Er^(3+)-Yb^(3+) Co-Doped Fiber Ring and Line Laser

Er3+-Yb3+ co-doped fiber of 2 m long is used as the laser gain medium. Two fiber lasers with different structures have been set up, one is the line cavity fiber laser with the dielectric mirror being replaced by an all-fiber reflecting mirror,the other is the ring cavity all-fiber laser. Both set-ups have achieved lasing operation at the wavelength of 1.53 μm. Pumped by the 1 064 nm light from all-solid-state Nd ∶YAG laser, the two fiber lasers at 1 530 nm are operational. Their output powers are 7.8 mW and 2 mW with 130 mW and 160 mW pump powers.

All-fiber Based Er^(3+)∶Yb^(3+) Co-doped Fiber Laser

An all-fiber based Er~ 3+ ∶Yb~ 3+ co-doped double clad fiber laser operating at 1550nm is demonstrated. By using 9m long Er~ 3+ ∶Yb~ 3+ co-doped fiber(EYDF) as the gain medium, and using a pair of fiber Bragg gratings as wavelength filters, the line-width of the output laser is as narrow as 0.2nm and the output power is more than 6mW. The fluorescent effect of the laser before its emission is also studied. And it is found that the Er~ 3+ ∶Yb~ 3+ co-doped double-clad fiber laser also exhibits a high gain for Yb~ 3+ transition near 1080nm.

Green and red up-conversion emissions and thermometric application of Er^(3+) -doped silicate glass

The green and red up-conversion emissions centred at about 534, 549 and 663 nm of wavelength, corresponding respectively to the ^2H11/2 → ^4I15/2, ^4S3/2 → ^4I15/2 and ^4F9/2 → ^4I15/2 transitions of Er^3＋ ions, have been observed for the Er^3＋-doped silicate glass excited by a 978 nm semiconductor laser beam. Excitation power dependent behaviour of the up-conversion emission intensity indicates that a two-photon absorption up-conversion process is responsible for the green and red up-conversion emissions. The temperature dependence of the green up-conversion emissions is also studied in a temperature range of 296-673 K, which shows that Er^3＋-doped silicate glass can be used as a sensor in high-temperature measurement.

Spectroscopic Properties of Er^(3+)-Doped TeO_2-WO_3-ZnO-ZnF_2 Glasses

The Er^(3+)-doped TeO_2-WO_3-ZnO-ZnF_2(TWZOF) glasses were prepared. The absorption spectra, 1.5 μm emission spectra and fluorescence lifetimes of Er^(3+), excited at 970 nm, were measured. The J-O parameters Ω_ t (t =2, 4, 6), absorption and emission cross-sections were calculated. The dependence of the 1.5 μm emission intensity, fluorescence lifetime and bandwidth of the Er^(3+) emission upon the contents of ZnF_2 in glass were investigated. In TWZOF glass, Er^(3+) ions had a broad emission profile around 1.5 μm with the maximum FWHM of 83 nm. With the increasing of the content of ZnF_2, the emission intensity at peak wavelength and the fluorescence lifetime of Er^(3+) at 1.5 μm increase.

High index of refraction via quantum interference in a three-level system of Er^3＋-doped yttrium aluminium garnet crystal

A simple three-level system is proposed to produce high index of refraction with zero absorption in an Er^3＋-doped yttrium aluminium garnet （YAG） crystal, which is achieved for a probe field between the excited state 4I13/2 and ground state 4I15/2 by adjusting a strong coherent driving field between the upper excited state 4I11/2 and 4I15/2. It is found that the changes of the frequency of the coherent driving field and the concentration of Er^3＋ ions in the YAG crystal can maximize the index of refraction accompanied by vanishing absorption. This result could be useful for the dispersion compensation in fibre communication, laser particle acceleration, high precision magnetometry and so on.

Influence of Input Pulse Durations on Properties of Er^(3+)/Yb^(3+) Co-doped DCFA

Based on propagation-rate equations, the influence of different input pulse durations on the properties of Er^3＋/Yb^3＋ co-doped double-clad fiber amplifier at dynamic equilibrium was analyzed. The change characteristic of output power sag with pulse duration and repetition rate was shown. Whether single or multichannel input pulses are amplified, the shorter the input pulse duration is, the smaller the power sags of output pulse will be. At low repetition rate, upper gain values（Gupper） of gain swing are almost the same for different input pulse durations, which tend to the small signal gain, but lower gain value（Glower） of short input pulse is larger than that of long input pulse. At highrepetition rate, lower gain value（Glower） approaches to upper gain value（Glower）.

Effects of Ce^(3+) doping on the structure and magnetic properties of Mn-Zn ferrite fibers

Ce3+-doped Mn-Zn ferrite fibers were successfully prepared by the organic gel-thermal decomposition method from metal salts and citric acid. The composition,structure,and magnetic properties of these ferrite fibers were characterized by X-ray diffraction (XRD),scanning electron microscopy (SEM),and vibrating sample magnetometer (VSM). The results show that Mn0.2Zn0.8Fe2-xCexO4 (x = 0-0.04) fibers are featured with an average grain size of 11.6-12.7 nm,with diameters ranging between 1.0 to 3.5 μm and a high ...

Multiphoton process and optical amplification in Er^(3+)-Yb^(3+)-doped fiber pumped by Ti:Al_2O_3 tunable laser at 980-nm band

The .Er3+-Yb3+-doped fiber has a broadened absorption spectrum, which means the pumping sources can work efficiently from 810 to 1100nm. Among them 980nm is the maximum.absorption （10 dB/km） wavelength. By energy transferring and multiphoton process, the visible and ultraviolet radiation occurs when the Er3+-Yb3+-doped fiber is pumped by the laser at 980-nm band. Further researches on the mechanism of the fluorescence of Er3+-Yb3+-doped silica fiber pumped by Ti: A12O3 tunable laser at 980-nm band are helpful

3.6 W compact all-fiber Pr3+-doped green laser at 521 nm

Green semiconductor lasers are still undeveloped,so high-power green lasers have heavily relied on nonlinear frequency conversion of near-infrared lasers,precluding compact and low-cost green laser systems.Here,we report the first Watt-level all-fiber CW Pr3t-doped laser operating directly in the green spectral region,addressing the aforementioned difficulties.The compact all-fiber laser consists of a double-clad Pr3t-doped fluoride fiber,two homemade fiber dichroic mirrors at visible wavelengths,and a 443-nm fiber-pigtailed pump source.Benefitting from>10 MW∕cm2 high damage intensity of our designed fiber dielectric mirror,the green laser can stably deliver 3.62-W of continuous-wave power at∼521 nm with a slope efficiency of 20.9%.To the best of our knowledge,this is the largest output power directly from green fiber lasers,which is one order higher than previously reported.Moreover,these green all-fiber laser designs are optimized by using experiments and numerical simulations.Numerical results are in excellent agreement with our experimental results and show that the optimal gain fiber length,output mirror reflectivity,and doping level should be considered to obtain higher power and efficiency.This work may pave a path toward compact high-power green all-fiber lasers for applications in biomedicine,laser display,underwater detection,and spectroscopy.

Preparation and ASE Spectrum of a Single-Mode Erbium Doped Tellurite Glass Fiber with D-type Cladding Geometry

Based on the host of tellurite glasses, the glass formation, preform manufacture, and fiber fabrication are described. The characterization of amplified spontaneous emission (ASE) from this newly fabricated single-mode Er3+-doped tellurite fibers is also presented. When pumped at 980 nm, a very broad erbium ASE around 1.53 μm was observed. The variations of ASE with fiber length and pumping power are measured and discussed. The output of 2 mW from Er3+-doped tellurite fiber ASE source was obtained under the pump power of 660 mW.

Research on Infrared Emissivity and Laser Reflectivity of Sn_(1−x)Er_(x)O_(2)Micro/Nanofibers Based on First-Principles

Sn_(1−x)Er_(x)O_(2)(x=0%,8%,16%,24%)micro/nanofibers were prepared by electrospinning combined with heat treatment using erbium nitrate,stannous chloride and polyvinylpyrrolidone(PVP)as raw materials.The target products were characterized by thermogravimetric analyzer,X-ray diffrotometer,fourier transform infrared spectrometer,scanning electron microscope,spectrophotometer and infrared emissivity tester,and the effects of Er^(3+)doping on its infrared and laser emissivity were studied.At the same time,the Sn_(1−x)Er_(x)O_(2)(x=0%,16%)doping models were constructed based on the first principles of density functional theory,and the related optoelectronic properties such as their energy band structure,density of states,reflectivity and dielectric constant were analyzed,and further explained the mechanism of Er^(3+)doping on SnO_(2)infrared emissivity and laser absorption from the point of electronic structure.The results showed that after calcination at 600℃,single rutile type SnO_(2)was formed,and the crystal structure was not changed by doping Er^(3+).The calcined products showed good fiber morphology,and the average fiber diameter was 402 nm.The infrared emissivity and resistivity of the samples both decreased first and then increased with the increase of Er^(3+)doping amount.When x=16%,the infrared emis-sivity of the sample was at least 0.71;and Er^(3+)doping can effectively reduce the reflectivity of SnO_(2)at 1.06μm and 1.55μm,when x=16%,its reflectivity at 1.06μm and 1.55μm are 50.5%and 40%,respectively,when x=24%,the reflectivity at 1.06μm and 1.55μm wavelengths are 47.3%and 42.1%,respectively.At the same time,the change of carrier concentration and electron transition before and after Er^(3+)doping were described by first-principle calculation,and the regulation mechanism of infrared emissivity and laser reflectivity was explained.This study provides a certain experimental and theoretical basis for the development of a single-type,light-weight and easily prepared infrared and laser compatible-stealth material.

Mode-locked fiber lasers at 1064 and 910 nm wavelengths using Nd^(3+)-doped silica fiber

Mode-locked lasing operations at 1064 and 910 nm wavelengths are demonstrated,respectively,in two all-fiber laser oscillators using our homemade Nd^(3+)-doped silica fiber(NDF)as the gain medium.The Al3+/Nd^(3+)co-doped silica core glass was fabricated by the modified sol-gel method with 18,300×10^(-6) Nd^(3+)doping concentration.The NDF drawn by the rodin-tube method has a core of 4μm in diameter and a numerical aperture(NA)of 0.14.At 1064 nm,we measure an average laser output power of 18mWwith a pulse duration of 5.75 ps,a pulse energy of 1.14 nJ,and a slope efficiency of 7.2%.Using the same NDF gain fiber of a different length,a maximum average laser output power is 3.1 mW at 910 nm with a pulse duration of 877 ns,a pulse energy of 2.7 nJ,and a slope efficiency of 1.44%.

Generation of 100 nJ pulse,1 W average power at 2μm from an intermode beating mode-locked all-fiber laser

We report on the investigation of intermode beating mode-locked(IBML)pulse generation in a simple all-fiber Tm^3+-doped double clad fiber laser(TDFL).This IBML TDFL is implemented by matching longitudinal-mode frequency between 793 nm laser and TDFL without extra mode locker.The central wavelength of 1983 nm,the fundamental pulse frequency of 9.6 MHz and the signal-to-noise ratio(SNR)of>50 dB are achieved in this IBML TDFL.With laser cavity optimization,the IBML TDFL can finally generate an average output power of 1.03 W with corresponding pulse energy of 107 nJ.These results can provide an easily accessible way to develop compact large-energy,highpower TDFLs.