Improved formation density measurement using controllable D-D neutron source and its lithological correction for porosity prediction

Controllable D-D neutron sources have a long service life,low cost,and non-radioactivity.There are favorable prospects for its application in geophysical well logging,since traditional chemical radioactive sources used for well logging pose potential threats to the safety of the human body and environment.This paper presents an improved method to measure formation density that employs a D-D neutron source.In addition,the lithological effect on the measured density was removed to better estimate the formation porosity.First,we investigated the spatial distribution of capture gamma rays through Monte Carlo simulations as well as the relationship between the ratio of capture gamma ray counts and formation density to establish theoretical support for the design of density logging tools and their corresponding data processing methods.Second,we obtained the far to near detector counts of captured gamma rays for an optimized tool structure and then established its correlation with the density and porosity of three typical formations with pure quartz,calcite,and dolomite minerals.Third,we determined the values for correcting the densities of sandstone and dolomite with the same porosity using limestone data as the reference and established the equations for calculating the correction values,which lays a solid foundation for accurately calculating formation porosity.We observed that the capture gamma ray counts first increased then decreased and varied in different formations;this was especially observed in high-porosity formations.Under the same lithologic conditions(rock matrix),as the porosity increases,the peak value of gamma ray counts moves toward the neutron source.At different detector-source distances,the ratio of the capture gamma ray counts was well correlated with the formation density.An equation of the formation density conversion was established based on the ratio of capture gamma ray counts at the detector-source distances of 30 cm and 65 cm,and the calculated values were consistent with the true values.After correction,the formation density was highly consistent with the true value of the limestone density,and the mean absolute error was 0.013 g/cm3.The calculated porosity values were very close to the true values,and the mean relative error was 2.33%,highlighting the accuracy of the proposed method.These findings provide a new method for developing D-D neutron source logging tools and their well-log data processing methods.

10B-doped MCP detector developed for neutron resonance imaging at Back-n white neutron source

Neutron resonance imaging(NRI)has recently emerged as an appealing technique for neutron radiography.Its complexity surpasses that of conventional transmission imaging,as it requires a high demand for both a neutron source and detector.Consequently,the progression of NRI technology has been sluggish since its inception in the 1980s,particularly considering the limited studies analyzing the neutron energy range above keV.The white neutron source(Back-n)at the China Spallation Neutron Source(CSNS)provides favorable beam conditions for the development of the NRI technique over a wide neutron energy range from eV to MeV.Neutron-sensitive microchannel plates(MCP)have emerged as a cutting-edge tool in the field of neutron detection owing to their high temporal and spatial resolutions,high detection efficiency,and low noise.In this study,we report the development of a 10B-doped MCP detector,along with its associated electronics,data processing system,and NRI experiments at the Back-n.Individual heavy elements such as gold,silver,tungsten,and indium can be easily identified in the transmission images by their characteristic resonance peaks in the 1–100 eV energy range;the more difficult medium-weight elements such as iron,copper,and aluminum with resonance peaks in the 1–100 keV energy range can also be identified.In particular,results in the neutron energy range of dozens of keV(Aluminum)are reported here for the first time.

Study on the optimal incident proton energy of ^(7)Li(p,n)^(7)Be neutron source for boron neutron capture therapy

Boron neutron capture therapy(BNCT)is recognized as a precise binary targeted radiotherapy technique that effectively eliminates tumors through the^(10)B(n,α)^(7)Li nuclear reaction.Among various neutron sources,accelerator-based sources have emerged as particularly promising for BNCT applications.The^(7)Li(p,n)^(7)Be reaction is highly regarded as a potential neutron source for BNCT,owing to its low threshold energy for the reaction,significant neutron yield,appropriate average neutron energy,and additional benefits.This study utilized Monte Carlo simulations to model the physical interactions within a lithium target subjected to proton bombardment,including neutron moderation by an MgF_(2)moderator and subsequent BNCT dose analysis using a Snyder head phantom.The study focused on calculating the yields of epithermal neutrons for various incident proton energies,finding an optimal energy at 2.7 MeV.Furthermore,the Snyder head phantom was employed in dose simulations to validate the effectiveness of this specific incident energy when utilizing a^(7)Li(p,n)^(7)Be neutron source for BNCT purposes.

Resolution analysis of thermal neutron radiography based on accelerator-driven compact neutron source

Owing to the immobility of traditional reactors and spallation neutron sources,the demand for compact thermal neutron radiography(CTNR)based on accelerator neutron sources has rapidly increased in industrial applications.Recently,thermal neutron radiography experiments based on a D-T neutron generator performed by Hefei Institutes of Physical Science indicated a significant resolution deviation between the experimental results and the values calculated using the traditional resolution model.The experimental result was up to 23%lower than the calculated result,which hinders the achievement of the design goal of a compact neutron radiography system.A GEANT4 Monte Carlo code was developed to simulate the CTNR process,aiming to identify the key factors leading to resolution deviation.The effects of a low collimation ratio and high-energy neutrons were analyzed based on the neutron beam environment of the CTNR system.The results showed that the deviation was primarily caused by geometric distortion at low collimation ratios and radiation noise induced by highenergy neutrons.Additionally,the theoretical model was modified by considering the imaging position and radiation noise factors.The modified theoretical model was in good agreement with the experimental results,and the maximum deviation was reduced to 4.22%.This can be useful for the high-precision design of CTNR systems.

Neutronics analysis of a subcritical blanket system driven by a gas dynamic trap-based fusion neutron source for ^(99)Mo production

Gamma-emitting radionuclide ^(99m)Tc is globally used for the diagnosis of various pathological conditions owing to its ideal single-photon emission computed tomography (SPECT) characteristics.However,the short half-life of ^(99m)Tc (T_(1/2)=6 h)makes it difficult to store or transport.Thus,the production of ^(99m)Tc is tied to its parent radionuclide ^(99)Mo (T_(1/2)=66 h).The major production paths are based on accelerators and research reactors.The reactor process presents the potential for nuclear proliferation owing to its use of highly enriched uranium (HEU).Accelerator-based methods tend to use deuterium–tritium(D–T) neutron sources but are hindered by the high cost of tritium and its challenging operation.In this study,a new ^(99)Mo production design was developed based on a deuterium–deuterium (D–D) gas dynamic trap fusion neutron source (GDT-FNS) and a subcritical blanket system (SBS) assembly with a low-enriched uranium (LEU) solution.GDT-FNS can provide a relatively high-neutron intensity,which is one of the advantages of ^(99)Mo production.We provide a Monte Carlo-based neutronics analysis covering the calculation of the subcritical multiplication factor (k_(s)) of the SBS,optimization design for the reflector,shielding layer,and ^(99)Mo production capacity.Other calculations,including the neutron flux and nuclear heating distributions,are also provided for an overall evaluation of the production system.The results demonstrated that the SBS meets the nuclear critical safety design requirement (k_(s)<0.97) and maintained a high ^(99)Mo production capacity.The proposed system can generate approximately 157 Ci ^(99)Mo for a stable 24 h operation with a neutron intensity of 1×10^(14) n/s,which can meet 50%of China’s demand in 2025.

Analysis of displacement damage effects on the charge-coupled device induced by neutrons at Back-n in the China Spallation Neutron Source

Displacement damage effects on the charge-coupled device(CCD)induced by neutrons at the back-streaming white neutron source(Back-n)in the China Spallation Neutron Source(CSNS)are analyzed according to an online irradiation experiment.The hot pixels,random telegraph signal(RTS),mean dark signal,dark current and dark signal non-uniformity(DSNU)induced by Back-n are presented.The dark current is calculated according to the mean dark signal at various integration times.The single-particle displacement damage and transient response are also observed based on the online measurement data.The trends of hot pixels,mean dark signal,DSNU and RTS degradation are related to the integration time and irradiation fluence.The mean dark signal,dark current and DSNU2 are nearly linear with neutron irradiation fluence when nearly all the pixels do not reach saturation.In addition,the mechanisms of the displacement damage effects on the CCD are demonstrated by combining the experimental results and technology computer-aided design(TCAD)simulation.Radiation-induced traps in the space charge region of the CCD will act as generation/recombination centers of electron-hole pairs,leading to an increase in the dark signal.

Silicon photomultiplier based scintillator thermal neutron detector for China Spallation Neutron Source(CSNS)

The energy-resolved neutron imaging spectrometer(ERNI)will be installed in 2022 according to the spectrometer construction plan of the China Spallation Neutron Source(CSNS).The instrument requires neutron detectors with the coverage area of approximately 4 m^(2)in 5°-170°neutron diffraction angle.The neutron detection efficiency needs to be better than 40%at 1 A neutron wavelength.The spatial resolution should be better than 3 mm×50 mm in the horizontal and vertical directions respectively.We develop a one-dimensional scintillator neutron detector which is composed of the^(6)Li F/Zn S(Ag)scintillation screens,the wavelength-shifting fiber(WLSF)array,the silicon photomultipliers(Si PMs),and the self-designed application-specific integrated circuit(ASIC)readout electronics.The pixel size of the detector is designed as 3 mm×50 mm,and the neutron-sensitive area is 50 mm×200 mm.The performance of the detector prototype is measured using neutron beam 20#of the CSNS.The maximum counting rate of 247 k Hz,and the detection efficiency of63%at 1.59 A are obtained.The test results show that the performance of the detector fulfills the physical requirements of the ERNI under construction at the CSNS.

Measurement of the relative neutron sensitivity curve of a LaBr_(3)(Ce)scintillator based on the CSNS Back-n white neutron source

A scintillator detector consisting of a LaBr_(3)(Ce)(0.5%)scintillator,a photomultiplier tube(PMT),and an oscilloscope were used to study the neutron sensitivities of the LaBr_(3)(Ce)scintillator at the China Spallation Neutron Source(CSNS)Back-n white neutron source in the double-bunch and single-bunch operation modes,respectively.Under the two operational modes,the relative neutron sensitivity curves of the LaBr_(3)(Ce)scintillator in the energy regions of 1–20 MeV and 0.5–20 MeV were obtained for the first time.In the energy range of 1–20 MeV,the two curves were nearly identical.However the relative neutron sensitivity uncertainties of the double-bunch experiment were higher than those of the single-bunch experiment.The above results indicated that the single-bunch experiment's neutron sensitivity curve has a lower minimum measurable energy than the double-bunch experiment.Above the minimum measurable energy of the double-bunch experiment,there is little difference between the measured relative neutron sensitivity curves of the single-bunch and double-bunch experiments of the LaBr_(3)(Ce)scintillator and those of other scintillators with a similar neutron response signal intensity.

Effect of Fusion Neutron Source Numerical Models on Neutron Wall Loading in a D-D Tokamak Device

Effect of various spatial and energy distributions of fusion neutron sourceon the calculation of neutron wall loading of Tokamak D-D fusion device has been investigated bymeans of the 3-D Monte Carlo code MCNP. A realistic Monte Carlo source model was developed based onthe accurate representation of the spatial distribution and energy spectrum of fusion neutrons tosolve the complicated problem of tokamak fusion neutron source modelling. The results show thatthose simplified source models will introduce significant uncertainties. For accurate estimation ofthe key nuclear responses of the tokamak design and analyses, the use of the realistic source isrecommended. In addition, the accumulation of tritium produced during D-D plasma operation should becarefully considered.

Back-n white neutron source at CSNS and its applications

Back-streaming neutrons from the spallation target of the China Spallation Neutron Source(CSNS)that emit through the incoming proton channel were exploited to build a white neutron beam facility(the so-called Back-n white neutron source),which was completed in March 2018.The Back-n neutron beam is very intense,at approximately 29107 n/cm2/s at 55 m from the target,and has a nominal proton beam with a power of 100 kW in the CSNS-I phase and a kinetic energy of 1.6 GeV and a thick tungsten target in multiple slices with modest moderation from the cooling water through the slices.In addition,the excellent energy spectrum spanning from 0.5 eV to 200 MeV,and a good time resolution related tothe time-of-flight measurements make it a typical white neutron source for nuclear data measurements;its overall performance is among that of the best white neutron sources in the world.Equipped with advanced spectrometers,detectors,and application utilities,the Back-n facility can serve wide applications,with a focus on neutron-induced cross-sectional measurements.This article presents an overview of the neutron beam characteristics,the experimental setups,and the ongoing applications at Backn.

基于D-D中子源开展^(238)U样品屏蔽积分实验研究

利用中国原子能科学研究院的中子学屏蔽积分实验装置,通过飞行时间法分别测量了D-D中子源与不同尺寸^(238)U样品作用后在60°和120°的泄漏中子谱,样品表面积为30 cm×30 cm的板状样品,厚度分别为3、6和9 cm。利用蒙特卡罗程序对泄漏中子谱进行了模拟计算,其中^(238)U数据分别采用CENDL-3.2库、ENDF/B-Ⅷ.0库、JENDL-5.0库和JEFF-3.3库中的数据。通过对模拟结果与实验结果的比较,重点分析了CENDL-3.2库中^(238)U数据存在的不足和需要改进之处,结果表明:在裂变反应能区内,CENDL-3.2库计算结果与实验结果符合较好,但在弹性散射能区60°和120°均有较大的高估,尤其是120°,而在裂变反应和分立能级非弹性散射的混合能区1.5~2.5 MeV又有明显低估。

Benchmark experiment on slab^(238)U with D-T neutrons for validation of evaluated nuclear data

A benchmark experiment on^(238)U slab samples was conducted using a deuterium-tritium neutron source at the China Institute of Atomic Energy.The leakage neutron spectra within energy levels of 0.8-16 MeV at 60°and 120°were measured using the time-of-flight method.The samples were prepared as rectangular slabs with a 30 cm square base and thicknesses of 3,6,and 9 cm.The leakage neutron spectra were also calculated using the MCNP-4C program based on the latest evaluated files of^(238)U evaluated neutron data from CENDL-3.2,ENDF/B-Ⅷ.0,JENDL-5.0,and JEFF-3.3.Based on the comparison,the deficiencies and improvements in^(238)U evaluated nuclear data were analyzed.The results showed the following.(1)The calculated results for CENDL-3.2 significantly overestimated the measurements in the energy interval of elastic scattering at 60°and 120°.(2)The calculated results of CENDL-3.2 overestimated the measurements in the energy interval of inelastic scattering at 120°.(3)The calculated results for CENDL-3.2 significantly overestimated the measurements in the 3-8.5 MeV energy interval at 60°and 120°.(4)The calculated results with JENDL-5.0 were generally consistent with the measurement results.

紧凑型各向异性D-D中子源源强测量实验研究

采用Bonner多球谱仪、3He正比计数器和238 U裂变电离室3种不同探测方法,分别同时从束流方向0°,90°,180°3个角度对紧凑型各向异性D-D中子源进行源强测量,通过蒙特卡罗方法修正实验室对测量结果的影响,得到3组源强测量结果。结果表明:3种探测方法的测量结果分别为8.88×10^(9),8.13×10^(9),8.82×10^(9)s^(-1)。3组中子源强测量结果的相对偏差在10%以内,与理论值偏差较小。与其他两种方法相比,采用238 U裂变电离室探测器的源强测量结果总相对偏差最小,证明了采用不同探测方法从多个角度同时测量各向异性中子源源强的可行性。研究可为相似实验条件下同类型中子源的特征参数测量提供研究思路。

Neutronics analysis of a stacked structure for a subcritical system with LEU solution driven by a D-T neutron source for~(99)Mo production

The utilization of neutrons markedly affects the medical isotope yield of a subcritical system driven by an external D-T neutron source.The general methods to improve the utilization of neutrons include moderating multiplying,and reflecting neutrons,which ignores the use of neutrons that backscatter to the source direction.In this study,a stacked structure was formed by assembling the multiplier and the low-enriched uranium solution to enable the full use of neutrons that backscatter to the source direction and further improve the utilization of neutrons.A model based on SuperMC was used to evaluate the neutronics and safety behavior of the subcritical system,such as the neutron effective multiplication factor,neutron energy spectrum,medical isotope yield,and heat deposition.Based on the calculation results,when the intensity of the neutron source was 59×10^(13)n/s,the optimized design with a stacked structure could increase the yield of ^(99)Mo to182 Ci/day,which is approximately 16% higher than that obtained with a single-layer structure.The inlet H_(2)O coolant velocity of 1.0 m/s and initial temperature of 20℃ were also found to be sufficient to prevent boiling of the fuel solution.

Simulation and optimization for a 30-MeV electron accelerator driven neutron source

A neutron source driven by electron accelerator is proposed in Shanghai Institute of Applied Physics (SINAP). The facility is planned for the study of nuclear data in Thorium-Uranium cycling system, and for material research. A detailed simulation of the neutron source is performed for the program to get the neutron generation maximum economically. Several parameters of the facility, which affect the neutron yield and the neutron escape from outer surface of the target, are analyzed respectively. Besides, the yielding neutron spectrum and the escaping neutron angular distribution are calculated and discussed.

Study on inherent neutron sources in MSR

The molten salt reactor(MSR) has received much recent attention. The presence of beryllium and the mixing of actinides with light nuclei in the fuel salt result in a relatively strong neutron source that can affect the surveillance at subcritical and transient characteristics during operation. In this study, we predict the inherent neutron sources based on a MSR model. The calculation shows that in the fresh core, the inherent neutron sources are mainly from alpha-induced neutrons. After power operation, the inherent neutron sources become remarkably stronger due to photoneutrons. Although being an insignificant part in the total neutron population during operation, the inherent neutron sources can be used as the installed neutron source after shutdown. If the MSR has continuously operated at full power(2 MWt) for 10 days,then there would be no need for the installed source within80 days after shutdown. After operating constantly for500 days, the installed neutron source can be eliminated within 2 years after shutdown.

A Fusion Neutron Source Driven Sub-Critical Nuclear Energy System: A Way for Early Application of Fusion Technology

This paper proposes a sub-critical nuclear energy system driven by fusion neutron source, FDS, which can be used to transmute long-lived radioactive wastes and to produce fissile nuclear fuel as a way for early application of fusion technology. The necessity and feasibility to develop that system in China are illustrated on the basis of prediction of the demand of energy source in the first half of the 21th century, the status of current fission energy supply and the progress in fusion technology in the world. The characteristics of fusion neutron driver and the potential for transmutation of long-lived nuclear wastes and breeding of fissile nuclear fuel in a blanket are analyzed. A scenario of development steps is proposed.

A tabletop, ultrashort pulse photoneutron source driven by electrons from laser wakefield acceleration

Relativistic electron beams driven by laser wakefield acceleration were utilized to produce ultrashort neutron sources.The experiment was carried out on the 38 fs,~0.5 J,800 nm Ti:Sapphire laser in the 10 TW UT 3 laser lab at University of Texas at Austin.The target gas was a high density pulsed gas jet composed of 90%He and 10%N 2.The laser pulse with a peak intensity of 1.5×10^(18) W/cm^(2) interacted with the target to create a cylindrical plasma channel of 60 mm radius(FWHM)and 1.5 mm length(FWHM).Electron beams of~80 pC with the Gaussian energy distribution centered at 37 MeV and a width of 30 MeV(FWHM)were produced via laser wakefield acceleration.Neutron fluences of~2.4×10^(6) per shot with hundreds of ps temporal length were generated through bremsstrahlung and subsequent photoneutron reactions in a 26.6 mm thick tungsten converter.Results were compared with those of simulations using EPOCH and GEANT4,showing agreement in electron spectrum,neutron fluence,neutron angular distribution and conversion rate.

Physics Analysis and Optimization Studies for a Fusion Neutron Source Based on a Gas Dynamic Trap

To further investigate the fusion neutron source based on a gas dynamic trap （GDT）, characteristics of the GDT were analyzed and physics analyses were made for a fusion neutron source based on the GDT concept. The prior design of a GDT-based fusion neutron source was optimized based on a refreshed understanding of GDT operation. A two-step progressive development route of a GDT-based fusion neutron source was suggested. Potential applications of GDT are discussed. Preliminary analyses show that a fusion neutron source based on the GDT concept is suitable for plasma-material interaction research, fusion material and subcomponent testing, and capable of driving a proof-of-principle fusion fission hybrid experimental facility.

基于D-D源的三探头中子孔隙度测井探测响应分析

随着油气勘探进程持续推进,低孔隙度储层越发受到关注,具备更高孔隙度灵敏度的D-D源中子测井存在良好应用前景,为了进一步探索其兼顾中子孔隙度测量灵敏度与化学源测量兼容性的可能性,提出一种基于D-D源的三探头中子孔隙度测井设计并开展分析。为探究D-D源中子孔隙度测量响应特征,利用蒙特卡罗方法,基于三探头测井仪器的基本构成,研究了探测器源距设计,并提出利用测量的近远热中子计数比、中远热中子计数比这2组比值分别表征地层孔隙度,同时对D-D源中子孔隙度测井的地层探测能力与地层测量响应进行了综合分析。研究表明:三探头D-D源中子孔隙度测井仪器探测深度稍浅、纵向分辨率较高;近远热中子计数比值响应表现出更高地层孔隙度灵敏度,低孔隙度地层情况下测得的孔隙度变化效果良好;中远热中子计数比值响应泥岩效应较强,虽无法与化学源测量结果兼容,但在纯岩性及含泥质地层与其较高程度接近。该文研究为D-D源中子孔隙度测井仪器测量应用提供了一定参考。