A real-time operating system （RTOS）, also named OS, is designed based on the hardware platform of MC68376, and is implemented in the electronic control system for unit pump in diesel engine. A parallel and time-base...A real-time operating system （RTOS）, also named OS, is designed based on the hardware platform of MC68376, and is implemented in the electronic control system for unit pump in diesel engine. A parallel and time-based task division method is introduced and the multi-task software architecture is built in the software system for electronic unit pump （EUP） system. The V-model software development process is used to control algorithm of each task. The simulation results of the hardware-in-the-loop simulation system （HILSS） and the engine experimental results show that the OS is an efficient real-time kernel, and can meet the real-time demands of EUP system; The built multi-task software system is real-time, determinate and reliable. V-model development is a good development process of control algorithms for EUP system, the control precision of control system can be ensured, and the development cycle and cost are also decreased.展开更多
The high working junction temperature of power component is the most common reason of its failure. So the thermal design is of vital importance in electronic control unit （ECU） design. By means of circuit simulation...The high working junction temperature of power component is the most common reason of its failure. So the thermal design is of vital importance in electronic control unit （ECU） design. By means of circuit simulation, the thermal design of ECU for electronic unit pump （EUP） fuel system is applied. The power dissipation model of each power component in the ECU is created and simulated. According to the analyses of simulation results, the factors which affect the power dissipation of components are analyzed. Then the ways for reducing the power dissipation of power components are carried out. The power dissipation of power components at different engine state is calculated and analyzed. The maximal power dissipation of each power component in all possible engine state is also carried out based on these simulations. A cooling system is designed based on these studies. The tests show that the maximum total power dissipation of ECU drops from 43.2 W to 33.84 W after these simulations and optimizations. These applications of simulations in thermal design of ECU can greatly increase the quality of the design, save the design cost and shorten design time展开更多
The performance of the electronic unit pump (EUP) diesel engine is studied, it will be used in the integrated powertrain and its multi parameters are controllable. Both the theoretical analysis and experiment research...The performance of the electronic unit pump (EUP) diesel engine is studied, it will be used in the integrated powertrain and its multi parameters are controllable. Both the theoretical analysis and experiment research are taken. A control unit for the fuel quantity and timing in crankshaft domain is designed on this basis and the engine experiment test has been done. For the constant speed camshaft driving EUP system, the fuel quantity will increase as the supply angle goes up and injection timing has no effect. The control precision can reach 1°CA. The full injection timing MAP and engine peak performance curves are made successfully.展开更多
通过开展不同低压供油压力和单泵关键结构参数对多泵一致性的影响研究,获得了多泵供油特性随各参数的变化规律。利用AMESim一维仿真软件建立了电控单体泵(electronic unit pump,EUP)单泵和某8 V柴油机多泵供油系统模型,对比试验数据验...通过开展不同低压供油压力和单泵关键结构参数对多泵一致性的影响研究,获得了多泵供油特性随各参数的变化规律。利用AMESim一维仿真软件建立了电控单体泵(electronic unit pump,EUP)单泵和某8 V柴油机多泵供油系统模型,对比试验数据验证模型的准确性。随后探究了低压供油压力和凸轮转速对单泵及8 V多泵供油系统中同侧4个单体泵的充油压力和供油压力的影响,确定0.6 MPa为最合适的低压供油压力,并获得了各缸供油峰值压力和峰值压力一致性的变化规律。同时研究了单个单体泵主要结构参数对自身和同侧4个单体泵的影响,得到散差随各参数的变化规律。研究结果表明:半锥角和高压油道直径变化时整体散差变动幅度均在0.5%以内;控制阀升程和柱塞直径变化时,喷油量和峰值压力散差波动的幅度分别为2.03%、0.58%和0.93%、0.19%,因此在加工制造时要严格控制控制阀升程和柱塞直径的精度。展开更多
文摘A real-time operating system （RTOS）, also named OS, is designed based on the hardware platform of MC68376, and is implemented in the electronic control system for unit pump in diesel engine. A parallel and time-based task division method is introduced and the multi-task software architecture is built in the software system for electronic unit pump （EUP） system. The V-model software development process is used to control algorithm of each task. The simulation results of the hardware-in-the-loop simulation system （HILSS） and the engine experimental results show that the OS is an efficient real-time kernel, and can meet the real-time demands of EUP system; The built multi-task software system is real-time, determinate and reliable. V-model development is a good development process of control algorithms for EUP system, the control precision of control system can be ensured, and the development cycle and cost are also decreased.
文摘The high working junction temperature of power component is the most common reason of its failure. So the thermal design is of vital importance in electronic control unit （ECU） design. By means of circuit simulation, the thermal design of ECU for electronic unit pump （EUP） fuel system is applied. The power dissipation model of each power component in the ECU is created and simulated. According to the analyses of simulation results, the factors which affect the power dissipation of components are analyzed. Then the ways for reducing the power dissipation of power components are carried out. The power dissipation of power components at different engine state is calculated and analyzed. The maximal power dissipation of each power component in all possible engine state is also carried out based on these simulations. A cooling system is designed based on these studies. The tests show that the maximum total power dissipation of ECU drops from 43.2 W to 33.84 W after these simulations and optimizations. These applications of simulations in thermal design of ECU can greatly increase the quality of the design, save the design cost and shorten design time
文摘The performance of the electronic unit pump (EUP) diesel engine is studied, it will be used in the integrated powertrain and its multi parameters are controllable. Both the theoretical analysis and experiment research are taken. A control unit for the fuel quantity and timing in crankshaft domain is designed on this basis and the engine experiment test has been done. For the constant speed camshaft driving EUP system, the fuel quantity will increase as the supply angle goes up and injection timing has no effect. The control precision can reach 1°CA. The full injection timing MAP and engine peak performance curves are made successfully.
