Removal of phenol by activated alumina bed in pulsed high-voltage electric field

A new process for removing the pollutants in aqueous solution-activated alumina bed in pulsed high-voltage electric field was investigated for the removal of phenol under different conditions. The experimental results indicated the increase in removal rate with increasing applied voltage, increasing pH value of the solution, aeration, and adding Fe^2＋. The removal rate of phenol could reach 72.1% when air aeration flow rate was 1200 ml/min, and 88.2% when 0.05 mmol/L Fe^2＋ was added into the solution under the conditions of applied voltage 25 kV, initial phenol concentration of 5 mg/L, and initial pH value 5.5. The addition of sodium carbonate reduced the phenol removal rate. In the pulsed high-voltage electric field, local discharge occurred at the surface of activated alumina, which promoted phenol degradation in the thin water film. At the same time, the space-time distribution of gas-liquid phases was more uniform and the contact areas of the activated species generated from the discharge and the pollutant molecules were much wider due to the effect of the activated alumina bed. The synthetical effects of the pulsed high-voltage electric field and the activated alumina particles accelerated phenol degradation.

Study on Surface Electric Field Simulation of High Voltage Transmission Line Assembly

For the studies in the field of high voltage power transmission, this paper has adopted the method of finite element node potential, and put forward two kinds of high pressure sensor-fixture modeling scheme for the sensor-fixture of the high voltage side, the simulation analysis shows that the sensor-fixture surface should be smooth, and should not appear the conclusion of edges and corners. While through establishing the four clamps assembly optimized model, and simulates the strain gages, fixtures and conductor surface field strength and electric field distribution in the model as a whole in turn, this paper Finally got the optimal size of fixture structure and assembly of each part reasonable location layout.

Effects of High-voltage Pulse Electric Field Treatment on the Structure Stability of Konjac Glucomannan

Structures of KGM treated in two high-voltage pulse electric fields were characterized by infrared spectroscopy,Raman spectroscopy,X-ray diffraction and so on.The results showed that intermolecular hydrogen bonding interactions of KGM were reduced after being treated with high-voltage pulse electric field,but there was no significant effect on its fiber chain form and thermal characteristics.Results of the study can provide a useful reference for further study on the structure and property of KGM,and especially can provide theoretical basis for the effect of physical field on the foodstuff deep processing related to KGM.

New Breakdown Electric Field Calculation for SF6 High Voltage Circuit Breaker Applications

The critical electric fields of hot SF6 are calculated including both electron and ion kinetics in wide ranges of temperature and pressure, namely from 300 K up to 4000 K and 2 atmospheres up to 32 atmospheres respectively. Based on solving a multi-term electron Boltz- mann equation the calculations use improved electron-gas collision cross sections for twelve SF6 dissociation products with a particular emphasis on the electron-vibrating molecule interactions. The ion kinetics is also considered and its role on the critical field becomes non negligible as the temperature is above 2000 K. These critical fields are then used in hydrodynamics simulations which correctly predict the circuit breaker behaviours observed in the case of breaking tests.

Structure Design and Properties of Three-Layer Particleboard Based on High Voltage Electrostatic Field(HVEF)

In this study,the effects of three different particle sizes of wood wastes(A=–8+12 mesh;B=–12+20 mesh;C=–20+30 mesh)and factory shavings(D)on the properties of particleboard were investigated.According to the test results,three-layer particleboard was designed.Particleboard face layers made with mixture of A,B,and C.The core layer made with D.The ratio of core layer to face layers is 50:50.Three-layer particleboard were fabricated with 12%urea-formaldehyde(UF)resins and three different high voltage electrostatic field intensities(0 kv,30 kv,60 kv).The internal bond(IB)strength,modulus of rupture(MOR),modulus of elasticity(MOE),thickness swelling(TS),and water absorption(WA)of particleboard were evaluated.The density distribution of the three-layer particleboard were examined by vertical density profiles(VDP),and the bonding mechanism and functional groups changes in the particles were analyzed by FTIR analysis.The results showed that HVEF treatment intensity play a remarkable role in properties of particleboard.The particleboard with higher electrostatic field intensities treatment has higher MOE,MOR,IB,and TS.Under HVEF treatment(60 kv),the MOR,modulus of MOE,and IB of three-layer particleboard were 23.61 N/mm^(2),2787.09 N/mm^(2),and 0.86 N/mm^(2),respectively.FTIR indicated that the surface activity of wood particles was increased electric field treatment.

Hydrophobic Poplar Prepared via High Voltage Electric Field(HVEF)with Copper as Electrode Plate

In order to improve hydrophobic characteristics which will affect the service performance of fast-growing poplar due to growing bacteria in the humid environment.In this study,a simple method was proposed to treat poplar via the high voltage electric field(HVEF)with copper as the electrode plate.Scanning electron microscope(SEM),Fourier transforms infrared spectroscopy(FTIR),X-ray diffraction(XRD)and contact angle tester were adopted to evaluate the surface morphology,surface group of poplar,crystallinity and wettability under HVEF.It was found by SEM that a large number of copper particles were uniformly attached to the surface of poplar.In all three sections,the weight percentage of the Cu element was accounting for more than half.The diffraction peaks of copper-containing compounds appeared in the(XRD).FTIR analysis confirmed that the reaction between copper and poplar took place.The surface contact angle of three sections of poplar increased in the following order:cross section<radial section<tangential section(increased by 34°,45°and 53°,respectively).An environmentfriendly and efficient method of HVEF treating fast-growing wood with copper as the electrode plate can promote its outdoor application.

A new analytical model of high voltage silicon on insulator(SOI) thin film devices

A new analytical model of high voltage silicon on insulator （SOI） thin film devices is proposed, and a formula of silicon critical electric field is derived as a function of silicon film thickness by solving a 2D Poisson equation from an effective ionization rate, with a threshold energy taken into account for electron multiplying. Unlike a conventional silicon critical electric field that is constant and independent of silicon film thickness, the proposed silicon critical electric field increases sharply with silicon fihn thickness decreasing especially in the case of thin films, and can come to 141V/μm at a film thickness of 0.1 μm which is much larger than the normal value of about 30 V/μm. From the proposed formula of silicon critical electric field, the expressions of dielectric layer electric field and vertical breakdown voltage （VB,V） are obtained. Based on the model, an ultra thin film can be used to enhance dielectric layer electric field and so increase vertical breakdown voltage for SOI devices because of its high silicon critical electric field, and with a dielectric layer thickness of 2 μm the vertical breakdown voltages reach 852 and 300V for the silicon film thicknesses of 0.1 and 5μm, respectively. In addition, a relation between dielectric layer thickness and silicon film thickness is obtained, indicating a minimum vertical breakdown voltage that should be avoided when an SOI device is designed. 2D simulated results and some experimental results are in good agreement with analytical results.

Measurement of Breakdown Electric Field Strength for Vegetation and Hydrocarbon Flames

A significant number of fire-induced power disruptions are observed in several countries every year. The faults are normally phase-to-phase short circuiting or conductor-to-ground discharges at mid-span region of the high-voltage transmission system. In any case, the wildfire plumes provide a conductive path. The electrical conductivity is due to intense heat in combustion zone of the fire which creates ion and electrons from flame inherent particulates. Increase in the ion concentration increases the electrical conductivity of the fire plume. The main purpose of this study was to measure dielectric breakdown electric field for vegetation and hydrocarbon flames. The experimental data is needed for validation of simulation schemes which are necessary for evaluation of power grid systems reliability under extreme wildfire weather conditions. In this study, hydrocarbon and vegetation fuels were ignited in a cylindrically shaped steel burner which was fitted with type-K thermocouples to measure flame temperature. The fuels consisted of dried weeping wattle (Peltophorum africanum) litter, butane gas and candle wax. Two pinned copper electrodes supported by retort stands were mounted to the burner and energized to a high voltage. This generated a strong electric field sufficient to initiate dielectric breakdown in the flames. Breakdown electric field strength (Ecrit) obtained from the experiment decreased from 10.5 to 6.9 kV/cm for the flames with temperature range of 1003 to 1410 K, respectively.

Impact of Ion Current on Total Electric Field Measurement Under HVDC Transmission Line

The total electric field(TEF) at ground level induced by high-voltage direct current(HVDC) overhead transmission lines is one of the important indexes for evaluating the lines' electromagnetic environment.Based on analyzing the existing TEF sensors and the measurement principle of ion-current density,the influence from ions on TEF measurements is quantitively studied.The results show that the ions generated by the corona from a HVDC transmission line in operation cause errors in the measurement of TEF.This error is determined through analyzing the component of total measuring current on the filed mill's sensing electrode: if no appropriate approach taken,the maximum measurement error reaches up to 4.3%.Furthermore,a method that can eliminate such error,and hence improve the accuracy of TEF sensors is designed.

干燥空气绝缘开关柜中应用的固封极柱绝缘结构设计及优化

为了实现气体绝缘开关柜的绝缘介质由SF6向干燥空气等环保型气体转变,开发一种结构小型化、绝缘水平满足要求的干燥空气绝缘开关柜中使用的固封极柱是亟需解决的问题。文中分析了40.5 kV SF6固封极柱置于干燥空气绝缘开关柜中的相间及对地电场分布,结果显示灭弧室动、静端盖板以及绝缘拉杆附近的气—固沿面电场严重超标,易造成沿面闪络。依据气—固复合绝缘理论,采取增加均压屏蔽网、改进绝缘壳体外观结构、重新设计绝缘拉杆等措施进行电场优化。通过仿真分析,优化设计后的固封极柱灭弧室端盖附近沿面最大场强由3.4 kV/mm降至2.03 kV/mm,绝缘拉杆沿面最大场强由4.1 kV/mm降至1.7 kV/mm。对优化前后的固封极柱进行了局部放电和雷电冲击耐压试验,局部放电试验的起弧电压由35 kV提升到62 kV,雷电冲击耐压试验的峰值耐受电压由145 kV提升到218 kV,证明了优化方案的可行性,为后续40.5 kV及更高电压等级的类似固封极柱的研发及优化提供了有关参考。

An Analysis of Magnetic Field Environment Near High-Voltage Power Lines and Contact Wires of Electric Railways

Image method is used in this paper to calculate the value of magnetic field near high-voltage transmission lines and electric railways. Areas in which the magnetic field is less than 0.002 Gauss are given and the magnetic pollution of high-voltage power transmission lines and electric railways is discussed

高压开关柜故障起火自动灭火装置优化设计研究

近年来发生了多起高压开关柜火灾事故,传统开关柜灭火通过人工方式灭火,存在灭火效率低、人员风险大等问题。现有开关柜自动灭火装置研究存在引入电场畸变、启动阈值不清及灭火剂选择不当等问题。为解决上述问题,文中开展了高压开关柜故障起火自动灭火系统研究。优化设计了了灭火剂喷头结构,降低了最大场强,避免了绝缘击穿风险。进行了真型开关柜火灾模拟试验,基于试验过程中温度场分布确定了灭火装置启动阈值。探索了灭火剂类型与用量,确定了合理的高压开关柜灭火剂设置方案。建立了完整的高压开关柜自动灭火系统,试验结果表明文中所提出灭火系统快速有效。

高压电场选育高产酸性木聚糖酶菌株的研究

为获得适用于动物饲料的木聚糖酶高产菌株,并验证高压电场诱变方法的有效性,于农田土壤中筛选出高产菌株,在高压电场中进行诱变,筛选最佳的突变菌株。出发菌株初步鉴定为沙福芽孢杆菌,命名为Bacillus safensis B16。该菌株所产木聚糖酶在pH 5、60℃下酶活性为217.34 U/mL,且60℃时的半衰期为229 min,热稳定性良好。在6~24 kV、极间距为3 cm的高压电晕电场中处理0~10 min,最终在10 kV下处理6 min选育出一株木聚糖酶高产菌株B16106-2,酶活性达到256.73 U/mL,较出发菌株提升了18.12%,且传代7次后菌株的产酶能力基本不变,具有良好的遗传稳定性。突变菌株所产木聚糖酶的最适酶反应条件不变。研究证明,高压电晕电场是一种有效的诱变方式,且筛选出的菌株B16106-2性能良好。

金属罐体对真空灭弧室内部电场分布的影响

利用真空开断技术以及环保气体绝缘技术开发罐式真空断路器是高压真空断路器的一个重要发展方向。为此,建立了126 kV单断口真空灭弧室以及罐式断路器的电场仿真模型,分别从触头表面电场分布、触头间隙有效击穿面积以及内部电场分布对称性三个方面,探究了布置在金属罐中的真空灭弧室内部电场的变化。结果表明,金属罐体引起真空灭弧室内部动、静两侧的电场分布不对称,出现高电位侧电场强度增大,而低电位侧电场强度减小的情况。针对这一情况,建立等效电路模型,从电路层面分析。结果表明,对地杂散电容增大引起了主屏蔽罩的电位降低。进一步地,通过将主屏蔽罩电位设置为一系列的固定值,研究了主屏蔽罩电位对于真空灭弧室内部电场分布的影响。当控制主屏蔽罩电位相同时,布置在金属罐中的真空灭弧室与单个真空灭弧室相比,两者内部电场分布基本一致,这为罐式断路器中的真空灭弧室内部电场的优化提供了参考。

高压脉冲电场对毛发染色效果的影响

为了研究高压脉冲电场对毛发染色效果的影响,试验以18~28岁年龄段人群的黑色头发和染发剂为试材,以染发后毛发的RGB(red green blue)模型提取值作为响应值,并采用等响应面试验法设计试验,以构建和分析高压脉冲电场的电场强度、脉冲宽度以及脉冲个数对毛发染色效果影响的数学模型和机理。试验结果表明:高压脉冲电场同时处理头发和染发剂后最高可提升RGB参数中的蓝色通道值B为3.7%,对应的最优化工艺化参数为:电场强度1125 V/mm、脉冲宽度175μs、脉冲个数52个。因此,高压脉冲电场对头发和染发剂进行处理后再进行染色可改善着色效果,并为毛发染色工艺优化奠定一定基础。

高海拔地区18 kV水轮发电机定子绕组端部防晕技术研究

为满足海拔高度为2 500 m的某大型水电站18 kV水轮发电机的防晕要求,本文从理论方面分析了目标海拔高度下的空气击穿场强及影响因素,并通过建立定子绕组端部三维仿真模型评估了端部电场特性,分析了间隙距离与绑扎结构对端部斜边电场的影响,确定了定子绕组端部斜边最小间隙距离控制在15 mm的方案。最后,在构建的大型高海拔环境模拟试验室完成了18 kV水轮发电机定子线圈和绕组的防晕性能进行测试验证。结果表明:该18 kV水轮发电机的防晕性能良好,满足在2 500 m海拔高度下的防晕要求。

基于合成场强仪的输电工程地面合成电场研究

高压直流(DC)输电线路交叉跨越是我国特高压(UHV)技术发展中出现的问题。由于两回DC线路相互影响,交叉跨越区域内合成电场呈复杂的三维分布,UHV DC输电工程地面合成电场计算较为困难。选取典型±800 kV UHV DC输电工程进行地面合成电场的实测研究。参照GB 39220—2020,采用HDEM-01合成场强仪进行野外现场实测。测量参数为有效期内的场磨传感器上积聚的电荷量。测量结果与运行初期实测数据的对比结果表明:±800 kV换流站周边运行初期合成电场强度略低于后期,且整体水平较低;沿线电磁环境敏感目标运行初期、后期的实测数据中,74%的数值小于5 kV/m。通过此次研究,明确了UHV DC输电工程合成电场不同时期的特性。该研究有助于推进UHV DC输电工程的快速建成,并提高其运行安全性,从而推动电力工程建设的发展。

零值绝缘子对超高压500 kV绝缘子串电场分布影响研究

作为超高压输电线路的关键部件绝缘子长期运行后其绝缘性能下降,容易产生零值绝缘子,严重时会造成经济损失。因此,利用有限元方法研究不同位置和数量的零值绝缘子对超高压500 kV绝缘子串电场分布的影响。结果表明:存在零值绝缘子以及零值绝缘子的位置和数量均会对绝缘子串的电场分布产生一定的影响,高低压端存在零值绝缘子对绝缘子串电场影响最大。且当监测路径不同时,零值绝缘子对于绝缘子电场分布的影响会存在变化。零值绝缘子数量会对电场值影响程度有所改变。最后试验与理论结果对比显示,理论值与试验值在可接受范围之内存在一定的误差。

高压电能计量现场校准装置及其不确定度分析

随着新建产能增加和新技术的不断应用,油田用电量逐渐增大,对高压电能计量设备进行科学的评价,可以对设备运行情况提供可靠的数据支持,以节省和减少油田的能源消耗,进而为设备维护更新、技术改造、新建项目等提供决策支持。高压电能计量现场校准装置,采用高压三相标准功率源和多功能标准表、V/V转换器、I/V转换器组合的方式对高压电能计量设备进行整体校准,对装置进行不确定度分析,使装置在现场校准的过程中能够保持稳定的性能指标。