Preparation of PrFe_(x)Co_(1-x)O_(3)/Mt catalyst and study on degradation of 2-hydroxybenzoic acid wastewater by catalytic wet peroxide oxidation

In this study,the perovskite nanocomposite PrFe_(x)Co_(1-x)O_(3)(Pr(S))was successfully synthesized by the sol-gel method;PrFe_(x)Co_(1-x)O_(3)/Al-pillared montmorillonite(Pr(S)/Mt)catalysts were prepared by impregnation(D)method and solid-melting(G)method,respectively,with Pr(S)as the active component and Al-pillared montmorillonite as the carrier.The catalysts were applied to treat the 2-hydroxybenzoic acid(2-HA)-simulated wastewater by catalytic wet peroxide oxidation(CWPO)technique,and the chemical oxygen demand(COD)removal rate and the 2-HA degradation rate were used as indicators to evaluate the catalytic performance.The results of the experiment indicated that the solid-melting method was more conducive to preparing the catalyst when the Co/Fe molar ratio of 7:3 and the optimal structural properties of the catalysts were achieved.The influence of operating parameters,including reaction temperature,catalyst dosage,H_(2)O_(2)dosage,pH,and initial 2-HA concentration,were optimized for the degradation of 2-HA by CWPO.The results showed that 97.64%of 2-HA degradation and 75.23%of COD removal rate were achieved under more suitable experimental conditions.In addition,after the catalyst was used five times,the degradation rate of 2-HA could still reach 76.93%,which implied the high stability and reusability of the catalyst.The high catalytic activity of the catalyst was due to the doping of Co into PrFeO_(3),which could promote the generation of HO·,and the high stability could be attributed to the loading of Pr(S)onto Al-Mt,which reduced the leaching of reactive metals.The study of reaction mechanism and kinetics showed that the whole degradation process conformed to the pseudo-firstorder kinetic equation,and the Langmuir-Hinshelwood method was applied to demonstrate that catalysis was dominant in the degradation process.

Four-channel catalytic micro-reactor based on alumina hollow fiber membrane for efficient catalytic oxidation of CO

The traditional automotive catalytic converter using commercial ceramic honeycomb carriers has many problems such as high back pressure,low engine efficiency,and high usage of precious metals.This study proposes a four-channel catalytic micro-reactor based on alumina hollow fiber membrane,which uses phase inversion method for structural molding and regulation.Due to the advantages of its carrier,it can achieve lower ignition temperature under low noble metal loading.With Pd/CeO_(2) at a loading rate of 2.3%(mass),the result showed that the reaction ignition temperature is even less than 160℃,which is more than 90℃ lower than the data of commercial ceramic substrates under similar catalyst loading and airspeed conditions.The technology in turn significantly reduces the energy consumption of the reaction.And stability tests were conducted under constant conditions for 1000 h,which proved that this catalytic converter has high catalytic efficiency and stability,providing prospects for the design of innovative catalytic converters in the future.

A highly hydrothermal stable copper-based catalyst for catalytic wet air oxidation of m-cresol in coal chemical wastewater

Catalytic wet air oxidation(CWAO) can degrade some refractory pollutants at a low cost to improve the biodegradability of wastewater. However, in the presence of high temperature and high pressure and strong oxidizing free radicals, the stability of catalysts is often insufficient, which has become a bottleneck in the application of CWAO. In this paper, a copper-based catalyst with excellent hydrothermal stability was designed and prepared. TiO_(2) with excellent stability was used as the carrier to ensure the longterm anchoring of copper and reduce the leaching of the catalyst. The one pot sol–gel method was used to ensure the super dispersion and uniform distribution of copper nanoparticles on the carrier, so as to ensure that more active centers could be retained in a longer period. Experiments show that the catalyst prepared by this method has good stability and catalytic activity, and the catalytic effect is not significantly reduced after 10 cycles of use. The oxidation degradation experiment of m-cresol with the strongest biological toxicity and the most difficult to degrade in coal chemical wastewater was carried out with this catalyst. The results showed that under the conditions of 140℃, 2 MPa and 2 h, m-cresol with a concentration of up to 1000 mg·L^(-1) could be completely degraded, and the COD removal rate could reach 79.15%. The biological toxicity of wastewater was significantly reduced. The development of the catalyst system has greatly improved the feasibility of CWAO in the treatment of refractory wastewater such as coal chemical wastewater.

Life cycle assessment of high concentration organic wastewater treatment by catalytic wet air oxidation

There have been many studies on life cycle assessment in sewage treatment,but there are scarce few studies on the treatment of industrial wastewater in combination with advanced oxidation technology,especially in catalytic wet air oxidation(CWAO).There are no cases of using actual industrialized data onto life cycle assessment.This paper uses Simapro 9.0 software to establish a life cycle assessment model for the treatment of high-concentration organic wastewater by CWAO,and comprehensively explains the impact on the environment from three aspects:the construction phase,the operation phase and the demolition phase.In addition,sensitivity analysis and uncertainty analysis were performed.The results showed that the key factors affecting the environment were marine ecotoxicity,mineral resource consumption and global warming,the operation stage had the greatest impact on the environment,which was related to high power consumption during operation and emissions from the treatment process.Sensitivity analysis showed that electricity consumption has the greatest impact on abiotic depletion and freshwater aquatic ecotoxicity,and it also proved that global warming is mainly caused by pollutant emissions during operation phase.Monte Carlo simulations found slightly higher uncertainty for abiotic depletion and toxicity-related impact categories.

Fabrication of highly dispersed carbon doped Cu-based oxides as superior selective catalytic oxidation of ammonia catalysts via employing citric acid-modified carbon nanotubes doping CuAl-LDHs

In this work,the CuAl-LDO/c-CNTs catalyst was fabricated via in situ oriented assembly of layered-double hydroxides(LDHs)and citric acid-modified carbon nanotubes(c-CNTs)followed by annealing treatment,and evaluated in the selective catalytic oxidation(SCO)of NH_(3)to N_(2).The CuAl-LDO/c-CNTs catalyst presented better catalytic performance(98%NH_(3)conversion with nearly 90%N_(2)selectivity at 513 K)than other catalysts,such as CuAlO_(x)/CNTs,CuAlO_(x)/c-CNTs and CuAl-LDO/CNTs.Multiple characterizations were utilized to analyze the difference of physicochemical properties among four catalysts.XRD,TEM and XPS analyses manifested that CuO and Cu_(2)O nanoparticles dispersed well on the surface of the Cu Al-LDO/c-CNTs catalyst.Compared with other catalysts,larger specific surface area and better dispersion of CuAl-LDO/c-CNTs catalyst were conducive to the exposure of more active sites,thus improving the redox capacity of the active site and NH_(3)adsorption capacity.In-situ DRIFTS results revealed that the internal selective catalytic reduction(iSCR)mechanism was found over CuAl-LDO/c-CNTs catalyst.

A comparison between high temperature catalytic and persulfate oxidation for the determination of total dissolved nitrogen in natural waters

Total dissolved nitrogen(TDN) is an important parameter for assessing the nutrient cycling and status of natural waters.The accurate determination of TDN in natural waters is essential for assessing its contents and distinguishing different forms of nitrogen in the water.The TDN in various systems has been largely documented,and the concentrations of TDN are usually obtained using high-temperature catalytic(HTC) or persulfate oxidation(PO).However,the accuracy of these methods and their suitability for all types of natural waters are still unclear.To explore both methods in-depth,assorted samples were tested,including eight solutions composed of nitrogen-containing compounds(3 dissolved inorganic nitrogen fractions:NO_(3)^(-),NO_(2)^(-)and NH_(4)^(+);5 organic compounds:EDTA-2Na,vitamin B1,vitamin B12,amino acids,and urea) and 105 natural waters which were collected from an open ocean(Northwest Pacific Ocean,28),a marginal sea(Yellow Sea,34),an estuary(Huanghe River mouth,31),rivers(Huanghe River,4;Licun River,4),and precipitations(4 samples).The results showed that heterocycles and molecular dimensions had certain effects on the oxidation efficiency of the PO method but had little effect on HTC.There was no significant difference between the two methods for natural waters,but HTC was more suitable for deep-sea samples with low TDN concentrations(less than 10 μmol/L) and low organic activity.Overall,HTC has a relatively simple measurement process,a high degree of automation,and low error.Therefore,HTC can be recommended to determine the TDN of samples in freshwater and seawater.

Progress in research on catalysts for catalytic oxidation of formaldehyde

Formaldehyde（HCHO）is carcinogenic and teratogenic,and is therefore a serious danger to human health.It also adversely affects air quality.Catalytic oxidation is an efficient technique for removing HCHO.The development of highly efficient and stable catalysts that can completely convert HCHO at low temperatures,even room temperature,is important.Supported Pt and Pd catalysts can completely convert HCHO at room temperature,but their industrial applications are limited because they are expensive.The catalytic activities in HCHO oxidation of transition-metal oxide catalysts such as manganese and cobalt oxides with unusual morphologies are better than those of traditional MnO2,Co3O4,or other metal oxides.This is attributed to their specific structures,high specific surface areas,and other factors such as active phase,reducibility,and amount of surface active oxygens.Such catalysts with various morphologies have great potential and can also be used as catalyst supports.The loading of relatively cheap Ag or Au on transition-metal oxides with special morphologies potentially improves the catalytic activity in HCHO removal at room temperature.The preparation and development of new nanocatalysts with various morphologies and structures is important for HCHO removal.In this paper,research progress on precious-metal and transition-metal oxide catalyst systems for HCHO oxidation is reviewed; topics such as oxidation properties,structure–activity relationships,and factors influencing the catalytic activity and reaction mechanism are discussed.Future prospects and directions for the development of such catalysts are also covered.

Synthesis of three-dimensional ordered mesoporous MnO_2 and its catalytic performance in formaldehyde oxidation

Three-dimensional（3D）ordered mesoporous MnO2 was prepared using KIT-6 mesoporous molecular sieves as a hard template.The material was used for catalytic oxidation of HCHO.The material has high surface areas and the mesoporous characteristics of the template,with cubic symmetry（ia3d）.It consists of a β-MnO2 crystalline phase corresponding to pyrolusite,with a rutile structure.Transmission electron microscopy and X-ray photoelectron spectroscopy showed that the 3D-MnO2 catalyst has a large number of exposed Mn4＋ ions on the（110）crystal plane surfaces,with a lattice spacing of 0.311 nm; this enhances oxidation of HCHO.Complete conversion of HCHO to CO2 and H2O was achieved at 130 °C on 3D-MnO2; the same conversions on α-MnO2 and β-MnO2 nanorods were obtained at 140 and 180 °C,respectively,under the same conditions.The specific mesoporous structure,high specific surface area,and large number of surface Mn4＋ ions are responsible for the catalytic activity of 3D-MnO2 in HCHO oxidation.

Effect of pore size in mesoporous MnO_2 prepared by KIT-6 aged at different temperatures on ethanol catalytic oxidation

KIT‐6 mesoporous silica aged at 40,100,and 150°C were used as hard templates to prepare different mesoporous MnO2 catalysts,marked as Mn‐40,Mn‐100,and Mn‐150,respectively.The catalytic activities of these catalysts and the effect of pore sizes on ethanol catalytic oxidation were investigated.Mn‐40,Mn‐100,and Mn‐150 have triple,double,and single pore systems,respectively.On decreasing the aging temperature of KIT‐6,the pore sizes of KIT‐6 decrease and that of mesoporous MnO2 catalysts increase.The pore sizes and catalytic activities increase in the order:Mn‐40>Mn‐100>Mn‐150.Mn‐40 catalyst has a higher TOF(0.11 s–1 at 120°C)and the best catalytic activity for ethanol oxidation because of a bigger pore size with three pore systems with maximum distribution at 1.9,3.4,and 6.6 nm,decrease in symmetry and degree of order,more surface lattice oxygen species,oxygen vacancies resulting from more Mn3+ions,and better low‐temperature reducibility.

Electrocatalytic Oxidation of Saccharides at MoOx/AuNPs Modified Electrode Towards Analytical Application

The MoOx/AuNPs composite film modified glassy carbon electrode was fabricated by electro-depositing simultaneously gold nanoparticles and molybdenum oxides using cyclic voltammetry. The morphology and topography of the MoOx/AuNPs composite were char-acterized by scan electron microscopy and X-ray photoelectron spectroscopy respectively, and the electrocatalytic oxidation of glucose at the MoOx/AuNPs composite film was inves-tigated and analyzed in detail. It was shown that the MoOx/AuNPs composite was of strong electrocatalytic activity towards oxidation of glucose as well as other saccharides, so that an attempt was made for direct voltammetric determination of glucose. Then the positive scan polarization reverse catalytic voltammetry was proposed for the first time. Based on this method, the pure oxidation current was extracted by subtraction of the blank current in the reverse scan. The current sensitivity was enhanced tremendously and the signal to noise ra-tio was improved adequately. The electrocatalytic oxidation of glucose at the MoOx/AuNPs modified electrode was performed in alkaline medium, a wide linear range from 0.01 mmol/L to 4.0 mmol/L of glucose, a higher current sensitivity of 2.35 mA/（mmol/L·cm2）, and a lower limit of detection of 9.01 μmol/L （at signal/noise=3） were achieved. In addition, the electrocatalytic oxidation of other saccharides such as lactose, fructose and sucrose was also evaluated.

Few-layered hexagonal boron nitride nanosheets stabilized Pt NPs for oxidation promoted adsorptive desulfurization of fuel oil

A few-layered hexagonal boron nitride nanosheets stabilized platinum nanoparticles(Pt/h-BNNS)is engineered for oxidation-promoted adsorptive desulfurization(OPADS)of fuel oil.It was found that the few-layered structure and the defective sites of h-BNNS not only are beneficial to the stabilization of Pt NPs but also favor the adsorption of aromatic sulfides.By employing Pt/h-BNNS with a Pt loading amount of 1.19 wt%as the active adsorbent and air as an oxidant,a 98.0%sulfur removal over dibenzothiophene(DBT)is achieved along with a total conversion of the DBT to the corresponding sulfones(DBTO_(2)).Detailed experiments show that the excellent desulfurization activity originates from the few-layered structure of h-BNNS and the high catalytic activity of Pt NPs.In addition,the OPADS system with Pt/h-BNNS as the active adsorbent shows remarkable stability in desulfurization performance with the existence of different interferents such as olefin,and aromatic hydrocarbons.Besides,the Pt/h-BNNS can be recycled 12 times without a significant decrease in desulfurization performance.Also,a process flow diagram is proposed for deep desulfurization of fuel oil and recovery of high value-added products,which would promote the industrial application of such OPADS strategy.

Effects of Co_3O_4 nanocatalyst morphology on CO oxidation:Synthesis process map and catalytic activity

This study focuses on drawing a hydrothermal synthesis process map for Co3O4 nanoparticles with various morphologies and investigating the effects of Co3O4 nanocatalyst morphology on CO oxidation.A series of cobalt-hydroxide-carbonate nanoparticles with various morphologies（i.e.,nanorods,nanosheets,and nanocubes） were successfully synthesized,and Co3O4 nanoparticles were obtained by thermal decomposition of the cobalt-hydroxide-carbonate precursors.The results suggest that the cobalt source is a key factor for controlling the morphology of cobalt-hydroxide-carbonate at relatively low hydrothermal temperatures（≤ 140℃）.Nanorods can be synthesized in CoCl2 solution,while Co（NO3）2 solution promotes the formation of nanosheets.Further increasing the synthesis temperature（higher than 140 ℃） results in the formation of nanocubes in either Co（NO3）2 or CoCl2 solution.The reaction time only affects the size of the obtained nanoparticles.The presence of CTAB could improve the uniformity and dispersion of particles.Co3O4 nanosheets showed much higher catalytic activity for CO oxidation than nanorods and nanocubes because it has more abundant Co^（3＋） on the surface,much higher reducibility,and better oxygen desorption capacity.

Effect of Precipitation Method and Ce Doping on the Catalytic Activity of Copper Manganese Oxide Catalysts for CO Oxidation

The influence of Ce doping and the precipitation method on structural properties and the catalytic activity of copper manganese oxides for CO oxidation at ambient temperature have been investigated. The catalysts were characterized by means of the powder X-ray diffraction and N2 adsorption-desorption, the inductively coupled plasma atomic emission spectrometry, the temperature programmed reduction, diffuse reflectance UV-Vis spectra, and the X-ray photoelectron spectroscopy. It was found that after doping little amount of Ce in copper manganese oxide, CeO2 phase was highly dispersed and could prevent sintering and aggregating of the catalyst, the size of the catalytic material was decreased, the reducibility was enhanced, the specific surface area was increased and the formation of the active sites for the oxidation of CO was improved significantly. Therefore, the activity of the rare earth promoted catalyst was enhanced remarkably.

Pd micro-nanoparticles electrodeposited on graphene/polyimide membrane for electrocatalytic oxidation of formic acid

A novel Pd electrocatalyst with flowerlike micro-nanostructures was synthesized by electrochemical deposition on a flexible graphene/polyimide（Gr/PI） composite membrane and characterized by scanning electron microscopy（SEM）,X-ray diffraction（XRD）.The Pd micro-nanoparticles were prepared on a COOH-CNTs/PI membrane as a comparative sample.The XRD and SEM investigations for Pd electrodeposition demonstrate that the particle size of Gr/PI composite membrane is smaller than that of COOH-CNTs/PI membrane,while the uniform and dense distribution of Pd micro-nanoparticles on the Gr/PI composite membrane is greater than that on the COOH-CNTs/PI membrane.The electrocatalytic properties of Pd/Gr/PI and Pd/COOH-CNTs/PI catalysts for the oxidation of formic acid were investigated by cyclic voltammetry（CV） and chronoamperometry（CA）.It is found that the electrocatalytic activity and stability of Pd/Gr/PI are superior to those of Pd/COOH-CNTs/PI catalyst.This is because smaller metal particles and higher dense distribution desirably provide abundant catalytic sites and mean higher catalytic activity.Therefore,the Pd/Gr/PI catalyst has better catalytic performance for formic acid oxidation than the Pd/COOH-CNTs/PI catalyst.

Low-temperature catalytic oxidation of NO over Mn-Ce-O_x catalyst

A series of manganese-cerium oxide catalysts were prepared by different methods and used for low-temperature catalytic oxidation of NO in the presence of excess O2.Their surface properties were evaluated by means of BET and were characterized by using scanning electron microscopy(SEM) and X-ray diffractometer(XRD).The activity test of Mn-Ce-Ox catalysts showed that addition of Ce enhanced the activities of NO oxidation.The most active catalysts with a molar Ce/(Mn+Ce) ratio of 0.3 were prepared by co-precip...

Selective catalytic oxidation of NO over iron and manganese oxides supported on mesoporous silica

The selective catalytic oxidation （SCO） of NO was studied on a catalyst consisting of iron-manganese oxide supported on mesoporous silica （MPS） with different Mn/Fe ratios. Effects of the amount of manganese and iron, oxygen, and calcination temperature on NO conversion were also investigated. It was found that the Mn-Fe/MPS catalyst with a Mn/Fe molar ratio of 1 showed the highest activity at the calcination temperature of 400 °C. The results showed that over this catalyst, NO conversion reached 70% under the condition of 280 °C and a space velocity of 5000 h-1. SO2 and H2O had no adverse impact on the reaction activity when the SCO reaction temperature was above 240 °C. In addition, the SCO activity was suppressed gradually in the presence of SO2 and H2O below 240 °C, and such an effect was reversible after heating treatment.

Influence of the structure of TiO_2 , CeO_2 , and CeO_2-TiO_2 supports on the activity of Ru catalysts in the catalytic wet air oxidation of acetic acid

Ru catalysts, supported on TiO 2 , CeO 2 , and CeO 2 -TiO 2 , were prepared by the impregnation method. The effect of the structure of the supports on the activity of Ru catalysts was investigated in the catalytic wet air oxidation （CWAO） of acetic acid under 230℃ and 5 MPa in a batch reactor. Physical properties including the surface area, crystalline phase, and surface components of the Ru catalysts were characterized by N 2 adsorption, X-ray powder diffraction （XRD）, and X-ray photoelectron spectroscopy （XPS）. The CeO 2 -based Ru catalysts had good activity, and the prepared RuO 2 /CeO 2 catalyst showed markedly higher activity than the RuO 2 /CeO 2 -TiO 2 catalyst. The surface structure, the high amount of chemisorbed oxygen on the catalyst surface, and the suitable pH pzc value of the supports played an important role in the activity of the Ru catalysts in CWAO of acetic acid.

Study on Catalytic Wet Oxidation of H_2S into Sulfur on Fe/Cu Catalyst

A wet catalytic oxidation at room temperature was investigated with solution containing ferric, ferrous and cupric ions for H2S removal. The experiments were carried out in a two step process, and the results obtained show that the removal efficiency of H2S can always reach 100% in a 300 mm scrubbing column with four sieve plates, and the regeneration of ferric ions in 200 mm bubble column can match the consumed ferric species in absorption. Removal of H2S, production of elemental sulfur and regeneration of ferric, cupric ions can all be accomplished at the same time. No raw material is consumed except O2 in flue gas or air, the process has no secondary pollution and no problem of catalyst degradation and congestion.

Synthesis of cerium-doped MCM-48 molecular sieves and its catalytic performance for selective oxidation of cyclohexane

Cerium-doped MCM-48 molecular sieves were synthesized hydrothermally and characterized by X-ray diffraction, nitrogen adsorption, transmission electron microscope, FT-IR spectroscopy, UV-visible spectroscopy, and Raman spectroscopy. The results showed that all the samples held the structure of MCM-48, and Ce could enter the framework of MCM-48. However, when Ce/Si molar ratio in the sampies was high （0.04 or 0.059）, there were CeO2 crystallites as secondary phase in the extraframework of MCM-48. Ce-doped MCM-48 was a very efficient catalyst for the oxidation of cyclohexane in a solvent-free system with oxygen as an oxidant. In the conditions of 0.5 MPa 02 and 413 K for 5 h, the conversion of cyclohexane was 8.1% over Ce-MCM-48-0.02, the total selectivity of cyclohexanol and cyclohaxnone was 98.7%. With an increase of Ce content, the conversion of cyclohexane and the selectivity to cyclohexanol decreased somewhat, but the selectivity to cyclohexanone increased.

Selective catalytic oxidation of NO with O_2 over Ce-doped MnO_x/TiO_2 catalysts

A series of Ce-doped MnOx/TiO2 catalysts were prepared by impregnation method and used for catalytic oxidation of NO in the presence of excess O2. The sample with the Ce doping concentration of Ce/Mn=l/3 and calcined at 300 ℃ shows a superior activity for NO oxidation to NO2. On Ce（1）Mn（3）Ti catalyst, 58% NO conversion was obtained at 200 ℃ and 85% NO conversion at 250 ℃ with a GHSV of 41000 h-1, which was much higher than that over MnOx/TiO2 catalyst （48% at 250 ℃）. Characterization results implied that the higher activity of Ce（1）Mn（3）Ti could be attributed to the enrichment of well-dispersed MnO2 on the surface and the abundance of Mn3＋ and Zi3＋ species. The addition of Ce into MnO2/TiO2 could improve oxygen storage capacity and facilitate oxygen mobility of the catalyst as shown by PL and ESR, so that its activity for NO oxidation could be enhanced. The effect of H2O and SO2 on the catalyst activity was also investigated.