Slow driving control of tracked vehicles with automated mechanical transmission based on fuzzy logic

In order to move tracked vehicles at an extremely slowspeed with automated mechanical transmission（ AMT）,slowdriving function was added in the original system. The principle and requirement of slowdriving function were analyzed. Based on analysis of slow driving characteristic,identification of slowdriving condition and fuzzy control algorithm,a control strategy of the clutch was designed. In order to realize slowdriving,the clutch was controlled in a slipping mode as manual driving. The vehicle speed was increased to a required speed and kept in a small range by engaging or disengaging the clutch to the approximate half engagement point. Based on the control strategy,a control software was designed and tested on a tracked vehicle with AMT. The test results showthat the control of the clutch with the slowdriving function was smoother than that with original systemand the vehicle speed was slower and steadier.

Electromechanical coupling driving control for single-shaft parallel hybrid powertrain

The single-shaft parallel hybrid powertrain with the automatic mechanical transmission(AMT)is an efficient hybrid driving system in the hybrid electric bus(HEB),while the electromechanical coupling driving control becomes a complicated question to find a transient optimal control method to distribute the power between the engine and the electric machine(EM).This paper proposes an innovative control method to deal with the complicated transient coupling driving process of the electromechanical coupling driving system,considering the accelerating condition and the cruising condition mostly in the city driving cycle of HEB.The EM might be operated at driving mode or generating mode to assist the diesel engine to work in its high-efficiency area.Therefore,the adaptive torque tracking controller has been brought forward to ensure that the EM implements the demand torque as well as compensate the torque fluctuation of diesel engine.The d?q axis mathematical model and back stepping method are employed to deduce the adaptive controller and its adaptive laws.Simulation results demonstrate that the proposed control scheme can make the output torque of two power sources respond rapidly to the demand torque from the powertrain in the given driving condition.The proposed method could be adopted in the real control of HEB to improve the efficiency of the hybrid driving system.

Control Schemes for Driving Electro-optic Array Beam Deflectors

The beam deflectors based on electro-optic phased array（EOPA） is mainly described, and then an analysis on existing control schemes for driving the EOPA beam deflectors, based on custom hard-wired electronics or based on software in a microcontroUer, is made. Compared with these, a driving and control system for a multi-channel EOPA beam deflector is presented, in which the control assignment is implemented with a field programmable gate array（FPGA） chip. For different performance requirements, two control schemes, one with the serial scheme and another with the parallel scheme, have been explored and rapidly prototyped in Xilinx FPGA chips. With the control structures for the EOPA beam deflector, scanning rates of 588 kHz and 5 MHz can be respectivelv reached.

Failure laws of narrow pillar and asymmetric control technique of gob-side entry driving in island coal face

In allusion to the problems of complex stress distribution in the surrounding rock and deformation failure laws, as well as the difficulty in roadway supporting of the gob-side entry driving in the island coal face, 2107 face in Chengjiao Colliery is researched as an engineering case. Through physical mechanical test of rock, theoretical and numerical simulation analyses of rock, the analysis model of the roadway overlying strata structure was established, and its parameters quantified. To reveal the deformation law of the surrounding rock, the stability of the overlying strata structure was studied before, during and after the roadway driving. According to the field conditions, the stress distribution in coal pillar was quantified, and the surrounding rock deformation feature studied with different widths of the pillars in gob-side entry driving. Finally, the pillar width of 4 m was considered as the most reasonable. The research results show that there is great difference in support conditions among roadway roof, entity coal side and narrow pillar side. Besides, the asymmetric control technique for support of the surrounding rock was proposed. The asymmetric control technique was proved to be reasonable by field monitoring, support by bolt-net, steel ladder and steel wire truss used in narrow pillar side.

Stability of coal pillar in gob-side entry driving under unstable overlying strata and its coupling support control technique

Considering the situation that it is difficult to control the stability of narrow coal pillar in gob-side entry driving under unstable overlying strata, the finite difference numerical simulation method was adopted to analyze the inner stress distribution and its evolution regularity, as well as the deformation characteristics of narrow coal pillar in gob-side entry driving, in the whole process from entry driving of last working face to the present working face mining. A new method of narrow coal pillar control based on the triune coupling support technique (TCST), which includes that high-strength prestressed thread steel bolt is used to strain the coal on the goaf side, and that short bolt to control the integrity of global displacement zone in coal pillar on the entry side, and that long grouting cable to fix anchor point to constrain the bed separation between global displacement zone and fixed zone, is thereby generated and applied to the field production. The result indicates that after entry excavating along the gob under unstable overlying strata, the supporting structure left on the gob side of narrow coal pillar is basically invalid to maintain the coal-pillar stability, and the large deformation of the pillar on the gob side is evident. Except for the significant dynamic pressure appearing in the coal mining of last working face and overlying strata stabilizing process, the stress variation inside the coal pillar in other stages are rather steady, however, the stress expansion is obvious and the coal pillar continues to deform. Once the gob-side entry driving is completed, a global displacement zone on the entry side appears in the shallow part of the pillar, whereas, a relatively steady fixed zone staying almost still in gob-side entry driving and present working face mining is found in the deep part of the pillar. The application of TCST can not only avoid the failure of pillar supporting structure, but exert the supporting capacity of the bolting structure left in the pillar of last sublevel entry, thus to jointly maintain the stability of coal pillar.

Fault Detection for Motor Drive Control System of Industrial Robots Using CNN-LSTM-based Observers

The complex working conditions and nonlinear characteristics of the motor drive control system of industrial robots make it difficult to detect faults.In this paper,a deep learning-based observer,which combines the convolutional neural network(CNN)and the long short-term memory network(LSTM),is employed to approximate the nonlinear driving control system.CNN layers are introduced to extract dynamic features of the data,whereas LSTM layers perform time-sequential prediction of the target system.In terms of application,normal samples are fed into the observer to build an offline prediction model for the target system.The trained CNN-LSTM-based observer is then deployed along with the target system to estimate the system outputs.Online fault detection can be realized by analyzing the residuals.Finally,an application of the proposed fault detection method to a brushless DC motor drive system is given to verify the effectiveness of the proposed scheme.Simulation results indicate the impressive fault detection capability of the presented method for driving control systems of industrial robots.

New digital drive phase control for improving bias stability of silicon MEMS gyroscope

In order to improve the bias stability of the micro-electro mechanical system（MEMS） gyroscope and reduce the impact on the bias from environmental temperature,a digital signal processing method is described for improving the accuracy of the drive phase in the gyroscope drive mode.Through the principle of bias signal generation,it can be concluded that the deviation of the drive phase is the main factor affecting the bias stability.To fulfill the purpose of precise drive phase control,a digital signal processing circuit based on the field-programmable gate array（FPGA） with the phase-lock closed-loop control method is described and a demodulation method for phase error suppression is given.Compared with the analog circuit,the bias drift is largely reduced in the new digital circuit and the bias stability is improved from 60 to 19 °/h.The new digital control method can greatly increase the drive phase accuracy,and thus improve the bias stability.

Cloud Control System Architectures,Technologies and Applications on Intelligent and Connected Vehicles:a Review

The electrification of vehicle helps to improve its operation efficiency and safety.Due to fast development of network,sensors,as well as computing technology,it becomes realizable to have vehicles driving autonomously.To achieve autonomous driving,several steps,including environment perception,path-planning,and dynamic control,need to be done.However,vehicles equipped with on-board sensors still have limitations in acquiring necessary environmental data for optimal driving decisions.Intelligent and connected vehicles(ICV)cloud control system(CCS)has been introduced as a new concept as it is a potentially synthetic solution for high level automated driving to improve safety and optimize traffic flow in intelligent transportation.This paper systematically investigated the concept of cloud control system from cloud related applications on ICVs,and cloud control system architecture design,as well as its core technologies development.Based on the analysis,the challenges and suggestions on cloud control system development have been addressed.

Direct Yaw Moment Control for Distributed Drive Electric Vehicle Handling Performance Improvement

For a distributed drive electric vehicle（DDEV） driven by four in-wheel motors, advanced vehicle dynamic control methods can be realized easily because motors can be controlled independently, quickly and precisely. And direct yaw-moment control（DYC） has been widely studied and applied to vehicle stability control. Good vehicle handling performance： quick yaw rate transient response, small overshoot, high steady yaw rate gain, etc, is required by drivers under normal conditions, which is less concerned, however. Based on the hierarchical control methodology, a novel control system using direct yaw moment control for improving handling performance of a distributed drive electric vehicle especially under normal driving conditions has been proposed. The upper-loop control system consists of two parts： a state feedback controller, which aims to realize the ideal transient response of yaw rate, with a vehicle sideslip angle observer; and a steering wheel angle feedforward controller designed to achieve a desired yaw rate steady gain. Under the restriction of the effect of poles and zeros in the closed-loop transfer function on the system response and the capacity of in-wheel motors, the integrated time and absolute error（ITAE） function is utilized as the cost function in the optimal control to calculate the ideal eigen frequency and damper coefficient of the system and obtain optimal feedback matrix and feedforward matrix. Simulations and experiments with a DDEV under multiple maneuvers are carried out and show the effectiveness of the proposed method： yaw rate rising time is reduced, steady yaw rate gain is increased, vehicle steering characteristic is close to neutral steer and drivers burdens are also reduced. The control system improves vehicle handling performance under normal conditions in both transient and steady response. State feedback control instead of model following control is introduced in the control system so that the sense of control intervention to drivers is relieved.

STUDY ON SENSOR-BASED CONTROL METHOD FOR HARMONIC DRIVE SYSTEM

A new type of robust traje ctory tracking control for harmonic using joint torque sensor and joint acceleration sensor information is concerned with.Joint torque sensor information is used to compensate the uncertainty of link and load parameters. Joint acceleration feedback control will enhace the robustness of the driving system, resist the dynamic uncertainties and disturbing torque acted on the joint axis within definite bandwidth, improve the joint tracking performance, and resist the vibration of the load side of the harmonic drive system. Experimental studies are carried out and comparison of several controllers , such as PD and sensor- based control, the experimental results clearly illustrate the effectiveness of the proposed methods.

Force Control Compensation Method with Variable Load Stiffness and Damping of the Hydraulic Drive Unit Force Control System

Each joint of hydraulic drive quadruped robot is driven by the hydraulic drive unit（HDU）, and the contacting between the robot foot end and the ground is complex and variable, which increases the difficulty of force control inevitably. In the recent years, although many scholars researched some control methods such as disturbance rejection control, parameter self-adaptive control, impedance control and so on, to improve the force control performance of HDU, the robustness of the force control still needs improving. Therefore, how to simulate the complex and variable load characteristics of the environment structure and how to ensure HDU having excellent force control performance with the complex and variable load characteristics are key issues to be solved in this paper. The force control system mathematic model of HDU is established by the mechanism modeling method, and the theoretical models of a novel force control compensation method and a load characteristics simulation method under different environment structures are derived, considering the dynamic characteristics of the load stiffness and the load damping under different environment structures. Then, simulation effects of the variable load stiffness and load damping under the step and sinusoidal load force are analyzed experimentally on the HDU force control performance test platform, which provides the foundation for the force control compensation experiment research. In addition, the optimized PID control parameters are designed to make the HDU have better force control performance with suitable load stiffness and load damping, under which the force control compensation method is introduced, and the robustness of the force control system with several constant load characteristics and the variable load characteristics respectively are comparatively analyzed by experiment. The research results indicate that if the load characteristics are known, the force control compensation method presented in this paper has positive compensation effects on the load characteristics variation, i.e., this method decreases the effects of the load characteristics variation on the force control performance and enhances the force control system robustness with the constant PID parameters, thereby, the online PID parameters tuning control method which is complex needs not be adopted. All the above research provides theoretical and experimental foundation for the force control method of the quadruped robot joints with high robustness.

OPTIMAL TORQUE CONTROL STRATEGY FOR PARALLEL HYBRID ELECTRIC VEHICLE WITH AUTOMATIC MECHANICAL TRANSMISSION

In parallel hybrid electrical vehicle （PHEV） equipped with automatic mechanical transmission （AMT）, the driving smoothness and the clutch abrasion are the primary considerations for powertrain control during gearshift and clutch operation. To improve these performance indexes of PHEV, a coordinated control system is proposed through the analyzing of HEV powertrain dynamic characteristics. Using the method of minimum principle, the input torque of transmission is optimized to improve the driving smoothness of vehicle. Using the methods of fuzzy logic and fuzzy-PID, the engaging speed of clutch and the throttle opening of engine are manipulated to ensure the smoothness of clutch engagement and reduce the abrasion of clutch friction plates. The motor provides the difference between the required input torque of transmission and the torque transmitted through clutch plates. Results of simulation and experiments show that the proposed control strategy performs better than the contrastive control system, the smoothness of driving and the abrasion of clutch can be improved simultaneously.

Development of Super-Synchronization Speed Control Assembly in Two 80 MVA Motor Generators of HL-2A Tokamak

The power of the toroidal field （TF） coil in HL-2A is supplied with two 80 MVA motor generators （MGs） together through a diode rectifier. The TF system is designed to obtain the parameters as follows： the highest toroidal filed of 2.8 T, the biggest coil current of 45 kA, the fiat top time of 3-5 s. So the released energy of each MG set for one pulse discharge mast be more than 500 MJ.

一类活动发射平台驱动控制系统网络设计

In order to ensure that a mobile launch platform is able to transport a launch vehicle which is assembled vertically on a complex orbit,a communication network for the drive control system was designed.Based on the char-acteristics of equipment of the drive control system and its position,Industrial Ethernet and Profibus were selected.To meet the requirements for reliability and maintainability of aerospace products,the communication network featured a hot redundant to avoid single point failure risk,so that if any point in the system fails,the control strategy of standby switches using heartbeat detection and parity check would ensure the normal communication and failure diagnostics,which could enable the transport mission of the launch vehicle to be completed smoothly.

A novel two-degree-of-freedom spherical ultrasonic motor using three travelling-wave type annular stators

In order to promote the tolerance and controllability of the multi-degree-of-freedom(M-DOF) ultrasonic motor, a novel two-degree-of-freedom(2-DOF) spherical ultrasonic motor using three traveling-wave type annular stators was put forward. Firstly,the structure and working principle of this motor were introduced, especially a spiral spring as the preload applied component was designed for adaptive adjustment. Then, the friction drive model of 2-DOF spherical motor was built up from spatial geometric relation between three annular stators and the spherical rotor which was used to analyze the mechanical characteristics of the motor.The optimal control strategy for minimum norm solution of three stators' angular velocity was proposed, using Moore-Penrose generalized inverse matrix. Finally, a 2-DOF prototype was fabricated and tested, which ran stably and controllably. The maximum no-load velocity and stall torque are 92 r/min and 90 m N·m, respectively. The 2-DOF spherical ultrasonic motor has compact structure, easy assembly, good performance and stable operation.

A Review of Drive Techniques for Multiphase Machines

Multiphase machines are gaining increasing popularity because of their distinct advantages over three-phase counterparts,such as reduced per phase power rating,improved reliability and increased degrees of freedom.This paper overviews the development history of multiphase machines and drive techniques in Section II.Three kinds of drive algorithms,including Field-Oriented Control(FOC),Direct Torque Control(DTC)and Model Predictive Control(MPC),are introduced in Section III.Then two types of fault-tolerant methods are compared in Section IV,which are the Vector Space Decomposition(VSD)strategy and Optimal Current Control(OCC)method.Furthermore,different types of existing multiphase converter topologies are listed in Section V,and various kinds of multiphase PWM methods are discussed in Section VI.Finally,based on the review,developing trends of multiphase drive techniques are forecasted.

Digital Design of Multi-Functional Rehabilitation Robot

The mechanical structure as well as the schematic organization has been designed to achieve lower limb rehabilitation training function; Solidworks has been used to model the robot. And the robot has been optimized by the means of human-interference engineering. The primary components of the robot have been analyzed by Ansys workbench.

Extreme Dynamics on Electronic Cam Linear Drive

One of the requirements for modem production machine is versatility and easy reconfiguration to produce new products. The production machines use fixed gearing and mechanical cams in history. The cams were used for specific stokes and cam switches were used for commissioning of technological process. This solution has disadvantages in lower production speed and no flexibility of production. This article summaries practical steps for machine modernization and highlight practical problems in modernization of older production machine. The electronic cam with direct linear drive was used for traversal motion with high peak acceleration. This paper discusses cam stoke curve design, redesign and fitting.

Design and implementation of a high precision and wide range adj ustable LED drive controller

This paper presents a novel high precision and wide range adjustable LED constant-current drive controller design.Compared with the traditional technique,the conventional mirror resistance is substituted by a MOSFET with fixed drain voltage,and a negative feedback amplifier is used to keep all mirror device voltages equal,so that the output current is precise and not affected by the load supply voltage.In addition,the electric property of the mirror MOSFET is optimized by a current subsection mirror（CSM） mechanism,thus ensuring a wide range of output current with high accuracy.A three-channel LED driver chip based on this project is designed and fabricated in the TSMC 0.6μm BCD process with a die area of 1.1×0.7 mm^2.Experimental results show that the proposed LED drive controller works well, and,as expected,the output current can be maintained from 5 to 60 mA.A relative current accuracy error of less than 1%and a maximal relative current matching error of 1.5%are successfully achieved.

Configurations and Control of Traction Motors for Electric Vehicles:A Review

In recent decades,worldwide global warming and reduction in petroleum resources have accelerated researcher’s attention to produce alternative sustainable and environmentally clean transportation systems.Electrification of vehicular technology is capable of curbing the environmental pollution problem in an efficient and effective way,due to high efficiency electric motors,development and advancement in the field of power electronic devices,digital signal processing and advanced control techniques.This article presents a comprehensive review on different configurations/architecture of electric vehicles(EVs)and hybrid electric vehicles(HEVs),traction motors for electric propulsion system and high performance speed sensorless control of traction drive.The basic architecture key components of hybrid vehicle and different power train configurations with respect to applications and limitations are discussed.The integral part of electric propulsion system,traction motor classes for desired operational characteristics and limitations are summarized from a system perspective with the latest improvements.High performance traction motor control techniques are discussed with respect to automotive applications.Finally,speed sensorless control techniques research trends as well as an extensive review on rotor speed estimation techniques for robust and efficient sensorless traction drive control are highlighted.This article provides state of the art key global trends and tradeoff of various technologies with future trends and potential areas of research.