Structure and electrical properties of polysilicon films doped with ammonium tetraborate tetrahydrate

Here,p-type polysilicon films are fabricated by ex-situ doping method with ammonium tetraborate tetrahydrate(ATT)as the boron source,named ATT-pPoly.The effects of ATT on the properties of polysilicon films are comprehensively analyzed.The Raman spectra reveal that the ATT-pPoly film is composed of grain boundary and crystalline regions.The preferred orientation is the(111)direction.The grain size increases from 16−23 nm to 21−47 nm,by~70%on average.Comparing with other reported films,Hall measurements reveal that the ATT-pPoly film has a higher carrier concentration(>10^(20)cm^(−3))and higher carrier mobility(>30 cm2/(V·s)).The superior properties of the ATT-pPoly film are attributed to the heavy doping and improved grain size.Heavy doping property is proved by the mean sheet resistance(Rsheet,m)and distribution profile.The R_(sheet,m)decreases by more than 30%,and it can be further decreased by 90%if the annealing temperature or duration is increased.The boron concentration of ATT-pPoly film annealed at 950℃ for 45 min is~3×10^(20)cm^(−3),and the distribution is nearly the same,except near the surface.Besides,the standard deviation coefficient(σ)of Rsheet,m is less than 5.0%,which verifies the excellent uniformity of ATT-pPoly film.

Magnetic and electrical transport properties in GdAlSi and SmAlGe

We conduct a detailed examination of the magnetic and electrical transport properties in GdAlSi and SmAlGe crystals,which possess a LaPtSi-type structure(space group I4_(1)md).The magnetic susceptibility data unambiguously reveal magnetic ordering below a characteristic transition temperature(T_(N)).For GdAlSi,a hysteresis loop is observed in the magnetization and magnetoresistance curves within the ab plane when the magnetic field is applied below T_(N),which is around32 K.Notable specific heat anomalies are detected at 32 K for GdAlSi and 6 K for SmAlGe,confirming the occurrence of magnetic transitions.In addition,the extracted magnetic entropy at high temperatures is consistent with the theoretical value of Rln(2J+1) for J=7/2 in Gd^(3+) and J=5/2 in Sm^(3+),respectively.SmAlGe also exhibits Schottky-like specific heat contributions.Additionally,both GdAlSi and SmAlGe exhibit positive magnetoresistance and a normal Hall effect.

Electrical and nonlinear optical properties of TGZO transparent conducting films deposited by magnetron sputtering

Thin transparent oxide conducting films(TCOFs)of titanium and gallium substituted zinc oxide(TGZO)were fabricated via radio frequency(RF)magnetron sputtering technique.The effects of RF power on electrical,linear and nonlinear optical characteristics were investigated by Hall tester,Ultraviolet(UV)-visible spectrophotometer and optical characterization method.The results indicate that RF power significantly influences the electrical and optical properties of the deposited films.As RF power raises,the resistivity and Urbach energy fall initially and then rise,while the figure of merit,mean visible transmittance and optical bandgap show the reverse variation trend.At RF power of 190 W,the TGZO sample exhibits the highest electro-optical properties,with the maximum figure of merit(1.14×10^(4)Ω^(-1)∙cm^(-1)),mean visible transmittance(86.9%)and optical bandgap(3.50 eV),the minimum resistivity(6.26×10^(-4)Ω∙cm)and Urbach energy(174.23 meV).In addition,the optical constants of the deposited films were determined by the optical spectrum fitting method,and the RF power dependence of nonlinear optical properties was studied.It is observed that all the thin films exhibit normal dispersion characteristics in the visible region,and the nonlinear optical parameters are greatly affected by the RF power in the ultraviolet region.

Mechanical and Electrical Properties of Some Sn-Zn Based Lead-Free Quinary Alloys

Although there are many lead-free soldering alloys on the market, none of them have ideal qualities. The researchers are combining binary alloys with a variety of additional materials to create the soldering alloys’ features. The eutectic Sn-9Zn alloy is among them. This paper investigated the mechanical and electrical properties of Sn-9Zn-x (Ag, Cu, Sb);{x = 0.2, 0.4, and 0.6} lead-free solder alloys. The mechanical properties such as elastic modulus, ultimate tensile strength (UTS), yield strength (YS), and ductility were examined at the strain rates in a range from 4.17 10−3 s−1 to 208.5 10−3 s−1 at room temperature. It is found that increasing the content of the alloying elements and strain rate increases the elastic modulus, ultimate tensile strength, and yield strength while the ductility decreases. The electrical conductivity of the alloys is found to be a little smaller than that of the Sn-9Zn eutectic alloy.

Molecular simulation study of the microstructures and properties of pyridinium ionic liquid[HPy][BF_(4)]mixed with acetonitrile

The microstructures and thermodynamic properties of mixed systems comprising pyridinium ionic liquid[HPy][BF_(4)]and acetonitrile at different mole fractions were studied using molecular dynamics simulation in this work.The following properties were determined:density,self-diffusion coefficient,excess molar volume,and radial distribution function.The results show that with an increase in the mole fraction of[HPy][BF_(4)],the self-diffusion coefficient decreases.Additionally,the excess molar volume initially decreases,reaches a minimum,and then increases.The rules of radial distribution functions(RDFs)of characteristic atoms are different.With increasing the mole fraction of[HPy][BF_(4)],the first peak of the RDFs of HA1-F decreases,while that of CT6-CT6 rises at first and then decreases.This indicates that the solvent molecules affect the polar and non-polar regions of[HPy][BF_(4)]differently.

Effect of Zr and Sc on mechanical properties and electrical conductivities of Al wires

In order to obtain the Al wires with good mechanical properties and high electrical conductivities, conductive wires of Al-0.16 Zr, Al-0.16 Sc, Al-0.12Sc-0.04Zr（mass fraction, %） and pure Al（99.996%） were produced with the diameter of 9.5 mm by continuous rheo-extrusion technology, and the extruded materials were heat treated and analyzed. The results show that the separate additions of 0.16% Sc and 0.16% Zr to pure Al improve the ultimate tensile strength but reduce the electrical conductivity, and the similar trend is found in the Al-0.12Sc-0.04 Zr alloy. After the subsequent heat treatment, the wire with the optimum comprehensive properties is Al-0.12Sc-0.04 Zr alloy, of which the ultimate tensile strength and electrical conductivity reach 160 MPa and 64.03%（IACS）, respectively.

Enhanced thermal and electrical properties of poly (D,L-lactide)/ multi-walled carbon nanotubes composites by in-situ polymerization

Biodegradable poly （D,L-lactide） （PLA）/carboxyl-functionalized multi-walled carbon nanotubes （c-MWCNTs） composites were achieved via in-situ polymerization. These as-prepared composite materials were characterized with FT-IR, XRD, TG, DSC, SEM, and high insulation resistance meter. The results demonstrate that the multi-walled carbon nanotube was carboxyl functionalized, which improved the collection between c-MWCNTs and PLA, and further realized the graft copolymerization of c-MWCNTs and PLA. There is a higher glass transition temperature and a lower pyrolysis temperature of PLA/c-MWCNTs composites than pure PLA. The c-MWCNTs gave a better dispersion than unmodified MWCNTs in the PLA matrix, and an even coating of PLA on the surface of c-MWCNTs was obtained, which increased the interfacial interaction. High insulation resistance analysis showed that the addition of c-MWCNTs increased the electric conductivity, and c-MWCNTs performed against the large dielectric coefficient and electrostatic state of PLA. These results demonstrated that c-MWCNTs modified PLA composites were beneficial for potential application in the development of heat-resisting and conductivity plastic engineering.

Electrical and mechanical properties of Cu-Cr-Zr alloy aged under imposed direct continuous current

The Cu-Cr-Zr alloys were aged at different temperatures for different time with different current densities. The results show that both the electrical conductivity and hardness are greatly improved after being aged with current at a proper temperature. The electrical conductivity increases approximately linearly with increasing current density while the hardness remains constant. The microstructure observation reveals that a much higher density of dislocations and nanosized Cr precipitates appear after the imposition of current, which contributes to the higher electrical conductivity and hardness. The mechanism is related with three factors： 1） Joule heating due to the current, 2） migration of mass electrons, 3） solute atoms, vacancies, and dislocations promoted by electron wind force.

SURFACE ELECTRICAL PROPERTIES AND STRUCTURE OF YTTRIA-PARTIALLY-STABILIZED ZIRCONIA IMPLANTED WITH ^(57) Fe IONS

Sintered plates of 5mol% yttria-partially-stabilized zirconia have been implanted at room temperature with 5 ×1015to 2 ×1017 Fe+ ions/cm2 at 140 KeV. Electrical measurement, Rutherford backscattering spec-troscopy(RBS), Raman spectroscopy and X-ray photoelec-tron spectroscopy(XPS) have been used to study the surface electrical properties and the structure of the implanted layer before and after thermal annealing treatment in N2.

Effect of Ba_(0.5)Bi_(0.5)Fe_(0.9)Sn_(0.1)O_3 addition on electrical properties of BaCo_(0.02)~ⅡCo_(0.04)~ⅢBi_(0.94)O_3 thick-film thermistors

Thick-film thermistor with negative temperature coefficient（NTC）, low room-temperature resistivity and modest thermistor constant was screen-printed on the alumina substrate by the combination of 30.94III0.04II0.02 B OBi Coa Co with Ba0.5Bi0.5Fe0.9Sn0.1O3. The electrical properties of the thick films were characterized by a digital multimeter, a Keithley 2400 and an impedance analyzer. The results show that with the Ba0.5Bi0.5Fe0.9Sn0.1O3 content increasing from 0.05 to 0.25, the values of room-temperature resistivity, thermistor constant and peak voltage of the thick films increases and are in the ranges of 1.47-26.5 ？·cm, 678-1345 K and 18.9-47.0 V, respectively. The corresponding current at the peak voltage of the thick films decreases and is in the range of 40-240 m A. The impedance spectroscopy measurement demonstrates that the as-prepared thick films show the abnormal electrical heterogeneous microstructure, consisting of high-resistive grains and less resistive grain boundary regions. It can be concluded that the addition of Ba0.5Bi0.5Fe0.9Sn0.1O3 into 30.94III0.04II0.02 Ba Co OBi Co improves the thermistor behavior and but also deteriorates the current characteristics.

Mechanical properties,electrical conductivity and microstructure of CuCrZr alloys treated with thermal stretch process

CuCrZr alloys were treated with the thermal stretch process at various temperatures from 100 to 300℃.The results reveal that the thermal stretch process is successfully developed to manufacture the precipitation hardening CuCrZr alloys with a good combination of microhardness and electrical conductivity.By increasing the tensile elongations at each temperature from 100 to 300℃,the microhardness increases whereas the electrical conductivity decreases slightly.Cr-containing precipitate phases with a Nishiyama-Wasserman orientation relationship to the copper matrix were observed by TEM.The achievement of high micro-hardness and acceptable electrical conductivity in the thermal stretch treated alloys is ascribed to the interactions of the heteroatom solution,dislocation increment,grain refinement and dispersive precipitation effect.

Effects of dwell time during sintering on electrical properties of 0.98(K_(0.5)Na_(0.5))NbO_3-0.02LaFeO_3 ceramics

The effects of dwell time on the phase structure, microstructure, and electrical properties were investigated for the 0.98（K0.sNa0.5）NbO3-0.02LaFeO3 ceramics （abbreviated as 0.98KNN-0.02LF）. All the ceramics sintered for different dwell time are of pure phase and the peak intensity of the 0.98KNN-0.02LF ceramics becomes stronger with a longer dwell time. Denser microstructures with larger grain size are developed for the sample with a longer dwell time. The maximum dielectric permittivity decreases with increasing the dwell time, and the deteriorative dielectric properties are due to the increasing grain size and the domain wall motion. Ferroelectric properties results indicate that 2Pr value slightly decreases with increasing the dwell time, while the 2Ec value increases. Consequently, the 0.98KNN-0.02LF ceramic sintered at 1150 ℃ for 2 h shows optimum dielectric properties （er=2253 and tan fi〈5%） and ferroelectric properties （2Pr=34.51 gC/cm2 and 2Ec=5.07 kV/mm）.

Self-assembled Carbon Nanotube/Silicone Composite Films and Their Electrical Properties for Electrical Device

Novel composites were synthesized using AEPTES （3-（2-aminoethylamino）propyltriethoxysilane）, which behaves as an excellent dispersant for MWCNTs （multiwall carbon nanotubes） in polymer film matrices. The thickness of the synthesized nanocomposite films ranged from 50 to 70 lam, having well-dispersed MWCNTs. Increasing the AEPTES concentration from 0.0196 to 0.0300 M, increased the amine content and the dispersion of MWCNTs. The film synthesized at 0.0300 M AETPES exhibited the greatest degree of dispersion among the three samples, which is consistent with a self-assembled silane group interacting with the MWCNT surface.

Structure, Electrical and Oxygen Transport Properties of Fe-Doped SrCoO3-δ Perovskites

The structure-property relationship of Fe-doped SrCoO3-δ was studied. With increase of Fe content in SrCol-xFexO3-δ from x=0 to x=0.2, the phase composition changed pro- gressively in the order of hexagonal→brownmillerite （main）＋hexagonal→cubic （main）＋ brownmillerite→single cubic phase. Transition between the hexagonal/brownmillerite phase and the cubic phase took place with variation of the operating conditions, and was associated with remarkable changes in the electrical conductivity and oxygen permeation flux.

Effects of carbonaceous conductive fillers on electrical and thermal properties of asphalt-matrix conductive composites

The relationship between thermal/electrical conductivity enhancement in asphalt-matrix mixtures and the properties of filling conductive particles is studied. The thermal properties with filling the carbon fiber, graphite conductive particles in asphalt-matrix mixtures are investigated. Based on the generalized effective medium theory （ EMT ）, the effective thermal and electrical conductivity of carbon fiber/asphalt and graphite/asphalt composites are theoretically elucidated. The theoretical results are found to be in reasonably well agreement with the experimental data. Moreover, the theoretical and experimental results show that the large-aspect-ratio shape of particles can help to achieve a large enhancement of effective conductivity, and the use of disk-like high conductivity particles can limit the additive contents for preserving the volumetric properties and mechanical properties of asphalt composites. The generalized effective medium theory model can be used for predicting the thermal and electrical properties of asphaltmatrix composites, which is still available for most of the thermal/electrical modifications in two-phase composites.

The effect of blending polypropylene on the electrical properties of polymeric insulation material Hifax

Extensive physical testing has suggested that polymeric material Hifax (Flexible Polypropylene)could be a promising candidate for the next generation of DC insulation. In the work presented in this paper,the DC conductivity and AC breakdown of this polymeric insulation material have been measured as a function of temperature. The results show that Hifax cable insulation has a higher AC breakdown strength than EPR and XLPE (crosslinked polyethylene), and the DC resistivity of Hifax is larger than that of XLPE and oil-impregnated paper insulations. The electrical stress coefficient of resistivity of Hifax wire insulation increases with temperature, which needs to be taken into account in calculating the electrical field distribution across DC cable insulation. It has been observed that there is an anomalous change in resistivity at high electrical field, suggesting charge trapping and detrapping processes are present in Hifax cable insulation. It is concluded that blending Hifax with 62% polypropylene decreases the breakdown strength significantly.

Effect of SiO_2 addition on the microstructure and electrical properties of ZnO-based varistors

The microstructure and electrical properties of ZnO-based varistors with the SiO2 content in the range of 0-1.00mol% were prepared by a solid reaction route. The varistors were characterized by scanning electron microscopy, X-ray diffraction, energy-dispersive X-ray spectrometry, inductively coupled plasma-atomic emission spectrometry, and X-ray photoelectron spectroscopy. The results indicate that the average grain size of ZnO decreases with the SiO2 content increasing. A new second phase （Zn2SiO4） and a glass phase （Bi2SiO5） are found. Element Si mainly exists in the grain boundary and plays an important role in controlling the Bi2O3 vaporization. The electric measurement shows that the incorporation of SiO2 can significantly improve the nonlinear properties of ZnO-based varistors, and the nonlinear coefficients of the varistors with SiO2 are in the range of 36.8-69.5. The varistor voltage reaches the maximum value of 463 V/mm and the leakage current reaches the minimum value of 0.11 μA at the SiO2 content of 0.75mol%.

Effect of annealing treatment on the structural, optical, and electrical properties of Al-doped ZnO thin films

Highly conductive and transparent Al-doped ZnO （AZO） thin films were prepared from a zinc target containing Al （1.5 wt.%） by direct current （DC） and radio frequency （RF） reactive magnetron sputtering. The structural, optical, and electrical properties of AZO films as-deposited and submitted to annealing treatment （at 300 and 400℃, respectively） were characterized using various techniques. The experimental results show that the properties of AZO thin films can be further improved by annealing treatment. The crystallinity of ZnO films improves after annealing treatment. The transmittances of the AZO thin films prepared by DC and RF reactive magnetron sputtering are up to 80% and 85% in the visible region, respectively. The electrical resistivity of AZO thin films prepared by DC reactive magnetron sputtering can be as low as 8.06 x 10-4 Ωcm after annealing treatment. It was also found that AZO thin films prepared by RF reactive magnetron sputtering have better structural and optical properties than that prepared by DC reactive magnetron sputtering.

Microstructure and electrical properties of Y_2O_3-doped ZnO-based varistor ceramics prepared by high-energy ball milling

Y2O3-doped ZnO-based varistor ceramics were prepared using high-energy ball milling （HEBM） and low-temperature sin- tering technique, with voltage-gradient of 1934-2197 V/mm, non-linear coefficients of 20.8-21.8, leakage currents of 0.59-1.04 μA, and densities of 5.46-5.57 g/cm3. With increasing Y2O3 content, the voltage-gradient increases because of the decrease of ZnO grain size; the non-linear coefficient and the leakage current improve but the density decreases because of more porosity; the donor con- centration and density of interface states decrease, whereas the barrier height and width increase because of the acceptor effect of Y2O3 in varistor ceramics.

Electrical properties of fly ash and its decarbonization by electrostatic separation

The basic principle of fly ash triboelectrification is analysed. The mineral electrical index and test method are introduced. The electric difference of different mineral composition of fly ash is discussed by analysis of chemical and mineral composition of fly ash in Xinwen power plant. The dielectric constant and charge-mass ratio of carbon and ash of fly ash are tested. Combined with the experimental study on rotary triboelectrostatic separation, the charged characteristic of fly ash particles with different size is gained. The results show that the dielectric constant of fly ash with different grain size decreased with the decrease of particle size, which lead to the poor electrical conductivity, Thus it can be seen that par- ticle size plays a leading role in conductivity, The charge of carbon and ash with each size increased with the decreased of particle size; and the charge-mass ratio between carbon and ash with the same size lar- ger with the decrease of size, which indicated that the finer particle size, the more favorable for triboelec- trification separation. In the same conditions, the best decarburization effect is realized when the particle size ranges from 0.038 to 0.074 ram, whose decarbonization rate and efficiency index reached 38.93% and 120.83% respectively.