According to the bio-characteristics of the lower and upper cavity surfaces of dental restoration, a stitching approach is proposed based on a virtual zipper working mechanism and a minimization of the surface total c...According to the bio-characteristics of the lower and upper cavity surfaces of dental restoration, a stitching approach is proposed based on a virtual zipper working mechanism and a minimization of the surface total curvature energy, which is used to resolve the stitching problems existing during computer-aided design for dental restorations. First, the two boundaries corresponding to the lower and upper surfaces are triangulated based on the zipper working mechanism to generate the initial stitching surface patch, of which the edges are distributed uniformly between the boundaries. Secondly, the initial stitching surface patch is subdivided and deformed to reconstruct an optimized surface patch according to the bio-characteristics of the teeth. The optimized surface patch is minimally distinguishable from the surrounding mesh in smoothness and density, and it can stitch the upper and lower cavity surfaces naturally. The experimental results show that the dental restorations obtained by the proposed method can satisfy both the shape aesthetic and the fitting accuracy, and meet the requirements of clinical oral medicine.展开更多
This paper aims to investigate if the dental restoration of nickel-chromium based alloy(Ni-Cr) leads to the enhanced excretions of Ni and Cr in urine.Seven hundred and ninety-five patients in a dental hospital had sin...This paper aims to investigate if the dental restoration of nickel-chromium based alloy(Ni-Cr) leads to the enhanced excretions of Ni and Cr in urine.Seven hundred and ninety-five patients in a dental hospital had single or multiple Ni-Cr alloy restoration recently and 198 controls were recruited to collect information on dental restoration by questionnaire and clinical examination.Urinary concentrations of Ni and Cr from each subject were measure by graphite furnace atomic absorption spectrometry.Compared to the control group,the urinary level of Ni was significantly higher in the patient group of < 1 month of the restoration duration,among which higher Ni excretions were found in those with either a higher number of teeth replaced by dental alloys or a higher index of metal crown not covered with the porcelain.Urinary levels of Cr were significantly higher in the three patient groups of <1,1 to <3 and 3 to <6 months,especially in those with a higher metal crown exposure index.Linear curve estimations showed better relationships between urinary Ni and Cr in patients within 6-month groups.Our data suggested significant increased excretions of urinary Ni and Cr after dental restoration.Potential short- and long-term effects of Ni-Cr alloy restoration need to be investigated.展开更多
Since the last two decades, restorative dentistry has been witnessing an increased acceptance of the use of the well-known all-ceramic materials for the fabrication of single dental restorations, such as inlays, onlay...Since the last two decades, restorative dentistry has been witnessing an increased acceptance of the use of the well-known all-ceramic materials for the fabrication of single dental restorations, such as inlays, onlays, crowns, anterior and posterior fixed partial dentures (PFPDs). These restorations certainly offer the potential for better biocompatibility coupled with superior aesthetic qualities, especially when compared with the conventional prostheses made from porcelain that is fused with metal ceramic restorations. However, brittleness and extreme sensitivity of all-ceramic materials to micro-like defects or cracks that are inherently present, or may grow, in their microstructure during different laboratory fabrication steps, during necessary clinical adjustments, or from post-placement chewing activity, remain major shortcomings of these dental restorations. In fact, many researchers are of the opinion that the improved mechanical properties can significantly improve the lifetime of all-ceramic restorations and result in enhanced reliability. Therefore, efforts of researchers, as well as manufacturers, have been directed towards the improvement of the mechanical properties in order to overcome such limitations. This article reviews the characterization of the most important mechanical properties that can delineate the behavior of all-ceramic dental materials upon loading. These include fracture mechanics, the brittle nature of ceramics, the relationship between microstructural features and fracture behavior, sources of cracks and flaws that may initiate a fracture and the effect of different fabrication procedures and/or clinical adjustments on the mechanical behavior of dental ceramics are also reviewed and discussed.展开更多
<strong>Background:</strong> Diabetes increases periodontal disease risk and its complications, which are worsened with age or faulty restorations. <strong>Aim:</strong> Evaluate periodontal he...<strong>Background:</strong> Diabetes increases periodontal disease risk and its complications, which are worsened with age or faulty restorations. <strong>Aim:</strong> Evaluate periodontal health among patients with diabetes treated with different dental restorations. <strong>Materials and Methods:</strong> This comparative cross-sectional study was conducted at the faculty of dentistry, Najran University, KSA, from March 2018 to February 2020. It included 260 diabetics, treated with different dental restorations, divided into four groups, each comprising 65 patients aged 45 - 60 years: Group 1 (G1), no restorations (control group);Group 2 (G2), Class II amalgam restorations;Group 3 (G3), Class II composite resin restorations;and Group 4 (G4), three-unit posterior metal ceramic prostheses. The Ages of all restorations ranged from 8 to 10 years. All groups were assessed for the Plaque Index (PI) and Gingival Index (GI), Overhangs Rate (OR), Alveolar Bone Loss (ABL) (the latter two using panoramic X-ray). HbA1c and duration of participants were also assessed and compared. <strong>Results:</strong> The mean HbA1c results of the groups ranged from 8.1% to 9.5%, and their mean diabetes durations ranged from 7.2 to 12 years. All the groups showed worse periodontal scores, ranging from 2.45 - 2.95 for PI and 2.25 - 2.8 for GI. G2 had higher scores than G1 and G3 (<em>p</em> < 0.001). G4 had the highest two recorded scores (<em>p</em> < 0.001). G2 had a higher rate of overhangs than G3 (<em>p</em> < 0.037). The mean ABL was 44% (SD 6.4) for G1, 56.0% (SD 6.7) for G2, 46.5% (SD 5.8) for G3, and 74.5% (SD 6.4) for G4. The lowest values were recorded in G1 and G3 (<em>p</em> = 0.987). The highest value was observed in G4, which was significantly higher than other groups (<em>p</em> < 0.001). <strong>Conclusion: </strong>The worse periodontal parameters among subjects treated with either three-unit metal ceramic or Class II amalgam restorations indicated severe periodontal destruction. Untreated subjects and subjects treated with Class II composite resin had relatively better periodontal status.展开更多
The novel dental ceramics can be fabricated at lower temperatures when sol-gel derived lithium disilicate glass ceramics(LDGC)was used as an additive for yttria stabilized tetragonal zirconia polycrystalline(Y-TZP)cer...The novel dental ceramics can be fabricated at lower temperatures when sol-gel derived lithium disilicate glass ceramics(LDGC)was used as an additive for yttria stabilized tetragonal zirconia polycrystalline(Y-TZP)ceramics.The effect of LDGC on the sintering,mechanical,and translucent properties of Y-TZP ceramics was investigated in the present study.The results showed that the LDGC additive effectively improved the densification of Y-TZP at 1100℃,which was much lower than the sintering temperature for pure Y-TZP.When sintered at 1100℃,the Y-TZP with 1 wt%LDGC reached a relative density of 95.45%,and prossessed a flexural strength of 482.4 MPa and a fracture toughness of 5.94 MPa-m12.Moreover,its translucency was also improved.While,the addition of LDGC could result in an escape of yttrium atoms from the grain lattice of zirconia,which induced the tetragonal-monoclinic transformation of zirconia and abnormal growth of monoclinic grains.The escaped yttrium atoms diffused into the intergranular glass phase.The results indicated that the novel Y-TZP-LDGC ceramics has a great potential to be used for all-ceramic restorations.展开更多
Dental restorative materials with high mechanical properties and biocompatible performances are promising.In this work,polymer-infiltrated-ceramic-network materials(PICNs)were fabricated via infiltrating polymerizable...Dental restorative materials with high mechanical properties and biocompatible performances are promising.In this work,polymer-infiltrated-ceramic-network materials(PICNs)were fabricated via infiltrating polymerizable monomers into porous ceramic networks and incorporated with hydroxyapatite nano-powders.Our results revealed that the flexural strength can be enhanced up to 157.32 MPa,and elastic modulus and Vickers hardness can be achieved up to 19.4 and 1.31 GPa,respectively,which are comparable with the commercial computer-aided design and computer-aided manufacturing(CAD/CAM)blocks.Additionally,the adhesion and spreading of rat bone marrow mesenchymal stem cells(r BMSCs)on the surface of such materials can be improved by adding hydroxyapatite,which results in good biocompatibility.Such PICNs are potential applicants for their application in the dental restoration.展开更多
The wear rate of dental restoration materials on fixed, removable, and implant prostheses is important in the maintenance of cuspate form, masticatory efficiency and occlusal stability. Many permanent restoration mate...The wear rate of dental restoration materials on fixed, removable, and implant prostheses is important in the maintenance of cuspate form, masticatory efficiency and occlusal stability. Many permanent restoration materials such as composite, amalgam, gold, or porcelain show enough resistance to wear, but the wear rates of newly developed materials are generally unknown. To evaluate the wear rate of these dental materials, in vivo (clinic) and in vitro methods can be used. Since in vivo investigations are expensive, time consuming, and difficult to standardize, various in vitro methods have been developed. The use of a chewing machine is considered the best method, because a variety of wear mechanisms, temperature changes, and chemical effects of food and drink can be simulated simultaneously. This paper describes a dual axis chewing simulator for in vitro wear test of dental restoration materials. It consists of 8 test chambers, two stepper motors and related mechanism, a hot and cool water circle system, and a control unit. In the chambers, samples and antagonists make chewing movements vertically and Albert Ludwigs University, School of dentistry, Freiburg, Germany (Lü XY, Kern M and Strub JR) horizontally driven by the stepper motors so that the gnashing and slippage of two teeth against each other is simulated. A weighted test object is programmed to collide with a sample under precise operator control. The antagonists strike against the samples at various speeds from a slow nudge to snapping. Sample holders are designed for installation of varying samples, from single teeth to complete dentures. Two baths, six valves, and a group of pipes are used for the thermocycling. The machine can simulate various chewing modes in the mouth, including fully programmable thermal water cycling between 5℃ and 60℃ The control unit consists of a computer system with a built in specific program. Important operations such as “Start”, “Zero point”, and “Stop” are carried out by pressing the function keys on the front board of the unit. During the programming process and the simulation, several test modes and relevant test parameters are shown on the monitor. The control unit is connected via a series of interfaces to different controlled parts of the machine, such as the stepper motors and the pumps of cool and warm water.展开更多
BACKGROUND Tooth defects can cause elongation of occlusal teeth,leading to insufficient repair space.The combination of dental implant restoration and orthodontic treatment of oblique adjacent teeth has a significant ...BACKGROUND Tooth defects can cause elongation of occlusal teeth,leading to insufficient repair space.The combination of dental implant restoration and orthodontic treatment of oblique adjacent teeth has a significant therapeutic effect.AIM To explore clinical efficacy,bone density,and follow-up of implant and orthodontic treatment for patients with inclined adjacent teeth.METHODS In total,98 patients with oblique adjacent teeth were randomly assigned to implant restoration combined with orthodontic treatment(group A,n=49)or to receive implant restoration alone(group B,n=49).Changes in alveolar ridge bone density and apical bone density were observed before and after treatment in the two groups.Changes in chewing function and language function were compared between the two groups of patients.Follow-up lasted for 12 mo after repair to observe any adverse reactions in the oral cavity.RESULTS The clinical effective rates of group A and group B were 97.96%and 85.71%,respectively,with group A having a higher clinical effective rate than group B.After treatment,the bone density of the alveolar ridge and apical bone in both groups decreased compared to before treatment,while the chewing and language functions improved.The changes in various indicators in group A were more significant.After treatment,the satisfaction rate of group A(97.96%)was higher than that of group B(79.59%).The incidence of adverse reactions in group A(2.04%)was lower than that in group B(24.49%).CONCLUSION The amalgamation of implant restoration and orthodontic treatment for adjacent tilted teeth demonstrates notable clinical efficacy,diminishes alveolar bone resorption,and fosters patient functional rehabilitation while exhibiting negligible adverse reactions.展开更多
Objective To evaluate the effect of midazolam alone on sedation in young children for dental restorative care. Methods Forty children, aged 5 to 10 years with a mean age of 7.3 years, participated in this study. Twent...Objective To evaluate the effect of midazolam alone on sedation in young children for dental restorative care. Methods Forty children, aged 5 to 10 years with a mean age of 7.3 years, participated in this study. Twenty-one patients were assigned to intervention group received 0. 5 mg/kg of oral midazolam 20 minutes prior to the beginning of dental treatment, and 19 patients in control group received placebo liquid 20 minutes before treatment. All patients received painless local anesthetic injection and were restrained with children's board and bands. Blood pressure ( BP), heart rate (HR), oxygen saturation, treatment compliance scores of the Ramsay scale, the Briekopf and Butmer scale, Frankl scale, and the Houpt scale were recorded. Each procedure was taped and all the data were evaluated every 5 minutes by an anesthetist or experienced dentist who was unaware of the drug given to the child. Results HR in intervention group (82. 5 ± 5.1 bpm) was much lower than that in control group (95.2 ± 8.9 bpm; F=31.20, P 〈0. 001 ). Intervention group had a significantly lower systolic BP level (94.8±5.6 mmHg) than control group (98.5±5.5 mm Hg; F=4. 34, P =0. 04), but the diastolic BP (63.0 ± 3.5 mm Hg) was not significantly lower than control group ( 65.5 ± 4. 8 mm Hg; F = 3.31, P = 0. 07 ). Children in intervention group showed more compliance. The patients' scores of the Ramsay scale, Briekopf and Buttner scale, Frankl scale, and Houpt scale in intervention group ( 1.37 ± 0. 96, 1.37 ± 0. 83, 1.32 ± 0. 67, and 2. 32 ± 1.49, respectively) were significantly lower than those in control group (3.71 ± 1.23, 2.71 ± 0. 96, 2.71 ± 0. 90, and 4.71 ± 1.19 ; F = 44. 66, 22. 36, 30.39,and 31.88,respectively,all P〈0.001) Conclusions Oral midazolam alone is safe and produces effective sedation for the dental treatment of young children. Oral midazolam application should be generally preferred because it is more easily accepted by pediatric patients.展开更多
Background: The aim was to evaluate the nonsurgical Root Canal Treatment (nRCT) outcome, the restorative condition and the relationship between the coronal restoration quality and the outcome of teeth endodontic treat...Background: The aim was to evaluate the nonsurgical Root Canal Treatment (nRCT) outcome, the restorative condition and the relationship between the coronal restoration quality and the outcome of teeth endodontic treated by undergraduates at the University of Caxias do Sul School of Dentistry (UCS-SD), Brazil, between 2019 and 2021. Materials and Methods: Data from the endodontically treated cases were retrieved, and the patients were recalled for a follow-up appointment at the university. The endodontic diagnosis, radiographs, and the presence of definitive restorations were analyzed in the clinical records. During the follow-up appointment, endodontically treated teeth were classified as present or absent. The nRCT was classified as successful (complete or incomplete healing) or failure (uncertain or unsatisfactory healing). Coronal restoration was classified as absent or present. When it was present, it was classified as permanent or temporary, and its quality as adequate or inadequate restoration. The results were presented as percentages. Results: A total of 257 teeth were endodontically treated. The most prevalent diagnosis was Chronic Apical Periodontitis (33.33%) and the most commonly treated teeth were premolars (46.15%). A total of 52 (21%) treated teeth were clinically and radiographically reexamined. The success rate for the nRCT was 98.08%. About 61.54% of this sample had a definitive composite resin restoration. Conclusion: The nRCT success rate was high. Special attention should be given to the presence and quality of the definitive restoration. Clinical Implications: There was no statistically significant impact between the coronal restoration and the nRCT success (P > 0.05).展开更多
Antibacterial dimethylaminododecyl methacrylate (DMADDM) was recently synthesized. The objectives of this study were to: (1) investigate antibacterial activity of DMADDM-containing primer on Streptococcus mutans ...Antibacterial dimethylaminododecyl methacrylate (DMADDM) was recently synthesized. The objectives of this study were to: (1) investigate antibacterial activity of DMADDM-containing primer on Streptococcus mutans impregnated into dentin blocks for the first time, and (2) compare the antibacterial efficacy of DMADDM with a previous quaternary ammonium dimethacrylate (QADM). Scotchbond Multi-Purpose (SBMP) bonding agent was used. DMADDM and QADM were mixed into SBMP primer. Six primers were tested: SBMP control primer P, P+2.5% DMADDM, P+5% DMADDM, P+7.5% DMADDM, P+10% DMADDM, and P+10% QADM. S. mutans were impregnated into human dentin blocks, and each primer was applied to dentin to test its ability to kill bacteria in dentinal tubules. Bacteria in dentin were collected via a sonication method, and the colony-forming units (CFU) and inhibition zones were measured. The bacterial inhibition zone of P+10% DMADDM was 10 times that of control primer (P〈0.05). CFU in dentin with P+10% DMADDM was reduced by three orders of magnitude, compared with control. DMADDM had a much stronger antibacterial effect than QADM, and antibacterial efficacy increased with increasing DMADDM concentration. Dentin shear bond strengths were similar among all groups (P〉0.1). In conclusion, antibacterial DMADDM-containing primer was validated to kill bacteria inside dentin blocks, possessing a much stronger antibacterial potency than the previous QADM. DMADDM-containing bonding agent was effective in eradicating bacteria in dentin, and its efficacy was directly proportional to DMADDM mass fraction. Therefore, DMADDM may be promisine for use in bonding agents as well as in other restorative and oreventive materials to inhibit bacteria.展开更多
Aim: The aim of this study was to evaluate the effects of different solutions on the flexural strength of one methacrylate-based resin and three bis-acryl resin provisional materials using an in vitro model test syste...Aim: The aim of this study was to evaluate the effects of different solutions on the flexural strength of one methacrylate-based resin and three bis-acryl resin provisional materials using an in vitro model test system. Methods: The specimens (25 × 2 × 2 mm) were prepared from interim materials and stored for 14 days at 37°C in different solutions (coffee, burn, cola) and distilled water (control group). A standard three-point bending test was conducted on the specimens with an Instron universal testing machine at crosshead speed of 0.5 mm/min. Data were analyzed using the one-way analysis of variance and Tukey HSD multiple comprasion tests. Results: The methacry-late-based resin (Takilon) showed the least fracture strength (61.6 - 85.6 MPa). One of the bis-acryl resins (Protemp 4-3M ESPE) showed the highest fracture strength (112 - 128 MPa). Conclusions: All bis-acryl resin composite materials exhibited high fracture strength over the traditional methyl methacrylate resin throughout the 14 day time interval of investigation. The different solutions have not statistically significant effect on the flexure strength values on four temporary materials.展开更多
基金The National High Technology Research and Development Program of China(863 Program)(No.2005AA420240)the Key Science and Technology Program of Jiangsu Province (No.BE2005014)
文摘According to the bio-characteristics of the lower and upper cavity surfaces of dental restoration, a stitching approach is proposed based on a virtual zipper working mechanism and a minimization of the surface total curvature energy, which is used to resolve the stitching problems existing during computer-aided design for dental restorations. First, the two boundaries corresponding to the lower and upper surfaces are triangulated based on the zipper working mechanism to generate the initial stitching surface patch, of which the edges are distributed uniformly between the boundaries. Secondly, the initial stitching surface patch is subdivided and deformed to reconstruct an optimized surface patch according to the bio-characteristics of the teeth. The optimized surface patch is minimally distinguishable from the surrounding mesh in smoothness and density, and it can stitch the upper and lower cavity surfaces naturally. The experimental results show that the dental restorations obtained by the proposed method can satisfy both the shape aesthetic and the fitting accuracy, and meet the requirements of clinical oral medicine.
基金supported by Open Fund of State Key Laboratory of Oral Diseases,Sichun University
文摘This paper aims to investigate if the dental restoration of nickel-chromium based alloy(Ni-Cr) leads to the enhanced excretions of Ni and Cr in urine.Seven hundred and ninety-five patients in a dental hospital had single or multiple Ni-Cr alloy restoration recently and 198 controls were recruited to collect information on dental restoration by questionnaire and clinical examination.Urinary concentrations of Ni and Cr from each subject were measure by graphite furnace atomic absorption spectrometry.Compared to the control group,the urinary level of Ni was significantly higher in the patient group of < 1 month of the restoration duration,among which higher Ni excretions were found in those with either a higher number of teeth replaced by dental alloys or a higher index of metal crown not covered with the porcelain.Urinary levels of Cr were significantly higher in the three patient groups of <1,1 to <3 and 3 to <6 months,especially in those with a higher metal crown exposure index.Linear curve estimations showed better relationships between urinary Ni and Cr in patients within 6-month groups.Our data suggested significant increased excretions of urinary Ni and Cr after dental restoration.Potential short- and long-term effects of Ni-Cr alloy restoration need to be investigated.
文摘Since the last two decades, restorative dentistry has been witnessing an increased acceptance of the use of the well-known all-ceramic materials for the fabrication of single dental restorations, such as inlays, onlays, crowns, anterior and posterior fixed partial dentures (PFPDs). These restorations certainly offer the potential for better biocompatibility coupled with superior aesthetic qualities, especially when compared with the conventional prostheses made from porcelain that is fused with metal ceramic restorations. However, brittleness and extreme sensitivity of all-ceramic materials to micro-like defects or cracks that are inherently present, or may grow, in their microstructure during different laboratory fabrication steps, during necessary clinical adjustments, or from post-placement chewing activity, remain major shortcomings of these dental restorations. In fact, many researchers are of the opinion that the improved mechanical properties can significantly improve the lifetime of all-ceramic restorations and result in enhanced reliability. Therefore, efforts of researchers, as well as manufacturers, have been directed towards the improvement of the mechanical properties in order to overcome such limitations. This article reviews the characterization of the most important mechanical properties that can delineate the behavior of all-ceramic dental materials upon loading. These include fracture mechanics, the brittle nature of ceramics, the relationship between microstructural features and fracture behavior, sources of cracks and flaws that may initiate a fracture and the effect of different fabrication procedures and/or clinical adjustments on the mechanical behavior of dental ceramics are also reviewed and discussed.
文摘<strong>Background:</strong> Diabetes increases periodontal disease risk and its complications, which are worsened with age or faulty restorations. <strong>Aim:</strong> Evaluate periodontal health among patients with diabetes treated with different dental restorations. <strong>Materials and Methods:</strong> This comparative cross-sectional study was conducted at the faculty of dentistry, Najran University, KSA, from March 2018 to February 2020. It included 260 diabetics, treated with different dental restorations, divided into four groups, each comprising 65 patients aged 45 - 60 years: Group 1 (G1), no restorations (control group);Group 2 (G2), Class II amalgam restorations;Group 3 (G3), Class II composite resin restorations;and Group 4 (G4), three-unit posterior metal ceramic prostheses. The Ages of all restorations ranged from 8 to 10 years. All groups were assessed for the Plaque Index (PI) and Gingival Index (GI), Overhangs Rate (OR), Alveolar Bone Loss (ABL) (the latter two using panoramic X-ray). HbA1c and duration of participants were also assessed and compared. <strong>Results:</strong> The mean HbA1c results of the groups ranged from 8.1% to 9.5%, and their mean diabetes durations ranged from 7.2 to 12 years. All the groups showed worse periodontal scores, ranging from 2.45 - 2.95 for PI and 2.25 - 2.8 for GI. G2 had higher scores than G1 and G3 (<em>p</em> < 0.001). G4 had the highest two recorded scores (<em>p</em> < 0.001). G2 had a higher rate of overhangs than G3 (<em>p</em> < 0.037). The mean ABL was 44% (SD 6.4) for G1, 56.0% (SD 6.7) for G2, 46.5% (SD 5.8) for G3, and 74.5% (SD 6.4) for G4. The lowest values were recorded in G1 and G3 (<em>p</em> = 0.987). The highest value was observed in G4, which was significantly higher than other groups (<em>p</em> < 0.001). <strong>Conclusion: </strong>The worse periodontal parameters among subjects treated with either three-unit metal ceramic or Class II amalgam restorations indicated severe periodontal destruction. Untreated subjects and subjects treated with Class II composite resin had relatively better periodontal status.
基金supported by the Shanghai Committee of Science and Technology,China(No.17441904100).
文摘The novel dental ceramics can be fabricated at lower temperatures when sol-gel derived lithium disilicate glass ceramics(LDGC)was used as an additive for yttria stabilized tetragonal zirconia polycrystalline(Y-TZP)ceramics.The effect of LDGC on the sintering,mechanical,and translucent properties of Y-TZP ceramics was investigated in the present study.The results showed that the LDGC additive effectively improved the densification of Y-TZP at 1100℃,which was much lower than the sintering temperature for pure Y-TZP.When sintered at 1100℃,the Y-TZP with 1 wt%LDGC reached a relative density of 95.45%,and prossessed a flexural strength of 482.4 MPa and a fracture toughness of 5.94 MPa-m12.Moreover,its translucency was also improved.While,the addition of LDGC could result in an escape of yttrium atoms from the grain lattice of zirconia,which induced the tetragonal-monoclinic transformation of zirconia and abnormal growth of monoclinic grains.The escaped yttrium atoms diffused into the intergranular glass phase.The results indicated that the novel Y-TZP-LDGC ceramics has a great potential to be used for all-ceramic restorations.
基金Beijing Municipal Science&Technology Commission(No of China.Z171100002017009)National Natural Science Foundation of China(Grant No.81671026)。
文摘Dental restorative materials with high mechanical properties and biocompatible performances are promising.In this work,polymer-infiltrated-ceramic-network materials(PICNs)were fabricated via infiltrating polymerizable monomers into porous ceramic networks and incorporated with hydroxyapatite nano-powders.Our results revealed that the flexural strength can be enhanced up to 157.32 MPa,and elastic modulus and Vickers hardness can be achieved up to 19.4 and 1.31 GPa,respectively,which are comparable with the commercial computer-aided design and computer-aided manufacturing(CAD/CAM)blocks.Additionally,the adhesion and spreading of rat bone marrow mesenchymal stem cells(r BMSCs)on the surface of such materials can be improved by adding hydroxyapatite,which results in good biocompatibility.Such PICNs are potential applicants for their application in the dental restoration.
文摘The wear rate of dental restoration materials on fixed, removable, and implant prostheses is important in the maintenance of cuspate form, masticatory efficiency and occlusal stability. Many permanent restoration materials such as composite, amalgam, gold, or porcelain show enough resistance to wear, but the wear rates of newly developed materials are generally unknown. To evaluate the wear rate of these dental materials, in vivo (clinic) and in vitro methods can be used. Since in vivo investigations are expensive, time consuming, and difficult to standardize, various in vitro methods have been developed. The use of a chewing machine is considered the best method, because a variety of wear mechanisms, temperature changes, and chemical effects of food and drink can be simulated simultaneously. This paper describes a dual axis chewing simulator for in vitro wear test of dental restoration materials. It consists of 8 test chambers, two stepper motors and related mechanism, a hot and cool water circle system, and a control unit. In the chambers, samples and antagonists make chewing movements vertically and Albert Ludwigs University, School of dentistry, Freiburg, Germany (Lü XY, Kern M and Strub JR) horizontally driven by the stepper motors so that the gnashing and slippage of two teeth against each other is simulated. A weighted test object is programmed to collide with a sample under precise operator control. The antagonists strike against the samples at various speeds from a slow nudge to snapping. Sample holders are designed for installation of varying samples, from single teeth to complete dentures. Two baths, six valves, and a group of pipes are used for the thermocycling. The machine can simulate various chewing modes in the mouth, including fully programmable thermal water cycling between 5℃ and 60℃ The control unit consists of a computer system with a built in specific program. Important operations such as “Start”, “Zero point”, and “Stop” are carried out by pressing the function keys on the front board of the unit. During the programming process and the simulation, several test modes and relevant test parameters are shown on the monitor. The control unit is connected via a series of interfaces to different controlled parts of the machine, such as the stepper motors and the pumps of cool and warm water.
基金the Review Committee of General Hospital of Central Theater Command(Approval No.05901).
文摘BACKGROUND Tooth defects can cause elongation of occlusal teeth,leading to insufficient repair space.The combination of dental implant restoration and orthodontic treatment of oblique adjacent teeth has a significant therapeutic effect.AIM To explore clinical efficacy,bone density,and follow-up of implant and orthodontic treatment for patients with inclined adjacent teeth.METHODS In total,98 patients with oblique adjacent teeth were randomly assigned to implant restoration combined with orthodontic treatment(group A,n=49)or to receive implant restoration alone(group B,n=49).Changes in alveolar ridge bone density and apical bone density were observed before and after treatment in the two groups.Changes in chewing function and language function were compared between the two groups of patients.Follow-up lasted for 12 mo after repair to observe any adverse reactions in the oral cavity.RESULTS The clinical effective rates of group A and group B were 97.96%and 85.71%,respectively,with group A having a higher clinical effective rate than group B.After treatment,the bone density of the alveolar ridge and apical bone in both groups decreased compared to before treatment,while the chewing and language functions improved.The changes in various indicators in group A were more significant.After treatment,the satisfaction rate of group A(97.96%)was higher than that of group B(79.59%).The incidence of adverse reactions in group A(2.04%)was lower than that in group B(24.49%).CONCLUSION The amalgamation of implant restoration and orthodontic treatment for adjacent tilted teeth demonstrates notable clinical efficacy,diminishes alveolar bone resorption,and fosters patient functional rehabilitation while exhibiting negligible adverse reactions.
文摘Objective To evaluate the effect of midazolam alone on sedation in young children for dental restorative care. Methods Forty children, aged 5 to 10 years with a mean age of 7.3 years, participated in this study. Twenty-one patients were assigned to intervention group received 0. 5 mg/kg of oral midazolam 20 minutes prior to the beginning of dental treatment, and 19 patients in control group received placebo liquid 20 minutes before treatment. All patients received painless local anesthetic injection and were restrained with children's board and bands. Blood pressure ( BP), heart rate (HR), oxygen saturation, treatment compliance scores of the Ramsay scale, the Briekopf and Butmer scale, Frankl scale, and the Houpt scale were recorded. Each procedure was taped and all the data were evaluated every 5 minutes by an anesthetist or experienced dentist who was unaware of the drug given to the child. Results HR in intervention group (82. 5 ± 5.1 bpm) was much lower than that in control group (95.2 ± 8.9 bpm; F=31.20, P 〈0. 001 ). Intervention group had a significantly lower systolic BP level (94.8±5.6 mmHg) than control group (98.5±5.5 mm Hg; F=4. 34, P =0. 04), but the diastolic BP (63.0 ± 3.5 mm Hg) was not significantly lower than control group ( 65.5 ± 4. 8 mm Hg; F = 3.31, P = 0. 07 ). Children in intervention group showed more compliance. The patients' scores of the Ramsay scale, Briekopf and Buttner scale, Frankl scale, and Houpt scale in intervention group ( 1.37 ± 0. 96, 1.37 ± 0. 83, 1.32 ± 0. 67, and 2. 32 ± 1.49, respectively) were significantly lower than those in control group (3.71 ± 1.23, 2.71 ± 0. 96, 2.71 ± 0. 90, and 4.71 ± 1.19 ; F = 44. 66, 22. 36, 30.39,and 31.88,respectively,all P〈0.001) Conclusions Oral midazolam alone is safe and produces effective sedation for the dental treatment of young children. Oral midazolam application should be generally preferred because it is more easily accepted by pediatric patients.
文摘Background: The aim was to evaluate the nonsurgical Root Canal Treatment (nRCT) outcome, the restorative condition and the relationship between the coronal restoration quality and the outcome of teeth endodontic treated by undergraduates at the University of Caxias do Sul School of Dentistry (UCS-SD), Brazil, between 2019 and 2021. Materials and Methods: Data from the endodontically treated cases were retrieved, and the patients were recalled for a follow-up appointment at the university. The endodontic diagnosis, radiographs, and the presence of definitive restorations were analyzed in the clinical records. During the follow-up appointment, endodontically treated teeth were classified as present or absent. The nRCT was classified as successful (complete or incomplete healing) or failure (uncertain or unsatisfactory healing). Coronal restoration was classified as absent or present. When it was present, it was classified as permanent or temporary, and its quality as adequate or inadequate restoration. The results were presented as percentages. Results: A total of 257 teeth were endodontically treated. The most prevalent diagnosis was Chronic Apical Periodontitis (33.33%) and the most commonly treated teeth were premolars (46.15%). A total of 52 (21%) treated teeth were clinically and radiographically reexamined. The success rate for the nRCT was 98.08%. About 61.54% of this sample had a definitive composite resin restoration. Conclusion: The nRCT success rate was high. Special attention should be given to the presence and quality of the definitive restoration. Clinical Implications: There was no statistically significant impact between the coronal restoration and the nRCT success (P > 0.05).
基金supported by NIH R01 DE17974 (Hockin HK Xu)a scholarship from West China School of Stomatology (Chen Chen)+3 种基金Program for New Century Excellent Talents in University (Lei Cheng)Youth Grant of Science and Technology Department of Sichuan Province China (2014JQ0033) (Lei Cheng)a bridge fund from University of Maryland Baltimore School of Dentistry (Hockin HK Xu)a seed grant from University of Maryland Baltimore (Hockin HK Xu)
文摘Antibacterial dimethylaminododecyl methacrylate (DMADDM) was recently synthesized. The objectives of this study were to: (1) investigate antibacterial activity of DMADDM-containing primer on Streptococcus mutans impregnated into dentin blocks for the first time, and (2) compare the antibacterial efficacy of DMADDM with a previous quaternary ammonium dimethacrylate (QADM). Scotchbond Multi-Purpose (SBMP) bonding agent was used. DMADDM and QADM were mixed into SBMP primer. Six primers were tested: SBMP control primer P, P+2.5% DMADDM, P+5% DMADDM, P+7.5% DMADDM, P+10% DMADDM, and P+10% QADM. S. mutans were impregnated into human dentin blocks, and each primer was applied to dentin to test its ability to kill bacteria in dentinal tubules. Bacteria in dentin were collected via a sonication method, and the colony-forming units (CFU) and inhibition zones were measured. The bacterial inhibition zone of P+10% DMADDM was 10 times that of control primer (P〈0.05). CFU in dentin with P+10% DMADDM was reduced by three orders of magnitude, compared with control. DMADDM had a much stronger antibacterial effect than QADM, and antibacterial efficacy increased with increasing DMADDM concentration. Dentin shear bond strengths were similar among all groups (P〉0.1). In conclusion, antibacterial DMADDM-containing primer was validated to kill bacteria inside dentin blocks, possessing a much stronger antibacterial potency than the previous QADM. DMADDM-containing bonding agent was effective in eradicating bacteria in dentin, and its efficacy was directly proportional to DMADDM mass fraction. Therefore, DMADDM may be promisine for use in bonding agents as well as in other restorative and oreventive materials to inhibit bacteria.
文摘Aim: The aim of this study was to evaluate the effects of different solutions on the flexural strength of one methacrylate-based resin and three bis-acryl resin provisional materials using an in vitro model test system. Methods: The specimens (25 × 2 × 2 mm) were prepared from interim materials and stored for 14 days at 37°C in different solutions (coffee, burn, cola) and distilled water (control group). A standard three-point bending test was conducted on the specimens with an Instron universal testing machine at crosshead speed of 0.5 mm/min. Data were analyzed using the one-way analysis of variance and Tukey HSD multiple comprasion tests. Results: The methacry-late-based resin (Takilon) showed the least fracture strength (61.6 - 85.6 MPa). One of the bis-acryl resins (Protemp 4-3M ESPE) showed the highest fracture strength (112 - 128 MPa). Conclusions: All bis-acryl resin composite materials exhibited high fracture strength over the traditional methyl methacrylate resin throughout the 14 day time interval of investigation. The different solutions have not statistically significant effect on the flexure strength values on four temporary materials.