Dynamical Mechanisms of Effects of Landslides on Long Distance Oil and Gas Pipelines

According to the investigations on the oil and gas pipelines such as the Lan-Cheng-Chong pipeline and the Southwest pipeline, there are two ways of laying pipeline： pipelines paralleling （approximately） to the main slide direction and pipelines perpendicular （approximately） to the main slide direction. If earth-retaining walls have been built for pipelines paralleling to the main slide direction, they will prevent the lands from sliding; On the contrary, without earth-retaining walls, the sharp broken rocks in the backfilling soil will scratch the safeguard of the pipeline when the landslides take place. Pipelines perpendicular to the main slide direction can be classified into four types according to the relative positions between pipelines and landslides： Pipelines over the slide planes, pipelines inside the fracture strips of slide planes, pipelines below the slide planes and pipelines behind the backsides of landslides. The different dynamical mechanisms of the process in which landslide acts against pipelines are analyzed based on whether the pipelines are equipped with fixed frusta, because the sliding resistance depends on whether and how many fixed frusta are equipped and the distance between frusta.

Summery Intra-Tidal Variations of Suspended Sediment Transportation–Topographical Response and Dynamical Mechanism in the Aoshan Bay and Surrounding Area,Shandong Peninsula

As the second largest bay in Qingdao,the Aoshan Bay and its adjacent sea area play an important role in aquaculture development and urban land and sea coordination for the eastern gulf type of city in the Qingdao Blue Silicon Valley Core Area(QBSVCA).Based on in-situ sedimentary dynamical observation and previous research results,the thermohaline structure,the transportation of suspended sediment and its mechanism,and the coastal geomorphic response were elaborated and analyzed in detail in this paper.The result indicated that the thermohaline and density distribution have obvious intra-tidal characteristics in the QBSVCA and the adjacent waters of the islands,during summer neap tide stage.The development of the bottom high suspended sediment concentration(SSC)layer was slightly enhanced in flood slack at each of the four stations.Suspended sediment transportation near the QBSVCA is related closely with the vertical mixing-stratification mechanism.Combined with previous research results,this study once again showed that submarine topography and the grain size of sea bed sediments would respond to hydrodynamic forces.The medians of the bottom E and D50 in the Aoshan Bay were the highest,followed by those in the Daguan Island and Xiaoguan Island,and the data in the Laoshan Bay were the lowest.This showed that the capacity of suspended sediment transportation in the bottom water layer of the Aoshan Bay was stronger than that of the adjacent sea area.The re-suspension and migration of fine sediments lead to the strong coarsening of sediments in this area.

MESOSCALE RAINBANDS AHEAD OF COLD FRONTS IN NORTH CHINA AND THEIR DYNAMICAL MECHANISMS

Among 33 cold frontal systems passed over the Beijing-Tianjin-Tangshan area from May to August during 1963—1979,there existed mesoscale rainbands in the warm sectors ahead of 31 cold fronts.These rainbands, according to their orientation,movement,formation and development,can be divided into three types:parallel, angulate and perpendicular type.The basic characteristics,sources and propagation of the three types of rainbands and the severe convective weather associated with the bands are presented.The possible mechanis- ms responsible for the formation and development of the bands are also briefly discussed.

Study on the effect of focal position change on the expansion velocity and propagation mechanism of plasma generated by millisecond pulsed laser-induced fused silica

In this work, by controlling the positional relationship between the target and the focal point, the surface damage, shock wave phenomenon and propagation mechanism involved in the plasma generation of fused silica by millisecond pulsed laser irradiation at different focal positions were studied. Laser energy is an important experimental variable. The dynamic process of plasma was detected by optical shadow method, and the influence of surface film damage on plasma propagation and the propagation mechanism at different focal positions were discussed. The study found that the plasma induced by the pulsed laser at the focus position within 0–20 μs exploded, the micro-droplets formed around 20 μs. At the same time, a shock wave is formed by the compressed air, the micro-droplets are compressed under the action of the shock wave recoil pressure, and the micro-droplets channel phenomenon is observed in the micro-droplets. The peak velocities of plasma and combustion wave appear earlier in the pre-focus position than in the post-focus position. This research provides a reference for the field of laser processing using fused silica as the substrate.

Spatial differentiation and dynamic mechanism of micro-geomorphology based on acoustic spectrum data of the Huanghe(Yellow)River Delta

Submarine micro-geomorphology is a geo-morphological type occurring in shallow and surface areas of seabed.The combined relationships and distribution of the micro-geomorphology indirectly reflect coupling relationships among the sediment deposition,dynamic environment,and geomorphologic evolution.Spatial differentiation and dynamic changes in micro-geomorphology were studied based on acoustic data interpretation from a wide range(3200 km^(2))of the Huanghe(Yellow)River delta(HRD).The combination of the sub-bottom profiler and the side-scan sonar methods allowed for the identification of submarine shallow micro-geomorphologic types,as well as their scale and spatial distributions.There were seven typical micro-geomorphologic features in the shallow and surface areas of the HRD,including buried ancient channels,stratigraphic disturbances,scour troughs,sand waves,pits,erosional remnants,and sand spots.The coupling and superposition of the sediment,sediment characteristics,seabed scouring and silting,and hydrodynamic conditions of the Huanghe River had combined effects on the patterns of micro-geomorphologic types,characteristics,and ranges.From the perspective of acoustic profile interpretations,the scale,range,and spatial locations of the microgeomorphology in the HRD revealed seasonal variation characteristics,and the spatial distributions displayed significant regional differentiation characteristics.In addition,strong stratigraphic disturbances and areas with densely distributed buried ancient channels reflected the activity and instability of the submarine shallow strata.Through the interpretation of the sub-bottom profile detection data,the diversion processes of the flow paths in the lower reaches of the Huanghe River were obtained for a certain historical period in the coastal waters of the HRD.This study further clarified the relationships between the micro-geomorphologic features and spatial combinations,which is important for research on micro-geomorphologic features and their dynamic mechanisms.

MODELLING OF MECHANICAL MECHANISM OF CHROMATOGRAPHIC SYSTEM AND THEORETICAL EQUATIONS SHOWING DYNAMICAL CHARACTERISTICS OF CHROMATOGRAPHY

A simple model of chromatographic mechanical mechanism is present, and then a scrics of theoretical chromatographic equations and fundamental Formulae are derived. These theoretical equations and formulae not only reserve thermodynamic characteristics in the current fundamental chromatographic formulae, but also introduce one or more kinetic parameter, so it is possible to make the macroscopic-control on the effect of kinetic characteristics on chromatographic system.

Dynamic recrystallization mechanisms during hot compression of Mg-Gd-Y-Nd-Zr alloy

Hot compression tests were conducted on a homogenized Mg-7Gd-4Y-1Nd-0.5Zr alloy at 450 ℃ and a strain rate of 2 s-1. Dynamic recrystallization （DRX） mechanisms were investigated by optical microscope （OM）, scanning electron microscope （SEM） and transmission electron microscope （TEM） systematically. The crystallographic orientation information is obtained through electron back-scattering diffraction （EBSD）. The result shows that the flow stress firstly reaches a peak rapidly followed by declining to a valley, and then increases gradually again when the alloy is compressed to a strain of-1.88. DRX related to {10]2} tensile twins is extensively observed at small strains, resulting in an evident grain refinement. DRX grains first nucleate along the edges of twin boundaries with about 30~ （0001） off the twin parents. While at large strains, conventional continuous DRX （CDRX） is frequently identified by the formation of small DRX grains along the original grain boundaries and the continuously increasing misorientation from the centre of large original grains to the grain boundaries. Evidence of particle-stimulated nucleation （PSN） is also observed in the present alloy.

Hybrid Dynamic Variables-Dependent Event-Triggered Fuzzy Model Predictive Control

This article focuses on dynamic event-triggered mechanism(DETM)-based model predictive control(MPC) for T-S fuzzy systems.A hybrid dynamic variables-dependent DETM is carefully devised,which includes a multiplicative dynamic variable and an additive dynamic variable.The addressed DETM-based fuzzy MPC issue is described as a “min-max” optimization problem(OP).To facilitate the co-design of the MPC controller and the weighting matrix of the DETM,an auxiliary OP is proposed based on a new Lyapunov function and a new robust positive invariant(RPI) set that contain the membership functions and the hybrid dynamic variables.A dynamic event-triggered fuzzy MPC algorithm is developed accordingly,whose recursive feasibility is analysed by employing the RPI set.With the designed controller,the involved fuzzy system is ensured to be asymptotically stable.Two examples show that the new DETM and DETM-based MPC algorithm have the advantages of reducing resource consumption while yielding the anticipated performance.

Analysis of mesoscopic mechanical dynamic characteristics of ballast bed with under sleeper pads

The meso-dynamical behaviour of a high-speed rail ballast bed with under sleeper pads(USPs)was studied.The geometrically irregular refined discrete element model of the ballast particles was constructed using 3D scanning techniques,and the 3D dynamic model of the rail-sleeper-ballast bed was constructed using the coupled discrete element method-multiflexible-body dynamics(DEM-MFBD)approach.We analyse the meso-mechanical dynamics of the ballast bed with USPs under dynamic load on a train and verify the correctness of the model in laboratory tests.It is shown that the deformation of the USPs increases the contact area between the sleeper and the ballast particles,and subsequently the number of contacts between them.As the depth of the granular ballast bed increases,the contact area becomes larger,and the contact force between the ballast particles gradually decreases.Under the action of the elastic USPs,the contact forces between ballast particles are reduced and the overall vibration level of the ballast bed can be reduced.The settlement of the granular ballast bed occurs mainly at the shallow position of the sleeper bottom,and the installation of the elastic USPs can be effective in reducing the stress on the ballast particles and the settlement of the ballast bed.

Research on the River-Crossing Development Process and Dynamic Mechanism in Nanchang City

With the deepening of the market economy and the big step of urbaniza- tion, the spatial restricted effect of the development of the riverside cities in China is becoming more and more obvious. The river-crossing development of cities is imperative. The Riverside New Area has gradually become the key area of urban development and the new economy growth pole. Based on the development history of Nanchang, the evolution of the river-crossing development of Nanchang city was analyzed systematically, and river-crossing development of Nanchang was divided into 3 stages of initial river-crossing development stage, slow river-crossing develop- ment stage and rapid river-crossing development stage. In-depth discussion was made to the dynamic mechanism of the river-crossing development in Nanchang.

Stability of bedded rock slopes subjected to hydro-fluctuation and associated strength deterioration

Reservoir-induced earthquakes(RIEs)occur frequently in the Three Gorges Reservoir Area(TGRA)and the rock mass strength of the hydro-fluctuation belt(HFB)deteriorates severely due to the reservoirinduced seismic loads.Three models of typical bedded rock slopes(BRSs),i.e.gently(GIS),moderately(MIS),and steeply(SIS)inclined slopes,were proposed according to field investigations.The dynamic response mechanism and stability of the BRSs,affected by the rock mass deterioration of the HFB,were investigated by the shaking table test and the universal distinct element code(UDEC)simulation.Specifically,the amplification coefficient of the peak ground acceleration(PGA)of the slope was gradually attenuated under multiple seismic loads,and the acceleration response showed obvious“surface effect”and“elevation effect”in the horizontal and vertical directions,respectively.The“S-type”cubic function and“steep-rise type”exponential function were used to characterize the cumulative damage evolution of the slope caused by microseismic waves(low seismic waves)and high seismic waves,respectively.According to the dynamic responses of the acceleration,cumulative displacement,rock pressure,pore water pressure,damping ratio,natural frequency,stability coefficient,and sliding velocity of the slope,the typical evolution processes of the dynamic cumulative damage and instability failure of the slope were generalized,and the numerical and experimental results were compared.Considering the dynamic effects of the slope height(SH),slope angle(SA),bedding plane thickness(BPT),dip angle of the bedding plane(DABP),dynamic load amplitude(DLA),dynamic load frequency(DLF),height of water level of the hydro-fluctuation belt(HWLHFB),degradation range of the hydro-fluctuation belt(DRHFB),and degradation shape of the hydro-fluctuation belt(DSHFB),the sensitivity of factors influencing the slope dynamic stability using the orthogonal analysis method(OAM)was DLA>DRHFB>SA>SH>DLF>HWLHFB>DSHFB>DABP>BPT.

Event-based nonfragile state estimation for memristive recurrent neural networks with stochastic cyber-attacks and sensor saturations

This paper addresses the issue of nonfragile state estimation for memristive recurrent neural networks with proportional delay and sensor saturations. In practical engineering, numerous unnecessary signals are transmitted to the estimator through the networks, which increases the burden of communication bandwidth. A dynamic event-triggered mechanism,instead of a static event-triggered mechanism, is employed to select useful data. By constructing a meaningful Lyapunov–Krasovskii functional, a delay-dependent criterion is derived in terms of linear matrix inequalities for ensuring the global asymptotic stability of the augmented system. In the end, two numerical simulations are employed to illustrate the feasibility and validity of the proposed theoretical results.

Dynamic Event-Triggered Consensus Control for Input Constrained Multi-Agent Systems With a Designable Minimum Inter-Event Time

This paper investigates the consensus control of multi-agent systems(MASs) with constrained input using the dynamic event-triggered mechanism(ETM).Consider the MASs with small-scale networks where a centralized dynamic ETM with global information of the MASs is first designed.Then,a distributed dynamic ETM which only uses local information is developed for the MASs with large-scale networks.It is shown that the semi-global consensus of the MASs can be achieved by the designed bounded control protocol where the Zeno phenomenon is eliminated by a designable minimum inter-event time.In addition,it is easier to find a trade-off between the convergence rate and the minimum inter-event time by an adjustable parameter.Furthermore,the results are extended to regional consensus of the MASs with the bounded control protocol.Numerical simulations show the effectiveness of the proposed approach.

Set-Membership Filtering Approach to Dynamic Event-Triggered Fault Estimation for a Class of Nonlinear Time-Varying Complex Networks

The present study addresses the problem of fault estimation for a specific class of nonlinear time-varying complex networks,utilizing an unknown-input-observer approach within the framework of dynamic event-triggered mechanism(DETM).In order to optimize communication resource utilization,the DETM is employed to determine whether the current measurement data should be transmitted to the estimator or not.To guarantee a satisfactory estimation performance for the fault signal,an unknown-input-observer-based estimator is constructed to decouple the estimation error dynamics from the influence of fault signals.The aim of this paper is to find the suitable estimator parameters under the effects of DETM such that both the state estimates and fault estimates are confined within two sets of closed ellipsoid domains.The techniques of recursive matrix inequality are applied to derive sufficient conditions for the existence of the desired estimator,ensuring that the specified performance requirements are met under certain conditions.Then,the estimator gains are derived by minimizing the ellipsoid domain in the sense of trace and a recursive estimator parameter design algorithm is then provided.Finally,a numerical example is conducted to demonstrate the effectiveness of the designed estimator.

Experimental and numerical study on dynamic mechanical behaviors of shale under true triaxial compression at high strain rate

High-energy gas fracturing of shale is a novel,high efficacy and eco-friendly mining technique,which is a typical dynamic perturbing behavior.To effectively extract shale gas,it is important to understand the dynamic mechanical properties of shale.Dynamic experiments on shale subjected to true triaxial compression at different strain rates are first conducted in this research.The dynamic stress-strain curves,peak strain,peak stress and failure modes of shale are investigated.The results of the study indicate that the intermediate principal stress and the minor principal stress have the significant influence on the dynamic mechanical behaviors,although this effect decreases as the strain rate increases.The characteristics of compression-shear failure primarily occur in shale subjected to triaxial compression at high strain rates,which distinguishes it from the fragmentation characteristics observed in shale under dynamic uniaxial compression.Additionally,a numerical three-dimensional Split Hopkinson Pressure Bar(3D-SHPB),which is established by coupling PFC3D and FLAC3D methods,is validated to replicate the laboratory characteristics of shale.The dynamic mechanical characteristics of shale subjected to different confining stresses are systematically investigated by the coupling PFC3D and FLAC3D method.The numerical results are in good agreement with the experimental data.

Research on Operation Optimization of Energy Storage Power Station and Integrated Energy Microgrid Alliance Based on Stackelberg Game

With the development of renewable energy technologies such as photovoltaics and wind power,it has become a research hotspot to improve the consumption rate of new energy and reduce energy costs through the deployment of energy storage.To solve the problem of the interests of different subjects in the operation of the energy storage power stations(ESS)and the integrated energy multi-microgrid alliance(IEMA),this paper proposes the optimization operation method of the energy storage power station and the IEMA based on the Stackelberg game.In the upper layer,ESS optimizes charging and discharging decisions through a dynamic pricing mechanism.In the lower layer,IEMA optimizes the output of various energy conversion coupled devices within the IEMA,as well as energy interaction and demand response(DR),based on the energy interaction prices provided by ESS.The results demonstrate that the optimization strategy proposed in this paper not only effectively balances the benefits of the IEMA and ESS but also enhances energy consumption rates and reduces IEMA energy costs.

Flexible Load Participation in Peaking Shaving and Valley Filling Based on Dynamic Price Incentives

Considering the widening of the peak-valley difference in the power grid and the difficulty of the existing fixed time-of-use electricity price mechanism in meeting the energy demand of heterogeneous users at various moments or motivating users,the design of a reasonable dynamic pricing mechanism to actively engage users in demand response becomes imperative for power grid companies.For this purpose,a power grid-flexible load bilevel model is constructed based on dynamic pricing,where the leader is the dispatching center and the lower-level flexible load acts as the follower.Initially,an upper-level day-ahead dispatching model for the power grid is established,considering the lowest power grid dispatching cost as the objective function and incorporating the power grid-side constraints.Then,the lower level comprehensively considers the load characteristics of industrial load,energy storage,and data centers,and then establishes a lower-level flexible load operation model with the lowest user power-consuming cost as the objective function.Finally,the proposed method is validated using the IEEE-118 system,and the findings indicate that the dynamic pricing mechanism for peaking shaving and valley filling can effectively guide users to respond actively,thereby reducing the peak-valley difference and decreasing users’purchasing costs.

Kinematics Analysis and Optimization of the Fast Shearing-extrusion Joining Mechanism for Solid-state Metal

Dynamical Joining of the solid-state metal is the key technology to realize endless hot rolling. The heating and laser welding method both require long joining time. Based on super deformation method, a 7-bar and 2-slider mechanism was developed in Japan, and the joining time is less than 0.5 s, however the length of each bar are not reported and this mechanism is complex. A relatively simple 6-bar and 1-slider mechanism is put forward, which can realize the shearing and extrusion motion of the top and bottom blades with a speed approximately equal to the speed of the metal plates. In order to study the kinematics property of the double blades, based on complex vector method, the multi-rigid-body model is built, and the displacement and speed functions of the double blades, the joining time and joining thickness are deduced, the kinematics analysis shows that the initial parameters can＇t satisfy the joining process. Hence, optimization of this mechanism is employed using genetic algorithm（GA） and the optimization parameters of this mechanism are obtained, the kinematics analysis show that the joining time is less than 0.1 s, the joining thickness is more than 80% of the thickness of the solid-state metal, and the horizontal speeds of the blades are improved. A new mechanism is provided for the joining of the solid-state metal and a foundation is laid for the design of the device.

Atmospheric Circulation and Dynamic Mechanism for Persistent Haze Events in the Beijing–Tianjin–Hebei Region

In this study, regional persistent haze events（RPHEs） in the Beijing–Tianjin–Hebei（BTH） region were identified based on the Objective Identification Technique for Regional Extreme Events for the period 1980–2013. The formation mechanisms of the severe RPHEs were investigated with focus on the atmospheric circulation and dynamic mechanisms. Results indicated that：（1） 49 RPHEs occurred during the past 34 years.（2） The severe RPHEs could be categorized into two types according to the large-scale circulation, i.e. the zonal westerly airflow（ZWA） type and the high-pressure ridge（HPR） type. When the ZWA-type RPHEs occurred, the BTH region was controlled by near zonal westerly airflow in the mid–upper troposphere.Southwesterly winds prevailed in the lower troposphere, and near-surface wind speeds were only 1–2 ms^-1. Warm and humid air originating from the northwestern Pacific was transported into the region, where the relative humidity was 70% to 80%, creating favorable moisture conditions. When the HPR-type RPHEs appeared, northwesterly airflow in the mid–upper troposphere controlled the region. Westerly winds prevailed in the lower troposphere and the moisture conditions were relatively weak.（3） Descending motion in the mid-lower troposphere caused by the above two circulation types provided a crucial dynamic mechanism for the formation of the two types of RPHEs. The descending motion contributed to a reduction in the height of the planetary boundary layer（PBL）, which generated an inversion in the lower troposphere. This inversion trapped the abundant pollution and moisture in the lower PBL, leading to high concentrations of pollutants.

Diagnostic experiments for transport mechanisms of suspended sediment discharged from the Yellow River in the Bohai Sea

Five diagnostic experiments with a 3D baroclinic hydrodynamic and sediment transport model ECOMSED in couple with the third generation wave model SWAN and the Grant-Madsen bottom boundary layer model driven by the monthly sediment load of the Yellow River, were conducted to separately diagnose effects of different hydrodynamic factors on transport of suspended sediment discharged from the Yellow River in the Bohai Sea. Both transport and spatio-temporal distribution of suspended sediment concentration in the Bohai Sea were numerially simulated. It could be from the Yellow River cannot be delivered in concluded that suspended sediment discharged long distance under the condition of tidal current. Almost all of sediments from the Yellow River are deposited outside the delta under the condition of wind-driven current, and only very small of them are transported faraway. On the basis of wind forcing, sediments from the Yellow River are mainly transported north-northwestward, and others which are first delivered to the Laizhou Bay are continuously moved northward. An obvious 3D structure characteristic of sediment transport is produced in the wind-driven and tide-induced residual circulation condition. Transport patterns at all layers are generally consistent with circulation structure, but there is apparent deviation between the depth-averaged sediment flux and the circulation structure. The phase of temporal variation of sediment concentration is consistent with that of the bottom shear stress, both of which are proved to have a ten-day cycle in wave and current condition.