ANovel Non-Isolated Cubic DC-DC Converter with High Voltage Gain for Renewable Energy Power Generation System

In recent years,switched inductor(SL)technology,switched capacitor(SC)technology,and switched inductor-capacitor(SL-SC)technology have been widely applied to optimize and improve DC-DC boost converters,which can effectively enhance voltage gain and reduce device stress.To address the issue of low output voltage in current renewable energy power generation systems,this study proposes a novel non-isolated cubic high-gain DC-DC converter based on the traditional quadratic DC-DC boost converter by incorporating a SC and a SL-SC unit.Firstly,the proposed converter’s details are elaborated,including its topology structure,operating mode,voltage gain,device stress,and power loss.Subsequently,a comparative analysis is conducted on the voltage gain and device stress between the proposed converter and other high-gain converters.Then,a closed-loop simulation system is constructed to obtain simulation waveforms of various devices and explore the dynamic performance.Finally,an experimental prototype is built,experimental waveforms are obtained,and the experimental dynamic performance and conversion efficiency are analyzed.The theoretical analysis’s correctness is verified through simulation and experimental results.The proposed converter has advantages such as high voltage gain,low device stress,high conversion efficiency,simple control,and wide input voltage range,achieving a good balance between voltage gain,device stress,and power loss.The proposed converter is well-suited for renewable energy systems and holds theoretical significance and practical value in renewable energy applications.It provides an effective solution to the issue of low output voltage in renewable energy power generation systems.

Simple digital PWM and PSM controlled DC-DC boost converter for luminance-regulated WLED driver

This article presents a control strategy based on simple digital pulse-width modulation （DPWM） and pulse-skip modulation （PSM） for a DC-DC boost converter, to drive a luminance-regulated white light emitting diodes （WLEDs）. The presented control strategy not only retains most of the advantages and flexibilities of traditional digital PWM, but also reduces complexity and cost. Based on analyzing the principle of the presented control strategy, the white light emitting diode （WLED） driver is designed and simulated using the 0.6 μm CMOS process. Simulation results of the boost converter show that the power efficiency is above 76% for a full load, with a peak efficiency of 88% when supply voltage varies from 2.7 V to 5.5 V. The control strategy overcomes low efficiency for PWM mode with light load.

Large-areaβ-Ga_(2)O_(3) Schottky barrier diode and its application in DC-DC converters

We demonstrate superb large-area verticalβ-Ga_(2)O_(3)SBDs with a Schottky contact area of 1×1 mm^(2)and obtain a high-efficiency DC-DC converter based on the device.Theβ-Ga_(2)O_(3)SBD can obtain a forward current of 8 A with a forward volt-age of 5 V,and has a reverse breakdown voltage of 612 V.The forward turn-on voltage(VF)and the on-resistance(Ron)are 1.17 V and 0.46Ω,respectively.The conversion efficiency of theβ-Ga_(2)O_(3)SBD-based DC-DC converter is 95.81%.This work indicates the great potential of Ga_(2)O_(3)SBDs and relevant circuits in power electronic applications.

Optimized Model Based Controller with Model Plant Mismatch for NMP Mitigation in Boost Converter

In this paper,an optimized Genetic Algorithm(GA)based internal model controller-proportional integral derivative(IMC-PID)controller has been designed for the control variable to output variable transfer function of dc-dc boost converter to mitigate the effect of non-minimum phase(NMP)behavior due to the presence of a right-half plane zero(RHPZ).This RHPZ limits the dynamic performance of the converter and leads to internal instability.The IMC PID is a streamlined counterpart of the standard feedback controller and easily achieves optimal set point and load change performance with a single filter tuning parameterλ.Also,this paper addresses the influences of the model-based controller with model plant mismatch on the closed-loop control.The conventional IMC PID design is realized as an optimization problem with a resilient controller being determined through a genetic algorithm.Computed results suggested that GA–IMC PID coheres to the optimum designs with a fast convergence rate and outperforms conventional IMC PID controllers.

Simulation of multiphase boost DC-DC converter with the stable control strategy

The multiphase boost DC-DC converter with stable control strategy is presented. Multi- phase boost DC-DC converter is designed for high voltage and high power applications, and could be achieved by the adjustment of voltage doubler rectifiers on the secondary side of high frequency transformers. The stable control strategy for three phase boost DC-DC converter has been utilized during simulation in this study and this strategy can be extend to N-number of phases. The stable control strategy consists of only three voltage loops, which are sufficient for appropriate and efficient operation of three phase boost DC-DC converter. With the stable control strategy, the equal power balance sharing can be obtained between input and output. The stability of control strategy has been evaluated by simulating the multiphase boost DC-DC converter for the same and mismatch turn ratios of high frequency transformers. The simulation result is good and the objective of the strategy is a- chieved.

Design of a total-dose radiation hardened monolithic CMOS DC-DC boost converter

This paper presents the design and implementation of a monolithic CMOS DC-DC boost converter that is hardened for total dose radiation.In order to improve its radiation tolerant abilities,circuit-level and device-level RHBD（radiation-hardening by design） techniques were employed.Adaptive slope compensation was used to improve the inherent instability.The H-gate MOS transistors,annular gate MOS transistors and guard rings were applied to reduce the impact of total ionizing dose.A boost converter was fabricated by a standard commercial 0.35μm CMOS process.The hardened design converter can work properly in a wide range of total dose radiation environments,with increasing total dose radiation.The efficiency is not as strongly affected by the total dose radiation and so does the leakage performance.

Direct Model Predictive Control of Noninverting Buck-boost DC-DC Converter

In this paper, direct model predictive control(DMPC) of the noninverting buck-boost DC-DC converter with magnetic coupling between input and output is proposed. Unlike most of the other converters, the subject converter has the advantage of exhibiting minimum phase behavior in the boost mode. However, a major issue that arises in the classical control of the converter is the dead zone near the transition of the buck and boost mode. The reason for the dead zone is practically unrealizable duty cycles, which are close to zero or unity, of pulse width modulation(PWM) near the transition region. To overcome this issue, we propose to use DMPC. In DMPC, the switches are manipulated directly by the controller without the need of PWM.Thereby, avoiding the dead zone altogether. DMPC also offers several other advantages over classical techniques that include optimality and explicit current constraints. Simulations of the proposed DMPC technique on the converter show that the dead zone has been successfully avoided. Moreover, simulations show that the DMPC technique results in a significantly improved performance as compared to the classical control techniques in terms of response time, reference tracking, and overshoot.

基于新型CD单元的两相交错并联高增益Boost变换器

为减少基于电容-二极管(CD)升压单元的两相交错并联高增益Boost变换器的CD单元数量,提升变换器电压增益,提出一种最后两级CD单元电容并联充电、串联供电的新型两相交错Boost变换器拓扑结构,进一步发挥CD单元的升压能力。分析新型3CD、4CD两相交错并联Boost变换器的拓扑演化过程,提出新型NCD两相交错并联Boost变换器的拓扑演化规律。以新型4CD两相交错并联Boost变换器为例,分析变换器工作原理,以及电感、电容寄生电阻对变换器电压增益的影响。最后在StarSim硬件在环实验平台搭建1 kW的新型4CD单元交错并联Boost变换器,验证该文所提拓扑的正确性。

一种基于分数阶微积分的CCM Boost变换器准在线无源参数的数字孪生辨识方法

由于具有高性价比、准确性和数字化等优点,数字孪生已成为电力电子变换器故障趋势判断和预知维护的先进技术。针对当前电力电子变换器所建立的数字孪生模型尚未考虑实际电感、电容的分数阶特性的问题,基于分数阶微积分构建电力电子电路的预估-校正数字孪生模型,应用基于粒子群优化(particle swarm optimization,PSO)算法的孪生参数辨识方法对不同分数阶阶次下的电感值(L)和电容值(C)进行辨识,并计算出等效串联电阻。通过与现有方法对比,该方法不仅提高了实际电感和实际电容的辨识精度,还能辨识出不同阶次下与不同C下的分数阶参数。最后,搭建不同L和C及分数阶阶次的连续导通模式Boost变换器物理样机,并考虑不同工况条件与不同辨识次数等因素来进行实验验证。实验结果验证了所提模型与方法的有效性。

高增益耦合电感组合Boost-Cuk变换器

为了解决传统变换器电压增益低的问题,将Boost变换器与Cuk变换器进行并联集成,并利用耦合电感倍压技术提高变换器的电压增益。设计而成的高增益耦合电感组合Boost-Cuk变换器保留了Cuk变换器输出电流的连续性,新型结构中使用无源钳位来吸收漏感能量,对寄生电容与漏感谐振引起的电压尖峰起到约束作用,降低了开关管的电压应力。描述了变换器电感电流连续模式(Continuous current mode,CCM)下的运行特点,并进行了该变换器的参数设计。最后,通过搭建一台100 W的试验样机来求证理论的正确性。

基于预估-校正算法的分数阶Boost变换器倍周期分岔研究

基于电感电容本质是分数阶的事实,对分数阶Boost变换器的非线性动力学特性进行了深入研究。采用分数阶微积分的预估-校正算法,建立了Boost变换器的预估-校正模型,在此基础上得到了以参考电流、输入电压以及电容电感阶数为分岔参数的分岔图,研究了变换器的倍周期分岔和混沌行为,同时与整数阶Boost变换器的非线性动力学行为进行了比较。研究结果表明,在一定的工作条件下,随着变换器某些电路参数的变化,分数阶Boost变换器会出现分岔和混沌等非线性现象;在相同电路参数的条件下,整数阶和分数阶变换器的稳定参数域之间存在差异,与整数阶变换器相比,分数阶变换器的参数稳定区域更小,更真实地反映了Boost变换器的非线性动力学特性。

带感性负载的Buck-Boost变换器的非线性行为分析及优化控制

Buck-Boost变换器在某些参数发生变化时会呈现出丰富的非线性行为,这些行为将严重影响系统的稳定性,使得系统输出的电能质量劣化。文章基于实际变换器的负载特性,深入研究了感性阻抗负载下Buck-Boost变换器的非线性行为产生机理,提出了一种对数延迟反馈控制方法。该方法选取系统的输出延迟值与自身的值作差形成反馈信号;将该信号通过比例环节、求和环节和对数环节形成控制信号,以负反馈的形式施加于系统;最后基于稳定判据确定最优控制参数并对系统实施控制。为验证该方法的有效性,进行了大量的仿真实验,结果表明该方法能很好地抑制系统的非线性行为,扩展其稳定边界,改善系统输出的电能质量。

基于能量模型的临界导通模式Boost变换器软开关方法

在变换器高频化发展的趋势中,功率器件的软开关实现对变换效率的影响更加突出。无辅助电路的临界导通工作模式下,Boost变换器主开关管在特定增益下无法实现软开关。为此,该文提出一种能量模型及相应的软开关实现方法。首先,建立死区前后储能元件能量变化的数学模型。然后,结合死区起止时刻的能量平衡方程,研究软开关无法实现的电路机理。在此基础上,考虑开关管输出电容非线性特征,提出软开关实现方法,避免了复杂谐振过程的时域精确建模,提高软开关实现的准确性。最后,搭建500W实验样机进行实验,结果表明,相较于对谐振过程建模的传统时域模型,所提方法将实际开通电压降低47%,使峰值变换效率提升0.4%,进而验证了其有效性。

Super-Boost变换器的工作模式及输出纹波电压分析

Super-Boost变换器代替传统的充、放电模块可大大减小电源的质量和体积,提高其功率密度,因此在空间电力系统中具有广阔的应用前景。但由于Super-Boost变换器有多个功率元件,且存在电感电流反向流动特性,导致其供能模式及输出纹波电压较传统Boost变换器复杂。为了给Super-Boost变换器的分析和设计提供正确的理论指导,对Super-Boost变换器供能模式及输出纹波电压进行了深入研究。研究发现,电感L_(1)和L_(2)均存在连续导电模式、伪连续导电模式和伪断续导电模式等工作模式,建立各工作模式的临界电感和输出纹波电压解析数学模型,探讨峰值电流与电感间的关系,得到了满足设计要求的最小电容和最小电感,据此给出了变换器参数设计方法,实验结果验证了理论分析的正确性。

宽增益高效率级联式四开关Buck-Boost LLC变换器

为了解决变频控制的桥臂共用型四开关Buck-BoostLLC级联变换器磁性元件设计和优化困难的问题,提出一种二次侧为特殊全桥整流结构的级联式四开关Buck-Boost LLC变换器。通过控制二次侧开关管的交叠导通时间以拓宽变换器的电压增益。该变换器可根据不同的输入电压范围工作在交叠模式和整流模式;在不改变变换器参数的条件下将增益显著提高,能够适应更宽范围的输入电压,同时保持了变换器较高的工作效率。在两种工作模式的基础上,采用移相控制使变换器所有开关管实现零电压导通(ZVS),二极管实现零电流关断(ZCS)。结合状态平面轨迹分析法,对定频控制的级联式四开关Buck-Boost LLC变换器进行模态分析,并推导两种工作模式下的输入-输出表达式和开关管的软开关实现条件。最后,通过研制一台70~280 V输入、240 W/28 V输出的实验样机,验证了理论分析的正确性。

非最小相位的单电感双输出Buck-Boost变换器的复合控制方法

单电感双输出Buck-Boost (SIDO Buck-Boost)变换器在电感电流连续模式(CCM)下工作存在交叉影响以及非最小相位特性的问题.为了解决上述问题,提出基于储能函数的扩张状态观测器(ESO)的改进非奇异快速终端滑模(NFTSM)和自抗扰控制(ADRC)相结合的控制策略.设计主路控制器,对系统的传递函数进行拟合得到ADRC范式,利用该范式对主路进行解耦控制.设计支路控制器,采用改进型ESO对储能函数进行观测,并将观测值反馈补偿到非奇异快速终端滑模控制律中,达到支路解耦的效果.为了抑制滑模控制的抖振问题,对趋近律进行改进.利用Lyapunov理论证明系统稳定性.基于硬件在环(HIL)实验平台进行实验验证.结果表明,所提控制策略与PI控制策略以及基于ESO的滑模控制策略相比,在超调量和响应时间上具有较好的效果.

DC-DC Boost变换器系统的复合模态振荡分析

以DC-DC Boost变换器系统为研究对象,引入参数激励和外部激励,建立参外联合激励多尺度耦合动力学模型。当系统表现为严格共振关系时,且参数、外部激励频率与系统固有频率存在量级差时,把两激励项转化为单一周期激励项的函数形式,将此作为慢变参数,得到广义自治快子系统。主要探究了三种典型激励频率比下系统的复合模态振荡行为,借助单参数和双参数分岔图、复杂度谱熵图、转换相图等,分析了“非对称式光滑Fold-非光滑Fold型”、“周期性对称式非光滑Fold-Fold型”等复合模态振荡的产生机理和非光滑动力学行为特性。特别地,系统在不同频率比下的运行轨线结构,穿越非光滑分界面次数,簇发分岔点等均有所变化,从而导致含不同涡卷数的复合模态振荡。该研究为相关耦合电路的簇发振荡研究提供了理论基础及辅助分析模型。

基于开关流图法的Buck-Boost变换器小信号建模分析

阐述Buck-Boost变换器具有输出纹波低,电压可控等优点,广泛应用于新能源汽车电池发电、直流微电网。建立小信号模型有利于对电路系统主电路的控制和控制回路的设计。分析Buck-Boost变换器,利用开关流图法和信号支路的模型建立变换器的流图,从而推导出变换器的小型号模型。

DC–DC Converter with Pi Controller for BLDC Motor Fuzzy Drive System

The Brushless DC Motor drive systems are used widely with renewable energy resources.The power converter controlling technique increases the performance by novel techniques and algorithms.Conventional approaches are mostly focused on buck converter,Fuzzy logic control with various switching activity.In this proposed research work,the QPSO(Quantum Particle Swarm Optimization algorithm)is used on the switching state of converter from the generation unit of solar module.Through the duty cycle pulse from optimization function,the MOSFET(Metal-Oxide-Semiconductor Field-Effect Transistor)of the Boost converter gets switched when BLDC(Brushless Direct Current Motor)motor drive system requires power.Voltage Source three phase inverter and Boost converter is controlled by proportional-integral(PI)controller.Based on the BLDC drive,the load utilized from the solar generating module.Experimental results analyzed every module of the proposed grid system,which are solar generation utilizes the irradiance and temperature depends on this the Photovoltaics(PV)power is generated and the QPSO with Duty cycle switching state is determined.The Boost converter module is boost stage based on generation and load is obtained.Single Ended Primary Inductor Converter(SEPIC)and Zeta converter model is compared with the proposed logic;the proposed boost converter achieves the results.Three phase inverter control,PI,and BLDC motor drive results.Thus the proposed grid model is constructed to obtain the better performance results than most recent literatures.Overall design model is done by using MATLAB/Simulink 2020a.