Effect of samarium doped ceria nanoparticles impregnation on the performance of anode supported SOFC with(Pr_(0.7)Ca_(0.3))_(0.9)MnO_(3-δ) cathode

Solid oxide fuel cell(SOFC) electrodes,after a high temperature sintering,may be impregnated to deposit nanoparticles within their pores to enhance the catalytic function.Samarium doped CeO2(SDC) nanoparticles were infiltrated into(Pr0.7Ca0.3)0.9MnO3-δ(PCM) cathode of anode supported SOFC cells.The cell with 2.6 mg/cm2 SDC impregnated in cathode showed the maximum power density of 580 mW/cm2 compared with 310 mW/cm2 of the cell without impregnation at 850 °C.The cells were also characterized with the impeda...

Research on Calcium Doped Ceria Used in Intermediate-Temperature SOFCs Anodes

As a mixed ion-electronic conductor, doped ceria, especially rare earth doped ceria, were used as anodes or components of anodes in SOFCs. In this work, calcium doped ceria （CCO） was synthesized to be used in intermediate-temperature SOFCs （IT-SOFCs） anodes in order to reduce the cost of anode-supported SOFCs. Electrical conductivity of 20% calcium doped ceria （20CCO） reached 0.209 S·cm^-1 in hydrogen at 850 ℃, and 0.041 S·cm^-1 in air at 800℃, which is about 0.04 S·cm^-1 lower than that of conventional samaria-doped ceria （0.079 S·cm^-1）. Electrochemical performance of Ni-20CCO cermet as anode was investigated using a fuel cell with 35μm-thick SDC electrolyte and Sm0.5Sr0.5 Co-SDC cathode. Maximum power density was 623 mW·cm^-2 under humidified （3% H2O） hydrogen at 650 ℃, inferring high catalytic activity of the Ni-20CCO anode.

Influence of Lithium Oxide Addition on the Sintering Behavior and Electrical Conductivity of Gadolinia Doped Ceria

Ceria-based electrolytes have been widely researched in intermediate-temperature solid oxide fuel cell （SOFC）, which might be operated at 500-600℃. Sintering behavior with lithium oxide as sintering additive and electrical conductivity of gadolinia doped ceria （GdonCe0.902-σ, GDC10） electrolyte was studied in this paper by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and electrochemical impedance spectroscopy （EIS）. As the results,, the fully dense GDC10 electrolytes are obtained at a low temperature of 800℃ with 2.5 mol% Li20 as sintering additive （called 5LiGDCS00）. During sintering process, lithium oxides adsorbed by around GDC10 surface help to sinter at 800~C and are kept at the grain boundary of GDC10 in the end. The fine grains of 100-400 nm and high electrical conductivity of 0.014 S/cm at 600~C in 5LiGDC800 were achieved, which contributed to the lower sintering temperature and enhanced grain boundary conductivity, respectively. Lithium, staying at grain boundary, reduces the depletion of oxygen vacancies in the space charge layers and increases the oxygen vacancy concentration in the grain boundary, which leads to improve the total electrical conductivity of 5LiGDC800.

Ionic conductivity of infiltrated Ln (Ln = Gd, Sm, Y)-doped ceria

This work studies the ionic conductivity of nanosized Gd-, Sm-, and Y-doped ceria prepared by the infiltration/impregnation method. The nanoparticles were deposited onto porous pure ceria substrates via infiltration- heating processes, and the conductivity was determined with the electrochemical impedance spectroscopy （EIS） using the conductive model for infiltrated phases. The conductivity of the infiltrated doped ceria changes with the doping amount, and Gd0.25Ce0.75O2-δ, Sm0.2Ce0.8O2-δ, and Y0.15Ce0.85O2-δ show the highest values of 2.56, 3.01, and 2.07 × 10-3 S.cm-1 at 600 ℃, respectively. Overall, Sin-doped samples show the highest conductivity, whileY-doped samples show the lowest conductivity. In con- sideration of the Bruggeman factor, the intrinsic conduc- tivity of the infiltrated doped ceria was calculated. Compared with the bulk doped ceria, the intrinsic con- ductivity is higher while the activation energy is lower, which may suggest different conduction mechanisms. Besides, co-doping effects on the conductivity of the infiltrated sample are less obvious than those of the bulk sample.

Isothermal and athermal martensitic transformations of ceria cerla doped zilrconian

Martensitic transformation behavior was studied for zirconia containing 4%～10% CeO2 (in mole fraction) by using a dilatometric method. The Ms (Martensite start temperature) decreased near linearly with increasing CeO2. Different transformation modes were observed depending on the composition and cooling rate. ZrO2 containing 6% CeO2 showed isothermal transformation behavior, whereas ZrO2 containing 9% and 10% CeO2 showed athermal transformation behavior. However, ZrO2 containing 8% CeO2 showed either isothermal or athermal transformations behavior depending on the cooling rate. A TTT (Time-Temperature-Transformation) diagram was proposed for ZrO2 containing 8% CeO2.

Study on rare earth/alkaline earth oxide-doped CeO_2 solid electrolyte

Five types of rare earth/alkaline earth oxide-doped CeO2 superfine-powders were synthesized by a low-temperature combustion technique. The relevant solid electrolyte materials were also sintered by pressureless sintering at different temperatures. The results of X-ray diffraction and transmission electron microscopy showed that the grain size of the powders was approximately 20-30 nm, and rare earth/alkaline earth oxides were completely dissolved into ceria-based solid solution with fluorite structure. The electrical conductivities of the SmzO3-CeO2 system were measured by the ac impedance technique in air at temperatures ranging from 513-900℃. The results indicated that the ionic conductivities of Srno.2oCe0.8Ol.875 solid electrolyte increase with increasing sintering temperature, and the relationship between the conductivities and measuring temperature obeys the An＇henius equation. Then the SmzO3-CeO2 material was further doped with other rare earth/alkaline earth oxide, and the conductivities improve with the effective index.

Sintering of Ce_(0.8)Sm_(0.2)O_(1.9)

Ce0.8Sm0.2O1.9（SDC）powder was prepared with an oxalate coprecipitation route.SDC solid solutions were sintered at various temperatures ranging from 1100~1450 ℃,and characterized by X-ray diffraction（XRD）,scanning electron microscopy（SEM）,density measurements,and electrical conductivity measurements.The optimized processing parameters for densification were to uniaxially press the sample at 200~400 MPa and sinter it at 1350~1400 ℃ for 4 h.The density of the sintered pellets was 〉90% of the theoretical density;their soakage was 〈0.5%;and the average grain size was 1~2 μm.The conductivities of the typical sintered specimen were 0.0133 and 0.0211 S·cm-1 at 550 and 600 ℃,respectively;Its activation energy for ionic conductivity was 0.62 eV.The dense SDC bulk material could be used as the electrolyte layer of low temperature solid oxide fuel cells.

Synthesis and characterization of Ce_(0.8)Sm_(0.2)O_(1.9) nanopowders using an acrylamide polymerization process

Ce0.8Sm0.2O1.9(SDC) nanopowders were synthesized by an acrylamide polymerization process.The XRD results showed that SDC powders prepared at 700 °C possessed a cubic fluorite structure.Transmission electron microscopy(TEM) indicated that the particle sizes of powders were in the range of 10-15 nm.A 98.3% of theoretical density was obtained when the SDC pellets were sintered at 1350 °C for 5 h,indicating that the powders had good sinterability.The conductivity of the sintered SDC ceramics was 0.019 S/cm at 6...

Synthesis and Electrical Conductivities of Sm_2O_3-CeO_2 Systems

Doped Ceria nano-powders were synthesized via a Pechini-type gel rout. The specific surface area of Ce_(0.8)Sm_(0.2)O_(1.9) powder measured by the multilayer BET method is 41 m2.g^(-1). The electrical conductivities of Sm_2O_(3)-CeO_2 systems were measured by the ac impedance technique in air at temperatures ranging from 513 to 900 ℃. Typical impedance spectra consist of two depressed semicircles at reduced measuring temperature and one depressed semicircle at elevated measuring temperature respectively, from which the grain interior and grain boundary conductivities were calculated. The relationship between the conductivities of Sm_2O_3 doped CeO_2 (SDC) electrolyte and measuring temperature obeys Arrhenius equation. The grain interior conductivity of SDC varies slightly with improving sintering temperature, while the total conductivity increases with enhancing sintering temperature. The effective index has a significant effect on the ionic conductivity of ceria doped based electrolyte. When the effective index improves, the ionic conductivity increases and the apparent conductance activation energy decreases.

Synthesis and Characterization of Sm_xGd_yCe_(1-x-y)O_(2-δ) Nanopowders

SmxGdyCe1-x-yO2-δ (x+y=0.2 and x=0, 0.04, 0.08, 0.12, 0.16, 0.2) nanopowders were prepared by a copre-cipitation method. The zeta potential and sedimentation volume of Ce(OH)4 aqueous dispersions at different pH values were measured. The isoelectric point (IEP) of Ce(OH)4 suspensions is 7.0. The maximum potential value of -18.5 mV and maximum sedimentation volume of 19 ml are reached at pH=10. The evolution behaviors of the xSm(OH)3·yGd(OH)3·(1-x-y)Ce(OH)4 dried powders in the heating process was characterized by DTA/TG and XRO. The powders decompose to ceria based solid solution at a temperature below 300℃ and forms cubic fluorite structure ceria at about 650℃. The properties of SmxGdyCe1-x-yO2-δ solid solutions were characterized by XRD, TEM and BET. The lattice parameter of doped Ce02 increases linearly with increasing Sm3+ substitution (or decreasing Gd3+ substitution). The particle size of the doped ceria powders is from 5 nm to 10 nm.

Enhancing cathode performance for CO2 electrolysis with Ce0.9M0.1O2-δ（M=Fe, Co, Ni） catalysts in solid oxide electrolysis cell

Electrochemical conversion with solid oxide electrolysis cells is a promising technology for CO2 utilization and simultaneously store renewable energy.In this work,Ce0.9M0.1O2-δ(CeM,M=Fe,Co,Ni)catalysts are infiltrated into La0.6Sr0.4Cr0.5Fe0.5O3-δ-Gd0.2Ce0.8O2-δ(LSCr Fe-GDC)cathode to enhance the electrochemical performance for CO2 electrolysis.CeCo-LSCrFe-GDC cell obtains the best performance with a current density of 0.652 A cm^-2,followed by CeFe-LSCrFe-GDC and CeNi-LSCrFe-GDC cells with the value of 0.603 and 0.535 A cm^-2,respectively,about 2.44,2.26 and 2.01 times higher than that of the LSCrFe-GDC cell at1.5 V and 800℃.Electrochemical impedance spectra combined with distributions of relaxed times analysis shows that both CO2 adsorption process and the dissociation of CO2 at triple phase boundaries are accelerated by Ce M catalysts,while the latter is the key rate-determining step.

Composite Cathode Bi_(1.14)Sr_(0.43)O_(2.14)-Ag for Intermediate-temperature Solid Oxide Fuel Cells

Composites consisting of strontium stabilized bismuth oxide （Bi1.14Sr0.43O2.14, SSB） and silver were investigated as cathodes for intermediate-temperature solid oxide fuel cells with doped ceria electrolyte. There were no chemical reactions between the two components. The microstructure of the interfaces between composite cathodes and Ce0.8Sm0.2O1.9 （SDC） electrolytes was examined by scanning electron microscopy （SEM）. Impedance spectroscopy measurements show that the performance of cathode fired at 700 ℃ is the best. When the content of Ag2O is 70 wt%, polarization resistance values for the SSB-Ag cathodes are as low as 0.2 Ωcm^2 at 700℃ and 0.29 Ωcm^2 at 650℃. These results are much smaller than some of other reported composite cathodes on doped ceria electrolyte and indicate that SSB-Ag composite is a potential cathode material for intermediate temperature SOFCs.