Experimental Study of Integration and Polyblends Performance for Improved Mixing-Extruding Machine

One improved mixing-extruding machine was introduced as the second-generation product of the mixing-molding integrated technology. In the extruding system,the conventional single screw extruder was substituted by a special conical twin-screw extruder,resulting in stronger feeding ability,more stable extrusion pressure,and better quality of products. The integrated mathematical model of mixing-extruding process was also established by theoretical derivation and optimization according to the experimental results.Then its accuracy was verified by the influences of the pressure of floating weight and the cooling water temperature of extruder on the mixing-extruding integrated process. The results showed that the changes of both parameters could give rise to the fluctuation of the temperature and apparent viscosity of polyblends, thus further influencing the screw rotation speed.

Continuous Extruding Extending Forming of Semi-solid A2017 Alloy

Continuous extruding/ extending formiug process for A2017 alloy in semi-solid state was proposed through installing extending die at the outlet of shearing- cooling- rolling （SCR） machine. A series of experiments to produce fiat bar of A2017 alloy were carried oat. The forming process, metal flow behavior in die and microstructure and mechanical property of prodacts were investigated. It is shown that if the pouring temperature of melt was higher, the die was filled with semi-solid slurry with low solid fraction and periodical cracks would occur on the product surface ; If its pouring temperature was lower or the preheating temperature of die was lower, semisolid slurry would solidify rapidly and block the die after entering the cavity. The analysis of mass flow trace shows that the semi-solid slurry move forward layer by layer and fills the die extending cavity in radiation manner and the velocity of mass flow in the central area of extending cavity and exit of mould is the maximum, and then decreases gradually from the center to both sides of die wall. By inereasiug the die extending angle, the velocity of mass flow becomes more homogeneous. Under rational process control and die design, the A2017 fiat bar with transverse section of 10 × 50 mm and with good surface and fine equiaxed grains can be obtained by continuous extruding/extending forming process. The product＇s tensile strength and elongation are 420.5 MPa and 14.2% , respectively.

ANALYSIS OF SURFACE CRACK ON FORWARD EXTRUDING BAR DURING AXISYMMETRIC CUP-BAR COMBINED EXTRUSION PROCESS

In this paper, the kinematically admissible velocity field with surface crack on forward extruding bar is put forward during the axisymmetric cup-bar combined extrusion process, in accordance with the results of model experiments.On the basis of velocity field, the necessary condition for surface crack formation on the forward extruding bar is derived, with the help of upper bound theorem and the minimum energy principle. Meanwhile, the relationships between surface crack formation and combination of reduction in area for the part of forward and backward extursions relative residual thickness of billet (T/R0),frictional factor (m) or relative land length of ram and chamber are calculated during the extrusion process. Therefore, whether the surface crack on forward exturding bar occurs can be predicted before extruding the lower-plasticity metals for axisymmetric cup-bar combined extrusion process.The analytical results agree very well with experimental results of aluminium alloy LY12 (ASTM 2024) and LC4 (ASTM 7075).

Chemical and mechanical properties of stainless, environment-friendly, and nonflammable Mg alloys (SEN alloys): A review

This review article provides overall understanding of stainless,environment-friendly,and nonflammable Mg alloys(SEN alloys)recently developed at the Korea Institute of Materials Science.SEN alloys are produced by adding small amounts of Ca and Y(each<1 wt%)into commercial Mg–Al based alloys,resulting in exceptional ignition and corrosion resistances and impressive mechanical properties.Their main advantages of SEN alloys are as follows.(1)A dense multi-oxide layer of SEN alloys comprising MgO,CaO,and Y_(2)O_(3) impedes the outward dispersion of Mg vapor and the inward penetration of O_(2) during oxidation,thereby enhancing the oxidation and ignition resistances.(2)The presence of Ca-and Y-based second-phase particles in SEN alloys can enhance their corrosion resistance because Ca-containing particles prevent the spread of corrosion,and the replacement of Al-containing particles with less noble ones containing Y(e.g.,Al–Mn–Y or Al–Y particles)retards corrosion.(3)The addition of minor amounts of Ca and Y renders excellent mechanical properties due to improved strengthening effects.These enhanced properties are attributed to more pronounced dynamic recrystallization and grain refining behaviors caused by the second-phase particles during extrusion.(4)Despite the presence of various types of second-phase particles,the fatigue properties of SEN9 alloys are similar to those of commercial AZ91 alloys.(5)Simultaneous introduction of Ca and Y suppresses the formation of Mg17Al12 discontinuous precipitates during aging,leading to the enhanced elongation of aged SEN alloys.(6)Adding mischmetal into the SEN9 alloy leads to a six-fold enhancement in extrudability.Consequently,the studies conducted on SEN alloys demonstrate their excellent ignition and corrosion resistances and mechanical properties,which broaden the industrial applications of Mg alloys by addressing their inherent weaknesses.

Development of self-adjusting hydraulic machine for combination forming of upsetting and extruding

In the paper a self-adjusting hydraulic machine for combination forming of upsetting and extruding is systematacially presented in terms of mechanical principle, design principle, machine construction, design of the key components and working routine. The machine is designed with the following features: The lower movable beam is adjusted by the ejecting cylinder, the upper upsetting beam is reset by the backstroke slide rods, and the upsetting cylinders communicate with the gas-liquid accumulators. These features make the machine conformation compact, save both the backstroke cylinder of the upper upsetting beam and the upsetting cylinder of the lower movable beam, and simplify the hydraulic system. Furthermore, the machine can resolve such problems as incomplete filling at the addendum position, microcracks at the dedendum position, greater force and lower die life during precision forging of spur gears.

The roles of stress state and pre-straining on Swift effect for an extruded AZ31 Mg alloy

The Swift effect of Mg alloy is sensitive to initial texture.However,dislocation slip is the main deformation mechanism during torsion of Mg alloy.The underlying relation of Swift effect and dislocation slip is still not clarified.The effect of stress state and pre-straining on Swift effect was studied experimentally during free-end torsion for an extruded AZ31 alloy.The free-end torsion was performed with axial tension and compression stress which is lower than yield stress.It is found that the transition of axial deformation from contraction to elongation occurs when the axial stress changes from negative to positive.The pre-dislocations introduced by pre-tension promote axial shortening during torsion.While the pre-twins introduced by pre-compression are inhibition of axial shortening.The change of axial deformation is attributed to competition between twinning and prismatic slip.The axial shortening of extruded Mg alloy is generated by tensile twinning leading to c-axis strain.In contrast,the axial elongation can be generated by the activation of prismatic slip.The magnitude of axial strain generated by twinning is larger than that by prismatic slip.Moreover,the occurrence of detwinning results in axial elongation at low shear strain.

Preparation and Characterization of Thermoplastic Starch from Sugar Palm (Arenga pinnata) by Extrusion Method

Sugar palm(Arenga pinnata)starch is considered an important renewable,biodegradable,and eco-friendly polymer,which is derived from agricultural by-products and residues,with great potential for the development of biocomposite materials.This research was aimed at investigating the development of TPS biocomposites from A.pinnata palm starch using an extrusion process.Palm starch,glycerol,and stearic acid were extruded in a twin-screw extruder.Scanning electron microscopy(SEM)analysis of TPS showed that the starch granules were damaged and gelatinized in the extrusion process.The density of TPS was 1.3695 g/mL,lower than that of palm starch,and the addition of stearic acid resulted in increased TPS density.X-ray diffraction(XRD)results showed that palm starch had a C-type pattern crystalline structure.The tensile strength,elongation at break,and modulus of elasticity of TPS were 7.19 MPa,33.95%,and 0.56 GPa,respectively.The addition of stearic acid reduced the tensile strength,elongation at break and modulus of elasticity of TPS.The rheological properties,i.e.,melt flow rate(MFR)and viscosity of TPS,were 7.13 g/10 min and 2482.19 Pa.s,respectively.The presence of stearic acid in TPS resulted in increased MFR and decreased viscosity values.The peak gelatinization temperature of A.pinnata palm starch was 70°C,while Tg of TPS was 65°C.The addition of stearic acid reduced the Tg of TPS.The thermogravimetric analysis(TGA)analysis showed that the addition of glycerol and stearic acid decreased the thermal stability,but extended the temperature range of thermal degradation.TPS derived from A.pinnata palm starch by extrusion method has the potential to be applied in industrial practice as a promising raw material for manufacturing bio-based packaging as a sustainable and green alternative to petroleum-based plastics.

Numerical Simulations of Polymer Melt Conveying in Co-Rotating Twin Screw Extruder

The 3 D non isothermal flow of non Newtonian viscous polymer melt in a co rotating twin screw extruder is modeled. The distributions of the velocity, temperature, pressure and the viscous dissipation in the flow domain are presented by using a fluid dynamics analysis package (Polyflow). The numerical results show that the temperatures are high in the intermeshing region and on the screw surface, the maximum pressure and the minimum pressure occur in the intermeshing region, and the flow rate is almost proportional to the screw speed.

EXPERIMENTAL INVESTIGATION ON CHANGE OF COLDWORKING RESIDUAL STRAIN OF HOLE IN ALUMINIUM ALLOY SHEET

An experimental study on degeneration of the coldworking residual strainduring different cyclic loadings is presented. The expenmental results obtained showthat the residual strain of squcezing dislributes under power series law ε= axb overthe horizontal line of the stress on both sides of the cenual hole. and that when the max-imum real stress at the hole is lower than the yield stress of the material. the degeneration of residual strain has a sudden change during cyclic loading, and the closer to thehole side, the more serious the degcneration.

THEORY OF THICK-WALLED SHELLS AND ITS APPLICATION IN CYLINDRICAL SHELL

In this paper, a theory of thick-walled shells is established by means of Hellinger-Reissner's variational principle, with displacement and stress assumptions. The displacements are expanded into power series of the thickness coordinate. Only the first four and the first three terms are used for the displacements parallel and normal to the middle surface respectively. The normal extruding and transverse shear stresses are assumed to be cubic polynomials and to satisfy the boundary stress conditions on the outer and inner surfaces of the shell. The governing equations and boundary conditions are derived by means of variational principle. As an example, a thick-walled cylindrical shell is disscussed with the theory proposed. Furthermore, a photoelastic experiment has been carried out, and the results are in fair agreement with the computations.

在VISUAL LISP环境下圆柱状螺旋弹簧建模的实现

在AUTOCAD的实际应用中,使用常用工具圆柱状螺旋弹簧的建模很难实现,甚至根本无法完成.为了解决这个问题,本文通过编制VISUAL LISP程序来实现.这样,在AUTOCAD环境下该程序不仅可以完成圆柱状螺旋线自动绘图,简化建模的过程,也可以完成使用常用工具建模所不能实现的模型.

Study of glue extrusion after endoscopic N-butyl-2-cyanoacrylate injection on gastric variceal bleeding

AIM:To investigate glue extrusion after endoscopic N-butyl-2-cyanoacrylate injection on gastric variceal bleeding and to evaluate the long-term efficacy and safety of this therapy.METHODS:A total of 148 cirrhotic patients in our hospital with esophagogastric variceal bleeding(EGVB) were included in this study.N-butyl-2-cyanoacrylate was mixed with lipiodol in a 1:1 ratio and injected as a bolus of 1-3 mL according to variceal size.Patients underwent endoscopic follow-up the next week,fourth week,second month,fourth month,and seventh month after injection and then every 6 mo to determine the cast shape.An abdominal X-ray fi lm and ultrasound or computed tomographic scan were also carried out in order to evaluate the time of variceal disappearance and complete extrusion of the cast.The average follow-up time was 13.1 mo.RESULTS:The instantaneous hemostatic rate was 96.2%.Early re-bleeding after injection in 9 cases(6.2%) was estimated from rejection of adhesive.Late re-bleeding occurred in 12 patients(8.1%) at 2-18 mo.The glue cast was extruded into the lumen within one month in 86.1% of patients and eliminated within one year.Light erosion was seen at the injection position and mucosa edema in the second week.The glue casts were extruded in 18 patients(12.1%) after one week and in 64 patients(42.8%) after two weeks.All kinds of glue clumping shapes and colors on endoscopic examination were observed in 127 patients(86.1%) within one month,including punctiform,globular,pillar and variform.Forty one patients(27.9%) had glue extrusion after 3 mo and 28 patients(28.9%) after six months.The extrusion time was not related to the injection volume of histoacryl.Obliteration was seen in 70.2%(104 cases) endoscopically.The main complication was re-bleeding resulting from extrusion.The prognosis of the patients depended on the severity of the underlying liver disease.CONCLUSION:Endoscopic injection of cyanoacrylate is highly effective for gastric varices bleeding.The glue clump shape is correlated with anatomic structure of vessels.The time of extrusion was not related to dosage of the glue.

Effects of single and multi-stage solid solution treatments on microstructure and properties of as-extruded AA7055 helical profile

The effects of single-stage solution treatment(SST),enhanced solution treatment(EST),high-temperature pre-precipitation(HTPP)and multi-stage solution treatment(MST)on the microstructure,mechanical properties and corrosion resistance of the as-extruded 7055 aluminium alloy(AA7055)helical profile were investigated using differential scanning calorimetry(DSC),optical microscopy(OM),scanning electron microscopy(SEM),electron back-scattered diffraction(EBSD)and transmission electron microscopy(TEM).It was observed that EST and MST could promote the dissolution of the second-phase particles compared with the traditional SST,and the intergranular phases were distinctly discontinuously distributed after HTPP and MST.There was obvious difference in the main texture type and texture strength for the alloy after different solid solution treatments.HTPP could improve the corrosion resistance of the alloy by regulating the intergranular phases,but the mechanical properties were severely weakened.While the good corrosion resistance of the alloy could be obtained by MST without obvious strength loss.As a result,the MST is an ideal solid solution treatment scheme for AA7055.

Methane aromatization in the absence of oxygen over extruded and molded MoO_3/ZSM-5 catalysts:Influences of binder and molding method

The influences of binder and molding method on the catalytic performance of methane aromatization in the absence of O2 over MoO3/ZSM-5 catalysts were investigated.SEM,NH3-TPD,FT-IR of adsorbed pyridine,N2 adsorption-desorption,cyclohexane adsorption and XPS were employed to characterize the physical and chemical properties of the catalysts.It was found that SiO2 was a suitable binder for the catalyst due to its appropriate weak acidity.The laminar catalyst comprising of an inert spherical core and a MoO3/ZSM-5 laminar shell with 0.1 0.2 mm in thickness showed a better catalytic performance than the extruded catalyst.The improved activity of the laminar catalyst could be attributed to the easy carbonization of Mo species and the quick removal of reaction products from the catalyst surface.

Low cycle fatigue behavior of the extruded AZ80 magnesium alloy under different strain amplitudes and strain rates

Low cycle fatigue behavior of extruded AZ80 magnesium alloy was investigated under uniaxial tension-compression at different strain amplitudes and strain rates.The results show that the extruded AZ80 magnesium alloy exhibits cyclic hardening at strain amplitudes ranging from 0.4%to 1.0%,the asymmetry of hysteresis loops becomes increasingly obvious when the strain amplitude increases.Higher strain rates correspond to higher stress amplitudes,high mean stresses and short fatigue life.{10–12}extension twins play a role in the cyclic deformation under higher strain amplitudes(0.8%,1.0%).The relationship between total strain energy density and fatigue life can be described by the modified Morrow model.The effect of strain rate on the fatigue life can also be predicted by the model.

Dynamic compressive property and failure behavior of extruded Mg-Gd-Y alloy under high temperatures and high strain rates

For the purpose of investigating the dynamic deformational behavior and failure mechanisms of magnesium under high strain rates,the Split Hopkinson Pressure Bar(SHPB)was used for investigating dynamic mechanical properties of extruded Mg-Gd-Y Magnesium alloy at ambient temperature(300 K),200℃(473 K)and 300℃(573 K)temperature.The samples after compression were analyzed by scanning electron microscope(SEM)and metallographic microscope.Dynamic mechanical properties,crack performance and plastic deformation mechanism of extruded Mg-Gd-Y Magnesium alloy along the extrusion direction(ED)were discussed.The results show that,extruded Mg-Gd-Y Magnesium alloy has the largest dynamic compressive strength which is 535 MPa at ambient temperature(300 K)and strain rate of 2826 s^(−1).When temperature increases,dynamic compressive strength decreases,while ductility increases.The dynamic compression fracture mechanism of extruded Mg-Gd-Y Magnesium alloy is multi-crack propagation and intergranular quasi-cleavage fracture at both ambient temperature and high temperature.The dynamic compressive deformation mechanism of extruded Mg-Gd-Y Magnesium alloy is a combination of twinning,slipping and dynamic recrystallization at both ambient temperature and high temperature.

Effects of Y content and temperature on the damping capacity of extruded Mg-Y sheets

The damping behavior of extruded Mg-xY(x=0.5,1.0,3.0 wt.%)sheets were investigated in detail concerning the effects of Y addition and temperature,and the relationship between damping capacity and yield strength was discussed.At room temperature(RT),with Y content increasing from 0.5%to 3.0%,the damping capacity(Q-1)significantly decreased from 0.037 to 0.015.For all the studied sheets,the relationship between strain amplitude and Q-1 fitted well with the Granato and Liicke(G-L)dislocation damping model.With temperature increased,the G-L plots deviated from linearity indicating that the dislocation damping was not the only dominate mechanism,and the grain boundary sliding(GBS)could contribute to damping capacity.Consequently,the Q-1 increased remarkably above the critical temperature,and the critical temperature increased significantly from 50℃ to 290℃ with increasing Y contents from 0 to 3.0wt.%.This result implied that the segregation of Y solutes at grain boundary could depress the GBS,which was consistent with the recent finding of segregation tendency for rare-earth solutes.The extruded Mg-IY sheet exhibited slightly higher yield strength(Rp0.2)and Q-1 comparing with high-damping Mg-0.6Zr at RT.At an elevated temperature of 325℃,the Mg-IY sheet had similar Q-1 but over 3 times larger Rp0.2 than that of the pure Mg.The present study indicated that the extruded Mg-Y based alloys exhibited promising potential for developing high-performance damping alloys,especially for the elevated-temperature application.

Effect of Replacing Fish Meal with Extruded Soybean Meal on Growth, Feed Utilization and Apparent Nutrient Digestibility of Juvenile White Shrimp(Litopenaeus vannamei)

Extruded soybean meal （ESBM） was evaluated as a protein source for partial replacement of fish meal （FM） in diets of juvenile Litopenaeus vannarnei. In the control diet （Diet 1）, FM protein was replaced with increasing dietary levels of ESBM （4.28%, 8.40%, 12.62%, 16.82%, and 25.26%） at 10%, 20%, 30%, 40%, and 60% levels （Diets 2 to 6, respectively）. An eight-week feeding trial was conducted on 720 juvenile shrimp （0.67 g ± 0.01 g mean initial Weight）, and nutrient digestibility of the six diets was determined. ESBM could replace 20% of FM without causing a significant reduction in growth of shrimp, but other dietary treatments strongly affected whole body composition. Crude protein content of the whole body fed Diet 6 was significantly lower than that fed Diet 2 （P〈0.05）, while crude lipid content of the whole body fed Diet 5 or 6 was significantly higher than that fed Diet 2 （P〈0,05）. Protein digestibilities of Diets 5 and 6 were significantly lower than that of Diet 1 （P〈0.05）. Digestibility of lipids ranged from 96.97% in Diet 6 to 98.34% in Diet 3, whereas dry matter digestibility decreased with increasing replacement level. This study indicates that 20% FM replacement with ESBM in the basic diet containing 40% protein and 30% FM is optimal for juvenile L. vannamei.

A comparison study of Ce/La and Ca microalloying on the bio-corrosion behaviors of extruded Mg-Zn alloys

The influences of Ca and Ce/La microalloying on the microstructure evolution and bio-corrosion resistances of extruded Mg-Zn alloys have been systematically investigated in the current study.Compared with single Ca or Ce/La addition,the Ca-Ce/La cooperative microalloying results in an outstanding grain refinement,because the fine secondary phase particles effectively hinder the recrystallized grain growth.The coarse Ca2Mg6Zn3 phases promote the formation of Ca3(PO4)2 or hydroxyapatite particles during the immersion process and accelerate the dissolution of the corrosion product film,which destroys its integrity and results in the deterioration of anti-corrosive performance.The Ce/La elements can be dispersed within the conventional Mg7Zn3 phases,which reduce the internal galvanic corrosion between Mg matrix and the secondary phases,leading to an obvious improvement of corrosion resistance.Therefore,the Ca-Ce/La cooperative microalloying achieves a homogenous fine-grained microstructure and improves the protective ability of surface film,which will pave a new avenue for the design of biomedical Mg alloys in the coming future.

Numerical Simulation of Viscoelastic Extrudate Swell Through Elliptical Ring Die

The numerical simulation of extrudate swell is significant in extrusion processing.Precise prediction of extrudate swell is propitious to the control of melt flow and the quality of final products.A mathematical model of three-dimensional（3D）viscoelastic flow through elliptical ring die for polymer extrusion was investigated.The penalty function formulation of viscoelastic incompressible fluid was introduced to the finite element model to analyze 3D extrusion problem.The discrete elastic viscous split stress（DEVSS）and streamline-upwind PetrovGalerkin（SUPG）technology were used to obtain stable simulation results.Free surface was updated by updating the streamlines which needs less memory space.According to numerical simulation results,the effect of zero-shear viscosity and elongation parameter on extrudate swell was slight,but with the increase of volumetric flow rate and relax time the extrudate swell ratio increased markedly.Finally,the numerical simulation of extrudate swell flow for low-density polyethylene（LDPE）melts was investigated and the results agreed well with others’work.These conclusions provided quantitative basis for the forecasting extrudate swell ratio and the controlling of extrusion productivity shape.