Polycrystalline CuGaSe2 thin films on Mo-coated soda-lime glass substrates have been synthesized by coevaporation process from Cu, Ga and Se sources. Structural and electrical properties of the as-grown CuGaSe2 films ...Polycrystalline CuGaSe2 thin films on Mo-coated soda-lime glass substrates have been synthesized by coevaporation process from Cu, Ga and Se sources. Structural and electrical properties of the as-grown CuGaSe2 films strongly depend on the film composition. Stoichiometric CuGaSe2 is fabricated, as indicated by x-ray diffraction spectroscope （XRD） and x-ray fluorescence （XRF）. A two-phase region is composed of CuGaSe2 and Cu2-xSe phases for Cu-rich films, and CuGaSe2 and CuGa3Se5 phases for Ga-rich films, respectively. Morphological properties are detected by scanning electron microscope （SEM） for various compositional films, the grain sizes of the CuGaSe2films decrease with the extent of deviation from stoichiometric composition. Raman spectroscopy of Cu-rich samples shows that there exist large Cu-Se particles on the film surface. The results from Hall effect measurements for typical samples indicate that CuGaSe2 films are always of p-type semiconductor from Cu-rich to Ga-rich. Stoichiometric CuGaSe2 films exhibit relatively large mobility than any other compositional films. Finally, polycrystalline CuGaSe2 thin film solar cell with a best conversion efficiency of 6.02% has been achieved under the standard air mass （AM）1.5 spectrum for 100mW/cm^2 at room temperature （aperture area, 0.24cm^2）. The open circuit voltage of the CuGaSe2 solar cells is close to770 mV.展开更多
We elucidate the importance of a capping layer on the structural evolution and phase change properties of carbondoped Ge2 Sb2 Te5（C-GST） films during heating in air. Both the C-GST films without and with a thin SiO2...We elucidate the importance of a capping layer on the structural evolution and phase change properties of carbondoped Ge2 Sb2 Te5（C-GST） films during heating in air. Both the C-GST films without and with a thin SiO2 capping layer（C-GST and C-GST/SiO2） are deposited for comparison. Large differences are observed between C-GST and C-GST/SiO2 films in resistance-temperature, x-ray diffraction, x-ray photoelectron spectroscopy,Raman spectra, data retention capability and optical band gap measurements. In the C-GST film, resistancetemperature measurement reveals an unusual smooth decrease in resistance above 110℃ during heating. Xray diffraction result has excluded the possibility of phase change in the C-GST film below 170℃. The x-ray photoelectron spectroscopy experimental result reveals the evolution of Te chemical valence because of the carbon oxidation during heating. Raman spectra further demonstrate that phase changes from an amorphous state to the hexagonal state occur directly during heating in the C-GST film. The quite smooth decrease in resistance is believed to be related with the formation of Te-rich GeTe4-n Gen（n = 0, 1） units above 110℃ in the C-GST film. The oxidation of carbon is harmful to the C-GST phase change properties.展开更多
The amorphous Ge2Sb2Te5 film with stoichiometric compositions was deposited by co-sputtering of separate Ge, Sb, and Te targets on SiO2/Si (100) wafer in ultrahigh vacuum magnetron sputtering apparatus. The crystalliz...The amorphous Ge2Sb2Te5 film with stoichiometric compositions was deposited by co-sputtering of separate Ge, Sb, and Te targets on SiO2/Si (100) wafer in ultrahigh vacuum magnetron sputtering apparatus. The crystallization behavior of amorphous Ge2Sb2Te5 film was investigated by X-ray diffraction (XRD), atomic force microscopy (AFM) and differential scanning calorimetry (DSC). With an increase of annealing temperature, the amorphous Ge2Sb2Te5 film undergoes a two-step crystallization process that it first crystallizes in face-centered-cubic (fcc) crystal structure and finally fcc structure changes to hexagonal (hex) structure. Activation energy values of 3.636±0.137 and 1.579±0.005 eV correspond to the crystallization and structural transformation processes, respectively. From annealing temperature dependence of the film resistivity, it is determined that the first steep decrease of the resistivity corresponds to crystallization while the second one is primarily caused by structural transformation from 'fcc' to 'hex' and growth of the crystal grains. Current-voltage (Ⅰ-Ⅴ) characteristics of the device with 40 nm-thick Ge2Sb2Te5 film show that the Ge2Sb2Te5 film with nanometer order thickness is still applicable for memory medium of nonvolatile phase change memory.展开更多
With the pulsed laser deposition （PLD） method, amorphous 80GeS2-15Ga2S3-5CdS chalcogenide film was deposited on glassy substrate. Obvious second harmonic generation （SHG） was observed in the ultraviolet （UV）-pol...With the pulsed laser deposition （PLD） method, amorphous 80GeS2-15Ga2S3-5CdS chalcogenide film was deposited on glassy substrate. Obvious second harmonic generation （SHG） was observed in the ultraviolet （UV）-polarized film and the SHG intensity increased with the increase in single pulse energy and irradiation time. Through Raman spectra and transmission spectra, the mechanism of SHG was studied. The experimental results demonstrated that effective electron traps and hole traps were generated in the UV- polarized film. The energy of electrons and holes was using up due to the collision with other particles and crystal fields during their movement and finally they were captured by the traps and fixed, which made the electric charge distribution nonuniform in the film and destroyed the spatial isotropy. In the meantime, the center of positive and negative charges separated and a built-in electric field was formed which generated the optical second-order nonlinearity of the film.展开更多
We report the experimental phenomenon of large resistance change in plasma oxidized TiOx/TiNx film fabricated on W bottom-electrode-contact （W-BEC） array. The W-BEC in diameter 26Ohm is fabricated by a 0.18μm CMOS ...We report the experimental phenomenon of large resistance change in plasma oxidized TiOx/TiNx film fabricated on W bottom-electrode-contact （W-BEC） array. The W-BEC in diameter 26Ohm is fabricated by a 0.18μm CMOS technology, and the TiOx/TiNx cell array is formed by rf magnetron sputtering and reactive ion etching. In current-voltage （I- V） measurement for current-sweeping mode, large snap-back of voltage is observed, which indicates that the sample changes from high-resistance state （HRS） to low-resistance state （LRS）. In the I-V measurement for voltage-sweeping mode, large current collapse is observed, which indicates that the sample changes from LRS to HRS. The current difference between HRS and LRS is about two orders. The threshold current and voltage for the resistance change is about 5.0- 10^-5 A and 2.5 V, respectively. The pulse voltage can also change the resistance and the pulse time is as shorter as 30 ns for the resistance change. These properties of TiOx/TiNx film are comparable to that of conventional phase-change material, which makes it possible for RRAM application.展开更多
The multiple-state storage capability of phase change memory （PCM） is confirmed by using stacked chalcogenide films as the storage medium. The current-voltage characteristics and the resistance-current characteristi...The multiple-state storage capability of phase change memory （PCM） is confirmed by using stacked chalcogenide films as the storage medium. The current-voltage characteristics and the resistance-current characteristics of the PCM clearly indicate that four states can be stored in this stacked film structure. Qualitative analysis indicates that the multiple-state storage capability of this stacked film structure is due to successive crystallizations in different Si-Sb-Te layers triggered by different amplitude currents.展开更多
Phase change memory （PCM） cell array is fabricated by a standard complementary metal-oxide-semiconductor process and the subsequent special fabrication technique. A chalcogenide Ge2Sb2Te5 film in thickness 50hm depo...Phase change memory （PCM） cell array is fabricated by a standard complementary metal-oxide-semiconductor process and the subsequent special fabrication technique. A chalcogenide Ge2Sb2Te5 film in thickness 50hm deposited by rf magnetron sputtering is used as storage medium for the PCM cell. Large snap-back effect is observed in current-voltage characteristics, indicating the phase transition from an amorphous state （higher resistance state） to the crystalline state （lower resistance state）. The resistance of amorphous state is two orders of magnitude larger than that of the crystalline state from the resistance measurement, and the threshold current needed for phase transition of our fabricated PCM cell array is very low （only several μA）. An x-ray total dose radiation test is carried out on the PCM cell array and the results show that this kind of PCM cell has excellent total dose radiation tolerance with total dose up to 2 ×10^6 rad（Si）, which makes it attractive for space-based applications.展开更多
A Ge2Sb2Te5 based phase change memory device cell integrated with metal-oxide semiconductor field effect transistor （MOSFET） is fabricated using standard 0.18 #m complementary metM-oxide semiconductor process techno...A Ge2Sb2Te5 based phase change memory device cell integrated with metal-oxide semiconductor field effect transistor （MOSFET） is fabricated using standard 0.18 #m complementary metM-oxide semiconductor process technology. It shows steady switching characteristics in the dc current-voltage measurement. The phase changing phenomenon from crystalline state to amorphous state with a voltage pulse altitude of 2.0 V and pulse width of 50ns is also obtained. These results show the feasibility of integrating phase change memory cell with MOSFET.展开更多
The blue shift of optical transmittance edges were observed in amorphous semiconductor Ge(S,Se)2 chal-cogenide films with light illumination. The shift in well-annealed films could be recovered by annealing the films ...The blue shift of optical transmittance edges were observed in amorphous semiconductor Ge(S,Se)2 chal-cogenide films with light illumination. The shift in well-annealed films could be recovered by annealing the films near the glass-transition temperature again. The photocrystalliza-tion was also observed in amorphous Ge(S,Se)2 films with light illumination by the transmitting electron microscope measurement. The photoinduced phenomina of the amorphous Ge(S,Se)2 films could be applied to designing some new kinds of optical storage materials.展开更多
基金Project supported by the National High Technology Joint Research Program of China (Grant No 2004AA513020)
文摘Polycrystalline CuGaSe2 thin films on Mo-coated soda-lime glass substrates have been synthesized by coevaporation process from Cu, Ga and Se sources. Structural and electrical properties of the as-grown CuGaSe2 films strongly depend on the film composition. Stoichiometric CuGaSe2 is fabricated, as indicated by x-ray diffraction spectroscope （XRD） and x-ray fluorescence （XRF）. A two-phase region is composed of CuGaSe2 and Cu2-xSe phases for Cu-rich films, and CuGaSe2 and CuGa3Se5 phases for Ga-rich films, respectively. Morphological properties are detected by scanning electron microscope （SEM） for various compositional films, the grain sizes of the CuGaSe2films decrease with the extent of deviation from stoichiometric composition. Raman spectroscopy of Cu-rich samples shows that there exist large Cu-Se particles on the film surface. The results from Hall effect measurements for typical samples indicate that CuGaSe2 films are always of p-type semiconductor from Cu-rich to Ga-rich. Stoichiometric CuGaSe2 films exhibit relatively large mobility than any other compositional films. Finally, polycrystalline CuGaSe2 thin film solar cell with a best conversion efficiency of 6.02% has been achieved under the standard air mass （AM）1.5 spectrum for 100mW/cm^2 at room temperature （aperture area, 0.24cm^2）. The open circuit voltage of the CuGaSe2 solar cells is close to770 mV.
基金Supported by the National Natural Science Foundation of China under Grant No 11704161the Natural Science Foundation of Jiangsu Province under Grant Nos BK20170309 and BK20151172the Changzhou Science and Technology Bureau under Grant Nos CJ20159049 and CJ20160028
文摘We elucidate the importance of a capping layer on the structural evolution and phase change properties of carbondoped Ge2 Sb2 Te5（C-GST） films during heating in air. Both the C-GST films without and with a thin SiO2 capping layer（C-GST and C-GST/SiO2） are deposited for comparison. Large differences are observed between C-GST and C-GST/SiO2 films in resistance-temperature, x-ray diffraction, x-ray photoelectron spectroscopy,Raman spectra, data retention capability and optical band gap measurements. In the C-GST film, resistancetemperature measurement reveals an unusual smooth decrease in resistance above 110℃ during heating. Xray diffraction result has excluded the possibility of phase change in the C-GST film below 170℃. The x-ray photoelectron spectroscopy experimental result reveals the evolution of Te chemical valence because of the carbon oxidation during heating. Raman spectra further demonstrate that phase changes from an amorphous state to the hexagonal state occur directly during heating in the C-GST film. The quite smooth decrease in resistance is believed to be related with the formation of Te-rich GeTe4-n Gen（n = 0, 1） units above 110℃ in the C-GST film. The oxidation of carbon is harmful to the C-GST phase change properties.
文摘The amorphous Ge2Sb2Te5 film with stoichiometric compositions was deposited by co-sputtering of separate Ge, Sb, and Te targets on SiO2/Si (100) wafer in ultrahigh vacuum magnetron sputtering apparatus. The crystallization behavior of amorphous Ge2Sb2Te5 film was investigated by X-ray diffraction (XRD), atomic force microscopy (AFM) and differential scanning calorimetry (DSC). With an increase of annealing temperature, the amorphous Ge2Sb2Te5 film undergoes a two-step crystallization process that it first crystallizes in face-centered-cubic (fcc) crystal structure and finally fcc structure changes to hexagonal (hex) structure. Activation energy values of 3.636±0.137 and 1.579±0.005 eV correspond to the crystallization and structural transformation processes, respectively. From annealing temperature dependence of the film resistivity, it is determined that the first steep decrease of the resistivity corresponds to crystallization while the second one is primarily caused by structural transformation from 'fcc' to 'hex' and growth of the crystal grains. Current-voltage (Ⅰ-Ⅴ) characteristics of the device with 40 nm-thick Ge2Sb2Te5 film show that the Ge2Sb2Te5 film with nanometer order thickness is still applicable for memory medium of nonvolatile phase change memory.
基金Funded by the National Natural Science Foundaition of China(Nos.51172169 and 61177084),NCET\(NCET-11-0687)the Fundamental Research Funds for the Central Universities(Wuhan University of Technology)
文摘With the pulsed laser deposition （PLD） method, amorphous 80GeS2-15Ga2S3-5CdS chalcogenide film was deposited on glassy substrate. Obvious second harmonic generation （SHG） was observed in the ultraviolet （UV）-polarized film and the SHG intensity increased with the increase in single pulse energy and irradiation time. Through Raman spectra and transmission spectra, the mechanism of SHG was studied. The experimental results demonstrated that effective electron traps and hole traps were generated in the UV- polarized film. The energy of electrons and holes was using up due to the collision with other particles and crystal fields during their movement and finally they were captured by the traps and fixed, which made the electric charge distribution nonuniform in the film and destroyed the spatial isotropy. In the meantime, the center of positive and negative charges separated and a built-in electric field was formed which generated the optical second-order nonlinearity of the film.
基金This work was financially supported bythe National Natural Science Foundation of China(50125205),the Programfor Changjiang Scholars andlnnovative Research Team(IRT0547),and the Opening Fund of Key Laboratory of Silicate Materials Science and Engineering(Wuhan University of Technology),Ministry of Education (SYSJJ2004-14).
基金Supported by the National Basic Research Program of China under Grant No 2006CB302700, the National High Technology Development Programme of China under Grant No 2006AA03Z360~ Chinese Academy of Sciences （Y2005027）, Science and Technology Council of Shanghai under Grant Nos AM0517, 05JC14076, 0552nm043, 06QA14060, 06XD14025, 0652nm003, and 06DZ22017, the China Postdoctoral Science Foundation, and the K. C. Wong Education Foundation （Hong Kong）.
文摘We report the experimental phenomenon of large resistance change in plasma oxidized TiOx/TiNx film fabricated on W bottom-electrode-contact （W-BEC） array. The W-BEC in diameter 26Ohm is fabricated by a 0.18μm CMOS technology, and the TiOx/TiNx cell array is formed by rf magnetron sputtering and reactive ion etching. In current-voltage （I- V） measurement for current-sweeping mode, large snap-back of voltage is observed, which indicates that the sample changes from high-resistance state （HRS） to low-resistance state （LRS）. In the I-V measurement for voltage-sweeping mode, large current collapse is observed, which indicates that the sample changes from LRS to HRS. The current difference between HRS and LRS is about two orders. The threshold current and voltage for the resistance change is about 5.0- 10^-5 A and 2.5 V, respectively. The pulse voltage can also change the resistance and the pulse time is as shorter as 30 ns for the resistance change. These properties of TiOx/TiNx film are comparable to that of conventional phase-change material, which makes it possible for RRAM application.
文摘The multiple-state storage capability of phase change memory （PCM） is confirmed by using stacked chalcogenide films as the storage medium. The current-voltage characteristics and the resistance-current characteristics of the PCM clearly indicate that four states can be stored in this stacked film structure. Qualitative analysis indicates that the multiple-state storage capability of this stacked film structure is due to successive crystallizations in different Si-Sb-Te layers triggered by different amplitude currents.
基金Supported by the Chinese Academy of Sciences （Y2005027）, the Science and Technology Council of Shanghai （AM0517, 0452nm012, 04DZ05612, 04ZR14154, 04JC14080, 05JC14076, AM0414, 05nm05043）, the China Postdoctoral Science Foundation, and the K. C. Wong Education Foundation （Hong Kong）.
文摘Phase change memory （PCM） cell array is fabricated by a standard complementary metal-oxide-semiconductor process and the subsequent special fabrication technique. A chalcogenide Ge2Sb2Te5 film in thickness 50hm deposited by rf magnetron sputtering is used as storage medium for the PCM cell. Large snap-back effect is observed in current-voltage characteristics, indicating the phase transition from an amorphous state （higher resistance state） to the crystalline state （lower resistance state）. The resistance of amorphous state is two orders of magnitude larger than that of the crystalline state from the resistance measurement, and the threshold current needed for phase transition of our fabricated PCM cell array is very low （only several μA）. An x-ray total dose radiation test is carried out on the PCM cell array and the results show that this kind of PCM cell has excellent total dose radiation tolerance with total dose up to 2 ×10^6 rad（Si）, which makes it attractive for space-based applications.
文摘A Ge2Sb2Te5 based phase change memory device cell integrated with metal-oxide semiconductor field effect transistor （MOSFET） is fabricated using standard 0.18 #m complementary metM-oxide semiconductor process technology. It shows steady switching characteristics in the dc current-voltage measurement. The phase changing phenomenon from crystalline state to amorphous state with a voltage pulse altitude of 2.0 V and pulse width of 50ns is also obtained. These results show the feasibility of integrating phase change memory cell with MOSFET.
文摘The blue shift of optical transmittance edges were observed in amorphous semiconductor Ge(S,Se)2 chal-cogenide films with light illumination. The shift in well-annealed films could be recovered by annealing the films near the glass-transition temperature again. The photocrystalliza-tion was also observed in amorphous Ge(S,Se)2 films with light illumination by the transmitting electron microscope measurement. The photoinduced phenomina of the amorphous Ge(S,Se)2 films could be applied to designing some new kinds of optical storage materials.
