Microstructural evolution in electroformed nickel shaped-charge liners with nano-sized grains undergone deformation at ultrahigh strain rate

Nickel shaped-charge liners with nano-sized grains were prepared by the electroforming technique, and the deformation at ultrahigh strain rate was performed by explosive detonation. The as-formed and post-deformed microstructures of electroformed nickel shaped-charge liners with nano-sized grains were observed by means of transmission electron microscopy, and the orientation distribution of the grains was analyzed by the electron backscattering pattern （EBSP） technique. The melting phenomenon in the jet fragment and the recovery and recrystallization in the slug after plastic deformation at ultrahigh-strain rate were observed in the ultrafine-grained nickel shaped-charge liners. The research evidence shows that dynamic recovery and recrystallization play an important role in plastic deformation at ultrahigh strain rate.

Electroforming of a Complex Mould Using an Acid-Mediated Copper Sulphate Bath

This work reports a procedure for the fabrication of a complex mould using the technique of electroforming. This was with a view to finding a cheaper and less labour-intensive mould production route practicable locally. A Plaster of Paris electroforming mandrel in the shape of a water bottle was produced and made electrically conducting with a layer of copper conducting paint. Considerations for electroform removal were made by applying a thin, chloroform-dissolvable epoxy layer beneath the conducting copper paint. Uniformity of deposition on the mandrel was accomplished with the construction of a special deposition bath with multiple copper anodes around its perimeter. The electroforming was done in the galvanostatic electro deposition mode for about 240 hrs in a 1 M Cu2SO4 bath with the deposition of elemental copper on the mandrel. Incidences of rising bath pH were mediated with concentrated H2SO4. A free-standing electroform representing the mould cavity was formed in the deposition. The product so formed was a reproduction of the net-shape of the mandrel exhibiting smooth surface finish. The electroforming was cast with an aluminum backing layer to complete its transformation into a split mould. The finished mould was comparable in appearance to the imported moulds in terms of appearance and reproduction of intricate surface patterns. The simplicity and low cost of this method significantly reduced the requirements for expensive instrumentation and highly skilled labour for mould production.

MICROSTRUCTURAL CHARACTERISTICS ASSOCIATED WITH HIGH- STRAIN-RATE PLASTIC DEFORMATION IN THE ELECTROFORMED COPPER LINER OF SHAPED CHARGES

The microstructures of electroformed copper liners of shaped charges that had undergone high-strain-rate deformation were observed by optical microscopy （OM） and scanning electron microscopy （SEM）. Meanwhile, the orientation distribution of the grains in the recovered jet was examined by electron backscattering Kikuchi pattern （EBSP） technique. EBSP analysis reveals that the fibrous texture observed in the as-electroformed copper liners disappeared after explosive detonation deformation. OM observation shows that the microstructure evolves system- atically from the jet center to its perimeter during cooling from high temperatures after explosive detonation deformation. This microstructural characteristic is similar to that of solidification, i.e. there exist equiaxed grains in the center of the jet and significant columnar grains around the equiaxed grains. The result reveals that there is melting-related phenomenon in the jet center. Corresponding microhardness variations from the jet center to its perimeter is also determined. All the phenomena can be explained by a strong gradient of temperature across the section of the jet during plastic deformation at high-strain-rate.

Microstructure and penetration behavior of electroformed copper liners of shaped charges during explosive detonation deformation

The microstructure in the electroformed copper liners of shaped charges prepared with different electrolytes was studied by Scanning Electron Microscopy （SEM） and Electron Backscattering Kikuchi Pattern （EBSP） methods. SEM observations revealed the existence of columnar grains in electroformed copper liners of shaped charges formed by electrolyte without any additive and the average grain size is about 3 μm. When an additive is introduced to the electrolyte, the grains formed in the copper liners become equiaxed and finer. EBSP results show that the columnar grain grown during electroformation has the most preferential growth direction, whereas a micro-texture does not exit in the specimen prepared by electrolyte with the additive. Further, explosive detonation deformation experiments show that penetration depth is dramatically improved when the electroformed copper liners of shaped charges exhibit equiaxed grains.

Orbital-abrasion-assisted Electroforming of Non-rotating Parts

A novel technique of electroforming with orbital moving cathode was carried out for the fabrication of non-rotating thin-walled parts.This technique features a large number of insulating and insoluble hard particles as a real-time polishing to the cathode.When cathode moves,hard particles polish its surface and provide the nickel non-rotating parts with near-mirror finishing.Morphology,microstructure,surface roughness and micro hardness of deposits fabricated by novel method were studied in contrast with the sample produced by traditional electroforming methods.Theoretical analysis and experimental results showed that the novel technique could effectively remove the hydrogen bubbles and nodules,disturb the crystal nucleation,and refine the grains of layer.The mechanical properties were significantly improved over traditional method.The micro-hardness of the layer was in a uniform distribution ranging from 345 HV to 360 HV.It was confirmed that this technique had practical significance to non-rotating thin-walled parts.

Crystal defects formed in electroformed nickel liners of shaped charges

Two types of electroformed nickel liners of shaped charges were prepared by electroforming technique. X-ray diffraction （XRD）, transmission electron microscopy （TEM）, electron backscattering diffraction （EBSD） technique and high resolution electron microscopy （HREM） have been employed to investigate the crystal defects formed in electroformed nickel liners of shaped charges. The result shows that （100） fiber texture which is parallel to the grown direction exists in the electroformed nickel prepared by using direct current electroforming without any additives, and （111） fiber texture exists in the electroformed nickel prepared by using direct current electroforming with additives. The deposits prepared by using direct current electroforming possess columnar grain with an average grain size of 30 μm in width and 170 μm in length. The deposits prepared with additives are composed of a colony structures with grain size of about 29 nm, and a lot of crystal defects such as twins, antiphase boundaries and stacking faults have been observed in the electroformed nickel.

Mechanical properties of electroformed copper layers with gradient microstructure

The electroformed copper layer with gradient microstructure was prepared using the ultrasonic technique. The microstructure of the electroformed copper layer was observed by using an optical microscope （OM） and a scanning electron microscope （SEM）. The preferred orientations of the layer were characterized by X-ray diffraction （XRD）. The mechanical properties were evaluated with a Vicker＇s hardness tester and a tensile tester. It is found the gradient microstructure consists of two main parts： the outer part （faraway substrate） with columnar crystals and the inner part （nearby substrate） with equiaxed grains. The Cu-（220） preferred orientation increases with the increasing thickness of the copper layer. The test results show that the microhardness of the electroformed copper layer decreases with increasing grain size along the growth direction and presents a gradient distribution. The tensile strength of the outer part of the electroformed copper layer is higher than that of the inner part but at the cost of ductility. Meanwhile, the integral mechanical properties of the electroformed copper with gradient microstrucmre are significantly improved in comparison with the pure copper deposit.

Microstructure and texture of electroformed copper liners of shaped charges

The microstructures of copper liners of shaped charges prepared byelectroforming technique were investigated by transmission electron microscopy (TEM). Meanwhile, theorientations distributing of the grains in the electroformed copper liners of shaped charges wasexamined by the electron backscattering Kikuchi pattern (EBSP) technique. TEM observations haverevealed that these electroformed copper liners of shaped charges have the grain size of about 1-3mu m and the grains have a preferential orientation distribution along the growth direction. EBSPanalysis has demonstrated that the as-formed copper liners of shaped charges exhibit amicro-texture, i.e. one type of fiber texture, and the preferred growth direction is normal to thesurface of the liners.

Improvement of thickness deposition uniformity in nickel electroforming for micro mold inserts

Thickness deposition is a crucial issue on the application of electroformed micro mold inserts. Edge concentration effect is the main source of the non-uniformity. The techniques of adopting a non-conducting shield, a secondary electrode and a movable cathode were explored to improve the thickness deposition uniformity during the nickel electroforming process. Regarding these techniques, a micro electroforming system with a movable cathode was particularly developed. The thickness variation of a 16 mm×16 mm electroformed sample decreased respectively from 150% to 35%, 12% and 18% by these three techniques. Combining these validated methods, anickelmold insert for microlens array was electroformed with satisfactory mechanical properties and high replication precision. It could be applied to the following injection molding process.

Abrasive-assisted Nickel Electroforming Process with Moving Cathode

In traditional electroforming process for revolving parts with complex profiles, the drawbacks on surface of deposits, such as pinholes and nodules, will lead to varying physical and mechanical properties on different parts of electroformed components. To solve the problem, compositely moving cathode is employed in abrasive-assisted electroforming of revolving parts with complicated profiles. The cathode translates and rotates simultaneously to achieve uniform friction effect on deposits without drawbacks. The influences of current density and transla- tion speed on the microstructure and properties of the electroformed nickel layers are investigated. It is found that abrasive-assisted electroforming with compound cathode motion can effectively remove the pinholes and nodules, positively affect the crystal nucleation, and refine the grains of layer. The increase of current density will lead to coarse microstructure and lower micro hardness, from 325 HV down to 189 HV. While, faster translational linear speed produces better surface quality and higher micro hardness, from 236 HV up to 283 HV. The weld-ability of the electroformed layers are also studied through the metallurgical analysis of welded joints between nickel layer and 304 stainless steel. The electrodeposited nickel layer shows fine performance in welding. The novel compound motion of cathode promotes the mechanical properties and refines the microstructure of deposited layer.

In situ backscattered electron imaging study of the effect of annealing on the deformation behaviors of Ni electroformed from additive-free and saccharin-containing sulfamate solutions

The Ni samples were electroformed from additive-free(AF) and saccharin-containing(SC) sulfamate solutions, respectively. In situ backscattered electron(BSE) imaging, electron backscatter diffraction(EBSD), and electron-probe microanalysis(EPMA) were used to investigate the effect of annealing on the deformation behaviors of the AF and SC samples. The results indicate that columnar grains of the as-deposited AF sample had an approximated average width of 3 μm and an approximated aspect ratio of 8. The average width of columnar grains of the as-deposited SC sample was reduced to approximately 400 nm by the addition of saccharin to the electrolyte. A few very-large grains distributed in the matrix of the SC sample after annealing. No direct evidence indicated that S segregated at the grain boundaries before or after annealing. The average value of the total elongations of the SC samples decreased from 16% to 6% after annealing, whereas that of the AF samples increased from 18% to 50%. The dislocation recovery in grain-boundary areas of the annealed AF sample was reduced, which contributed to the appearance of microvoids at the triple junctions. The incompatibility deformation between very-large grains and fine grains contributed to the brittle fracture behavior of the annealed SC Ni.

Pulse electroforming of nickel under perturbation of hard particles

Nickel deposits were prepared by pulse electroforming, in which an aluminium alloy cylinder mandrel rotated in hard particles filling between the electrodes. The microstructure and properties of the deposits were studied by contrasting with electroforming using direct current. The results show that the surface of the deposits obtained by pulse electroforming displays more obvious abrasion marks and (200) preferred orientation to that electroformed using direct current at the same average current density. Besides, the deposits represent higher microhardness and better high-temperature corrosion resistance. It is also found that the orientation index of plane (200) and microhardness significantly increase with the reduction of duty cycle of pulse current. During pulse electroforming, the longer off-time and higher peak current density are helpful to strengthening the hard particles’ polishing effect on the surface of deposits and perturbing effect on crystal nucleation of atoms.

PLASTIC DEFORMATION BEHAVIOR OF ELECTROFORMED COPPER LINER OF SHAPED CHARGE AT DIFFERENT STRAIN RATES

The paper deals with different plastic deformation behavior of electroformed copper liner of shaped charge, deformed at high strain rate (about 1×107s-1) and normal strain rate (4×10-4s-1). The crystallographic orientation distribution of grains in recovered slugs which had undergone high-strain-rate plastic deformation during explosive detonation was investigated by electron backscattering Kikuchi pattern technique. Cellular structures formed by tangled dislocations and sub-grain boundaries consisting of dislocation arrays were detected in the recovered slugs. Some twins and slip dislocations were observed in specimen deformed at normal strain rate. It was found that dynamic recovery and recrystallization take place during high-strain-rate deformation due to the temperature rising, whereas the conventional slip mechanism operates during deformation at normal strain rate.

Microstructure of Co-Ni-Al2O3 Composite Coatings by Electroforming

The metal matrix composite coatings of Co-Ni-Al2O3 were studied by electrolytic codeposition of Co-Ni alloys and Al2O3 on a Cu substrate from a sulfamate electrolyte containing Al2O3 particles. It was illustrated from the examined results of SEM, AFM and XRD that surface morphology and microstructure of Co-Ni-Al2O3 coatings appear to be mainly influenced by variations in Co content. The high Co content coatings with hcp lattice structure have a more uniform and fine structure than that of low Co content coatings with fcc lattice structure. The codeposition of Al2O3 particles in Co-Ni alloys can not change the phase structure of solid solution, only affects the growth and orientation of crystal planes and mostly increase the d value of lattice.

Dynamic recrystallization of electroformed copper liners of shaped charges in high-strain-rate plastic deformation

The microstructures in the electroformed copper liners of shapedcharges after high-strain-rate plastic deformation were in-vestigated by transmission electron microscopy(TEM). Meanwhile, theorientation distribution of the grains in the recovered slug wasexamined by the electron backscattering Kikuchipattern(EBSP)technique. EBSP analysis illustrated that unlike theas-formed electro- formed copper liners of shaped charges the grainorientations in the recovered slug are distributed along randomly allthe directions after undergoing heavily strain deformation athigh-strain rate. Optical microscopy shows a typicalrecrystallization structure, and TEM exam- ination revealsdislocation cells existed in the thin foil specimen. These resultsindicate that dynamic recovery and recrystallization occur duringthis plastic deformation process, and the associated deformationtemperature is considered to be higher than 0.6 times the meltingpoint of copper.

Deformation behavior of explosive detonation in electroformed nickel liner of shaped charge with nano-sized grains

Nickel liner of shaped charge with nano-sized grains was prepared by electroforming technique and the ultra-highstrain-rate deformation was performed by explosive detonation.The as-electroformed and post-deformed microstructures of electroformed nickel liner of shaped charge were observed by optical metallography(OM),scanning electron microscopy(SEM) and transmission electron microscopy(TEM) and the orientation distribution of the grains was analyzed by electron backscattering pattern(EBSP) technique.Both melting phenomenon in the jet fragment and recovery and recrystallization in the slug after ultra-high-strain-rate deformation were observed.The research evidence shows that dynamic recovery and recrystallization play an important role in ultra-high-strain-rate deformation for electroformed nickel liner of shaped charge with nano-sized grain.

Microstructure and properties of electroformed nickel under different waveform conditions

In order to prepare electroformed nickel with excellent properties,the effect of different waveforms on microstructure and mechanical properties was investigated by optical microscopy(OM),X-ray diffraction(XRD) and tensile test,respectively.The results show that the samples are composed of micron columnar grains with high-density nanoscale coherent twin boundaries which are parallel to the growth plane.The tensile strength and elongation display opposite tendency with the increase in current density when direct current(DC) electroforming was applied.However,under the condition of pulse current(unidirectional,bidirectional) electroforming,the change regulation of tensile strength and elongation is close while cathode(peak,positive peak) current density increases.XRD results show that electroformed nickel layers with high purity are all fcc crystal configuration under different conditions of the current waveform.The nickel layers formed under bidirectional pulse current behave superior global performance with tensile strength of 692.0 MPa and elongation of 27.6 %.

电化学加工虚拟仿真实验建设与应用

电化学加工现有实验教学以模型演示和装备讲解为主,学生自主学习和实验教学效果较差.基于此,开发完成了"电化学虚拟仿真实验"教学项目,营造逼真的虚拟实验环境,模拟真实电化学加工成材成形过程.学生可以根据需要选择合适的加工方式,掌握具体操作过程和工艺参数,在沉浸式环境下弄清电化学加工由"无形反应"到"有形实物"的工艺过程实质.

微细金属管制造技术现状与研究进展

微细金属管具有微环境下的微通道封闭、定向导向、稳流导流等功能,被广泛应用于医疗、电工电子、传热、光学等领域。受加工工具小型化、尺寸效应对材料性能和摩擦行为的改变等限制,微细金属管的制备极具挑战性。总结了微细金属管常用制备技术的制备原理、特点、制造能力以及优缺点,包括热挤压成形、冷拔成形、无模拉拔成形以及电铸成形,并对微细金属管制造技术的未来发展趋势与研究重点进行了展望。

精细金属掩模板用近零夹杂Invar合金制备技术

Invar合金是制备精细金属掩模板(Fine Metal Mask,简称FMM)的重要基材,其纯净度直接影响FMM的质量以及有机发光二极管(Organic Light EmittingDiode,简称OLED)技术的发展水平。首先概述了FMM的主要制备技术,介绍了对FMM基材Invar合金的质量要求,并对国产Invar合金箔和国外进口Invar合金箔内的夹杂物进行了表征分析。结果表明,国产Invar合金箔的纯净度与进口Invar合金箔相比,仍存在很大的差距,主要体现在夹杂物的尺寸和数量等方面。为实现OLED配套产业全国产化,攻克Invar合金的近零夹杂难题,开发新型制备技术是关键突破点。最后详细论述了超重力技术在Invar合金除杂方面的研究成果和电铸Invar合金箔应用的可行性,并指出超重力技术和电铸技术有望解决近零夹杂金属材料的制备难题。