A Temperature-Insensitive Amplified Spontaneous Emission Broadband Source Based on Er-Doped Fiber

To obtain a stable amplified spontaneous emission（ASE） source for complex environment applications, we design an ASE source and study the output power and spectral characteristics under different ambient temperatures.We optimize the structure of the ASE source to flatten the ASE spectrum, and study the output characteristics in terms of output power and optical spectrum under different pump powers. Then the performance of the ASE source is investigated in the temperature range from-18.9°C to 50°C. A stable-power and flat-spectrum ASE source can be obtained by structural optimization and pump control.

Precise determination of characteristic laser frequencies by an Er-doped fiber optical frequency comb

Femtosecond optical frequency combs correlate the microwave and optical frequencies accurately and coherently.Therefore,any optical frequency in visible to near-infrared region can be directly traced to a microwave frequency.As a result,the length unit“meter”is directly related to the time unit“second”.This paper validates the capability of the national wavelength standards based on a home-made Er-doped fiber femtosecond optical frequency comb to measure the laser frequencies ranging from visible to near-infrared region.Optical frequency conversion in the femtosecond optical frequency comb is achieved by combining spectral broadening in a highly nonlinear fiber with a single-point frequencydoubling scheme.The signal-to-noise ratio of the beat notes between the femtosecond optical frequency comb and the lasers at 633,698,729,780,1064,and 1542 nm is better than 30 d B.The frequency instability of the above lasers is evaluated by using a hydrogen clock signal with a instability of better than 1×10^(-13)at 1-s averaging time.The measurement is further validated by measuring the absolute optical frequency of an iodine-stabilized 532-nm laser and an acetylenestabilized 1542-nm laser.The results are within the uncertainty range of the international recommended values.Our results demonstrate the accurate optical frequency measurement of lasers at different frequencies using the femtosecond optical frequency comb,which is not only important for the precise and accurate traceability and calibration of the laser frequencies,but also provides technical support for establishing the national wavelength standards based on the femtosecond optical frequency comb.

Dispersive Nonlinearity in Er-Doped Optical Fiber

Optical dispersive nonlinearities in Er-doped optical fiber are discussed and measured at the third window wavelength 1.55 μm for optical communications firstly. The experimental method, which is developed by us, is based on dynamic scanning for fixed-point-interference (DSFPI) of two fiber beams. The real part and complex value of the third-order susceptibility at the wavelength are also obtained from the measured Kerr coefficient and nonlinear-absorption coefficient reported elsewhere.

Using Reduced Graphene Oxide to Generate Q-Switched Pulses in Er-Doped Fiber Laser

Using the reduced graphene oxide（rGO） as a saturable absorber（SA） in an Er-doped fiber（EDF） laser cavity,we obtain the Q-switching operation. The rGO SA is prepared by depositing the GO on fluorine mica（FM） using the thermal reduction method. The modulation depth of rGO/FM is measured to be 3.2%. By incorporating the rGO/FM film into the EDF laser cavity, we obtain stable Q-switched pulses. The shortest pulse duration is3.53 μs, and the maximum single pulse energy is 48.19 nJ. The long-term stability of working is well exhibited.The experimental results show that the rGO possesses potential photonics applications.

Observation of 550 MHz passively harmonic mode-locked pulses at L-band in an Er-doped fiber laser using carbon nanotubes film

We demonstrate a passively harmonic mode-locked（PHML） fiber laser operating at the L-band using carbon nanotubes polyvinyl alcohol（CNTs-PVA） film. Under suitable pump power and an appropriate setting of the polarization controller（PC）, the 54^（th） harmonic pulses at the L-band are generated with the side mode suppression ratio（SMSR） better than 44 dB and a repetition frequency of 503.37 MHz. Further increasing the pump power leads to a higher frequency of 550 MHz with compromised stability of 38.5 dB SMSR. To the best of our knowledge, this is the first demonstration on the generation of L-band PHML pulses from an Er-doped fiber laser based on CNTs.

Chirp Extraction of Self-Similar Pulses in a Passively Mode-Locked Er-doped Fiber Laser

In this paper, we adopt cloud computing in a specific scientific computing field for its virtualization, distribution and dynamic extendibility as follows: We obtain high-energy parabolic self-similar pulses by numerical simulation using our non-distributed passively mode-locked Er-doped fiber laser model. For researching characteristics of these wave-breaking-free self-similar pulses, chirp of them must be extracted. We propose several time-frequency analysis methods adopted in chirp extraction of ultra-short optical pulses for the first time and discuss the advantages and disadvantages of them in this particular application.

Double Clad Er-doped Fiber Amplifier

Presented is a theoretical study of double-clad Er-doped fiber power amplifier(EDFA). Two kinds of double clad fibers(DCF) with rectangular and "flower" inner clad shapes are studied, and these fibers have different coupling constants and propagation losses. We calculate the effective pump power absorption ratio along the fiber with different coupling constants from the first cladding to the doped core and with different propagation losses for the power in the inner cladding. Then the gains of the double clad Er-doped fiber amplifiers versus fiber lengths are calculated using the EDFA model based on propagation and rate equations of a homogeneous, two-level medium.

Numerical Simulation on Broad-band Er-doped Superfluorescent Fiber Source Filter Using Long Period Chirped Fiber Grating

Given is an analysis of broad-band Er-doped superfluorescent fiber source(EDSFS)filter using long period chirped fiber grating by transmission matrix method.For our EDSFS attenuated amplitude demand and the flattened wavelength range demand,proposed are the key factors of designing such filters of high performances.The simulation result demonstrates that such type filters have an enough attenuation to flatten the dramatic increase in output amplified spontaneous emission(ASE)in the wavelength range of 1529nm^1535nm by choosing conformable fiber filter parameters such as chirped degree,original period,induced index change,length of the fiber filter,and then broad-band EDSFS could be achieved.

Preparation and Detection of Extended DNA Fibers of Chinese Cabbage

Abstract [Objective] The paper was to prepare and detect the extended DNA fibers of Chinese cabbage. [Method] Chinese cabbage nuclei was first successfully isolated by chopping young leaves with a blade, then nuclei were lysed by SDS to release DNA, and DNA fibers were dragged and extended with a coverslip. [Result] The results of Fiber-FISH with genomic DNA and 25S rDNA as probes showed that DNA fiber size as long as about 1.93 Mb could be measured and the number of 25S rDNA copies region were estimated to be 258 and 687 in Chinese cabbage genome. DNA fibers prepared by this method showed equally spread parallel thread with clear background, and were suitable for FISH analysis. [Conclusion] The study would accelerate Chinese cabbage genome mapping and organization analysis.

Radiation-induced attenuation self-compensating effect in super-fluorescent fiber source

The compact super-fluorescent fiber source （SFS） output spectra variations at different pump currents and under different dose of gamma-ray radiation were measured and compared respectively. The radiation-induced attenuation （RIA） self-compensating effect in SFS based on photo-bleaching was found and the general mathematic model of SFS output spectra variations was made. The radiation-induced background attenuation （RIBA） at the pump wavelength was identified to be the main cause of the total output power and spectra variations and the variations can then be compensated by active control of the pump power to enhance the self-compensating effect. With closed-loop feedback control of pump current, double-pass backward （DPB） configuration and spectrum re-shaping technology, an SFS prototype was made and tested. The mean-wavelength stability of about 87.4 ppm and output power instability of less than 5% were achieved under up to 200 krad （Si） gamma-ray irradiation.

Mode-Locked Erbium-Doped Fiber Laser Using Vanadium Oxide as Saturable Absorber

A mode-locked erbium doped fiber laser（EDFL） is demonstrated using the vanadium oxide（V2O5） material as a saturable absorber（SA）. The V2O5 based SA is hosted into poly ethylene oxide film and attached on fiber ferule in the laser cavity. It shows 7% modulation depth with 71 MW/cm2 saturation intensity. By incorporating the SA inside the EDFL cavity with managed intra-cavity dispersion, ultrashort soliton pulses are successfully generated with a full width at half maximum of 3.14 ps. The laser operated at central wavelength of 1559.25 nm and repetition frequency of 1 MHz.

Erbium-Doped Zirconia-Alumina Silica Glass-Based Fiber as a Saturable Absorber for High Repetition Rate Q-Switched All-Fiber Laser Generation

We propose and demonstrate a Q-switched erbium-doped fiber laser （EDFL） using an erbium-doped zirconia-alumina silica glass-based fiber （Zr-EDF） as a saturable absorber. As a 16-cm-long Zr-EDF is incorporated into a ring EDFL cavity, a stable Q-switching pulse train operating at 1565？nm wavelength is successfully obtained. The repetition rate is tunable from 33.97？kHz to 71.23？kHz by increasing the pump power from the threshold of 26？mW to the maximum of 74？mW. The highest pulse energy of 26.67？nJ is obtained at the maximum pump power.

Harmonic Dark Pulse Emission in Erbium-Doped Fiber Laser

A harmonic dark pulse generation in an erbium-doped fiber laser is demonstrated based on a figure-of-eight configuration. It is found that the harmonic dark pulse can be shifted from the fundamental to the 5th order harmonic by increasing the pump power with an appropriate polarization controller orientation. The fundamental repetition rate of 2O kHz is obtained at the pump power of 29 m W. The highest pulse energy of 42.6 n3 is obtained at the fundamental repetition rate. The operating frequency of the dark pulse trains shifts to 2nd, 3rd, 4th and 5th harmonic as the pump powers are increased to 34mW, 50mW, 59mW and 137mW, respectively.

E_r^3+-doped Fiber Optical Bistability by Ar^+-laser

s:Under The nonlinear optics condition the all-fiber optical bistability operation has been realized in an all-fiber resonator consisted of Er-dope fiber and optical fiber couplers.The experimental bistability threshold is consistent with the theory.

Nonlinear Optical Fiber Resonator:Optical Fiber Bistability

The linear and nonlinear charecteristics of verious optical riber loop resonators have been processed uniformly using transmission matrix method. It is pointed that in nonlinear operation condition each of those optical fiber loop resonators may be used to make an all-optical fiber bistabillty device.The configuration,charecterictics and threshold of verious Er-doped fiber loop bistability devices have been calculated,analysised, and compared, and the design principle of those devices has been given.

Experimental Observation of Bright and Dark Solitons Mode-Locked with Zirconia-Based Erbium-Doped Fiber Laser

We demonstrate the generation of dark and bright solitons with our homemade zirconia-based erbium-doped fiber and graphene oxide（GO） saturable absorber in anomalous dispersion region.The GO is fabricated using an abridged Hummer＇s method,which is combined with polyethylene oxide to produce a composite film.The film is sandwiched between two optical ferrules and embedded in the laser cavity to enhance its birefringence and nonlinearity.The self-starting bright soliton is easily generated at pump power of 78 mW with the whole length cavity of 14.7 m.The laser produces the bright pulse train with repetition rate,pulse width,pulse energy and central wavelength being 13.9 MHz,0.6 ps,2.74 p J and 1577.46 nm,respectively.Then,by adding the 10 m of single mode fiber into the laser cavity,dark soliton pulse is produced.For the formation of dark pulse train,the measured repetition rate,pulse width,pulse energy and central wavelength are 8.3 MHz,20 ns and 4.98 p J and1596.82 nm,respectively.Both pulses operate in the anomalous region.

Passively Q-Switched Erbium-Doped Fiber Laser with TiSe₂as Saturable Absorber

The TiSe2 nanosheets were prepared by means of ultrasound-assisted liquid phase exfoliation (LPE) and the nonlinear saturable absorption properties were experimentally investigated. The modulation depth, saturation intensity and nonsaturable absorbance of the prepared 1T-TiSe2 SA were 15.7%, 1.28 MW/cm2 and 8.2%, respectively. Taking advantage of the saturable absorption properties of TiSe2-based SA, a passively Q-switched erbium-doped fiber (EDF) laser was systematically demonstrated. The pulse repetition rates varied from 24.50 kHz up to 73.79 kHz with the increasing pump power. The obtained shortest pulse width was 1.31 μs with pulse energy of 79.28 nJ. The system presented merits of low-cost SA preparation, system compactness, superb stability and high competition.

Fiber Grating Ring Laser in All Optical Communication System

Erbium fiber grating ring laser (EFRL) witn an integrated travelling wave and low polarization mode noise is reported. Through modulated experiment of a successful 2.488 Gb/s RZ data, it is shown that the EFRL is a promising alternative to DFB lasers for high-speed transmission applications.

60 nJ, 95 fs environmentally stable Er-doped fiber laser system

We demonstrate here an environmentally stable and extremely compactable Er-doped fiber laser system capable of delivering sub-100-fs temporal duration and tens of nanojoules at a repetition rate of 10 MHz.This laser source employs a semiconductor saturable absorber mirror mode-locked soliton laser to generate seed pulses.A singlemode-fiber amplifier and a double-cladding-fiber amplifier(both with double-pass configuration)are bridged by a divider and used to manage the dispersion map and boost the soliton pulses.By using 64 replicas,pulses with as high as 60 n J energy within 95 fs duration are obtained at 10 MHz,corresponding to 600 kW peak power.

Pump quantum efficiency optimization of 3.5 μm Er-doped ZBLAN fiber laser for high-power operation

976 nm+1976 nm dual-wavelength pumped Er-doped ZBLAN fiber lasers are generally accepted as the preferred solution for achieving 3.5μm lasing.However,the 2μm band excited state absorption from the upper lasing level(^(4 )F_(9/2)→^(4)F_(7/2))depletes the Er ions population inversion,reducing the pump quantum efciency and limiting the power scaling.In this work,we demonstrate that the pump quantum efciency can be efectively improved by using a long-wavelength pump with lower excited state absorption rate.A 3.5μm Er-doped ZBLAN fber laser was built and its performances at diferent pump wavelengths were experimentally investigated in detail.A maximum output power at 3.46μm of~7.2 W with slope efciency(with respect to absorbed 1990 nm pump power)of 41.2%was obtained with an optimized pump wavelength of 1990 nm,and the pump quantum efciency was increased to 0.957 compared with the 0.819 for the conventional 1976 nm pumping scheme.Further power scaling was only limited by the available 1990 nm pump power.A numerical simulation was implemented to evaluate the cross section of excited state absorption via a theoretical ftting of experimental results.The potential of further power scaling was also discussed,based on the developed model.