Numerical simulation of deep-hole resistivity anomaly caused by drilling construction in Xinfengjiang geoelectric station

The Xinfengjiang reservoir in Guangdong Province is one of the large reservoirs that have triggered earthquakes of magnitude greater than 6.Numerous earthquakes have occurred since the impoundment of the reservoir,making it one of the most active seismic zones in south China.In 2015,a set of deep-hole resistivity anomalies was observed in the Heping geoelectric station in Dongyuan county,located near the Xinfengjiang reservoir.After a field investigation,we found that a planned well drilling construction of new measuring channels was being carried out during that corresponding period of time.After careful comparison and analysis on the basis of the collected raw data,we had a reason to believe that drilling construction,rather than the inducement of the Xinfengjiang reservoir,was the main culprit for those unusual georesistivity values.So as to verify the above conjecture,we constructed a series of 3D finite element models based on the geological and hydrological infor-mation around Heping station and analyzed the drilling disturbances,respectively.Some significant conclusions were finally drawn according to the precise numerical simulation.This study gives a good example by combining numerical simulation with engineering practice as a way to understand the root cause of georesistivity anomalies in reality.

Dynamic Interaction Analysis of Coupled Axial-Torsional-Lateral Mechanical Vibrations in Rotary Drilling Systems

Maintaining the integrity and longevity of structures is essential in many industries,such as aerospace,nuclear,and petroleum.To achieve the cost-effectiveness of large-scale systems in petroleum drilling,a strong emphasis on structural durability and monitoring is required.This study focuses on the mechanical vibrations that occur in rotary drilling systems,which have a substantial impact on the structural integrity of drilling equipment.The study specifically investigates axial,torsional,and lateral vibrations,which might lead to negative consequences such as bit-bounce,chaotic whirling,and high-frequency stick-slip.These events not only hinder the efficiency of drilling but also lead to exhaustion and harm to the system’s components since they are difficult to be detected and controlled in real time.The study investigates the dynamic interactions of these vibrations,specifically in their high-frequency modes,usingfield data obtained from measurement while drilling.Thefindings have demonstrated the effect of strong coupling between the high-frequency modes of these vibrations on drilling sys-tem performance.The obtained results highlight the importance of considering the interconnected impacts of these vibrations when designing and implementing robust control systems.Therefore,integrating these compo-nents can increase the durability of drill bits and drill strings,as well as improve the ability to monitor and detect damage.Moreover,by exploiting thesefindings,the assessment of structural resilience in rotary drilling systems can be enhanced.Furthermore,the study demonstrates the capacity of structural health monitoring to improve the quality,dependability,and efficiency of rotary drilling systems in the petroleum industry.

DEVELOPMENT AND EXPERIMENT OF NEW AlTiN COATED DRILLS FOR HIGH EFFICIENCY DRY DRILLING OF 40Cr

Two new AlTiN coated cemented carbide drills with Al content of 40% and 55% in weight are developed for high efficiency dry drilling of 40Cr. By studying tool durability, machined hole quality, tool wear mechanism, chip deformation, and lubrication, the dry drilling performance of the two kinds of coated drills is analyzed. Experimental results show that the AlTiN coated drills are suitable for high efficiency dry drilling and can obtain higher quality of machined holes. The tool durability of the drill with 55% Al content is 1. 3 times of that of the drill with 40% Al content at the cutting speed of 90 m/min. The wear mechanism of two AlTiN coatings are studied in experiments. During dry drilling process, oxidative wear appears in both two kinds of drills. The oxide film is formed on the top of the coated drill containing Al content of 55%. And the oxide film helps to increase its high temperature resistance and decrease the coating flaking, thus the drill is failed because of coating subsidence. The drill with less Al content is failed due to peeling and breakage. The lubricated condition in dry drilling is improved by the high Al content coating. It helps to reduce the cutting deformation and benefits to improve the quality of machined holes. The AlTiN coating with higher Al content shows longer tool life and higher quality of machined holes in high efficiency dry drilling. Its tool life increases by 30% compared with that of the coating with less Al content.

Development and application of turbodrills in hot dry rock drilling

The strata of hot dry rock(HDR) are usually igneous rocks with high temperature which are challenging for drilling activities. This paper deals with the key technology and research of turbodrills, introduced the application of turbodrills in HDR drilling at home and broad, and analyzed the field application cases. With the advancement such as low speed high torque turbodrill, reduction turbodrills, independent spindlesection and PDC bearings and so on, the application of turbodrills has widely expanded. The application of high-temperature turbodrills in Fenton Hill, HDR geothermal wells, high-temperature formation in Tahe oilfield all proved that turbodrills are the best downhole motors in deep high-temperature HDR drilling, thus they deserve further research and generalization.

Deep-Hole Inner Diameter Measuring System Based on Non-contact Capacitance Sensor

A precise aperture measuring system of small deep holes with capacitance sensors is presented. Based on the working principle of non-contact capacitance sensors, influence of the edge effect of gauge head is studied, and one capacitance sensor for measuring the aperture of the small blind holes or through holes is introduced. The system is composed of one positioning device, one aperture measuring capacitance sensor, one measuring circuit, and software. This system employs visual CCD and two-dimensional mic...

Effectiveness analysis of methane-drainage by deep-hole controlled pre-splitting blasting for preventing coal and gas outburst

In the study of the application effectiveness of deep-hole controlled pre-splittingblasting technology,it was found through laboratory micro test and field study on a mine insouth China that under the technology,coal masses produce many irreversible cracks.Afterblasting,the nearer the distance from blasting hole,the larger the BET surface areaand volume ratio of the infiltration pore are;they increased by 11.47%and 5.73%,respectively.The coefficient of air permeability is increased 4 times.After 3 months,the gasdrainage rate was increased by 66%.In the first 15 days,the cumulative pumped gas was1.93 times of blasting before.The average absolute gas emission decreased by 63.46%.Experimental results show that deep-hole controlled pre-splitting blasting not only preventscoal and gas outburst,but also gives good economic results.

Numerical simulation and experiment analysis of improving permeability by deep-hole presplitting explosion in high gassy and low permeability coal seam

Created a new damage model for explosive for LS-DYNA3D,taking advantageof the Taylor method aimed at the high gassy and low permeability coal seam,and numericallysimulated and analyzed the deep-hole presplitting explosion.The entire processof explosion was represented,including cracks caused by dynamic pressure,transmissionand vibration superposition of stress waves,as well as cracks growth driven by gas generatedby explosion.The influence of the cracks generated in the process of explosion andthe performance of improving permeability caused by the difference of interval between.explosive holes were analyzed.A reasonable interval between explosive holes of deepholepresplitting explosions in high gassy and low permeability coal seams was proposed,and the resolution of gas drainage in high gassy and low permeability coal seam was putforward.

Mechanical behavior of drillstring with drag reduction oscillators and its effects on sliding drilling limits

Practice has proved that drag reduction oscillators can decrease the axial friction and increase wellbore extension effectively in sliding drilling operations.However,the complicated mechanical behavior of drillstring with drag reduction oscillators has not been revealed sufficiently.In this paper,the mechanical model of drillstring with drag reduction oscillators is established by considering the friction nonlinearity.Further introducing the initial conditions,boundary conditions and continuity conditions,the finite differential equation of drillstring vibration is obtained and solved.The new model has been applied to a case study,in which the drag reduction effects of drillstring with and without oscillators are compared and the effects of relevant factors on drag reduction are analyzed.The results show that the hook loads increase obviously by reducing downhole average friction coefficient for drillstring with oscillators.Increasing vibration amplitude of the drag reduction oscillator can decrease axial friction,but the vibration frequency is nearly irrelevant to drag reduction.Increasing number of drag reduction oscillators can decrease axial friction,but may lead to large hydraulic power loss and high risk of drillstring fatigue.Therefore,there is an optimal number of drag reduction oscillators.The re search re sults are of significant guiding significance for optimal design and safety control in sliding drilling operations.

Wear State Recognition of Drills Based on K-means Cluster and Radial Basis Function Neural Network

Drill wear not only affects the surface smoothness of the hole, but also influences the life of the drill. Drill wear state recognition is important in the manufacturing process, which consists of two steps： first, decomposing cutting torque components from the original signals by wavelet packet decomposition （WPD）; second, extracting wavelet coefficients of different wear states （i.e., slight, normal, or severe wear） with signal features adapting to Welch spectrum. Finally, monitoring and recognition of the feature vectors of cutting torque signal are performed by using the K-means cluster and radial basis function neural network （RBFNN）. The experiments on different tool wears of the multivariable features reveal that the results of monitoring and recognition are significant and effective.

Optimization of ice cuttings transportation by cable-suspended core auger drills

Ice cores contain an abundance of information about the Earth＇s climate in the past, and recovered from shallow drilling down to 300-350 m give sufficient information for reconstructing of the last climatic changes and for monitoring of pollution from human being. Cable-suspended core auger drills use an armored cable with a winch to provide power to the down-hole motor system and to retrieve the down-hole unit. Because of their lightweight, convenient transportation and installation, high penetration rates and low power consumption, core auger drills are widely used for shallow drilling in ice. Nowadays at least 14 types of auger electromechani- cal drills were designed and tested in different foreign and national glaciological laboratories. However, auger options were usually determined by experience, and the main parameters （ helix angle of the fights and rotational speed） are varied in a wide range from drill to drill. If parameters of auger are not chosen properly, poorly en- gineered drills had troubles with low efficiency of cuttings transportation, jam of ice cuttings, repeated fragmen- tation, cutters icing and stop penetration, abnormal power consumption, high rotation torques, and so on. Thus, this paper presents the method of optimization of iee cuttings transportation of cable-suspended core auger drill on the base of the theory of rotary auger. As the result, the optimal helix angle was determined correspond- ing to the rotational speed from the transportation efficiency point of view.

Drilling-based measuring method for the c-φ parameter of rock and its field application

The technology of drilling tests makes it possible to obtain the strength parameter of rock accurately in situ. In this paper, a new rock cutting analysis model that considers the influence of the rock crushing zone(RCZ) is built. The formula for an ultimate cutting force is established based on the limit equilibrium principle. The relationship between digital drilling parameters(DDP) and the c-φ parameter(DDP-cφ formula, where c refers to the cohesion and φ refers to the internal friction angle) is derived, and the response of drilling parameters and cutting ratio to the strength parameters is analyzed. The drillingbased measuring method for the c-φ parameter of rock is constructed. The laboratory verification test is then completed, and the difference in results between the drilling test and the compression test is less than 6%. On this basis, in-situ rock drilling tests in a traffic tunnel and a coal mine roadway are carried out, and the strength parameters of the surrounding rock are effectively tested. The average difference ratio of the results is less than 11%, which verifies the effectiveness of the proposed method for obtaining the strength parameters based on digital drilling. This study provides methodological support for field testing of rock strength parameters.

Development of Diamond-Coated Drills

Compared with the sintered polycrystalline diamond, the deposited thin film diamond has the great advantage on the fabrication of cutting tools with complex geometries such as drills. Because of their low costs for fabrication equipment and high performance on high speed machining non-ferrous metals and alloys, metal-compound materials, and hard brittle non-metals, diamond-coated drills find great potentialities in the commercial application. However, the poor adhesion of the diamond film on the substrate becomes the main technical barriers for the successful development and commercialization of diamond-coated tools. In this paper, diamond thin films were deposited on WC-Co based drills by the electron aided hot filament chemical vapor deposition (EACVD). A new multiple chemical pre-treatment technology including microwave oxidation, reaction in alkaline solution and cleaning by ultrasonic treatment in acid solution was developed and affects on the diamond adhesion strength, nucleation and surface morphology were investigated. At the same time, a special setup to fabricate diamond-coated drills was also developed and then the novel CVD process based on the varied parameters controlling model was presented, therefore the uniform quality and homogenized thickness of diamond coating could be available. From practical utilization viewpoint, the cutting performance of the diamond-coated drill was studied by drilling SiC particle reinforced aluminum matrix composite. The satisfied wear resistance and decrease of torque and thrust led to the long life of this kind of drill. This paper exhibited the meaningful work for the development of cutting tools with complex geometries and further extended the application of diamond material.

Synthetic polymers:A review of applications in drilling fluids

With the growth of deep drilling and the complexity of the well profile,the requirements for a more complete and efficient exploitation of productive formations increase,which increases the risk of various complications.Currently,reagents based on modified natural polymers(which are naturally occurring compounds)and synthetic polymers(SPs)which are polymeric compounds created industrially,are widely used to prevent emerging complications in the drilling process.However,compared to modified natural polymers,SPs form a family of high-molecular-weight compounds that are fully synthesized by undergoing chemical polymerization reactions.SPs provide substantial flexibility in their design.Moreover,their size and chemical composition can be adjusted to provide properties for nearly all the functional objectives of drilling fluids.They can be classified based on chemical ingredients,type of reaction,and their responses to heating.However,some of SPs,due to their structural characteristics,have a high cost,a poor temperature and salt resistance in drilling fluids,and degradation begins when the temperature reaches 130℃.These drawbacks prevent SP use in some medium and deep wells.Thus,this review addresses the historical development,the characteristics,manufacturing methods,classification,and the applications of SPs in drilling fluids.The contributions of SPs as additives to drilling fluids to enhance rheology,filtrate generation,carrying of cuttings,fluid lubricity,and clay/shale stability are explained in detail.The mechanisms,impacts,and advances achieved when SPs are added to drilling fluids are also described.The typical challenges encountered by SPs when deployed in drilling fluids and their advantages and drawbacks are also discussed.Economic issues also impact the applications of SPs in drilling fluids.Consequently,the cost of the most relevant SPs,and the monomers used in their synthesis,are assessed.Environmental impacts of SPs when deployed in drilling fluids,and their manufacturing processes are identified,together with advances in SP-treatment methods aimed at reducing those impacts.Recommendations for required future research addressing SP property and performance gaps are provided.

Major Approaches on the Piezoelectric Device, Drills and Saws to Orthognathic Surgery: A Systematic Review

Introduction: The incidence of lesions of sensory and motor nerves associated with oral and maxillofacial surgery is often underestimated, representing around 32.0% of all lesions, and orthognathic surgery contributes 12.3% to these lesions. Thus, the use of piezosurgery (PiZCi) has been indicated in several procedures within oral and maxillofacial surgery due to a number of advantages over conventional drill and saw techniques. Objective: to analyze the main literature on the use of the piezoelectric device in relation to the use of drills and to orthognathic surgery in dentistry. Methods: A total of 41 articles were found involving Orthognathic Surgery, Piezoelectric Device, Drills Device, Saws Device, and Efficiency. Initially, it was held the exclusion existing title and duplications following the interest described this work. After this process, the summaries were evaluated, and a new exclusion was held. 29 articles were included and discussed in this study. Initially, the keywords were determined by searching the DeCS tool (Descriptors in Health Sciences, BIREME base) and later verified and validated by MeSh system (Medical Subject Headings, the US National Library of Medicine). Results and conclusion: It was concluded that the piezoelectric device has excelled with an effective surgical technique, being able to be indicated in the most diverse areas of the oral surgery, providing accurate, clean and minimally traumatic osteotomies for the soft tissues, intraoperative bleeding, when compared to conventional surgery using drills and/or saws.

Quality and Method of Management of Drinking Water in Rural Areas in Benin: Case of Artesian Drills of Dogbo Ahomey in the Borough of Tota, Municipality of Dogbo

The objective of this study is to assess the quality of the artesian borehole water consumed by the population of the village of Dogbo Ahomey in order to prevent pathologies on the populations. Methodology and Results: The household surveys were supplemented by a campaign to analyze the water samples in the laboratory. The samples were analyzed according to the standardized methods of the American Public Health Association (APHAAWWA-WPCF, 1994). A total of twenty (20) physico-chemical parameters and four (04) microbiological parameters were used to assess the quality of the different water samples. The results of the physico-chemical analysis showed that the water samples studied present values that are below the standards recommended by the WHO and by the Beninese standards for the quality of drinking water (Standards, 2001). From a microbiological analysis point of view, of the four samples studied, two show strong pollution by germs. This could be a significant health risk for households who take water from these sources to meet their needs.

Improvements of drilling fluid processing for cable-suspended electromechanical drills

Deep ice drilling in Polar Regions plays a key role in paleo-climate, microbiological and glaciological researches. For deep ice and subglacial coring the special purpose-built electromechanical cable-suspended drills with bottom-hole circulation are designed and explored. Used at present drilling fluid circulation systems are specified by very high fluid wastes during processing. Measurements in deep drilling projects in Antarctic and Greenland ice sheets showed that 25%-40% of the drilling fluid, pumped into the hole, is retrieved to the surface with cable and drill, and up to 45% of retrieved fluid goes to waste. This leads not only to increasing of the fluid consumption and cost of the project in general but also to severe contamination of air, surface and near-surface snow-firn layers at the drilling site. In order to reduce wastes and environmental impact, it is proposed to modify drilling fluid processing system by avoiding of evaporation and leakages of fluid as far as practicable. Drilling fluid is prepared and pumped into the hole according to predetermined program on semiautomatic mode, and volume and density of blended and pumped into the hole drilling fluid are measured continuously. Components of the drilling fluid are stored and mixed in the special closed containers equipped by pressure relief valves. Separation of drilling fluid from ice cuttings is carried out by two steps: firstly, fluid is separated with hydro extractor and then with thermal separator. To reduce the amount of removed drilling fluid with cable special squeezing collar is installed on the borehole mouth. All these arrangements are able to decrease drilling fluid wastes in many times.

The Conversion of Non-Dispersed Polymers into Low-Potassium Anti-Collapse Drilling Fluids

Different drillingfluid systems are designed according to mineral composition,lithology and wellbore stability of different strata.In the present study,the conversion of a non-dispersed polymer drillingfluid into a low potas-sium anti-collapsing drillingfluid is investigated.Since the two drillingfluids belong to completely different types,the key to this conversion is represented by new inhibitors,dispersants and water-loss agents by which a non-dispersed drillingfluid can be turned into a dispersed drillingfluid while ensuring wellbore stability and reason-able rheology(carrying sand—inhibiting cuttings dispersion).In particular,the(QYZ-1)inhibitors and(FSJSS-2)dispersants are used.The former can inhibit the hydration expansion capacity of clay,reduce the dynamic shear force and weaken the viscosity;the latter can improve the sealing effect and reduce thefiltrate loss.The results have shown that after adding a reasonable proportion of these substances(QYZ-1:FSJSS-2)to the non-dispersed polymer drillingfluid,while the apparent viscosity,plastic viscosity,structural viscosity andfluidity index under-went almost negligible changes,the dynamic plastic ratio increased,and thefiltration loss decreased significantly,thereby indicating good compatibility.According to the tests(conducted in the Leijia area),the density was 1.293 g/cm3,and after standing for 24 h,the SF(static settlement factor)was 0.51.Moreover,thefiltration loss was reduced to 4.0 mL,the rolling recovery rate reached 96.92%,with excellent plugging and anti-collapse performances.

The Effects of Fluid Rheology and Drillstring Eccentricity on Drilling Hydraulics

Accurate determination of hydraulic parameters such as pressure losses, equivalent circulation density (ECD), etc. plays profound roles in drilling, cementing and other well operations. Hydraulics characterization requires that all factors are considered as the neglect of any could become potential sources of errors that would be detrimental to the overall well operation. Drilling Hydraulics has been extensively treated in the literature. However, these works almost entirely rely on the assumption that the drill string lies perfectly at the center of the annulus—the so-called “concentric annulus”. In reality, concentricity is almost never achieved even when centralizers are used. This is because of high well inclination angles and different string geometries. Thus, eccentricity exists in practical oil and gas wells especially horizontal and extended reach wells (ERWs) and must be accounted for. The prevalence of drillstring (DS) eccentricity in the annulus calls for a re-evaluation of existing hydraulic models. This study evaluates the effect of drilling fluid rheology types and DS eccentricity on the entire drilling hydraulics. Three non-Newtonian fluid models were analyzed, viz: Herschel Bulkley, power law and Bingham plastic models. From the results, it was observed that while power law and Bingham plastic models gave the upper and lower hydraulic values, Herschel Bulkley fluid model gave annular pressure loss (APL) and ECD values that fall between the upper and lower values and provide a better fit to the hydraulic data than power law and Bingham plastic fluids. Furthermore, analysis of annular eccentricity reveals that APLs and ECD decrease with an increase in DS eccentricity. Pressure loss reduction of more than 50% was predicted for the fully eccentric case for Herschel Bulkley fluids. Thus, DS eccentricity must be fully considered during well planning and hydraulics designs.

Research progress and development of deep and ultra-deep drilling fluid technology

The research progress of deep and ultra-deep drilling fluid technology systematically reviewed,the key problems existing are analyzed,and the future development direction is proposed.In view of the high temperature,high pressure and high stress,fracture development,wellbore instability,drilling fluid lost circulation and other problems faced in the process of deep and ultra-deep complex oil and gas drilling,scholars have developed deep and ultra-deep high-temperature and high-salt resistant water-based drilling fluid technology,high-temperature resistant oil-based/synthetic drilling fluid technology,drilling fluid technology for reservoir protection and drilling fluid lost circulation control technology.However,there are still some key problems such as insufficient resistance to high temperature,high pressure and high stress,wellbore instability and serious lost circulation.Therefore,the development direction of deep and ultra-deep drilling fluid technology in the future is proposed:(1)The technology of high-temperature and high-salt resistant water-based drilling fluid should focus on improving high temperature stability,improving rheological properties,strengthening filtration control and improving compatibility with formation.(2)The technology of oil-based/synthetic drilling fluid resistant to high temperature should further study in the aspects of easily degradable environmental protection additives with low toxicity such as high temperature stabilizer,rheological regulator and related supporting technologies.(3)The drilling fluid technology for reservoir protection should be devoted to the development of new high-performance additives and materials,and further improve the real-time monitoring technology by introducing advanced sensor networks and artificial intelligence algorithms.(4)The lost circulation control of drilling fluid should pay more attention to the integration and application of intelligent technology,the research and application of high-performance plugging materials,the exploration of diversified plugging techniques and methods,and the improvement of environmental protection and production safety awareness.