Co-Production of High-Grade Dissolving Pulp,Furfural,and Lignin from Eucalyptus via Extremely Low Acid Pretreatment and Pulping Technologies and Catalysis

Hemicellulose and lignin are not reasonably utilized during the dissolved pulp preparation process.This work aimed to propose a process for the co-production of dissolving pulp,furfural,and lignin from eucalyptus.High-grade dissolving pulp was prepared from eucalyptus using a combination of extremely low acid(ELA)pretreatment,Kraft cooking,and elementary chlorine-free(ECF)bleaching.The obtained pre-hydrolysate was catalytic conversion into furfural in a biphasic system,and lignin during Kraft cooking and ECF was recovered.The process condition was discussed as well as the mass flow direction.The results showed that ELA pretreatment could effectively remove 80.1%hemicellulose.Compared with traditional hydrothermal pretreatment,the ELA pretreatment significantly increased the xylose yield from 5.05 to 14.18 g/L at 170℃ for 2 h,which had practical significance for furfural production.The 82.7%furfural yield and 82.9%furfural selectivity were obtained from xylose-rich pre-hydrolysate using NaCl as a phase modifier in a biphasic system with 4-methyl-2-pentanone(MIBK)as an organic phase by ion exchange resin catalysts at 190℃ for 2 h.Subsequently,the pretreated eucalyptus was subjected to Kraft cooking,and the optimal alkali amount was 14%.Then,the Kraft pulp was bleached using the O-D1-EP-D_(2) sequence,and dissolving pulp was obtained with an ISO brightness of 86.0%,viscosity of 463 mL/g,andα-cellulose content of 95.4%.The Kraft lignin which has a potential application was investigated by 2D-HSQC NMR and 31P NMR.The results showed that the S/G ratio of Kraft lignin was 1.93,and the content of phenolic hydroxyl groups was 2.53 mmol/g.Moreover,based on the above proposed process,30.5 g dissolving pulp,5.5 g furfural,and 21.2 g lignin per 100 g eucalyptus chips(oven dry)were produced.This research will provide new catalysis and pulping technical routes for dissolving pulp,furfural,and Kraft lignin products,which are in great demand in the chemical industry.

Development, Application and Prospect of Dissolving Microneedles

In recent years, as a new transdermal drug delivery method, microneedle transdermal drug delivery technology accelerates the absorption of drugs through micron pores, which has been widely used in the field of medicine and cosmetics. Dissolving microneedles have the characteristics of good biocompatibility and fast dissolution speed, which attract more and more researchers’ attention and research. In this paper, the concept, properties and preparation methods of dissolving microneedles as well as the research status of dissolving microneedles in the field of medicine and cosmetics in recent years were summarized and prospected, so as to enable researchers to have a clearer and comprehensive understanding of dissolving microneedles and prospect the application and development prospects of dissolving microneedles in the industry.

Recent progress on nanomaterial-based electrochemical dissolved oxygen sensors

Dissolved oxygen(DO)usually refers to the amount of oxygen dissolved in water.In the environment,medicine,and fermentation industries,the DO level needs to be accurate and capable of online monitoring to guide the precise control of water quality,clinical treatment,and microbial metabolism.Compared with other analytical methods,the electrochemical strategy is superior in its fast response,low cost,high sensitivity,and portable device.However,an electrochemical DO sensor faces a trade-off between sensitivity and long-term stability,which strongly limits its practical applications.To solve this problem,various advanced nanomaterials have been proposed to promote detection performance owing to their excellent electrocatalysis,conductivity,and chemical stability.Therefore,in this review,we focus on the recent progress of advanced nanomaterial-based electrochemical DO sensors.Through the comparison of the working principles on the main analysis techniques toward DO,the advantages of the electrochemical method are discussed.Emphasis is placed on recently developed nanomaterials that exhibit special characteristics,including nanostructures and preparation routes,to benefit DO determination.Specifically,we also introduce some interesting research on the configuration design of the electrode and device,which is rarely introduced.Then,the different requirements of the electrochemical DO sensors in different application fields are included to provide brief guidance on the selection of appropriate nanomaterials.Finally,the main challenges are evaluated to propose future development prospects and detection strategies for nanomaterial-based electrochemical sensors.

Dissolvable temporary barrier:a novel paradigm for flexible hydrogel patterning in organ-on-a-chip models

A combination of hydrogels and microfluidics allows the construction of biomimetic three-dimensional(3D)tissue models in vitro,which are also known as organ-on-a-chipmodels.The hydrogel patterningwith awell-controlled spatial distribution is typically achieved by embedding sophisticated microstructures to act as a boundary.However,these physical barriers inevitably expose cells/tissues to a less physiologically relevant microenvironment than in vivo conditions.Herein,we present a novel dissolvable temporary barrier(DTB)strategy that allows robust and flexible hydrogel patterning with great freedom of design and desirable flow stimuli for cellular hydrogels.The key aspect of this approach is the patterning of a water-soluble rigid barrier as a guiding path for the hydrogel using stencil printing technology,followed by a barrier-free medium perfusion after the dissolution of the DTB.Single and multiple tissue compartments with different geometries can be established using either straight or curved DTB structures.The effectiveness of this strategy is further validated by generating a 3D vascular network through vasculogenesis and angiogenesis using a vascularized microtumor model.As a new proof-of-concept in vasculature-on-a-chip,DTB enables seamless contact between the hydrogel and the culture medium in closed microdevices,which is an improved protocol for the fabrication ofmultiorgan chips.Therefore,we expect it to serve as a promising paradigm for organ-on-a-chip devices for the development of tumor vascularization and drug evaluation in the future preclinical studies.

A review of physicochemical properties of dissolved organic carbon and its impact over mountain glaciers

Investigating the characteristics and transformation of water-soluble carbonaceous matter in the cryosphere regions is important for understanding biogeochemical process in the earth system.Water-soluble carbonaceous matter is a heterogeneous mixture of organic compounds that is soluble in aquatic environments.Despite its importance,we still lack systematic understanding for dissolved organic carbon(DOC)in several aspects including exact chemical composition and physical interactions with microorganisms,glacier meltwater.This review presents the chemical composition and physical properties of glacier DOC deposited through anthropogenic emission,terrestrial,and biogenic sources.We present the molecular composition of DOC and its effect over snow albedo and associated radiative forcings.Results indicate that DOC in snow/ice is made up of aromatic protein-like species,fulvic acid-like materials,and humic acid-like materials.Light-absorbing impurities in surface snow and glacier ice cause considerable albedo reduction and the associated radiative forcing is definitely positive.Water-soluble carbonaceous matter dominated the carbon transport in the high-altitude glacial area.Owing to prevailing global warming and projected increase in carbon emission,the glacial DOC is expected to release,which will have strong underlying impacts on cryosphere ecosystem.The results of this work have profound implications for better understanding the carbon cycle in high altitude cryosphere regions.A new compilation of globally distributed work is required,including large-scale measurements of glacial DOC over high-altitude cryosphere regions,to overcome and address the scientific challenges to constrain climate impacts of light-absorbing impurities related processes in Earth system and climate models.

Straw mulching alters the composition and loss of dissolved organic matter in farmland surface runoff by inhibiting the fragmentation of soil small macroaggregates

Straw mulching is a widespread practice for reducing the soil carbon loss caused by erosion.However,the effects of straw mulching on dissolved organic matter(DOM)runoff loss from black soil are not well studied.How straw mulching affects the composition and loss of runoff DOM by changing soil aggregates remains largely unclear.Here,a straw mulching treatment was compared to a no mulching treatment(as a control)on sloping farmland with black soil erosion in Northeast China.We divided the soil into large macroaggregates(>2 mm),small macroaggregates(0.25-2 mm),and microaggregates(<0.25 mm).After five rain events,the effects of straw mulching on the concentration(characterized by dissolved organic carbon(DoC)and composition(analyzed by fluorescence spectroscopy)of runoff and soil aggregate DOM were studied.The results showed that straw mulching reduced the runoff amount by 54.7%.Therefore,although straw mulching increased the average DOc concentration in runoff,it reduced the total runoff DOM loss by 48.3%.The composition of runoff DOM is similar to that of soil,as both contain humic-like acid and protein-like components.With straw mulching treatment,the protein-like components in small macroaggregates accumulated and the protein-like components in runoff declined with rain events.Fluorescence spectroscopy technology may help in understanding the hydrological paths of rain events by capturing the dynamic changes of runoff and soil DOM characteristics.A variation partitioning analysis(VPA)indicated that the DOM concentration and composition of microaggregates explained 68.2%of the change in runoff DOM from no mulching plots,while the change in runoff DOM from straw mulching plots was dominated by small macroaggregates at a rate of 55.1%.Taken together,our results demonstrated that straw mulching reduces the fragmentation of small macroaggregates and the loss of microaggregates,thus effecting DOM compositions in soil and reducing the DOM loss in runoff.These results provide a theoretical basis for reducing carbon loss in sloping farmland.

Impact of transparent exopolymer particles on the dynamics of dissolved organic carbon in the Amundsen Sea,Antarctica

The Southern Ocean is an important carbon sink pool and plays a critical role in the global carbon cycling.The Amundsen Sea was reported to be highly productive in inshore area in the Southern Ocean.In order to investigate the influence of transparent exopolymer particles(TEP)on the behavior of dissolved organic carbon(DOC)in this region,a comprehensive study was conducted,encompassing both open water areas and highly productive polynyas.It was found that microbial heterotrophic metabolism is the primary process responsible for the production of humic-like fluorescent components in the open ocean.The relationship between apparent oxygen utilization and the two humic-like components can be accurately described by a power-law function,with a conversion rate consistent with that observed globally.The presence of TEP was found to have little impact on this process.Additionally,the study revealed the accumulation of DOC at the sea surface in the Amundsen Sea Polynya,suggesting that TEP may play a critical role in this phenomenon.These findings contribute to a deeper understanding of the dynamics and surface accumulation of DOC in the Amundsen Sea Polynya,and provide valuable insights into the carbon cycle in this region.

Impacts of Water-Sediment Regulation Scheme on Chromophoric Dissolved Organic Matter in the Lower Yellow River

As a river with more than 3000 reservoirs in its watershed,the Yellow River has been affected by dams not only on the sediment load,but also on the water quality.Water-sediment regulation scheme(WSRS),which has been carried out annually in the Yellow River since 2002,is a typical human activity affecting river water quality.Chromophoric dissolved organic matter(CDOM)in river is susceptible to changes in ecological and environmental conditions as well as human activities.Here,we report variations in dissolved organic carbon concentrations,compositions and sources of CDOM in time series samples in the lower Yellow River during WSRS.In addition,a parallel factor fluorescence analysis(PARAFAC)method is applied to identify different fluorescent components in water samples during WRSR,showing four major components including tryptophan-like component(C1),microbial humic-like component(C2),terrestrial humic-like component(C3)and tyrosine-like component(C4).In general,C1 increased after water regulation,while C2 and C3 increased after sediment regulation,indicating that the water and sediment released by the dam have different effects on CDOM compositions.Under the impacts of the dam,source of CDOM in the lower Yellow River is mainly autochthonous related to microbial activities,and is regulated by the terrestrial input during WSRS period.Sediment resuspension inhibits microbial activities and reduces the production of autochthonous CDOM.Overall,human activities especially WSRS,as exemplified here,significantly alter the quality and quantity of CDOM in the lower Yellow River,affecting CDOM dynamics and biogeochemical processes in the estuarine environment.

Dissolved Organic Matter Features of Three Adjacent Eastern Mediterranean Urbanized Watersheds

Landscape urbanization broadly affects ecosystems in coastal watersheds, but, until now, the influence of nonpoint source urban inputs on dissolved organic matter (DOM) amount, composition, and source is poorly understood. To understand how DOM composition varied with urbanization, fluorescence excitation-emission matrices (EEMs) were determined for urban and non-urban waters from upstream to downstream sites along three adjacent coastal watersheds that flow into the Mediterranean Sea. Two humic DOM fluorescent components (humic-like and fulvic-like peaks) and two proteinic components (tyrosine-like and tryptophane-like peaks) were identified by EEM fluorescence. The results indicated that urbanization had an important influence on DOM concentration and composition, with urban waters having a high degree of DOM variation due to different land uses surrounding each body of water. Urban waters show a higher DOM fluorescence index (FI), the highest fluorescence intensity of protein-like manifested also by BIX values, and a lower value of the humification index (HIX) than non-urban waters which were dominated by allochthonous inputs. In addition, the EEM was compared in dry and wet season where higher DOM amounts and FI appeared in summer due to autochthonous production coming from algae growth compared to allochthonous input from rainfall dominated in wet season. The concentration of DOC increased from upstream to downstream for the three rivers, especially Beirut River. The increase in DOC values was observed in both dry and wet seasons by 39 and 19 times respectively compared to upstream (0.93 - 0.91 mgC/L).

Study of Total Dissolved Solids (TDS) Concentrations Factor of SWCC Al-Khobar Plant Seawater Intakes

This study presents a significant contribution to the field of water quality assessment and sustainable water management practices. By evaluating the levels of total dissolved solids (TDS) in seawater intakes within Al-Khobar desalination production system, the study addresses a crucial aspect of water treatment and environmental impact assessment. The findings provide valuable insights into the variations and trends of TDS levels across different phases of the system, highlighting the importance of monitoring and management strategies. The study provided both gravimetric total dissolved solids (TDS) and electrical conductivity (EC) measurements to analyze TDS calculation factor and evaluate measurement accuracy. Results revealed significant variations in TDS levels across the sampling locations, with phase-2 exhibiting higher levels and greater fluctuations. Phase-3 displayed similar trends but with lower TDS levels, while phase-4 showed slightly different behavior with higher average TDS levels. EC measurements demonstrated a strong correlation with TDS, providing a reliable estimation. However, additional methods such as gravimetric analysis should be employed to confirm TDS measurements. The findings contribute to understanding water quality in the Al-Khobar desalination system, aiding in monitoring, management, and decision-making processes for water treatment and environmental impact assessment. The study enhances the credibility of water quality assessments and supports sustainable water management practices.

Impacts of Climate Change on Seawater Temperature and Total Dissolved Solids: Challenges and Sustainable Solutions for Reverse Osmosis Desalination in the Arabian Gulf Region

This article examines the influence of seawater temperature and total dissolved solids (TDS) on reverse osmosis (RO) desalination in the Arabian Gulf region, with a focus on the impact of climate change. The study highlights the changes in seawater temperature and TDS levels over the years and discusses their effects on the efficiency and productivity of RO desalination plants. It emphasizes the importance of monitoring TDS levels and controlling seawater temperature to optimize water production. The article also suggests various solutions, including intensive pre-treatment, development of high-performance membranes, exploration of alternative water sources, and regulation of discharges into the Gulf, to ensure sustainable water supply in the face of rising TDS levels and seawater temperature. Further research and comprehensive monitoring are recommended to understand the implications of these findings and develop effective strategies for the management of marine resources in the Arabian Gulf.

STUDY ON THE MECHANISM OF NYLON 6, 6 DISSOLVING PROCESS USING CaCl_2/MeOH AS THE SOLVENT

A discussion of the mechanism of nylon 6, 6 dissolving process using CaCl_2/MeOH as the sol-vent is presented. The calcium chloride forms a complex compound with nylon 6, 6 by breakingthe hydrogen bonds. The melting point of the CaCl_2 --nylon 6, 6 complex was found to be reducedby 91K relative to the pure nylon 6, 6 polymer. The role of methanol is somewhat similar to acatalyst. The results demonstrate that the complexation of a Lewis acid (CaCl_2) and a Lewis base(nylon 6, 6) can be used to probe intermolecular interactions such as hydrogen bonding in polymers, to modify the polymer properties and mediate its solubility and processing.

Oxidation Modification of Polyacrylonitrile-Based Carbon Fiber and Its Electro-Chemical Performance as Marine Electrode for Electric Field Test

A novel sensor for ocean electric field testing has been fabricated by polyacrylonitrile-based on carbon fibers with electro-chemical oxidation.The surface profile characteristics of the carbon fibers were characterized by scanning electron microscope,Fourier transform infrared spectra and contact angle.Cyclic voltammetry and Tafel curves have been used to study its electro-chemical performances.Two identical electrodes in sea water as the electric field sensor will swiftly respond to applied electric field which causes positive and negative ions to move in opposite direction,resulting in a electric potential difference(ΔE).Test result indicates that the offset potential is typically below 1 m V with a drift of 60-170μVd^-1.Typical self noise level is 1.07 nV√Hz^(1/2)@1 Hz.The electric field response indicates that the modified electrode pair shows better response to AC sine signal of amplitude and frequency(5 mV and 1 mHz)respectively than its blank.The electric field response model of the modified electrodes is creatively presented according to its electric double layer capacitance and Faraday pseudo-capacitance.Many advantages of the carbon fiber electric field electrode will make it have potential application prospect.

Numerical Modelling of Dissolving and Driving Exploitation of Potash Salt in the Qarhan Playa——A Coupled Model of Reactive Solute Transport and Chemical Equilibrium in a Multi-component Underground Brine System

Firstly, the macroscopic chemical equilibrium state of a series of chemical reactions between intercrystal brine and its media salt layer （salt deposit） in Qarhan Salt Lake was studied by using the Pitzer theory. The concept of macroscopic solubility product and its relation with accumulated ore dissolving ratio were presented, which are used in the numerical model of dissolving and driving exploitation of potassium salt in Qarhan Salt Lake. And secondly, with a model forming idea of transport model for reacting solutes in the multi-component fresh groundwater system in porous media being a reference, a two-dimensional transport model coupled with a series of chemical reactions in a multi-component brine porous system （salt deposits） was developed by using the Pitzer theory. Meanwhile, the model was applied to model potassium/magnesium transport in Qarhan Salt Lake in order to study the transfer law of solid and liquid phases in the dissolving and driving process and to design the optimal injection/abstraction strategy for dissolving and capturing maximum Potassium/ Magnesium in the mining of salt deposits in Qarhan Salt Lake.

Dissolving of Nb and Ti carbonitride precipitates in microalloyed steels

The dissolving behaviour of Nb and Ti carbonitride precipitates inmicroalloyed steels during isothermal holding at 1300℃ was investigated by Transmission electronmicroscopy (TEM) and energy dispersion x-ray spectrum (EDX). It was found that all precipitates inNb-Ti microalloyed steel are (Nb, Ti)(C, N). With holding time increasing, the atomic ratio of Nb/Tiin precipitates decrease gradually. These precipitates still existe even after holding for 48 h at1300℃ while Nb(C, N) precipitates dissolve away in Nb microalloyed steel only after 4 h at the sametemperature. These results show that formation and thermostability of precipitates are considerablyinfluenced by interaction between Nb and Ti.

Upgrading Paper-grade Softwood Kraft Pulp to Dissolving Pulp by Cold Caustic Extraction

Cold caustic extraction has potential applications in the production of dissolving-grade pulps due to its ability to selectively remove hemicellulose from lignocellulosic materials. In this study,we demonstrate the conversion of paper-grade kraft pulp into dissolving pulp by a single-stage cold caustic extraction. Under the extraction conditions of 12 wt% NaOH lye,11% pulp consistency,a temperature of 35℃,and 2 h,a paper-grade softwood kraft pulp was purified to high-grade dissolving pulp with 97. 1% α-cellulose content,1. 2% pentosane content,and narrowed molecular weight distribution. The resulting extraction filtrate was concentrated by nano-filtration to obtain the hemicellulose content of 59. 0 g / L,while the permeate was a clear Na OH solution with 10. 9 wt% concentration. A process configuration was also proposed,integrating this cold caustic extraction process with existing pulp and paper production and multi-purpose utilization of the extraction filtrate.

pH-activatable oxidative stress amplifying dissolving microneedles for combined chemo-photodynamic therapy of melanoma

Photodynamic therapy(PDT)-mediated oxidation treatment is extremely attractive for skin melanoma ablation,but the strong hydrophobicity and poor tumor selectivity of photosensitizers,as well as the oxygen-consuming properties of PDT,leading to unsatisfactory therapeutic outcomes.Herein,a tumor acidic microenvironment activatable dissolving microneedle(DHA@HPFe-MN)was developed to realize controlled drug release and excellent chemo-photodynamic therapy of melanoma via oxidative stress amplification.The versatile DHA@HPFe-MN was fabricated by crosslinking a self-synthesized protoporphyrin(PpIX)-ADH-hyaluronic acid(HA)conjugate HA-ADH-PpIX with“iron reservoir”PA-Fe 3+complex in the needle tip via acylhydrazone bond formation,and dihydroartemisinin(DHA)was concurrently loaded in the hydrogel network.HA-ADH-PpIX with improved water solubility averted undesired aggregation of PpIX to ensure enhanced PDT effect.DHA@HPFe-MN with sharp needle tip,efficient drug loading and excellent mechanical strength could efficiently inserted into skin and reach the melanoma sites,where the acidic pH triggered the degradation of microneedles,enabling Fe-activated and DHA-mediated oxidation treatment,as evidenced by abundant reactive oxygen species(ROS)generation.Moreover,under light irradiation,a combined chemo-photodynamic therapeutic effect was achieved with amplified ROS generation.Importantly,the Fe-catalyzed ROS production of DHA was oxygen-independent,which work in synergy with the oxygen-dependent PDT to effectively destroy tumor cells.This versatile microneedles with excellent biosafety and biodegradability can be customized as a promising localized drug delivery system for combined chemo-photodynamic therapy of melanoma.

The Phenomenon of Proton Dissolving in Vacuum and of Proton Condensation from Vacuum. Two Forms of Protons, Structure of Nuclei, Electrons and Atoms

It was investigated how react molecular clusters in water, starch, bio-matrices, polymers and in quartz on gravitation radiation from planets. Gravitation radiation (GR) was found to influence the proton jumping in hydrogen bonds that stabilize the cluster structure. There was given a method calculating parameters of GR as well as a mechanism of its resonance interaction with weak GR from molecular matter (WGR). WGR has been defined as the result of proton dissolving in vacuum connected with its simultaneous condensation in the nearest free space. Both dissolving and condensation proceed with super light velocity. The gravitation wave length has been determined experimentally and it depends on the planet masses (between Earth and Sun λ ≥ 62 km, between Earth and Milky Way center λ ≥ 330 km). GR has been characterized with super light velocity. After analyzing the Sun influence on water two forms of protons were found: in a condensed and dissolved state. A new model for the atomic nucleus has been suggested according to which the protons in the nucleus oscillate between condensed and dissolved state, where in the case of isotopes this state is partially destroyed. The models for H2 and Be shall be given. Electron orbitals in atoms and molecules were found to be caused by a stationary front of shock waves from condensing protons.

Identification and Practical Application of Silicate-dissolving Bacteria

Slime-forming bacteria were isolated from soils, rock surface and earthworm intestine, and their effects on dissolving silicate minerals and tomato growth were examined. One of the bacteria, Bacillus mucilaginosus RGBc13, had particularly strong ability to form slime and dissolve silicates. RGBc13 could also colonize and develop in both non-rhizosphere and rhizosphere soil. Total number of slime-forming bacteria increased from 2.9 × 103 cfu·g-1and 8.4 × 103 cfu·g-1 to 9.6 × 106 cfu·g-1 and 6.0 × 107 cfu·g-1 in the non-rhizosphere and rhizosphere soils respectively. Potassium and phosphorus nutritional conditions in the rhizosphere were markedly improved through inoculation of this bacterium. Available K and P respectively increased from 25. 86 and 3. 63mg · kg-1 in the non-rhizosphere soil to 91. 23 and 5. 74mg · kg-1 in the rhizosphere soil. Tomato biomass increased by 125%, K and P uptakes were more than 150%, greater than the non-inoculation. Thus, there is a potential in applying RGBcl3 for improving plant K and P nutrition.

The Conditions of Releasing Potassium by a Silicate- dissolving Bacterial Strain NBT

The potassium-releasing characteristics of a bacterium from different minerals were studied through pure culture and soil column experiments. The results showed that the strain NBT of tested strains had the highest potassium-releasing capacity. It released 35.2 mg/L after 7days of pure culture incubation at 28@, 31.8% - 1203.7% more than other tested strains. Potassium released from the minerals was obviously affected by pH, aerobic condition, soil and mineral properties. The strain NBT had a much higher potential to release potassium in the pH 6.5-8.0 than other pHs. Living cell inoculation resulted in an increase of 84.8% -127.9% compared with that of the dead cell inoculation. More aerobic condition produced more K than a less aerobic one. The potassium-releasing order was as follows: illite>feldspar>muscovite. Soil column experiment showed that the bacterial number increased from (2.6 - 3.0) × 106/g to (6.8 - 7.4) × 107/g. Soil available potassium content increased by 31.2 - 33.6mg/kg in yellow-brown soil and 21.7mg/kg in paddy soil, when inoculated with the strain NBT, 290.6% and 185.5% increment of the dead cell inoculation soils respectively.