system were studied in this work.Single mineral flotation tests showed that the ammonium oxalate strongly activated pyrite in high alkalinity and high Ca^(2+)system,whereas arsenopyrite was almost unaffected.In mineral mixtures tests,the recovery difference between pyrite and arsenopyrite after adding ammonium oxalate is more than 85%.After ammonium oxalate and ethyl xanthate treatment,the hydrophobicity of pyrite increased significantly,and the contact angle increased from 66.62°to 75.15°and then to 81.21°.After ammonium oxalate treatment,the amount of ethyl xanthate adsorption on the pyrite surface significantly increased and was much greater than that on the arsenopyrite surface.Zeta potential measurements showed that after activation by ammonium oxalate,there was a shift in the zeta potential of pyrite to more negative values by adding xanthate.X-ray photoelectron spectroscopy test showed that after ammonium oxalate treatment,the O 1s content on the surface of pyrite decreased from 44.03%to 26.18%,and the S 2p content increased from 14.01%to 27.26%,which confirmed that the ammonium oxalatetreated pyrite surface was more hydrophobic than the untreated surface.Therefore,ammonium oxalate may be used as a selective activator of pyrite in the lime system,which achieves an efficient flotation separation of S-As sulfide ores under high alkalinity and high Ca2+concentration conditions.

Boron separation by adsorption and flotation with Mg-Al-LDHs and SDBS from aqueous solution

Layered double hydroxides(LDHs)have been shown to be effective adsorbents for boron.However,solid-liquid separation is still a problem when separating boron from industrial radioactive waste liquid.In this research,three types of Mg-Al-LDHs including Mg-Al-LDH(NO_(3)^(-)),Mg-Al-LDH(Cl^(-))and Mg-Al-LDH(SO_(4)^(2-))were applied to adsorb boron,and moreover sodium dodecylbenzenesulfonate(SDBS)was used to float the LDH particles from aqueous solution after boron adsorption.The results showed that 60 min was sufficient for the equilibrium adsorption of the three LDHs.The boron adsorption capacity of three LDHs was determined as follows:Mg-Al-LDH(NO_(3)^(-))>Mg-Al-LDH(Cl^(-))>Mg-Al-LDH(SO_(4)^(2-)),and was 2.0,0.98 and 0.2 mmol·g^(-1),each ranging from 0 to 80 mmol·L^(-1)with the initial boron concentration.The efficiency of boron removal by Mg-Al-LDH(NO_(3)^(-))and SDBS can reach up to 89.7%.Furthermore,the boron flotation mechanism of SDBS and LDHs has been studied,since SDBS as a flotation agent can react with LDHs and penetrate into the interlayer of LDHs in addition to electrostatic attraction.Therefore,LDHs in solution can be floated onto the foam layer to be separated from the solution,and the clarified solution was obtained.The method is simple and promising for boron removal from aqueous solution.

Depression effect of pseudo glycolythiourea acid in flotation separation of copper-molybdenum

Pseudo glycolythiourea acid（PGA） was synthesized and used as depressant for flotation separation of Cu and Mo.The results indicate that a low amount of PGA has strong depression effect on chalcopyrite.Mo grade of 26.17% and recovery of 89.83% were achieved with rougher and scavenger one time and cleaners twice,while the recovery of Mo was deceased by 2% when Na2S was used as depressant.Measurement on adsorption of PGA on the mineral surface indicates that PGA and xanthate were adsorbed on mineral surface by competition,and PGA was adsorbed on chalcopyrite surface much stronger than on molybdenite surface.FTIR results indicate a chemical absorption process for PGA on chalcopyrite surface and a physical adsorption process on molybdenite surface.The frontier orbital calculation shows that the S atom is an active center,and the depression of PGA can be explained with the Fermi level of energy based on the electrochemical mechanism.

Flotation separation of andalusite from quartz using sodium petroleum sulfonate as collector

The floatability of andalusite and quartz was studied using sodium petroleum sulfonate as collector, being successfully applied in the real ore separation. The collecting performance on minerals was interpreted by means of zeta potential measurement and infrared spectroscopic analysis. The single mineral experiments showed that andalusite got good floatability in acidic pH region while quartz exhibited very poor floatability in the whole pH range. At pH 3, the presence of Fe3+ obviously activated quartz, causing the identical flotation behavior of the two minerals, and calcium lignosulphonate exhibited good selective inhibition to quartz. The real ore test results showed that andalusite concentrate with 53.46% Al2O3 and quartz concentrate with 92.74% SiO2 were obtained. The zeta potential and infrared spectroscopic analysis results indicated that chemical adsorption occurred between sodium petroleum sulfonate and andalusite.

Ferric ion-triggered surface oxidation of galena for efficient chalcopyrite-galena separation

The efficient separation of chalcopyrite(CuFeS2)and galena(PbS)is essential for optimal resource utilization.However,find-ing a selective depressant that is environmentally friendly and cost effective remains a challenge.Through various techniques,such as mi-croflotation tests,Fourier transform infrared spectroscopy,scanning electron microscopy(SEM)observation,X-ray photoelectron spec-troscopy(XPS),and Raman spectroscopy measurements,this study explored the use of ferric ions(Fe^(3+))as a selective depressant for ga-lena.The results of flotation tests revealed the impressive selective inhibition capabilities of Fe^(3+)when used alone.Surface analysis showed that Fe^(3+)significantly reduced the adsorption of isopropyl ethyl thionocarbamate(IPETC)on the galena surface while having a minimal impact on chalcopyrite.Further analysis using SEM,XPS,and Raman spectra revealed that Fe^(3+)can oxidize lead sulfide to form compact lead sulfate nanoparticles on the galena surface,effectively depressing IPETC adsorption and increasing surface hydrophilicity.These findings provide a promising solution for the efficient and environmentally responsible separation of chalcopyrite and galena.

Enhancing sustainability in phosphate ore processing:Performance of frying oil as alternative flotation collector for carbonate removal

Recycling waste frying oils for the synthesis of flotation reagents presents a promising avenue for sustainable waste management.Moreover,it offers a cost-effective solution for crafting a specialized collector designed to efficiently remove carbonates and enhance phosphate enrichment in froth flotation processes.This study focuses on the synthesis of an anionic collector using the saponification reaction of a frying oil sample,subsequently applied to the flotation of calcite and dolomite.To elucidate the adsorption mechanisms of the frying oil collector(FrOC)and sodium oleate,a reference collector,on fluorapatite,calcite,dolomite,and quartz surfaces,comprehensive experiments were conducted,including zeta potential measurements and Fourier transform infrared spectroscopy.Results revealed diverse adsorption affinities of the molecules towards these minerals.To assess the practical performance of the collector,flotation tests were conducted using a natural phosphate ore mixture,employing a BoxBehnken experimental design.Notably,under optimized conditions(pH 9,1000 g/t of FrOC,3.5 min of conditioning,and 6 min of flotation),FrOC exhibited excellent performance,with calcite and dolomite recoveries exceeding 80%,while apatite recovery in the concentrate fraction remained below 10%.This work exemplifies both circular economy practices and the distinctive approach to sustainable mineral processing.

Synergistic strengthening mechanism of Ca^(2+)-sodium silicate to selective separation of feldspar and quartz

Inhibitors are important for flotation separation of quartz and feldspar.In this study,a novel combined inhibitor was used to separate quartz and feldspar in near-neutral pulp.Selective inhibition of the combined inhibitor was assessed by micro-flotation experiments.And a series of detection methods were used to detect differences in the surface properties of feldspars and quartz after flotation reagents and put forward the synergistic strengthening mechanism.The outcomes were pointed out that pre-mixing combined inhibitors were more effective than the addition of Ca^(2+)and SS in sequence under the optimal proportion of 1:5.A concentrate from artificial mixed minerals that was characterized by a high quartz grade and a high recovery was acquired,and was found to be 90.70wt% and 83.70%,respectively.It was demonstrated that the combined inhibitor selectively prevented the action of the collector and feldspar from Fourier-transform infrared(FT-IR)and adsorption capacity tests.The results of X-ray photoelectron spectroscopy(XPS)indicated that Ca^(2+)directly interacts with the surface of quartz to increase the adsorption of collectors.In contrast,the chemistry property of Al on the feldspar surface was altered by combined inhibitor due to Na^(+)and Ca^(2+)taking the place of K^(+),resulting in the composite inhibitor forms a hydrophilic structure,which prevents the adsorption of the collector on the surface of feldspar by interacting with the Al active site.The combination of Ca^(2+)and SS synergically strengthens the difference of collecting property between quartz and feldspar by collector,thus achieving the effect of efficient separation.A new strategy for flotation to separate quartz from feldspar in near-neutral pulp was provided.

Effect of reverse flotation on magnetic separation concentrates

Reverse flotation studies on magnetite samples have revealed that the use of starch as a depressant of Fe-oxides has a hydrophilic effect on the surface of Fe-bearing silicates and significantly decreases Fe in the silica-rich stream when used in combination with an amine （Lilaflot D817M）. In this study, the effect of reverse flotation on the optimization of products obtained fi＇om magnetic separation was inves- tigated. Two different magnetic samples, zones 1 and 2, were milled to 〈75 btm and then subjected to low intensity magnetic separation （LIMS）. The LIMS test conducted on the 〈75 ~m shown an upgrade of 46.40wt% Fe, 28.40wt% SiO2 and 2.61wt% MnO for zone 1 and 47.60wt% Fe, 29.17wt% SiO2 and 0.50wt% MnO for zone 2. Further milling of the ore to 〈25 ~tm resulted in a higher magnetic-rich product after magnetic separation. Reverse flotation tests were conducted on the agitated magnetic concentrate feed, and the result shows a significant upgrade of Fe compared to that obtained from the non-agitated feed. Iron concentrations greater than 69%, and SiO2 concentrations less than 2% with overall magnetite recoveries greater than 67% and 71% were obtained for zones 1 and 2, respectively.

Selective depression mechanism of ferric chromium lignin sulfonate for chalcopyrite–galena flotation separation

Selective recovery of chalcopyrite–galena ore by flotation remains a challenging issue.The development of highly efficient,low-cost,and environmentally friendly depressants for this flotation is necessary because most of available reagents(e.g.,K_2Cr_2O_4)are expensive and adversely affect the environment.In this study,ferric chromium lignin sulfonate(FCLS),which is a waste-product from the paper and pulp industry,was introduced as a selective depressant for galena with butyl xanthate(BX)as a collector.Results show that the residue recovery of Pb in Cu concentrate was substantially reduced to 4.73%using FCLS compared with 10.71%using the common depressant K_2Cr_2O_4.The underlying mechanisms were revealed using zeta-potential measurements and X-ray photoelectron spectroscopy(XPS).Zeta-potential measurements revealed that FCLS was more efficiently absorbed onto galena than onto chalcopyrite.XPS measurements further suggested that FCLS enhanced the surface oxidation of galena but prevented that of chalcopyrite.Thus,FCLS could be a potential candidate as a depressant for chalcopyrite–galena flotation because of its low cost and its lack of detrimental effects on the environment.

New influence factor inducing difficulty in selective flotation separation of Cu–Zn mixed sulfide minerals

Selective flotation separation of Cu-Zn mixed sulfides has been proven to be difficult. Thus far, researchers have found no satis- factory way to separate Cu-Zn mixed sulfides by selective flotation, mainly because of the complex surface and interface interaction mecha- nisms in the flotation solution. Undesired activation occurs between copper ions and the sphalerite surfaces. In addition to recycled water and mineral dissolution, ancient fluids in the minerals are observed to be a new source of metal ions. In this study, significant amounts of ancient fluids were found to exist in Cu-Zn sulfide and gangue minerals, mostly as gas-liquid fluid inclusions. The concentration of copper ions re- leased from the ancient fluids reached 1.02 × 10-6 tool/L, whereas, in the cases of sphalerite and quartz, this concentration was 0.62 ×10-6 mol/L and 0.44 × 10-6 mol/L, respectively. As a result, the ancient fluid is a significant source of copper ions compared to mineral dissolution under the same experimental conditions, which promotes the unwanted activation of sphalerite. Therefore, the ancient fluid is considered to be a new factor that affects the selective flotation separation of Cu-Zn mixed sulfide ores.

A novel green depressant for flotation separation of scheelite from calcite

Polyaspartic acid(PASP)was used as a novel environmental-friendly depressant,and its inhibition effect on flotation performance of scheelite and calcite using sodium oleate(NaOL)as a collector was investigated by ways of flotation experiments,zeta potential measurement,contact angle measurement and infrared spectroscopic analysis(IR).The results show that PASP exhibits stronger inhibition capability and selectivity than acidified water glass,and the flotation separation of scheelite from calcite can be realized in the presence of 6 mg/L PASP and 20 mg/L NaOL at pH>6.In the presence of PASP,the zeta potential of calcite surface almost keeps unchanged after adding NaOL,and the contact angle decreases sharply.Therefore,it is indicated that PASP significantly decreases the adsorption of NaOL on calcite surface.By contrast,it has no distinct effect on the adsorption of NaOL on the scheelite surface,which is further confirmed by IR results.

Flotation separation of molybdenite and talc using tragacanth gum as depressant and potassium butyl xanthate as collector

Tragacanth gum(TG)was explored as a depressant to realize the flotation separation of molybdenite and talc.The flotation experiments indicated that when using potassium butyl xanthate(PBX)as a collector,molybdenite showed excellent floatability while talc was completely depressed by TG,thus realizing the flotation separation of the two minerals.X-ray photoelectron spectroscopy(XPS)analysis results showed that TG was adsorbed on molybdenite surface via chemisorption.The results of contact angle measurement,Fourier transform infrared(FTIR)spectroscopy,and time-of-flight secondary ion mass spectrometry(ToF-SIMS)indicated that the pre-adsorption of TG on molybdenite could not hinder the further chemisorption of PBX on molybdenite.Because PBX has no collecting ability on talc,the flotation separation of molybdenite and talc came true using PBX to collect molybdenite and TG to depress talc.