Deep oil and gas reservoirs are under high-temperature conditions,but traditional coring methods do not consider temperature-preserved measures and ignore the influence of temperature on rock porosity and permeability...Deep oil and gas reservoirs are under high-temperature conditions,but traditional coring methods do not consider temperature-preserved measures and ignore the influence of temperature on rock porosity and permeability,resulting in distorted resource assessments.The development of in situ temperaturepreserved coring(ITP-Coring)technology for deep reservoir rock is urgent,and thermal insulation materials are key.Therefore,hollow glass microsphere/epoxy resin thermal insulation materials(HGM/EP materials)were proposed as thermal insulation materials.The materials properties under coupled hightemperature and high-pressure(HTHP)conditions were tested.The results indicated that high pressures led to HGM destruction and that the materials water absorption significantly increased;additionally,increasing temperature accelerated the process.High temperatures directly caused the thermal conductivity of the materials to increase;additionally,the thermal conduction and convection of water caused by high pressures led to an exponential increase in the thermal conductivity.High temperatures weakened the matrix,and high pressures destroyed the HGM,which resulted in a decrease in the tensile mechanical properties of the materials.The materials entered the high elastic state at 150℃,and the mechanical properties were weakened more obviously,while the pressure led to a significant effect when the water absorption was above 10%.Meanwhile,the tensile strength/strain were 13.62 MPa/1.3%and 6.09 MPa/0.86%at 100℃ and 100 MPa,respectively,which meet the application requirements of the self-designed coring device.Finally,K46-f40 and K46-f50 HGM/EP materials were proven to be suitable for ITP-Coring under coupled conditions below 100℃ and 100 MPa.To further improve the materials properties,the interface layer and EP matrix should be optimized.The results can provide references for the optimization and engineering application of materials and thus technical support for deep oil and gas resource development.展开更多
Curing behavior of a model epoxies system (E-54/AG-80) with DDS as hardener was studied in this paper. Round disk compression mode DMA was executed to study the gel behaviors at different temperatures to determine the...Curing behavior of a model epoxies system (E-54/AG-80) with DDS as hardener was studied in this paper. Round disk compression mode DMA was executed to study the gel behaviors at different temperatures to determine the relationship between gel-time (t_ gel) and temperature. The cure kinetics was studied by dynamic DSC analysis. Parameters were obtained for establishing a phenomenological cure reaction model. The relationship between glass transition temperature (T_g) and cure degree (α) was also analyzed by both isothermal and dynamic DSC method based on DiBenedetto equation, which gave a mathematical description of T_g as a function of both time and temperature. Consequently, characteristic temperatures such as T_ g0, gelT_ g and T_ g∞ were determined. Finally, the Time-Temperature-Transition (TTT) diagram was designed based on the data and equations.展开更多
Major defects in forming of conical cups are wrinkles and rupture.Hydrodynamic deep drawing assisted by radial pressure（HDDRP） is a sheet hydroforming process for production of shell cups in one step.In this work,pr...Major defects in forming of conical cups are wrinkles and rupture.Hydrodynamic deep drawing assisted by radial pressure（HDDRP） is a sheet hydroforming process for production of shell cups in one step.In this work,process window diagrams（PWDs） for Al1050-O,pure copper and DIN 1623 St14 steel are obtained for HDDRP process.The PWD is determined to provide a quick assessment of part producibility for sheet hydroforming process.Finite element method is used for this purpose considering the process parameters including pressure path,and the blank material and its thickness.Numerical results are validated by experiments.It is shown that the sheets with less initial thickness and higher strength show better formability and uniformity of thickness distribution on final product.The results demonstrate that the obtained PWD can predict appropriate forming area and probability of rupture or wrinkling occurrence under different pressure loading paths.展开更多
Though Unified Modeling Language (UML) has been widely used in software development, the major problems confronted lie in comprehension and testing. Dependence analysis is an important approach to analyze, understand,...Though Unified Modeling Language (UML) has been widely used in software development, the major problems confronted lie in comprehension and testing. Dependence analysis is an important approach to analyze, understand, test and maintain programs. A new kind of dependence analysis method for UML class diagrams is developed. A set of dependence relations is definedcorresponding to the relations among classes. Thus, the dependence graph of UML class diagram can be constructed from these dependence relations. Based on this model, both slicing and measurement coupling are further given as its two applications.展开更多
基金supported by the Sichuan Science and Technology Program (Grant Nos.2023NSFSC0004,2023NSFSC0790)the National Natural Science Foundation of China (Grant Nos.51827901,52304033)the Sichuan University Postdoctoral Fund (Grant No.2024SCU12093)。
文摘Deep oil and gas reservoirs are under high-temperature conditions,but traditional coring methods do not consider temperature-preserved measures and ignore the influence of temperature on rock porosity and permeability,resulting in distorted resource assessments.The development of in situ temperaturepreserved coring(ITP-Coring)technology for deep reservoir rock is urgent,and thermal insulation materials are key.Therefore,hollow glass microsphere/epoxy resin thermal insulation materials(HGM/EP materials)were proposed as thermal insulation materials.The materials properties under coupled hightemperature and high-pressure(HTHP)conditions were tested.The results indicated that high pressures led to HGM destruction and that the materials water absorption significantly increased;additionally,increasing temperature accelerated the process.High temperatures directly caused the thermal conductivity of the materials to increase;additionally,the thermal conduction and convection of water caused by high pressures led to an exponential increase in the thermal conductivity.High temperatures weakened the matrix,and high pressures destroyed the HGM,which resulted in a decrease in the tensile mechanical properties of the materials.The materials entered the high elastic state at 150℃,and the mechanical properties were weakened more obviously,while the pressure led to a significant effect when the water absorption was above 10%.Meanwhile,the tensile strength/strain were 13.62 MPa/1.3%and 6.09 MPa/0.86%at 100℃ and 100 MPa,respectively,which meet the application requirements of the self-designed coring device.Finally,K46-f40 and K46-f50 HGM/EP materials were proven to be suitable for ITP-Coring under coupled conditions below 100℃ and 100 MPa.To further improve the materials properties,the interface layer and EP matrix should be optimized.The results can provide references for the optimization and engineering application of materials and thus technical support for deep oil and gas resource development.
文摘Curing behavior of a model epoxies system (E-54/AG-80) with DDS as hardener was studied in this paper. Round disk compression mode DMA was executed to study the gel behaviors at different temperatures to determine the relationship between gel-time (t_ gel) and temperature. The cure kinetics was studied by dynamic DSC analysis. Parameters were obtained for establishing a phenomenological cure reaction model. The relationship between glass transition temperature (T_g) and cure degree (α) was also analyzed by both isothermal and dynamic DSC method based on DiBenedetto equation, which gave a mathematical description of T_g as a function of both time and temperature. Consequently, characteristic temperatures such as T_ g0, gelT_ g and T_ g∞ were determined. Finally, the Time-Temperature-Transition (TTT) diagram was designed based on the data and equations.
文摘Major defects in forming of conical cups are wrinkles and rupture.Hydrodynamic deep drawing assisted by radial pressure（HDDRP） is a sheet hydroforming process for production of shell cups in one step.In this work,process window diagrams（PWDs） for Al1050-O,pure copper and DIN 1623 St14 steel are obtained for HDDRP process.The PWD is determined to provide a quick assessment of part producibility for sheet hydroforming process.Finite element method is used for this purpose considering the process parameters including pressure path,and the blank material and its thickness.Numerical results are validated by experiments.It is shown that the sheets with less initial thickness and higher strength show better formability and uniformity of thickness distribution on final product.The results demonstrate that the obtained PWD can predict appropriate forming area and probability of rupture or wrinkling occurrence under different pressure loading paths.
文摘Though Unified Modeling Language (UML) has been widely used in software development, the major problems confronted lie in comprehension and testing. Dependence analysis is an important approach to analyze, understand, test and maintain programs. A new kind of dependence analysis method for UML class diagrams is developed. A set of dependence relations is definedcorresponding to the relations among classes. Thus, the dependence graph of UML class diagram can be constructed from these dependence relations. Based on this model, both slicing and measurement coupling are further given as its two applications.
