Optimisation of Electrical Distribution System by Using Solar Thermal Powered Systems and Its Impact on Electrical Distribution Feeders

In this research, the performance of the solar thermal powered systems (STPS) is analyzed with different models (without inserts, with inserts and with Nano fluids with different concentrations) and its impact on the Electric load in a residential/Institutional Electrical Distribution system. For this purpose, the electrical and solar thermal water heater is tested and validated. Solar thermal powered systems and its impact on the Institutional electrical distribution feeders are tested and compared with the energy efficiency (EE) and cost optimization. The goal of this paper is to analyze the impact of solar thermal energy on electrical energy consumption in the electrical distribution feeder level. The electrical system cost and energy consumptions are tabulated and observed that there is a considerable savings.

NOVEL AIRCRAFT ELECTRICAL POWER DISTRIBUTION SYSTEM BASED ON DISTRIBUTED COMPUTER

As a matured technique used in many fields,the distributed computer system is still a new management method for the aeronautical electrical power distribution system in our country. In this paper, a novel aircraft electrical power distribution system based on the distributed computer system is proposed. The principles, features and structure of the aircraft electrical power distribution system and the distributed computer system named electrical load management system (ELMS) are studied. The ELMS composed of four electrical load management centers (ELMCs) and two power source processors (PSPs) operates in the 1553B buses. Principles of the ELMCs and the PSPs are introduced. With the application of the distributed computer system, the aircraft electrical power distribution system is simple, adaptable and flexible.

A Novel Analytical Model for Surface Electrical Field Distribution and Optimization of TFSOI RESURF Devices

A novel analytical model for the thin film silicon on insulator (TFSOI) reduced surface field (RESURF) devices has been proposed.Based on the 2-D Poisson equation solution,the analytical expressions for the surface potential and field distributions are derived.From this analysis,the optimum design condition for the maximum breakdown voltage is obtained.The dependence of the maximum breakdown voltage on the drift region length is examined and the relationship between the critical doping concentration and the front- and back- interface oxide layer thickness is discussed.The numerical simulation performed by the advanced semiconductor simulation tool,DESSIS-ISE,has been shown to support the analytical results.

Optimal allocation of solar photovoltaic distributed generation in electrical distribution networks using Archimedes optimization algorithm

This paper proposes to resolve optimal solar photovoltaic(SPV)system locations and sizes in electrical distribution networks using a novel Archimedes optimization algorithm(AOA)inspired by physical principles in order to minimize network dependence and greenhouse gas(GHG)emissions to the greatest extent possible.Loss sensitivity factors are used to predefine the search space for sites,and AOA is used to identify the optimal locations and sizes of SPV systems for reducing grid dependence and GHG emissions from conventional power plants.Experiments with composite agriculture loads on a practical Indian 22-bus agricultural feeder,a 28-bus rural feeder and an IEEE 85-bus feeder demonstrated the critical nature of optimally distributed SPV systems for minimizing grid reliance and reducing GHG emissions from conventional energy sources.Additionally,the voltage profile of the network has been enhanced,resulting in significant reductions in distribution losses.The results of AOA were compared to those of several other nature-inspired heuristic algorithms previously published in the literature,and it was observed that AOA outperformed them in terms of convergence and redundancy when solving complex,non-linear and multivariable optimization problems.

A Multi-Criteria Optimization Method for Electrical Distribution System and Its Analysing in Practice

In this paper, the author explains the problem that we have to consider multiple goals and multiple factors which are usually affected by others at the same time in practical work for electrical power distribution system programming. A new mathematics model is set up here for the multiple goals programming of electrical power distribution system which includes various load control alternatives. An arithmetic and current software for the multi-criteria optimization of electrical power distribution system are given here. The author calculates and analyses the optimal programming projects and the optimal operation strategies for a practical system, which show that the model, the arithmetic and the current software are all correct and effective. The outcome of researches has been adopted by the authoritative persons.

Power Distribution System Regulation (A Review)

This article presents a framework and a comprehensive model to optimize the regulation of the electricity distribution system.The regulatory requirements of the electricity distribution system and research gaps in this field are among the important outputs of this review article.In each of the presented parts of the framework,it has reviewed,introduced and listed the regulatory studies of the electricity distribution system.In order to calculate the PDSR(regulation of power distribution system)framework,governance first presents,its goals,and its development plan in the distribution sector,and discusses the regulatory position in it.After that,in the electricity distribution system,it describes the role of the regulator in the goals and plans of the electricity distribution system,and introduces the types of regulation of the electricity distribution system,and finally,discusses about the place of data in the regulation and its requirements,and the effects of regulation in the evolution and stability of the electricity distribution system.

Influence of non-uniform electric field distribution on the atmospheric pressure air dielectric barrier discharge

The dielectric barrier discharge(DBD)in air at atmospheric pressure is not suitable for industrial applications due to its randomly distributed discharge filaments.In this paper,the influence of the electric field distribution on the uniformity of DBD is theoretically analyzed and experimentally verified.It is found that a certain degree of uneven electric field distributions can control the development of electron avalanches and regulate their transition to streamers in the gap.The discharge phenomena and electrical characteristics prove that an enhanced Townsend discharge can be formed in atmospheric-pressure air with a curved-plate electrode.The spectral analysis further confirms that the gas temperature of the plasma produced by the curved-plate electrode is close to room temperature,which is beneficial for industrial applications.This paper presents the relationship between the electron avalanche transition and the formation of a uniform DBD,which can provide some references for the development and applications of the DBD in the future.

Multi-objective planning model for simultaneous reconfiguration of power distribution network and allocation of renewable energy resources and capacitors with considering uncertainties

This research develops a comprehensive method to solve a combinatorial problem consisting of distribution system reconfiguration, capacitor allocation, and renewable energy resources sizing and siting simultaneously and to improve power system's accountability and system performance parameters. Due to finding solution which is closer to realistic characteristics, load forecasting, market price errors and the uncertainties related to the variable output power of wind based DG units are put in consideration. This work employs NSGA-II accompanied by the fuzzy set theory to solve the aforementioned multi-objective problem. The proposed scheme finally leads to a solution with a minimum voltage deviation, a maximum voltage stability, lower amount of pollutant and lower cost. The cost includes the installation costs of new equipment, reconfiguration costs, power loss cost, reliability cost, cost of energy purchased from power market, upgrade costs of lines and operation and maintenance costs of DGs. Therefore, the proposed methodology improves power quality, reliability and security in lower costs besides its preserve, with the operational indices of power distribution networks in acceptable level. To validate the proposed methodology's usefulness, it was applied on the IEEE 33-bus distribution system then the outcomes were compared with initial configuration.

Electron beam modeling and analyses of the electric field distribution and space charge effect

In electron beam technology, one of the critical focuses of research and development efforts is on improving the measurement of electron beam parameters. The parameters are closely related to the generation, emission, operation environment, and role of the electron beam and the corresponding medium. In this study, a field calculation method is proposed, and the electric field intensity distribution on the electron beam’s cross-section is analyzed. The characteristics of beam diffusion caused by the space charge effect are investigated in simulation, and the obtained data are compared with the experiment. The simulation demonstrated that the cross-sectional electric field distribution is primarily affected by the electron beam current, current density distribution, and electron beam propagation speed.

Electric field distribution and effective nonlinear AC and DC responses of graded cylindrical composites

The perturbation method is used to study the localization of electric field distribution and the effective nonlinear response of graded composites under an external alternating-current（AC） and direct-current（DC） electric field E app = E 0（1 ＋ sin ωt）.The dielectric profile of the cylindrical inclusions is modeled by function ε i（r） = C k r k（r ≤ a）,where r is the radius of the cylindrical inclusion,and C k,k,a are parameters.In the dilute limit,the local potentials and the effective nonlinear responses at all harmonics are derived.Meanwhile,the general effective nonlinear responses are also derived and compared with the effective nonlinear responses at harmonics under the AC and DC external field.It is found that the effective nonlinear AC and DC responses at harmonics can be calculated by those of the general effective nonlinear of the graded composites under the external DC electric field.Moreover,the obtained local electrical fields show that the electrical field distribution in the cylindrical inclusions is controllable,and the maximum of the electric field inside the cylinder is at its center.

Global Harmonic Rate Assessment in the Electricity Distribution Network in Niamey City:Case Studies of Domestic,Industrial and Hospital Substations

Like others countries of the world, in Niger also, we are witnessing an increasing use of non-linear electric loads in the domestic, hospital and industrial sectors. However, these loads degrade the shape of the electrical signal and cause disastrous effects to the equipment of the distribution system and the devices which are connected to the network. This article highlights the presence of electric harmonics in the distribution network in Niamey city. In order to do this, measurements were taken at the secondary level of the substations using an energy quality analyze r (FLUKE 1735). By using this measuring instrument, we quantified the voltage and current Total Harmonic Distortion (THD) in the three substations. The results obtained show that, although the statutable rates set by the standards are not exceeded for phase conductors, the neutral contains a very critical percentage of distortion on the residential and hospital substations. Moreover, this assessment made it possible to observe the variation of harmonics in the presence of voltage drops.

Twin boundary dominated electric field distribution in CdZnTe detectors

The performance of CdZnTe X/γ-ray detectors is strongly affected by the electric field distribution in terms of charge transport and charge collection.Factors which determine the electric field distribution are not only electric contact,but also intrinsic defects,especially grown-in twin boundaries.Here,the electric field distribution around twin boundaries is investigated in a CdZnTe bicrystal detector with a{111}–{111}twin plane using the Pockels electro-optic effect.The results of laser beam induced current pulses are also obtained by the transient current technique,and we discuss the influence of the twin boundary on the electric field evolution.These studies reveal a significant distortion of the electric field,which is attributed to the buildup of space charges at twin boundaries.Also,the position of these space charge regions depends on the polarity of the detector bias.An energy band model based on the formation of an n–n+–n junction across the twin boundary has been established to explain the observed results.

Electric field distribution around the chain of composite nanoparticles in ferrofluids

Composite nanoparticles （NPs） have the ability of combining materials with different properties together, thus receiving extensive attention in many fields. Here we theoretically investigate the electric field distribution around core/shell NPs （a type of composite NPs） in ferrofluids under the influence of an external magnetic field. The NPs are made of cobalt （ferromagnetic） coated with gold （metallic）. Under the influence of the external magnetic field, these NPs will align along the direction of this field, thus forming a chain of NPs. According to Laplace＇s equations, we obtain electric fields inside and outside the NPs as a function of the incident wavelength by taking into account the mutual interaction between the polarized NPs. Our calculation results show that the electric field distribution is closely related to the resonant incident wavelength, the metallic shell thickness, and the inter-particle distance. These analytical calculations agree well with our numerical simulation results. This kind of field-induced anisotropic soft-matter systems offers the possibility of obtaining an enhanced Raman scattering substrate due to enhanced electric fields.

Electric potential distribution near nanocone arrays on metal substrates

Based on the nanostructured surface model,where conical nanoparticle arrays grow out symmetrically from a plane metal substrate,a theoretical model of the local electric potential near nanocones is built when a uniform external electric field is applied.In terms of this model,the electric potential distribution near the nanocone arrays is obtained and given by a curved surface using a numerical computation method.The computational results show that the electric potential distribution near the nanocone arrays exhibit an obvious geometrical symmetry.These results could serve as a basis for explaining many abnormal phenomena,such as the abnormal infrared effects（AIREs） which are found on nanostructured metal surfaces,as well as a reference for investigating the applications of nanomaterials,such as nanoelectrodes and nanosensors.

Influence of the channel electric field distribution on the polarization Coulomb field scattering in In_(0.18) Al_(0.82) N/AlN/GaN heterostructure field-effect transistors

By making use of the quasi-two-dimensional （quasi-2D） model, the current-voltage （l-V） characteristics of In0AsA10.82N/A1N/GaN heterostructure field-effect transistors （HFETs） with different gate lengths are simulated based on the measured capacitance-voltage （C-V） characteristics and I-V characteristics. By analyzing the variation of the electron mobility for the two-dimensional electron gas （2DEG） with electric field, it is found that the different polarization charge distributions generated by the different channel electric field distributions can result in different polarization Coulomb field scatterings. The difference between the electron mobilities primarily caused by the polarization Coulomb field scatterings can reach up to 1522.9 cm2/V.s for the prepared In0.38AI0.82N/A1N/GaN HFETs. In addition, when the 2DEG sheet density is modulated by the drain-source bias, the electron mobility presents a peak with the variation of the 2DEG sheet density, the gate length is smaller, and the 2DEG sheet density corresponding to the peak point is higher.

Modeling porous structure of oil-pressboard interface and its effect on electric field distribution

The oil-pressboard insulation is a typical composite insulation system widely used in the design and manufactory of large power apparatus. The implement of oil-pressboard insulation may lead to surface electrification and discharge at the interface under certain condition. It is of significant importance to take an insight into the phenomenon occurring at the interface. Through experiment, the pressboard is found as a porous material. The interface changes abruptly from bulk pressboard to the bulk oil as a result of the porous structure. A new model is proposed which divides the interface into bulk oil region, transition region, and bulk pressboard region. The width of the transition region is decided according to the microtome figure. The effective permittivity of the transition region is calculated using a new model based on fractal theory. The model is validated and compared with previous calculation model. The effect of the existence of transition region on the electric field distribution is discussed.

Questionnaire Survey of Services and Outsourcing in Finnish Distribution Companies

The aim of this study was to find out what types of services Finnish distribution companies were purchasing and what is the future trend related to them. Results were gathered from Finnish distribution companies using questionnaire. Theoretical background was collected from literacy to get more information of benefits and risks. Results indicate that purchasing services especially from independent service providers is increasing. Also the benefits are greater than the risks related to service purchasing.

Determining the Boundary of Molten Electrolyte and Aluminum in Electrolytic Cells by Detecting Their Vertical Distribution of Potential

Aluminum production is a high energy consumption process so that maintaining fundamental compositions in balance and optimal conditions are essential.The molten electrolyte and melted aluminum are primary materials and their boundary needs to be monitored from time to time.An automatic measurement technic is presented in the paper to substitute for the traditional manual measurement work that is dull,poor efficiency and dangerous for operators.The boundary forming mechanism is analyzed,the vertical profile of electric potential is simulated,an automatic instrument is developed to sense the potential distribution,and a strategy is provided to identify the boundary according to the potential curves.Finally,some practical results are compared with manual measurements,which shows good consistency.

Development and Implementation of GSM-Based Distribution Automation System with Graphic User Interface in Nigeria Electric Power Distribution Network

Lack of up-to-date information on efficient operation and maintenance of EPDS （electric power distribution systems）, Nigeria is addressed by designing and implementing an indigenous real-time monitoring and diagnosis system. The system encompasses the development of software driven hardware positioned at the remotely located sub-stations at the low voltage level to keep track of the network in real-time. The detection of faults exploits threshold passing algorithm through continuous monitoring of the network power quality. Communication between the RTU （remote terminal unit） and the DCC （distribution control center） which is based on GSM is initiated by disturbance. The DCC performs fault evaluation processing using the received data and predetermined faults signatures to determine the nature of disturbance and presents the result in graphic user interface environment. A fault reporting time of 2 s was achieved. The developed system exhibits a high degree of accuracy and manifests no spurious reports during testing. The resultant system limits the effects of interruption and increases power availability by reducing the down time. The system strengthens engineering and management capabilities required to enhance reliability by providing information about the network health status.

Optimization of the Placement and Size of Photovoltaic Source

This paper presents a new optimization study of the placement and size of a photovoltaic source(PVS)in a distribution grid,based on annual records of meteorological parameters(irradiance,temperature).Based on the recorded data,the production output as well as the daily average power(24-h vector)of the PVS is extracted over the year.When a power vector is available,it can be used as an input when searching for the optimal size of the PVS.This allows to take into account the constraint of the variation of the power generated by this source considering the variation of the power consumed by the electrical loads during the whole day.A multi-objective fitness function has been considered.The latter minimizes the active losses and maximizes the voltage stability index during the day,while considering the constraints of the system,that is,the security,technical,geographical,and meteorological constraints.This problem was solved using the Non-dominated Sorting Genetic Algorithm NSGA-II optimization technique under MATLAB 2021.It was applied to the distribution network of Ghardaïa of 59 nodes.