Dielectric characteristics and nonlinear properties of ZnO-polypyrrole composites

The nonlinear properties and frequency characteristics of ZnO-polypyrrole composites were investigated at 200 Hz-5 MHz frequency interval with different zinc oxide contents. Samples were prepared using hot press method at 130 ℃. Results show an optimum point for breakdown voltage at ZnO content of 70%. Breakdown voltage decreases from 590 to 380 V and after that tends to increase from 450 to 740 V due to the absence of polypyrrole at grain boundaries. No matter how breakdown voltage behaves, nonlinear coefficient increases from 4.2 to 9 by increasing ZnO content because of the increase in acceptor-like states at grain boundaries by increasing ZnO content. The electrical parameters such as dielectric constant, dielectric loss and series resistance of samples show a strong dependence on frequency especially below 1 k Hz. These parameters fall off by increasing frequency up to 1 k Hz, which is related to charge transportation through the Schottky barrier at grain boundaries. The high dielectric constant of samples below 1 k Hz is related to the Maxwell-Wagner polarization at grain boundaries. The presence of different anomalies at different frequency intervals is related to interfacial polarization because of different structures of grains and intergranular layer with a huge difference in conductivity.

Dielectric Characteristics in BiFeO3-Modified SrTiO3 Incipient Ferroelectric Ceramics

We investigate the dielectric and ferroelectric properties of Sr1-xBixTi1-xFex03 solid solutions （x =0, 0.05, 0.1, 0.15 and 0.2） together with their structures. Through the analysis of Rietveld refinement of powder x-ray diffraction, a cubic structure in space group Pm3m is determined for all the compositions. An obvious dielectric relaxation peak differing from SrTiO3 is observed in the present ceramics. The peak temperature Tm increases with increasing x, and it approaches room temperature at x =0.2. The Vogel Fulcher law and Curie Weiss law fittings further confirm the relaxor ferroelectricity in the present ceramics.

Effect of oxygen content on dielectric characteristics of Cr-doped LaTiO_(x)

The ceramics La_(0.85)Cr_(0.15)TiO_(x)and La_(0.7)Cr_(0.3)TiO_(x)are prepared by conventional solid-state reaction method.The dielectric properties of Cr-doped La TiO_(x)as a function of frequency(0.1 k Hz≤f≤1 MHz)and temperature(77 K≤T≤360 K)are studied.The blocks are then annealed in a flowing O2 or Ar/H_(2)to convert their oxygen content and the tests mentioned above are performed.The highly oxygenated samples exhibit extremely high low-frequency dielectric constants at room temperature(~10^(6)).The results show that the oxygen stoichiometry could significantly influence the dielectric properties of Cr-doped LaTiO_(x).

Dielectric and Pyroelectric Characteristics of the Infrared Sensitive (Pb_(1-x)Sr_x)TiO_3 Ceramics

PST ferroelectric ceramics were fabricated successfully by a two-step method, i e first, PbTiO3 and SrTiO3 were sintered respectively, then mixed and sintered together. The process and characteristics of PST ferroelectric ceramics were introduced and researched. Their dielectric and pyroelectric characteristics are as follows dielectric constant 10^4 order, low dielectric loss （lower than 3.0% in the working frequency range of 1-1 000 kHz）, saturation polarization intensity 10^-1 C/m^2 order, and pyroelectric coefficient 10^-3 C/m^2·K order.

Low-firing and temperature stability regulation of tri-rutile MgTa_(2)O_(6)microwave dielectric ceramics

A glass frit containing Li_(2)O-MgO-ZnO-B_(2)O_(3)-SiO_(2)component was used to explore the low-temperature sintering behaviors and microwave dielectric characteristics of tri-rutile MgTa_(2)O_(6)ceramics in this study.The good low-firing effects are presented due to the high matching relevance between Li_(2)O-MgO-ZnO-B_(2)O_(3)-SiO_(2)glass and MgTa_(2)O_(6)ceramics.The pure tri-rutile MgTa_(2)O_(6)structure remains unchanged,and high sintering compactness can also be achieved at 1150℃.We found that the Li_(2)O-MgO-ZnO-B_(2)O_(3)-SiO_(2)glass not only greatly improves the low-temperature sintering characteristics of MgTa_(2)O_(6)ceramics but also maintains a high(quality factor(Q)×resonance frequency(f))value while still improving the temperature stability.Typically,great microwave dielectric characteristics when added with 2wt%Li_(2)O-MgO-ZnO-B_(2)O_(3)-SiO_(2)glass can be achieved at 1150℃:dielectric constant,ε_(r)=26.1;Q×f=34267 GHz;temperature coefficient of resonance frequency,τ_(f)=-8.7×10^(-6)/℃.

Study on the Mathematical Model of Dielectric Recovery Characteristics in High Voltage SF6 Circuit Breaker

According to the stream theory, this paper proposes a mathematical model of the dielectric recovery characteristic based on the two-temperature ionization equilibrium equation. Taking the dynamic variation of charged particle＇s ionization and attachment into account, this model can be used in collaboration with the Coulomb collision model, which gives the relationship of the heavy particle temperature and electron temperature to calculate the electron density and temperature under different pressure and electric field conditions, so as to deliver the breakdown electric field strength under different pressure conditions. Meanwhile an experiment loop of the circuit breaker has been built to measure the breakdown voltage. It is shown that calculated results are in conformity with experiment results on the whole while results based on the stream criterion are larger than experiment results. This indicates that the mathematical model proposed here is more accurate for calculating the dielectric recovery characteristic, it is derived from the stream model with some improvement and refinement and has great significance for increasing the simulation accuracy of circuit breaker＇s interruption characteristic.

The Characteristics of Dielectric Barrier Discharge and its Influence on the Excimer XeCl Emission

In this work, the influence of discharge modes on the excimer XeCl emission (308 nm) has been studied by adding helium gas into the xenon and chlorine mixture. It is found that the transition from filament discharge to glow /filament - combined discharge leads to the decrease in excimer emission. We are the first one to use a flowing water film as an outer transparent electrode, and achieve a higher UV intensity, compared with the case by using a metal mesh as the outer electrode. The influence of the gas temperature both in the reactor Tg and in a discharge channel Tc on the excimer emission has been analyzed preliminarily. Finally, it has been expected that the replacement of chlorine gas Cl2 by another chlorine gas may reduce the heat generated in the discharge processes and give rise to the excimer XeCl* radiation.

Radio-Frequency Characteristics of Partial Dielectric Removal HR-SOI and TR-SOI Substrates

High-resistivity silicon-on-insulator （HR-SOI） and trap-rich high-resistivity silicon-on-insulator （TR-S01） sub- strates have been widely adopted for high-performance rf integrated circuits. Radio-frequency loss and non- linearity characteristics are measured from coplanar waveguide （CPW） t lines fabricated on HR-SOI and TR-SOI substrates. The patterned insulator structure is introduced to reduce loss and non-linearity char- acteristics. A metal-oxide-semiconductor （MOS） CPW circuit model is established to expound the mechanism of reducing the parasitic surface conductance （PSC） effect by combining the semiconductor characteristic anal- ysis （pseudo-MOS and C-V test）. The rf performance of the CPW transmission lines under dc bias supply is also compared. The TR-SOI substrate with the patterned oxide structure sample has the minimum rf loss （〈0.2 dB/mm up to 10 GHz）, the best non-linearity performance, and reductions of 4 dB and 10 dB are compared with the state-of-the-art TR-SOI sample＇s, HD2 and HD3, respectively. It shows the potential application for integrating the two schemes to further suppress the PSC effect.

Electric characteristics of Nd_2O_3 doped BaTiO_3 ceramics

Nd2O3 doped BaTiO3ceramics（the additive content was respectively 0.001, 0.002, 0.003, 0.005, 0.01 molar ratio）were prepared by Sol-Gel method to study their dielectric characteristics and electric conductivities through X-ray photoelectron spectrum （XPS）. The results showed that the dielectric characteristics of Nd2O3 doped BaTiO3 ceramics were improved by doping. When Nd2O3 content was 0.003 mol, the results were even better, the dielectric constant was increased, the dielectric loss was decreased, the Curie-temperature （Tc） was 110 ℃, and the frequency characteristic was also good. The resistivity of Nd2O3 doped BaTiO3 ceramics was lower than that of pure BaTiO3 ceramics, when Nd2O3 content was 0.001 mol,the resistivity was （2.364×）108 Ω·m, the smallest. The grain resistance of Nd2O3 doped BaTiO3 ceramics exhibited NTC effect, but the grain boundary resistance showed PTC effect, and the grain boundary resistance was larger than that of the grain resistance, so the PTC effect originated from the grain boundary. The analysis of the element binding energy through X-ray photoelectron spectrum were indicated that the quantivalence of Ba2+and Ti4+in Nd2O3 doped BaTiO3 ceramics was variable, and resulted in the improvement of the conductibility of BaTiO3 ceramics.

Study on BaO-Sm_2O_3-TiO_2 Microwave Dielectric Ceramics Doped with Bismuth and Zinc

BaO-Sm2O3-TiO2 microwave dielectric ceramics doped with Bi and Zn was studied. The experiment was based on BST microwave dielectric ceramics doped with Bi2O3, which is shown by Ba4(Sm1-yBiy )28/3Ti18O54. When y =0.15, ZnO was added and the effects of ZnO on this system were studied. The result shows that the dielectric characteristics of BST microwave dielectric ceramics are the most excellent when the content of ZnO is 3% , and the optimal sintering temperature is 1200℃.

Discharge Modes Suggested by Emission Spectra of Nitrogen Dielectric Barrier Discharge with Wire-Cylinder Electrodes

In this paper,nitrogen dielectric barrier discharge（DBD） plasma was generated in a quartz tube with coaxial wire-cylinder electrodes at atmospheric pressure.By varying the nitrogen gas flow（FN） in the range of 0-1 m3/h,the plasma optical emission spectra（OES） were measured and studied.The vibration（T_（vib）） and rotation temperature（T_（rot）） of nitrogen were obtained,by fitting the rovibronic bands of N_2（C^3∏_u-B^3∏_g,0-1）,and by the Boltzmann plot method for purposes of comparison.T_（vib） increased up to 2481 K with increasing nitrogen flow till0.2 m3/h,and then decreased with further increasing FN,while Trot decreased monotonously and approached to-350 K for FN ≥ 0.6 m^3/h.The intensity of N_2（C^3∏_u-B^3∏_g,0-0,1-0,0-3） and N_2~＋（B^2∑_u~＋-X^2Σ_g~＋,0-0） exhibited similar evolution with increasing FN to those of the T_（vib） and Trot,respectively.The discharge photos revealed that the discharge filaments gradually decreased with increasing FN,and eventually disappeared,which implied that a discharge mode transition emerged with increasing FN.The possible mechanism for the discharge mode transition is studied in detail according to the vibration（T_（vib）） and rotation temperature（T_（rot）） of nitrogen.

Effect of sintering temperature on microstructure and varistor properties of Zn-V-O-based ceramics incorporated with Mn-Nb-Tb

The effect of sintering temperature on microstructure and varistor properties of Zn-V-O-based ceramics incorporated with Mn-Nb-Tb was investigated. The results showed that the increase of sintering temperature in the range from 875 to 950 °C decreased the densities of sintered pellets in the range of 5.55 to 5.45 g/cm3 and increased the average grain size in the range of 4.1 to 8.8 ？m. The breakdown field decreased noticeably from 7443 to 1064 V/cm with increasing sintering temperature from 875 to 950 °C. The varistor ceramics sintered at 900 ？C exhibited nonlinear properties, with 49.4 in the nonlinear coefficient and 0.21 m A/cm2 in the leakage current density. The dielectric constant increased greatly from 440.1 to 2197.2 with increasing sintering temperature from 875 to 950 °C; however, the dissipation factor exhibited a fluctuation between 0.237 and 0.5. These ceramic compositions and sintering conditions can be applied to the development of advanced multiplayer varistors with silver as an inner electrode.

Sensors for control of water transparency in optical and microwave ranges

In the face of deteriorating environmental conditions in the world,water quality control is an urgent task.It can be solved by creating sensors with high accuracy and low cost,which requires the development of fundamentally new radiophysical methods that take advantage of the optical,microwave and millimeter wavelengths that have a significantly greater sensitivity to low concentrations of pollutants and a lower inertia.The article presents prototypes of measuring cells of the microwave and optical ranges as well as the results of an experimental study of water of various degrees of pollution with their help.The results show that the use of the highly sensitive method of capillary-waveguide resonance makes it possible to detect the presence of micro impurities in water with concentrations up to0.1%and to identify water even from sources of various natural origins.In addition,the use of measurements at several frequencies in the optical range will make it possible to solve the problem of creating water control sensors with high sensitivity to pollution and low cost.It can be concluded that the possibility of complex use of multiwave sensors(optical,infrared and microwave ranges)allows to increase the sensitivity and reliability of water quality assessment.

Exploring dielectric phenomena in sulflower-like nanostructures via Monte Carlo technique

This research focuses on the electric behavior of a mixed ferrielectric sulflower-like nanostructure.The structure includes a core with spin S_(i)^(Z)-1 atoms and a shell with spin σ_(j)^(Z)-5/2 atoms.The Blume–Capel model and the Monte Carlo technique(MCt)with the Metropolis algorithm are employed.Diagrams are established for absolute zero,investigating stable spin configurations correlated with various physical parameters.The MCt method explores phase transition behavior and electric hysteresis cycles under different physical parameters.

Improved Breakdown Strength in(Ba_(0.6)Sr_(0.4))_(0.85)Bi_(0.1)TiO_3 Ceramics with Addition of CaZrO_3 for Energy Storage Application

（Ba（0.6） Sr（0.4））（0.85） Bi（0.1） TiO3 ceramics doped with x wt%CaZrO3（x= 0-10） were synthesized by solid-state reaction method. The effects of CaZrO3 amount on the dielectric properties and structure of（Ba（0.6）Sr（0.4））（0.85） Bi（0.1） TiO3 ceramics were investigated. X-ray diffraction results indicated a pure cubic perovskite structure for all samples and that the lattice parameter increased till x=5 and then slightly decreased. A homogenous microstructure was observed with the addition of CaZrO3. Dielectric measurements revealed a relaxor-like characteristic for all samples and that the diffusivity γ reached the maximum value of 1.78 at x=5. With the addition of CaZrO3, the dielectric constant dependence on electric field was weakened, insulation resistivity enhanced and dielectric breakdown strength improved obviously and reached 19.9 k V/mm at x=7.5. In virtue of low dielectric loss（tan d〈0.001 5）, moderate dielectric constant（er 〉1 500） and high breakdown strength（Eb 〉17.5 k V/mm）, the CaZrO3 doped（Ba（0.6）Sr（0.4））0.85 Bi（0.1） TiO3 ceramic is a potential candidate material for high power electric applications.

Domain structure and dielectric diffusion-relaxation characteristics of ternary Pb(In_(1/2)Nb_(1/2))O_(3)-Pb(Mg_(1/3)Nb_(2/3))O_(3)-PbTiO_(3)ceramics

Relaxor-based ternary Pb(In1/2Nb1/2)O_(3)-Pb(Mg_(1/3)Nb_(2/3))O_(3)-PbTiO_(3)(PIN-PMN-PT)single crystals and ceramics are promis­ing candidates for high-performance electromechanical conversion devices.It is known that the domain structure and dielectric diffusion-relaxation characteristics are crucial to the excellent performances of relaxor ferroelectrics.In this work,we prepared the PIN-PMN-PT ceramics with various PIN/PMN proportions and systematically investigated their domain structure and dielec­tric diffusion-relaxation properties.The effect of PIN/PMN proportion on the domain size and dielectric diffusion-relaxation characteristics was also studied.The investigations showed that PIN-PMN-PT ceramics presented multi-type domain patterns comprising irregular island domains and regular lamellar domains.Moreover,the dependent relations of PIN/PMN proportions on the dielectric diffusion and domain size indicated that the PIN composition has a stronger lattice distortion than PMN composi­tion;increasing the PIN proportion can enhance the dielectric diffusion and decrease the domain size.Our results could deepen the understanding of structure-property relationships of multicomponent relaxor ferroelectrics and guide the design and exploration of new high-performance ferroelectric materials.