Accurate Evaluation of Free-form Surface Profile Error Based on Quasi Particle Swarm Optimization Algorithm and Surface Subdivision

Although significant progress has been made in precision machining of free-form surfaces recently, inspection of such surfaces remains a difficult problem. In order to solve the problem that no specific standards for the verification of free-form surface profile are available, the profile parameters of free-form surface are proposed by referring to ISO standards regarding form tolerances and considering its complexity and non-rotational symmetry. Non-uniform rational basis spline（NURBS） for describing free-form surface is formulated. Crucial issues in surface inspection and profile error verification are localization between the design coordinate system（DCS） and measurement coordinate system（MCS） for searching the closest points on the design model corresponding to measured points. A quasi particle swarm optimization（QPSO） is proposed to search the transformation parameters to implement localization between DCS and MCS. Surface subdivide method which does the searching in a recursively reduced range of the parameters u and v of the NURBS design model is developed to find the closest points. In order to verify the effectiveness of the proposed methods, the design model is generated by NURBS and the measurement data of simulation example are generated by transforming the design model to arbitrary position and orientation, and the parts are machined based on the design model and are measured on CMM. The profile errors of simulation example and actual parts are calculated by the proposed method. The results verify that the evaluation precision of freeform surface profile error by the proposed method is higher 10%-22% than that by CMM software. The proposed method deals with the hard problem that it has a lower precision in profile error evaluation of free-form surface.

基于优化算法的Free-form型机床各轴运动方程及其对齿面误差的影响

以No.116铣齿机为例,通过推导传统摇台型机床、Free-form型机床中的坐标变换矩阵,根据运动等效转换的原则,应用最小二乘优化原理,用多项式拟合出Free-form型机床各轴的运动方程。通过算例分析,传统摇台型机床与Free-form型机床中的坐标变换矩阵高度吻合,用各轴运动方程在CATIA软件中虚拟加工出的螺旋锥齿轮齿面与理论齿面上的点的距离在0.009mm以内,且该值可控制在0.00001mm以内,验证了该转换方法的正确性。在此基础上,分析了Free-form型机床各轴运动误差对齿面误差的影响,发现B轴为对齿面影响最大的轴,为提高Free-form型机床的制造精度提供了部分理论依据。

一个应力边界条件下平面弹性问题的Locking-Free有限元方法

用非协调有限元方法解决应力边界条件下平面弹性问题的Locking现象,构造了一个新的四边形单元克服Locking现象,给出了新的非协调有限元格式,证明了此格式的收敛性,并给出了最优的误差估计.

基于F-B NCP函数的可行QP-free算法

本文得到一种可行QP-free算法,引入ε-有效集策略使得每次迭代只需求解规模较小的线性方程组得到迭代方向,且方程组只包含工作集中的约束,其规模较原问题大大减小,同时不进行弧搜索,从而降低了运算量.

A Proper Time Integration with Split Stepping for the Explicit Free-Surface Modeling

Errors due to split time stepping are discussed for an explicit free–surface ocean model. In commonly used split time stepping, the way of time integration for the barotropic momentum equation is not compatible with that of the baroclinic one. The baroclinic equation has three–time–level structure because of leapfrog scheme. The barotropic one, however, has two–time–level structure when represented in terms of the baroclinic time level, on which the baroclinic one is integrated. This incompatibility results in the splitting errors as shown in this paper. The proper split time stepping is therefore proposed in such a way that the compatibility is kept between the barotropic and baroclinic equations. Its splitting errors are shown extremely small, so that it is particularly relevant to long–term integration for climate studies. It is applied to a free–surface model for the North Pacific Ocean.

A LOCKING-FREE ANISOTROPIC NONCONFORMING FINITE ELEMENT FOR PLANAR LINEAR ELASTICITY PROBLEM

The main aim of this article is to study the approximation of a locking-free anisotropic nonconforming finite element for the pure displacement boundary value problem of planar linear elasticity. The optimal error estimates are obtained by using some novel approaches and techniques. The method proposed in this article is robust in the sense that the convergence estimates in the energy and L^2-norms are independent-of the Lame parameter λ.

Meshless analysis of an improved element-free Galerkin method for linear and nonlinear elliptic problems

We first give a stabilized improved moving least squares （IMLS） approximation, which has better computational stability and precision than the IMLS approximation. Then, analysis of the improved element-free Galerkin method is provided theoretically for both linear and nonlinear elliptic boundary value problems. Finally, numerical examples are given to verify the theoretical analysis.

A locking-free anisotropic nonconforming rectangular finite element approximation for the planar elasticity problem

This paper deals with a new nonconforming anisotropic rectangular finite element approximation for the planar elasticity problem with pure displacement boundary condition. By use of the special properties of this element, and by introducing the complementary space and a series of novel techniques, the optimal error estimates of the energy norm and the L^2-norm are obtained. The restrictions of regularity assumption and quasi-uniform assumption or the inverse assumption on the meshes required in the conventional finite element methods analysis are to be got rid of and the applicable scope of the nonconforming finite elements is extended.

Process for improving the ladle free- opening rate for high aluminum steel in continuous casting

Steel 20Mn23AlV is a type of high aluminum steel with a very low ladle free-opening rate. The aluminum composition of 20Mn23AlV ranges from 1.6% to 2.45% ,which is significantly higher than other types of steel. According to the real condition of 40 t ladle in steel-making plant of Baosteel Special Steel Company, previous works show that the key factors affecting the ladle free-opening rate of high aluminum steel in continuous casting are：sand material, accessories baking, ladle nozzle cleaning, the process and amount of adding sand, and the rate of argon stirring during refining. Therefore, improving the ladle filler sand quality, baking all of the raw materials, controlling the addition of ladle filler sand, cleaning the ladle nozzle, and optimizing argon stirring during the refining process can resolve the problem of a low ladle free-opening rate of high aluminum steel caused by the long ladle time of liquid steel.

Development of Debris-free Laser Plasma Sources for EUV Lithography in CIOMP

We have been developing debris-free laser plasma sources for EUV lithography since 1996. Two types of debris-free sources, such as cryogenic target and gas-puff target laser plasma sources, were designed and built up in CIOMP. EUV radiation spectra of the sources with a variety of targets have been obtained by different ways.

Multi-Hop Free Space Optical Communications Using Serial Decode-and-Forward Relay Transmissions

This paper investigates the performance of multi-hop Free Space Optical(FSO) communications using serial Decode-and-Forward(DF) relay transmissions.A statistical model for the optical intensity fluctuation at the receiver due to the combined effects of atmospheric turbulence-induced fading,mis alignment fading and pass-loss is presented.Under given weather and mis alignment conditions,a closed-form analytical expression for the end-to-end outage probability of serial Decode-and-Forward(DF) multi-hop FSO communications is derived.Numerical results show that the serial DF multi-hop transmission is a promising technology to enhance the performance of FSO communications.Moreover,the derived analytical expression can provide close approximations to the simulation results.

基于d-q电流解耦的单相双向AC/DC变换器系统

针对现有的单相双向AC/DC变换器闭环控制策略存在静态误差和控制复杂的问题,此处提出了一种基于正交电流虚构算法的d-q电流解耦控制方法,使系统能实现无静差跟踪。首先分析了单相单级LCL谐振式AC/DC变换器的工作原理,其次构建出交流侧的数学等效模型,根据数学模型引入解耦方程对d-q电流进行解耦。同时,针对d-q变换在单相系统无法直接实现的问题,通过正交电流虚构算法构造出与网侧电流正交的矢量。最后搭建了一台125 W实验样机,验证了所述控制方法能实现无静差跟踪。

Study of measurement and control of free loop of hot steel strip in twin-roll strip casting

In the twin-roll strip casting process, hot cast strips can be broken or tom if the casting speed does not match the rolling speed. Usually, a certain length of hot steel strip is hung freely between the caster and rolling mill to deal with the effect of this speed difference. In this paper,the freely hanging hot steel strip is referred to as the free loop of hot steel strip. Accurately measuring and controlling the height of this free loop is the key factor in maintaining a stable casting operation. Several methods for measuring the loop height of a steel strip are discussed and a method for accurately measuring and controlling the free loop height of hot steel strip is presented. Based on the results of the casting loop quantity change curve, this control method is confirmed to be effective and able to meet the requirements of continuous casting strip production.

Performance Analysis of Outage Probability and Error Rate of Square M-QAM in Mobile Wireless Communication Systems over Generalized α-μ Fading Channels with Non-Gaussian Noise

This paper derives new and exact closed-form expressions for the average symbol error rate(SER) of square M-ary quadrature amplitude modulation(M-QAM) in wireless communication systems over theα-μfading channels subject to an additive non-Gaussian noise. The obtained expressions take into account static and mobile wireless receivers. In addition, a closed-form expression for the outage probability in mobile networks is obtained. Please note that all derived expressions in this paper a valid for integer and non-integer values of the fading parameters. Analytical results are presented to study the impact of noise shaping parameter, severity of fading, and mobility on the average SER. Monte-Carlo simulations results are also provided to validate the accuracy of the analytical results.

EXACT SOLUTION FOR RECTANGULAR SLAB WITH THREE EDGES SIMPLY-SUPPORTED AND OTHER FREE

In this paper,we give all-sided pastic analysis of the rectangular slab with three edges simply-supported and other free.Here we discuss the following four cases:(1)The uniformly distributedload over the area a slab.(2).A concentrated load act at midpoint of free edges slab.(3)A concen-trated load act at the center a slab.(4)The line load act along free edge of slab.

A Steady-State Errors Correction Method for Eliminating Measurement Errors

This paper proposes a steady-state errors correction(SSEC)method for eliminating measurement errors.This method is based on the detections of error signal E(s)and output C(s)which generate an expected output R(s).In comparison with the conventional solutions which are based on detecting the expected output R(s)and output C(s)to obtain error signal E(s),the measurement errors are eliminated even the error might be at a significant level.Moreover,it is possible that the individual debugging by regulating the coefficient K for every member of the multiple objectives achieves the optimization of the open loop gain.Therefore,this simple method can be applied to the weak coupling and multiple objectives system,which is usually controlled by complex controller.The principle of eliminating measurement errors is derived analytically,and the advantages comparing with the conventional solutions are depicted.Based on the SSEC method analysis,an application of this method for an active power filter(APF)is investigated and the effectiveness and viability of the scheme are demonstrated through the simulation and experimental verifications.

Influence of 10-(6-plastoquinonyl) decyltriphenylphosphonium on free-radical homeostasis in the heart and blood serum of rats with streptozotocin-induced hyperglycemia

BACKGROUND It is known that under conditions of tissue tolerance to insulin,observed during type 2 diabetes mellitus(DM2),there is an increased production of reactive oxygen species.Moreover,the free radicals can initiate lipid peroxidation(LPO)in lipoprotein particles.The concentration of LPO products can influence the state of insulin receptors,repressing their hormone connection activity,which is expressed as a reduction of the glucose consumption by cells.It is possible that reduction in glucose concentration during administration of 10-(6-plastoquinonyl)decyltriphenylphosphonium(SkQ1)to rats with DM2 may be related to the antioxidant properties of this substance.AIM To establish the influence of SkQ1 on free-radical homeostasis in the heart and blood serum of rats with streptozotocin-induced hyperglycemia.METHODS To induce hyperglycemia,rats were fed a high-fat diet for 1 mo and then administered two intra-abdominal injections of streptozotocin with a 7-d interval at a 30 mg/kg of animal weight dose with citrate buffer equal to pH 4.4.SkQ1 solution was administered intraperitoneally at a 1250 nmol/kg dose per day.Tissue samples were taken from control animals,animals with experimental hyperglycemia,rats with streptozotocin-induced glycemia that were administered SkQ1 solution,animals housed under standard vivarium conditions that were administered SkQ1,rats that were administered intraperitoneally citrate buffer equal to pH 4.4 once a week during 2 wk after 1-mo high-fat diet,and animals that were administered intraperitoneally with appropriate amount of solution without SkQ1(98%ethanol diluted eight times with normal saline solution).To determine the intensity of free radical oxidation and total antioxidant activity,we used the biochemiluminescence method.Aconitate hydratase(AH),superoxide dismutase,and catalase activities were estimated using the Hitachi U-1900 spectrophotometer supplied with software.The amount of citrate was determined by means of the Natelson method.Real-time polymerase chain reaction was carried out using an amplifier ANK-32.RESULTS It was found that the mitochondrial-directed antioxidant elicits decrease of biochemiluminescence parameter values that increase by pathology as well as the levels of primary products of LPO,such as diene conjugates and carbonyl compounds,which indicate intensity of free radical oxidation.At the same time,the activity of AH,considered a crucial target of free radicals,which decreased during experimental hyperglycemia,increased.Apparently,increasing activity of AH influenced the speed of citrate utilization,whose concentration decreased after administering SkQ1 by pathology.Moreover,the previously applied antioxidant during hyperglycemia influenced the rate of antioxidant system mobilization.Thus,superoxide dismutase and catalase activity,as well as the level of gene transcript under influence of SkQ1 at pathology,were changing to the direction of control groups values.CONCLUSION According to the results of performed research,SkQ1 can be considered a promising addition to be included in antioxidant therapy of DM2.

数字孪生下基于DACS-MFAC的数控机床热误差自适应预测方法

基于现代控制理论的经验建模法,在针对数控机床不同生产工况时,难以建立一种共性的热误差解决方案。探索了在数字孪生框架下以无模型驱动方式实现数控机床热误差自适应预测的研究。首先,建立了机床“热传感-映射-融合与优化-驱动”数字孪生框架,实现热特征信息在数字孪生体中的存储与融合。然后,基于MISO系统的假设条件和动态线性化几何释义,提出了一种不受被控系统任何结构数据影响的热误差无模型自适应控制(MFAC)方法。进一步,基于动态发现概率和自适应步长的DACS-MFAC算法按照一定的周期更新系统参数,实现数字孪生系统下热误差预测值的动态优化。实验结果表明,DACS-MFAC方法具有适应强、精度高、收敛性好等优点。

适用于现场电容器组电容量测量方法——JCB-500型多用途全自动电容电桥的研究

介绍了一种不用拆装连接线就可完成电容器组单台电容器电容量测量的多用途电容电桥及各种条件下的测量、比较试验。结果证明其准确性、可靠性、灵敏度。