棒状结构NaGdF_(4):Yb^(3+),Er^(3+)上转换发光性能的研究

以乙二胺四乙酸二钠(EDTD-2Na)为螯合剂,采用水热法合成了棒状结构的NaGdF_(4):Yb^(3+),Er^(3+)纳米粉末。分别借助X射线衍射(XRD)、荧光光谱仪(PL)和扫描显微镜(SEM)对其晶体结构、发光强度和表面形貌进行分析和表征。探究了稀土前驱体、水热温度和水热时间的实验条件对NaGdF_(4):Yb^(3+),Er^(3+)纳米粉末上转换发光强度的影响;研究了氟源和钠源对NaGdF_(4):Yb^(3+),Er^(3+)晶体形貌和上转换发光强度的改善;同时,采用煅烧处理的方法,进一步探究样品的形貌和发光强度收到的影响。实验结果表明NH4F与NaOH作为氟源和钠源及200℃煅烧1 h得到的棒状结构NaGdF_(4):Yb^(3+),Er^(3+)的发光强度最好,色坐标(CIE)绿色发光强度从84%提升到94.88%。

Effect of Er substituting sites on upconversion luminescence of Er^(3+)-doped BaTiO_3 films

Erbium-doped BaTiO3 films on LaNiO3/Si substrates were fabricated by sol-gel method. The crystalline structure, morphologies and upconversion （UC） luminescence properties of films were respectively investigated by X-ray diffraction （XRD）, atomic force microcopy （AFM） and photoluminescence （PL）. The results indicate that both of the microstructure and luminescence are found to be dependent on Er^3＋ substituting sites. The samples with A-site substitution have smaller lattice constants, larger grains and smoother surface than those with B-site substitution. The photoluminescence spectra show that both of the samples have two stronger green emission bands centered at 528 and 548 nm and a weak red emission band centered at 673 nm, which correspond to the relaxation of Er^3＋ from ^2H11/2, ^4S3/2, and ^4F9/2 levels to the ground level ^4I15/2, respectively. Compared with B-site doped films, A-site doped films have a stronger integrated intensity of green emissions and a weaker relative intensity of red emissions. The differences could be explained by the crystalline quality and cross relaxation （CR） process.

Er^(3+)/Yb^(3+)/Pr^(3+):SrLaGaO_(4)晶体的光谱分析及中红外发射增强

采用非化学计量配比的提拉法成功生长出Er^(3+)/Yb^(3+)/Pr^(3+):SrLaGaO_(4)晶体、Er^(3+)/Yb^(3+):SrLaGaO_(4)和Er^(3+):SrLaGaO_(4)晶体并进行了详细的光谱分析,同时对纯的SrLaGaO_(4)晶体进行了热学性能分析。与Er^(3+):SrLaGaO_(4)晶体相比,Er^(3+)/Yb^(3+)/Pr^(3+):SrLaGaO_(4)晶体不仅展示了更好的吸收特性,而且还表现出较弱的近红外发射,以及优异的中红外发射;Er^(3+)/Yb^(3+)/Pr^(3+):SrLaGaO_(4)晶体中2.7μm铒激光下能级4I13/2的荧光寿命显著减少,而上能级4I11/2的寿命略微下降,成功抑制了自终止效应。此外,本工作还研究了Er^(3+)/Yb^(3+)/Pr^(3+):SrLaGaO_(4)晶体中Yb^(3+)的敏化作用和Pr^(3+)离子的去激活作用以及能量传递机制。总之,引入Yb^(3+)和Pr^(3+)有利于在Er^(3+)/Yb^(3+)/Pr^(3+):SrLaGaO_(4)晶体中实现增强的2.7μm发射,这使其成为中红外激光有前途的候选材料。

高热稳定CaGdAlO_(4)∶Er^(3+)/Yb^(3+)荧光粉的上转换发光及其温度传感性能

获得具有良好热稳定性和发光性能的非接触式光学温度传感材料是目前的研究热点之一,本工作通过高温固相法制备了Er^(3+)/Yb^(3+)共掺CaGdAlO_(4)∶Er_(x),Yb_(0.10)(x=0.006、0.008、0.010、0.012、0.014)荧光粉,尺寸大小分布在0.6~4.2μm。在980 nm激光激发下,该荧光粉在500~700 nm发射谱由两个发射带组成,528和550 nm处两个较强的绿光发射带,归属于Er^(3+)的^(2)H_(11/2)→^(4)I_(15/2)、^(4)S_(3/2)→^(4)I_(15/2)能级跃迁,663 nm处较弱的红光发射带,归属于Er^(3+)的^(4)F_(9/2)→^(4)I_(15/2)能级跃迁。上转换发光强度最大组分为CaGdAlO_(4)∶Er_(0.010),Yb_(0.10)。300~573 K变温发射谱表明,基于荧光强度比FIR_(528/550)参数,温度传感绝对灵敏度S_(A)从44.4×10^(-4) K^(-1)(@300 K)先增大到52.0×10^(-4) K^(-1)(@445 K)随后减小到49.0×10^(-4) K^(-1)(@573 K)。相对灵敏度S_(R)则从0.95×10^(-2) K^(-1)(@300 K)单调减小到0.27×10^(-2) K^(-1)(@573 K)。冷热循环实验表明该材料的热重复性优于98%。结果表明,CaGdAlO_(4)∶Er_(0.010),Yb_(0.10)荧光粉在光学温度传感领域具有潜在的应用前景。

LD脉冲泵浦Er^(3+)/Yb^(3+):Lu_(2)Si_(2)O_(7)晶体百kHz激光器

目前1.5μm激光二极管(Laser Diode,LD)泵浦的铒镱共掺玻璃/晶体被动调Q微型激光器广泛应用于激光测距、激光雷达等领域。随着激光器输出重频的增加,玻璃面临突出的热效应问题,晶体的热导率是玻璃的10倍以上,有望能够实现比玻璃基质更高重频的激光输出。报道了一种通过LD脉冲端面泵浦Er^(3+)/Yb^(3+):Lu_(2)Si_(2)O_(7)晶体的百kHz人眼安全激光器。通过实验优化增益介质掺杂浓度和长度、泵浦光斑尺寸和调Q晶体初始透过率等实验参数,同时适当缩短脉宽,优化泵浦占空比,提高了输出重频的稳定性。最终获得了重频为100 kHz、单脉冲能量0.7μJ、脉冲宽度240 ns、光束质量M^(2)=1.61的1537 nm脉冲激光输出。实现了输出脉冲频率与泵浦的一致,保证了输出重频的稳定性,有效解决了输出重频具有随机性、不稳定、不可控等问题。

3μm波段Er^(3+)∶ZBLAN光纤激光器研究进展及展望

3µm激光处于分子指纹区,在医疗外科、气体检测、军事应用等领域都有重要的应用价值。Er^(3+)∶ZBLAN光纤激光器具有效率高、可集成的优点,是3µm激光的主要输出方式。本文从铒离子跃迁产生3µm激光出发,围绕Er^(3+)∶ZBLAN光纤激光器,介绍了3µm激光产生的结构原理及能级系统,总结了实现该波段高功率连续输出和脉冲输出的技术方案和研究进展,重点介绍了基于不同材料可饱和吸收体的调Q和锁模激光器实验研究,并对目前实现3µm波段高功率输出需要解决的问题进行了分析,最后对Er^(3+)∶ZBLAN激光器的发展方向进行了展望。

KYb_(2)F_(7):2%Er^(3+)荧光材料的制备、发光机制及温度传感性能

采用简易水热法制备了正交相KYb_(2)F_(7):2%Er^(3+)上转换荧光材料。利用X射线衍射仪和扫描电子显微镜确定所合成样品均为六角状纯相材料。在980 nm激光激发下,KYb_(2)F_(7):2%Er^(3+)荧光材料展现了位于527 nm和545 nm的两个绿光发射峰和位于655 nm处的红光发射峰,且上转换发光出现少见的以红光为主的现象。变温光谱结果表明,545 nm和655 nm处的发射强度随温度升高均呈现热猝灭。基于热耦合测温原理,对Er^(3+)的^(2)H_(11/2)→^(4)I_(11/2)和^(4)S_(3/2)→^(4)I1_(1/2)两个热耦合能级进行温度传感性能研究,计算了发光温度计的发光强度比(LIR)、绝对灵敏度(S_(a))、相对灵敏度(S_(r))、温度不确定度(δ_T)和可重复度(R),其中最大相对灵敏度在313 K时为0.99%·K^(-1),最小温度不确定度在313 K时为0.73 K,可重复度超过99%,确保了该温度计的可靠性。实验结果表明KYb_(2)F_(7):2%Er^(3+)荧光材料在温度传感方面具有潜在应用价值。

不同激发波长下NaLaF_(4):Er^(3+)/Yb^(3+)的上转换光谱调控研究

为探究不同激发波长(980 nm、1 550 nm)对NaLaF_(4):Er^(3+)/Yb^(3+)上转换发光材料光谱调控的规律和机理,采用水热-固相两步反应法合成一系列不同Er^(3+)/Yb^(3+)掺杂浓度的NaLaF_(4)荧光粉。利用X射线衍射仪(XRD)、荧光分光光度计对材料进行测试,分析其发光性能与机理。结果表明,样品在980 nm激发下呈绿色发光,上转换发光强度随Er^(3+)/Yb^(3+)掺杂浓度增加而呈现先增后减的规律,该发光过程为双光子过程;而在1 550 nm激发下呈红色发光,上转换发光强度随Er^(3+)掺杂浓度增加而呈增强趋势,但随Yb^(3+)浓度增加而降低,发光过程为三光子过程。因此,通过调节激发光波长,在同组分NaLaF_(4):Er^(3+)/Yb^(3+)荧光粉中实现颜色可控的绿、红色发光,对设计新型光谱调控手段和探索新的发光材料具有一定的理论指导意义。

溶剂热法制备NaScF_(4):Yb^(3+)/Er^(3+)及其发光性能的研究

利用溶剂热法在油酸(OA),正辛醇(OC)及乙二醇(EG)三溶剂中成功制备出NaScF_(4):Yb^(3+)/Er^(3+)纳米颗粒。调节三种溶剂的不同比例观察对样品晶相、结构、尺寸及发光强度的影响。此外,我们使用了X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、荧光光谱仪对样品进行了表征。通过XRD证明在OA、OC、EG分别为16mL,12mL、4mL时成功合成出了纯相的NaScF_(4):Yb^(3+)/Er^(3+)纳米颗粒。SEM图进一步证明样品形貌均匀,分散性较好,粒径较小,颗粒尺寸为37.62±9.36nm。此外,样品的荧光光谱表明样品在980nm激光激发下能发射出红色荧光。因此,该方法下制备的NaScF_(4):Yb^(3+)/Er^(3+)尺寸较小,形貌较均匀,拥有强的红色发射且该材料有望用于生物成像、信息储存,防伪等领域。

Optical temperature sensor based on up-conversion fluorescence emission in Yb^(3+):Er^(3+) co-doped ceramics glass

yb^3＋：Er^3＋ co-doped oxy-fluoride ceramics glass has been prepared. The mechanism of up-conversion emissions about Er^3＋ was discussed, and the temperature properties of green up-conversion fluorescence between 303 and 823 K were investigated. The results show that the sensitivity of this sample reaches its maximum value, about 0.0047 K^-1, when the temperature is 383 K, indicating that this kind of sample can be used as high temperature and high sensitivity optical temperature sensor.

Green and red up-conversion emissions and thermometric application of Er^(3+) -doped silicate glass

The green and red up-conversion emissions centred at about 534, 549 and 663 nm of wavelength, corresponding respectively to the ^2H11/2 → ^4I15/2, ^4S3/2 → ^4I15/2 and ^4F9/2 → ^4I15/2 transitions of Er^3＋ ions, have been observed for the Er^3＋-doped silicate glass excited by a 978 nm semiconductor laser beam. Excitation power dependent behaviour of the up-conversion emission intensity indicates that a two-photon absorption up-conversion process is responsible for the green and red up-conversion emissions. The temperature dependence of the green up-conversion emissions is also studied in a temperature range of 296-673 K, which shows that Er^3＋-doped silicate glass can be used as a sensor in high-temperature measurement.

Spectral and Lasing Properties of Er^(3+0/Yb^(3+) Co-Doped Phosphate Glasses Pumped by LD

Er^3 ＋/Yb^3 ＋ phosphate glasses were fabricated. According to McCumber theory, the stimulated emission cross-section of Er^3＋ ions at 1533 nm was calculated on the basis of absorption spectrum, and 0.84 × 10^-20 cm^2 is derived, the fluorescence lifetime of ^4I13/2 level is 8.5 ms. An Er^3＋/Yb^3＋ co-doped phosphate glass CW laser pumped by LD was demonstrated at room temperature. The maximum output power is 80 mW and slope efficiency is 16.5%.

Preparation and Luminescence of Er^(3+) Doped Oxyfluoride Glass Ceramics Containing LaF_3 Nanocrystals

Er^3＋ doped transparent oxyfluoride glass ceramics version and near infrared luminescence behavior of Er^3＋ in containing LaF3 nanocrystals were prepared and the up-conglasses heat-treating time and temperature, the size （varied from 0 to 19 and glass ceramics were investigated. With increasing nm） and crystallinity （varied from 0 to 47%） of LaF3 nanocrystals in the glass ceramics are increased. The up-conversion luminescence intensity of Er^3＋ ions in the glass ceramics is much stronger than that in the glasses The near infrared emission of Er^3＋ ions in and increased significantly with increasing heat-treating time and temperature the glass ceramics is found to be similar to that in the glasses.

Investigation on Preparation and Fluorescence Properties of Oxy-Fluoride Glass Co-Doped with Er^(3+) and Yb^(3+)

The glass sample based on the composition of 45PbF_2-45GeO_2-10WO_3 co-doped with Yb^(3+)/Er^(3+) was prepared by the fusion method in two steps: melted at 950 ℃ for 20～25 min then annealed at 380 ℃ for 4 h. Through the V-prism it is found that the refractive index of host glass and the sample are 1.517 and 1.65 respectively. The transmittance was observed by using the ultraviolet-visible-infrared spectrometer in the wavelength range from 0.35 to 2.5μm. The transmittance of the host glass is beyond 73%. That of the sample is beyond 50% and there are characteristic absorption peaks of rare-earth ions. The emission spectrum was measured by using the Hitachi F-4500 fluorescent spectrometer pumped by 980 nm semiconductor laser. There are a strong emission peak at 530 nm and a weak peak at 650 nm.

Defect engineering on BiFeO_(3) through Na and V codoping for aqueous Na-ion capacitors

Sodium with low cost and high abundance is considered as a substitute element of lithium for batteries and supercapacitors,which need the appropriate host materials to accommodate the relatively large Na^(+) ions.Compared to Li^(+) storage,Na^(+) storage makes higher demands on the structural optimization of perovskite bismuth ferrite(BiFeO_(3)).We propose a novel strategy of defect engineering on BiFeO_(3) through Na and V codoping for high-efficiency Na^(+) storage,to reveal the roles of oxygen vacancies and V ions played in the enhanced electrochemical energy storage performances of Na-ion capacitors.The formation of the oxygen vacancies in the Na and V codoped BiFeO_(3)(denoted as NV-BFO),is promoted by Na doping and suppressed by V doping,which can be demonstrated by XPS and EPR spectra.By the first-principles calculations,the oxygen vacancies and V ions in NV-BFO are confirmed to substantially lower the Na^(+)migration energy barriers through the space and electric field effects,to effectively promote the Na^(+) transport in the crystals.Electrochemical kinetic analysis of the NV-BFO//NV-BFO capacitors indicates the dominant capacitive-controlled capacity,which depends on fast Na^(+) deintercalation-intercalation process in the NV-BFO electrode.The NV-BFO//NV-BFO capacitors open up a new avenue for developing highperformance Na-ion capacitors.

Up-conversion luminescence properties and energy transfer of Er^(3+)/Yb^(3+)co-doped oxyfluoride glass ceramic containing CaF_2 nano-crystals

The Er^3＋/yb^3＋ co-doped transparent oxyfluoride glass-ceramics containing CaF2 nano-crystals were successfully prepared. After heat treatments, transmission electron microscopy （TEM） images showed that CaF2 nano-crystals of 20-30 nm in diameter precipitated uniformly in the glass matrix. luminescence of Er^3＋ at 540 nm and 658 nm was observed in Comparing with the host glass, high efficiency upconversion the glass ceramics under the excitation of 980 nm. Moreover, the size of the precipitated nano-crystals can be controlled by heat-treatment temperature and time. With the increase of the nano-crystal size, the intensity of the red emission increased more rapidly than that of the green emission. The energy transfer process of Er^3＋ and Yb^3＋ was convinced and the possible mechanism of Er^3＋ up-conversion was discussed.

Optical Spectroscopy of Er^(3+) and Er^(3+)/Yb^(3+)Co-doped Bi_2O_3-GeO_2-B_2O_3-ZnO Glasses

The （60 - x）Bi2O3 - xGeO2-30B2O3-10ZnO （x = 5, 10, 20, 30 molar percent） glasses doped with Er^3＋ and Er^3＋/Yb^3＋ were fabricated using the melting method. The thermal stability of the glasses was studied with their DTA curves. The results show that the difference between the glass transition temperature and the crystallization onset temperature increases with the increase of GeO2 content, indicating that the thermal stability of the glass has become better. The absorption spectra were recorded and the stimulated emission cross sections were calculated using the McCumber theory. The Ω2, O4, and Ω6 parameters,the transition probability, the radiative lifetime, and the fluorescence branch ratio of Er^3＋ for optical transition were calculated from their absorption spectra in terms of reduced matrix U^（t）（λ = 2, 4, 6） character for optical transitions. The infrared emission of Er^3＋ was measured upon excitation with 970 nm light and the full width at half-maximum （FWHM） was estimated from the emission spectra. The pumping efficiency and the intensity of the emission at the 1.54 μm band of Er^3＋ were enhanced considerably by co-doping Yb^3＋ .

新型Al_2O_(3)-CaO-ZnO玻璃制备与Er^(3+)∶2.7 μm中红外发光性能

3 μm波段的中红外光纤激光器在生物医疗、环境监测和军事等领域具有重要的应用前景,在国内外受到了广泛的关注和研究。低声子能量、高效稳定的中红外玻璃作为光纤激光器的核心工作介质,是实现3 μm波段中红外激光的重要基础。本文采用熔融-淬冷法制备了掺Er^(3+)新型Al_2O_(3)-CaO-ZnO玻璃,通过热分析、拉曼光谱、透射光谱以及光致发光光谱等对玻璃的热力学、结构、透过波长范围和中红外发光性能进行了表征。结果表明,Al_(2)O_(3)-CaO-ZnO玻璃具有较高的玻璃化转变温度(~750℃)、较低的声子能量(~780 cm^(-1))以及较宽的透过波长范围(0.5~5 μm);在980 nm激光激发下,在掺Er^(3+)玻璃中观察到了明显的2.7 μm(Er^(3+)∶^(4)I_(11/2)→^(4)I_(13/2))波段荧光发射。研究结果表明Al_(2)O_(3)-CaO-ZnO体系玻璃是一种优良的中红外激光基质材料。

Investigation of Modification Effect of B_2O_3 Component on Optical Spectroscopy of Er^(3+) Doped Tellurite Glasses

To investigate the modification effect of the B2O3 component on tellurite glass, a series of glasses with a composition of xB2O3-（80-x）TeO2-10ZnO-10Na20 （x = 0, 10, 20, 30, 40, 50, 60, 70, 80） and an additional amount of 0.5% Er2Os（in molar） were prepared. The refractive index, the absorption edge of the host, the J-O parameters of Er^3＋ , the fluorescent decay time, the bandwidth, and the quantum efficiency for the 4Ⅰ13/2→4Ⅰ15/2 transition were obtained theoretically and experimentally. These results indicated that the introduction of B2O3 modified the performance of the tellurite glass. For example, with increasing content of B2O3, the refractive index of the host decreases from 1.9 to 1.5, the absorption edge of the host shifted toward the blue regime, the intensity parameter Ω6 changed from 1.08 × 10^-20（for the pure tellurite glass） to 1.98 ×10^-20 cm^2（for the pure borate glass）, the bandwidth of the 4Ⅰ13/2→4Ⅰ15/2 transition increased, and the quantum efficiency of the 4Ⅰ13/2→4Ⅰ15/2 transition decreased.

动态缺陷导致Na_(3)Sc_(2)(PO_(4))_(3):Yb^(3+),Er^(3+)材料上转换和下转移发光不同热猝灭行为研究

掺Eu^(2+)的离子导体Na_(3)Sc_(2)(PO_(4))_(3)具有优异的抗热猝灭性能,是一种很有前景的大功率照明用发光材料。然而,其负热猝灭机理仍有待深入研究。本文以Yb^(3+)/Er^(3+)的f-f跃迁上转换和下转移窄带发射而非更易受干扰的Eu^(2+)d-f跃迁发射为研究对象,旨在获得更清晰的机理。结果表明,热致缺陷/离子的动态迁移能促进高温下辐射跃迁和抑制非辐射跃迁,导致上转换发光具有显著的负热猝灭,下转移发光热猝灭较小。其中,布居速率较慢的上转换过程更容易受到时间尺度与之相当的Na^(+)/空位迁移过程的影响。本研究可为理解发光材料热猝灭机制提供另一种视角。