Hydrocarbon distribution rules in the deep and shallow parts of sedimentary basins are considerably different, particularly in the following four aspects. First, the critical porosity for hydrocarbon migration is much...Hydrocarbon distribution rules in the deep and shallow parts of sedimentary basins are considerably different, particularly in the following four aspects. First, the critical porosity for hydrocarbon migration is much lower in the deep parts of basins: at a depth of 7000 m, hydrocarbons can accumulate only in rocks with porosity less than 5%. However, in the shallow parts of basins (i.e., depths of around 1000 m), hydrocarbon can accumulate in rocks only when porosity is over 20%. Second, hydrocarbon reservoirs tend to exhibit negative pressures after hydrocarbon accumulation at depth, with a pressure coefficient less than 0.7. However, hydrocarbon reservoirs at shallow depths tend to exhibit high pressure after hydrocarbon accumulation. Third, deep reservoirs tend to exhibit characteristics of oil (-gas)-water inversion, indicating that the oil (gas) accumulated under the water. However, the oil (gas) tends to accumulate over water in shallow reservoirs. Fourth, continuous unconventional tight hydrocarbon reservoirs are distributed widely in deep reservoirs, where the buoyancy force is not the primary dynamic force and the caprock is not involved during the process of hydrocarbon accumulation. Conversely, the majority of hydrocarbons in shallow regions accumulate in traps with complex structures. The results of this study indicate that two dynamic boundary conditions are primarily responsible for the above phenomena: a lower limit to the buoyancy force and the lower limit of hydrocarbon accumulation overall, corresponding to about 10%-12% porosity and irreducible water saturation of 100%, respectively. These two dynamic boundary conditions were used to divide sedimentary basins into three different dynamic fields of hydrocarbon accumulation: the free fluid dynamic field, limit fluid dynamic field, and restrain fluid dynamic field. The free fluid dynamic field is located between the surface and the lower limit of the buoyancy force, such that hydrocarbons in this field migrate and accumulate under the influence of, for example, the buoyancy force, pressure, hydrodynamic force, and capillary force. The hydrocarbon reservoirs formed are characterized as "four high," indicating that they accumulate in high structures, are sealed in high locations, migrate into areas of high porosity, and are stored in reservoirs at high pressure. The basic features of distribution and accumulation in this case include hydrocarbon migration as a result of the buoyancy force and formation of a reservoir by a caprock. The limit fluid dynamic field is located between the lower limit of the buoyancy force and the lower limit of hydrocarbon accumulation overall; the hydrocarbon migrates and accumulates as a result of, for example, the molecular expansion force and the capillary force. The hydrocarbon reservoirs formed are characterized as "four low," indicating that hydrocarbons accumulate in low structures, migrate into areas of low porosity, and accumulate in reservoirs with low pressure, and that oil(-gas)-water inversion occurs at low locations. Continuous hydrocarbon accumulation over a large area is a basic feature of this field. The restrain fluid dynamic field is located under the bottom of hydrocarbon accumulation, such that the entire pore space is filled with water. Hydrocarbons migrate as a result of the molecular diffusion force only. This field lacks many of the basic conditions required for formation of hydrocarbon reservoirs: there is no effective porosity, movable fluid, or hydrocarbon accumulation, and potential for hydrocarbon exploration is low. Many conventional hydrocarbon resources have been discovered and exploited in the free fluid dynamic field of shallow reservoirs, where exploration potential was previously considered to be low. Continuous unconventional tight hydrocarbon resources have been discovered in the limit fluid dynamic field of deep reservoirs; the exploration potential of this setting is thought to be tremendous, indicating that future exploration should be focused primarily in this direction.展开更多
Puhe Coal Mine is a typical Tertiary coal in Shenbei mining area. With an increase in mining depth, tectonic stress field becomes more complex, leading to increased deformation and failure of the soft rock roadway. St...Puhe Coal Mine is a typical Tertiary coal in Shenbei mining area. With an increase in mining depth, tectonic stress field becomes more complex, leading to increased deformation and failure of the soft rock roadway. Stress becomes an important factor of mine safety and stability. This paper analyzes the distribution of the regional tectonic field, and determines the distribution of situ stress measurement through measuring the ground stress field in the main mining area level of Puhe Coal Mine using stress relief method. The acquired in situ stress data at different locations and depths provide a reference for the rational arrangement of the stop and mine roadway supporting design, which are of great significance for the efficient safety production of the mine.展开更多
Artificial intelligence plays an essential role in the medical and health industries.Deep convolution networks offer valuable services and help create automated systems to perform medical image analysis.However,convol...Artificial intelligence plays an essential role in the medical and health industries.Deep convolution networks offer valuable services and help create automated systems to perform medical image analysis.However,convolution networks examine medical images effectively;such systems require high computational complexity when recognizing the same disease-affected region.Therefore,an optimized deep convolution network is utilized for analyzing disease-affected regions in this work.Different disease-relatedmedical images are selected and examined pixel by pixel;this analysis uses the gray wolf optimized deep learning network.This method identifies affected pixels by the gray wolf hunting process.The convolution network uses an automatic learning function that predicts the disease affected by previous imaging analysis.The optimized algorithm-based selected regions are further examined using the distribution pattern-matching rule.The pattern-matching process recognizes the disease effectively,and the system’s efficiency is evaluated using theMATLAB implementation process.This process ensures high accuracy of up to 99.02%to 99.37%and reduces computational complexity.展开更多
Thermophysical parameters are the main parameters affecting the utilization efficiency of shallow geothermal energy. Based on the research and evaluation data of shallow geothermal energy in capital cities of China, t...Thermophysical parameters are the main parameters affecting the utilization efficiency of shallow geothermal energy. Based on the research and evaluation data of shallow geothermal energy in capital cities of China, this paper analyzes the differences between two testing methods and finds that data measured in in-situ thermal conductivity test is closer to the actual utilization. This paper analyzes the influencing factors of thermophysical parameters from lithology, density, moisture content and porosity: The thermal conductivity coefficient of bedrock is generally higher than Quaternary system loose bed soil; as for the coefficient of bedrock, dolomite, shale and granite are higher while gabbro, sandstone and mudstone are lower; as for the coefficient of loose bed, pebble and gravel are higher while clay and silt are lower. As the particle size of sand decreases, the thermal conductivity coefficient declines accordingly. The thermal conductivity coefficient increases linearly with growing density and decreases in logarithm with growing moisture content as well as porosity; specific heat capacity decreases in logarithm with growing density, increases in power exponent with growing moisture content and decreases linearly with growing porosity. The thermal conductivity coefficient is high when hydrodynamic condition is good and vice versa. The conclusions of this paper have guiding significance for the research, evaluation and development of shallow geothermal energy in other areas.展开更多
The microstructure distribution rule of semi-solid AZ91D alloy treated by ultrasonic was researched, and mechanical properies of specimens before and after ultrasonic treatment were investigated further.Semi-solid AZ9...The microstructure distribution rule of semi-solid AZ91D alloy treated by ultrasonic was researched, and mechanical properies of specimens before and after ultrasonic treatment were investigated further.Semi-solid AZ91D melt specimens were processed by ultrasonic under different powers, and its microstructures and mechanical properties at different sampling points in specimens were obtained. The experimental results show that the microstructure of AZ91D alloy at different sampling points under the same ultrasonic power is different in grain size and shape, and there is also great difference among their microstructures at the same sampling point under different ultrasonic powers. AZ91D alloy treated by ultrasonic can obtain increment in both tensile strength and plasticity. Under same ultrasonic power, mechanical properties of specimen at different sampling points have obvious difference, and regularity for change of mechanical properties everywhere is similar to regularity for change of grain size and shape everywhere.展开更多
This paper studied the basic properties of saline soil at different depths of a sampling site in Da'an, China, through field reconnaissance and laboratory analysis. A series of experiments which comprised the analyse...This paper studied the basic properties of saline soil at different depths of a sampling site in Da'an, China, through field reconnaissance and laboratory analysis. A series of experiments which comprised the analyses of grain size distribution, mineral composition, soil physical properties, soluble salt concent, pH, organic content and cation exchange capacity were conducted. Through these experiments, the distribution rule of each property and their causes are discussed. These results could provide a fundamental base for the study of moisture migration.展开更多
Association rule mining is an important issue in data mining. The paper proposed an binary system based method to generate candidate frequent itemsets and corresponding supporting counts efficiently, which needs only ...Association rule mining is an important issue in data mining. The paper proposed an binary system based method to generate candidate frequent itemsets and corresponding supporting counts efficiently, which needs only some operations such as "and", "or" and "xor". Applying this idea in the existed distributed association rule mining al gorithm FDM, the improved algorithm BFDM is proposed. The theoretical analysis and experiment testify that BFDM is effective and efficient.展开更多
Controllers play a critical role in software-defined networking(SDN).However,existing singlecontroller SDN architectures are vulnerable to single-point failures,where a controller's capacity can be saturated by fl...Controllers play a critical role in software-defined networking(SDN).However,existing singlecontroller SDN architectures are vulnerable to single-point failures,where a controller's capacity can be saturated by flooded flow requests.In addition,due to the complicated interactions between applications and controllers,the flow setup latency is relatively large.To address the above security and performance issues of current SDN controllers,we propose distributed rule store(DRS),a new multi-controller architecture for SDNs.In DRS,the controller caches the flow rules calculated by applications,and distributes these rules to multiple controller instances.Each controller instance holds only a subset of all rules,and periodically checks the consistency of flow rules with each other.Requests from switches are distributed among multiple controllers,in order to mitigate controller capacity saturation attack.At the same time,when rules at one controller are maliciously modified,they can be detected and recovered in time.We implement DRS based on Floodlight and evaluate it with extensive emulation.The results show that DRS can effectively maintain a consistently distributed rule store,and at the same time can achieve a shorter flow setup time and a higher processing throughput,compared with ONOS and Floodlight.展开更多
Sucrose is the main constituent of assimilation transport from source to sink.In order to study the transport mechanism of sucrose,the sucrose at stem was taken as a research object and the sucrose flow field in tomat...Sucrose is the main constituent of assimilation transport from source to sink.In order to study the transport mechanism of sucrose,the sucrose at stem was taken as a research object and the sucrose flow field in tomato stem was analyzed using CFD ANSYS FLUENT simulation.The results showed that the sucrose pressure distribution was lower at bottom node and higher at middle node.The velocity of sucrose at different nodes was higher at the bottom node and lower at middle node and assimilation flow direction of the first,second,and third leaf from the bottom was towards the roots.The result of verification experiment showed that sucrose content measured at different nodes was higher at middle node than that of bottom node.Results of this study confirmed that ANASYS FLUENT can better simulate sucrose migration in greenhouse tomato stem.This study provides a new method for studying the partitioning mechanism of tomato assimilates in greenhouse.展开更多
基金supported by the National Basic Research Program of China (Grant No: 2011CB201100)
文摘Hydrocarbon distribution rules in the deep and shallow parts of sedimentary basins are considerably different, particularly in the following four aspects. First, the critical porosity for hydrocarbon migration is much lower in the deep parts of basins: at a depth of 7000 m, hydrocarbons can accumulate only in rocks with porosity less than 5%. However, in the shallow parts of basins (i.e., depths of around 1000 m), hydrocarbon can accumulate in rocks only when porosity is over 20%. Second, hydrocarbon reservoirs tend to exhibit negative pressures after hydrocarbon accumulation at depth, with a pressure coefficient less than 0.7. However, hydrocarbon reservoirs at shallow depths tend to exhibit high pressure after hydrocarbon accumulation. Third, deep reservoirs tend to exhibit characteristics of oil (-gas)-water inversion, indicating that the oil (gas) accumulated under the water. However, the oil (gas) tends to accumulate over water in shallow reservoirs. Fourth, continuous unconventional tight hydrocarbon reservoirs are distributed widely in deep reservoirs, where the buoyancy force is not the primary dynamic force and the caprock is not involved during the process of hydrocarbon accumulation. Conversely, the majority of hydrocarbons in shallow regions accumulate in traps with complex structures. The results of this study indicate that two dynamic boundary conditions are primarily responsible for the above phenomena: a lower limit to the buoyancy force and the lower limit of hydrocarbon accumulation overall, corresponding to about 10%-12% porosity and irreducible water saturation of 100%, respectively. These two dynamic boundary conditions were used to divide sedimentary basins into three different dynamic fields of hydrocarbon accumulation: the free fluid dynamic field, limit fluid dynamic field, and restrain fluid dynamic field. The free fluid dynamic field is located between the surface and the lower limit of the buoyancy force, such that hydrocarbons in this field migrate and accumulate under the influence of, for example, the buoyancy force, pressure, hydrodynamic force, and capillary force. The hydrocarbon reservoirs formed are characterized as "four high," indicating that they accumulate in high structures, are sealed in high locations, migrate into areas of high porosity, and are stored in reservoirs at high pressure. The basic features of distribution and accumulation in this case include hydrocarbon migration as a result of the buoyancy force and formation of a reservoir by a caprock. The limit fluid dynamic field is located between the lower limit of the buoyancy force and the lower limit of hydrocarbon accumulation overall; the hydrocarbon migrates and accumulates as a result of, for example, the molecular expansion force and the capillary force. The hydrocarbon reservoirs formed are characterized as "four low," indicating that hydrocarbons accumulate in low structures, migrate into areas of low porosity, and accumulate in reservoirs with low pressure, and that oil(-gas)-water inversion occurs at low locations. Continuous hydrocarbon accumulation over a large area is a basic feature of this field. The restrain fluid dynamic field is located under the bottom of hydrocarbon accumulation, such that the entire pore space is filled with water. Hydrocarbons migrate as a result of the molecular diffusion force only. This field lacks many of the basic conditions required for formation of hydrocarbon reservoirs: there is no effective porosity, movable fluid, or hydrocarbon accumulation, and potential for hydrocarbon exploration is low. Many conventional hydrocarbon resources have been discovered and exploited in the free fluid dynamic field of shallow reservoirs, where exploration potential was previously considered to be low. Continuous unconventional tight hydrocarbon resources have been discovered in the limit fluid dynamic field of deep reservoirs; the exploration potential of this setting is thought to be tremendous, indicating that future exploration should be focused primarily in this direction.
基金supported by the National Natural Science Foundation of China (No. 41040027)the Central University Basic Research Fund (No. 2009QL06)
文摘Puhe Coal Mine is a typical Tertiary coal in Shenbei mining area. With an increase in mining depth, tectonic stress field becomes more complex, leading to increased deformation and failure of the soft rock roadway. Stress becomes an important factor of mine safety and stability. This paper analyzes the distribution of the regional tectonic field, and determines the distribution of situ stress measurement through measuring the ground stress field in the main mining area level of Puhe Coal Mine using stress relief method. The acquired in situ stress data at different locations and depths provide a reference for the rational arrangement of the stop and mine roadway supporting design, which are of great significance for the efficient safety production of the mine.
文摘Artificial intelligence plays an essential role in the medical and health industries.Deep convolution networks offer valuable services and help create automated systems to perform medical image analysis.However,convolution networks examine medical images effectively;such systems require high computational complexity when recognizing the same disease-affected region.Therefore,an optimized deep convolution network is utilized for analyzing disease-affected regions in this work.Different disease-relatedmedical images are selected and examined pixel by pixel;this analysis uses the gray wolf optimized deep learning network.This method identifies affected pixels by the gray wolf hunting process.The convolution network uses an automatic learning function that predicts the disease affected by previous imaging analysis.The optimized algorithm-based selected regions are further examined using the distribution pattern-matching rule.The pattern-matching process recognizes the disease effectively,and the system’s efficiency is evaluated using theMATLAB implementation process.This process ensures high accuracy of up to 99.02%to 99.37%and reduces computational complexity.
基金supported by Development and Use of Shallow Part Geothermal Energy below the Earth Surface and Research on Geothermal Reinjection Technology, the Basic Research Funding Project (SK201501)
文摘Thermophysical parameters are the main parameters affecting the utilization efficiency of shallow geothermal energy. Based on the research and evaluation data of shallow geothermal energy in capital cities of China, this paper analyzes the differences between two testing methods and finds that data measured in in-situ thermal conductivity test is closer to the actual utilization. This paper analyzes the influencing factors of thermophysical parameters from lithology, density, moisture content and porosity: The thermal conductivity coefficient of bedrock is generally higher than Quaternary system loose bed soil; as for the coefficient of bedrock, dolomite, shale and granite are higher while gabbro, sandstone and mudstone are lower; as for the coefficient of loose bed, pebble and gravel are higher while clay and silt are lower. As the particle size of sand decreases, the thermal conductivity coefficient declines accordingly. The thermal conductivity coefficient increases linearly with growing density and decreases in logarithm with growing moisture content as well as porosity; specific heat capacity decreases in logarithm with growing density, increases in power exponent with growing moisture content and decreases linearly with growing porosity. The thermal conductivity coefficient is high when hydrodynamic condition is good and vice versa. The conclusions of this paper have guiding significance for the research, evaluation and development of shallow geothermal energy in other areas.
基金Funded by the National Science Foundation of China(50465003)the Project Funded by Science and Technology Department of Jiangxi Province,China(20061B0102200)
文摘The microstructure distribution rule of semi-solid AZ91D alloy treated by ultrasonic was researched, and mechanical properies of specimens before and after ultrasonic treatment were investigated further.Semi-solid AZ91D melt specimens were processed by ultrasonic under different powers, and its microstructures and mechanical properties at different sampling points in specimens were obtained. The experimental results show that the microstructure of AZ91D alloy at different sampling points under the same ultrasonic power is different in grain size and shape, and there is also great difference among their microstructures at the same sampling point under different ultrasonic powers. AZ91D alloy treated by ultrasonic can obtain increment in both tensile strength and plasticity. Under same ultrasonic power, mechanical properties of specimen at different sampling points have obvious difference, and regularity for change of mechanical properties everywhere is similar to regularity for change of grain size and shape everywhere.
基金supported by the National Natural Science Foundation of China(Nos.41430642 and 41372267)the Research Fund for the Doctoral Program of Higher Education of China(No.20120061110054)
文摘This paper studied the basic properties of saline soil at different depths of a sampling site in Da'an, China, through field reconnaissance and laboratory analysis. A series of experiments which comprised the analyses of grain size distribution, mineral composition, soil physical properties, soluble salt concent, pH, organic content and cation exchange capacity were conducted. Through these experiments, the distribution rule of each property and their causes are discussed. These results could provide a fundamental base for the study of moisture migration.
基金Supported by the National Natural Science Foun-dation of China (70371015)
文摘Association rule mining is an important issue in data mining. The paper proposed an binary system based method to generate candidate frequent itemsets and corresponding supporting counts efficiently, which needs only some operations such as "and", "or" and "xor". Applying this idea in the existed distributed association rule mining al gorithm FDM, the improved algorithm BFDM is proposed. The theoretical analysis and experiment testify that BFDM is effective and efficient.
基金supported by the National Natural Science Foundation of China(Nos.61402357,61272459,and 61402357)the China Postdoctoral Science Foundation(No.2015M570835)+2 种基金the Fundamental Research Funds for the Central Universities,Chinathe Program for New Century Excellent Talents in Universitythe CETC 54 Project(No.ITD-U14001/KX142600008)
文摘Controllers play a critical role in software-defined networking(SDN).However,existing singlecontroller SDN architectures are vulnerable to single-point failures,where a controller's capacity can be saturated by flooded flow requests.In addition,due to the complicated interactions between applications and controllers,the flow setup latency is relatively large.To address the above security and performance issues of current SDN controllers,we propose distributed rule store(DRS),a new multi-controller architecture for SDNs.In DRS,the controller caches the flow rules calculated by applications,and distributes these rules to multiple controller instances.Each controller instance holds only a subset of all rules,and periodically checks the consistency of flow rules with each other.Requests from switches are distributed among multiple controllers,in order to mitigate controller capacity saturation attack.At the same time,when rules at one controller are maliciously modified,they can be detected and recovered in time.We implement DRS based on Floodlight and evaluate it with extensive emulation.The results show that DRS can effectively maintain a consistently distributed rule store,and at the same time can achieve a shorter flow setup time and a higher processing throughput,compared with ONOS and Floodlight.
基金the senior personnel of Jiangsu University foundation(Grant No.13JDG31)the priority academic program development of Jiangsu Higher Education Institutions(Grant No.2014037).
文摘Sucrose is the main constituent of assimilation transport from source to sink.In order to study the transport mechanism of sucrose,the sucrose at stem was taken as a research object and the sucrose flow field in tomato stem was analyzed using CFD ANSYS FLUENT simulation.The results showed that the sucrose pressure distribution was lower at bottom node and higher at middle node.The velocity of sucrose at different nodes was higher at the bottom node and lower at middle node and assimilation flow direction of the first,second,and third leaf from the bottom was towards the roots.The result of verification experiment showed that sucrose content measured at different nodes was higher at middle node than that of bottom node.Results of this study confirmed that ANASYS FLUENT can better simulate sucrose migration in greenhouse tomato stem.This study provides a new method for studying the partitioning mechanism of tomato assimilates in greenhouse.