Fast and Slow Responses of the North Pacific Mode Water and Subtropical Countercurrent to Global Warming

Six coupled general circulation models from the Coupled Model Intercomparison Project Phase 5 (CMIP5) are em-ployed for examining the full evolution of the North Pacific mode water and Subtropical Countercurrent (STCC) under global warming over 400 years following the Representative Concentration Pathways (RCP) 4.5. The mode water and STCC first show a sharp weakening trend when the radiative forcing increases, but then reverse to a slow strengthening trend of smaller magnitude after the radiative forcing is stablized. As the radiative forcing increases during the 21st century, the ocean warming is surface-intensified and decreases with depth, strengthening the upper ocean's stratification and becoming unfavorable for the mode water formation. Moving southward in the subtropical gyre, the shrinking mode water decelerates the STCC to the south. After the radiative forcing is stabilized in the 2070s, the subsequent warming is greater at the subsurface than at the sea surface, destabilizing the upper ocean and becoming favorable for the mode water formation. As a result, the mode water and STCC recover gradually after the radiative forc-ing is stabilized.

Fast-transient techniques for high-frequency DC–DC converters

A 30 MHz voltage-mode controlled buck converter with fast transient responses is presented.An improved differential difference amplifier(DDA)-based Type-III compensator is proposed to reduce the settling times of the converter during load transients,and to achieve near-optimal transient responses with simple PWM control only.Moreover,a hybrid scheme using a digital linear regulator with automatic transient detection and seamless loop transition is proposed to further improve the transient responses.By monitoring the output voltage of the compensator instead of the output voltage of the converter,the proposed hybrid scheme can reduce undershoot and overshoot effectively with good noise immunity and without interrupting the PWM loop.The converter was fabricated in a 0.13μm standard CMOS process using 3.3 V devices.With an input voltage of 3.3 V,the measured peak efficiencies at the output voltages of 2.4,1.8,and 1.2 V are 90.7%,88%,and 83.6%,respectively.With a load step of 1.25 A and rise and fall times of 2 ns,the measured 1%settling times were 220 and 230 ns,with undershoot and overshoot with PWM control of 72 and 76 mV,respectively.They were further reduced to 36 and 38 mV by using the proposed hybrid scheme,and 1%settling times were also reduced to 125 ns.

Fast frequency response of inverter-based resources and its impact on system frequency characteristics

The inertia response and primary frequency regulation capability of synchronous grids are declining owing to the increasing penetration of inverter-based resources. The fast frequency response(FFR) of inverter-based resources is an important mitigation option for maintaining grid security under the conditions of low inertia and insufficient primary frequency response capability. However, the understanding and technical characteristics of the FFR of inverter-based resources are still unclear. Aiming at solving the aforementioned problems, this paper proposes a definition for FFR based on the impact mechanism of FFR on system frequency. The performance requirements of FFR are clarified. Then, the effects of FFR on system frequency characteristics are further analyzed based on steady-state frequency deviation, the initial rate of change of frequency, and the maximum transient frequency deviation. Finally, the system requirements for FFR and its application effects are verified by simulating an actual bulk power grid, providing technical support for subsequent engineering application.

Immediate, Fast, and Overcome Response of the Organism in Response to Energy Osteopathy on the Model of Primary Gonarthrosis (Polyparametric and Statistical Studies)

In 26 patients with confirmed primary verified gonarthrosis(PGA),a clinical and instrumental examination was conducted to evaluate the response energy osteopathy followed by statistical processing of the data.Three types of the body’s response to treatment were identified:immediate,fast,and delayed,which,despite the different informative value of the data of the polyparametric study,allowed judging the effectiveness of the method used.

Solvent-free synthesis of hierarchical Tb^(3+)-doped Yttrium benzene-1,3,5-tricarboxylate metal organic framework nanosheets for fast and highly sensitive fluorescence detection of Fe3+and Cr2O72−ions

Controllable synthesis of luminescent metal-organic frameworks (MOFs) having the merits of ease preparation, outstanding sensitivity and stability is of great significance for exploring their efficient sensing applications. Herein, we report a hierarchical terbium-doped yttrium-benzene-1,3,5-tricarboxylate MOF nanosheet via solvent-free synthetic strategy with a topological structure of MIL-78. The fluorescence property of the hierarchical Tb^(3+)-doped Y-based MOF nanosheets can be tuned by adjusting the molar ratio of Tb^(3+) to Y^(3+) ions, and the Tb_(0.5)Y_(0.5)-MOF nanosheet-like morphology with the optimum characteristic Tb^(3+) ion green emission exhibited great potential acting as fluorescence probe for highly sensitive Fe^(3+) and Cr_(2)O_(7)^(2−) detection. The Tb^(3+)-doped Y-MOF nanosheets show a fast response time of less than 1 s for Fe^(3+) ions. They also have low detection limits of 0.40 and 0.26 µM toward Fe^(3+) and Cr_(2)O_(7)^(2−) ions, respectively, as well as excellent stability. This work paves the way to explore intriguing hierarchical MOF-based luminescent materials for efficient fluorescence sensing applications.

Decomposition of Fast and Slow Cloud Responses to Quadrupled CO_(2)Forcing in BCC–AGCM2.0 over East Asia

In this study,the decomposed fast and slow responses of clouds to an abruptly quadrupled CO_(2)concentration(approximately 1139 ppmv)in East Asia(EA)are obtained quantitatively by using a general circulation model,BCC–AGCM2.0.Our results show that in the total response,the total cloud cover(TCC),low cloud cover(LCC),and high cloud cover(HCC)all increased north of 40°N and decreased south of 40°N except in the Tibetan Plateau(TP).The mean changes of the TCC,LCC,and HCC in EA were–0.74%,0.38%,and–0.38%in the total response,respectively;1.05%,–0.03%,and 1.63%in the fast response,respectively;and–1.79%,0.41%,and–2.01%in the slow response,respectively.By comparison,we found that changes in cloud cover were dominated by the slow response in most areas in EA due to the changes in atmospheric temperature,circulation,and water vapor supply together.Overall,the changes in the cloud forcing over EA related to the fast and slow responses were opposite to each other,and the final cloud forcing was dominated by the slow response.The mean net cloud forcing(NCF)in the total response over EA was–1.80 W m^(–2),indicating a cooling effect which partially offset the warming effect caused by the quadrupled CO_(2).The total responses of NCF in the TP,south China(SC),and northeast China(NE)were–6.74 W m^(–2),6.11 W m^(–2),and–7.49 W m^(–2),respectively.Thus,the local effects of offsetting or amplifying warming were particularly obvious.

Adaptive sliding mode control of petrochemical flare combustion process based on radial basis function network

Steam-assisted combustion elevated flares are currently the most widely used type of petrochemical flares.Due to the complex and variable composition of the waste gas they handle,the combustion environment is severely affected by meteorological conditions.Key process parameters such as intake composition,flow rate,and real-time data of post-combustion residues are difficult to measure or exhibit lag in data availability.As a result,the control methods for these flares are limited,leading to poor control effectiveness.To address this issue,this paper proposes an adaptive sliding mode control method based on the radial basis function(RBF)network.Firstly,the operational characteristics of the petrochemical flare combustion process are analyzed,and a control model for the combustion process is established based on carbon dioxide detection.Secondly,an RBF neural network-based unknown function approximator is designed to identify the nonlinear part of the actual operating system.Finally,by combining the control model of the petrochemical flare combustion and designing the RBF sliding mode controller with its adaptive control law,fast and stable control of the flare combustion state is achieved.Simulation results demonstrate that the designed control strategy can achieve tracking control of the petrochemical flare combustion state,and the adaptive law also accomplishes system identification.

Moisture‑Electric–Moisture‑Sensitive Heterostructure Triggered Proton Hopping for Quality‑Enhancing Moist‑Electric Generator

Moisture-enabled electricity(ME)is a method of converting the potential energy of water in the external environment into electrical energy through the interaction of functional materials with water molecules and can be directly applied to energy harvesting and signal expression.However,ME can be unreliable in numerous applications due to its sluggish response to moisture,thus sacrificing the value of fast energy harvesting and highly accurate information representation.Here,by constructing a moisture-electric-moisture-sensitive(ME-MS)heterostructure,we develop an efficient ME generator with ultra-fast electric response to moisture achieved by triggering Grotthuss protons hopping in the sensitized ZnO,which modulates the heterostructure built-in interfacial potential,enables quick response(0.435 s),an unprecedented ultra-fast response rate of 972.4 mV s^(−1),and a durable electrical signal output for 8 h without any attenuation.Our research provides an efficient way to generate electricity and important insight for a deeper understanding of the mechanisms of moisture-generated carrier migration in ME generator,which has a more comprehensive working scene and can serve as a typical model for human health monitoring and smart medical electronics design.

High Density 3D Carbon Tube Nanoarray Electrode Boosting the Capacitance of Filter Capacitor

Electric double-layer capacitors(EDLCs)with fast frequency response are regarded as small-scale alternatives to the commercial bulky aluminum electrolytic capacitors.Creating carbon-based nanoarray electrodes with precise alignment and smooth ion channels is crucial for enhancing EDLCs’performance.However,controlling the density of macropore-dominated nanoarray electrodes poses challenges in boosting the capacitance of line-filtering EDLCs.Herein,a simple technique to finely adjust the vertical-pore diameter and inter-spacing in three-dimensional nanoporous anodic aluminum oxide(3D-AAO)template is achieved,and 3D compactly arranged carbon tube(3D-CACT)nanoarrays are created as electrodes for symmetrical EDLCs using nanoporous 3D-AAO template-assisted chemical vapor deposition of carbon.The 3D-CACT electrodes demonstrate a high surface area of 253.0 m^(2) g^(−1),a D/G band intensity ratio of 0.94,and a C/O atomic ratio of 8.As a result,the high-density 3D-CT nanoarray-based sandwich-type EDLCs demonstrate a record high specific areal capacitance of 3.23 mF cm^(-2) at 120 Hz and exceptional fast frequency response due to the vertically aligned and highly ordered nanoarray of closely packed CT units.The 3D-CT nanoarray electrode-based EDLCs could serve as line filters in integrated circuits,aiding power system miniaturization.

Combined Wind-Storage Frequency Modulation Control Strategy Based on Fuzzy Prediction and Dynamic Control

To ensure frequency stability in power systems with high wind penetration,the doubly-fed induction generator(DFIG)is often used with the frequency fast response control(FFRC)to participate in frequency response.However,a certain output power suppression amount(OPSA)is generated during frequency support,resulting in the frequency modulation(FM)capability of DFIG not being fully utilised,and the system’s unbalanced power will be increased during speed recovery,resulting in a second frequency drop(SFD)in the system.Firstly,the frequency response characteristics of the power system with DFIG containing FFRC are analysed.Then,based on the analysis of the generation mechanism of OPSA and SFD,a combined wind-storage FM control strategy is proposed to improve the system’s frequency response characteristics.This strategy reduces the effect of OPSA and improves the FM capability of DFIG by designing the fuzzy logic of the coefficients of FFRC according to the system frequency index in the frequency support stage.During the speed recovery stage,the energy storage(ES)active power reference value is calculated according to the change of DFIG rotor speed,and the ES output power is dynamically adjusted to reduce the SFD.Finally,taking the IEEE 39-bus test system as an example,real-time digital simulation verification was conducted based on the RTLAB OP5707 simulation platform.The simulation results showthat theproposedmethodcan improve theFMcapabilityofDFIG,reduce the SFDunder thepremise of guaranteeing the rapid rotor speed recovery,and avoid the overshooting phenomenon so that the systemfrequency can be quickly restored to a stable state.

Rapid operando gas monitor for commercial lithium ion batteries: Gas evolution and relation with electrode materials

Internal gases caused by side reactions are crucial signals for evaluating health and safety states of Li-ion batteries(LIBs)while it is still a great challenge to timely realize accurate monitoring.To address the issues of implanting various gas sensors into commercial batteries,here a novel method is developed to fast operando monitoring gas evolution via equipping non-dispersive infrared multi-gases sensors into a sealed tank,where real commercial batteries with one open end could be settled for operating.The generated CO_(2)concentration is strongly linked with both voltage and temperature,while the concentrations of CH_(4) and C_(2)H_(4) are solely dependent on temperature.As a typical trace gas,evolution behaviors of CO_(2)have been related to 0_(2) generation from LiNi_(o.5)Mn_(0.3)CoO_(2)0_(2) positive electrode,implying stable CO_(2)release below a critical voltage of 4.5 V.By tracking CO_(2)concentration,an increased amount of Li_(2)CO_(3) was monitored on the surface of graphite negative electrode during discharge process at dfferent temperatures and cutoff voltages,which contributes to the component variation of solid electrolyte interfaces.Such operando techniques promise a plaform for well understanding the interaction of side reactions linked with gas evolution between positive and negative electrodes in commercial LIBs.

A high performance adaptive on-time controlled valley-current-mode DC–DC buck converter

This paper presents an AOT-controlled(adaptive-on-time,AOT)valley-current-mode buck converter for portable application.The buck converter with synchronous rectifier not only uses valley-current-mode control but also possesses hybridmode control functions at the same time.Due to the presence of the zero-current detection circuit,the converter can switch freely between the two operating modes without the need for an external mode selection circuit,which further reduces the design difficulty and chip area.The converter for the application of high power efficiency and wide current range is used to generate the voltage of 0.6–3.0 V with a battery source of 3.3–5.0 V,while the load current range is 0.05–2 A.The circuit can work in continuous conduction mode with constant frequency in high load current range.In addition,a stable output voltage can be obtained with small voltage ripple.In pace with the load current decreases to a critical value,the converter transforms into the discontinuous conduction mode smoothly.As the switching period increases,the switching loss decreases,which can significantly improve the conversion efficiency.The proposed AOT controlled valley current mode buck converter is integrated with standard 0.18μm process and the simulation results show that the converter provides well-loaded regulations with power efficiency over 95%.When the circuit switches between the two conduction modes drastically,the response time can be controlled within 30μs.The undershoot voltage is controlled within 25 mV under a large current hopping range.

AC Line Filter Electrochemical Capacitors:Materials,Morphology,and Configuration

Recently,more and more supercapacitors(SCs)have been developed as AC line filter capacitors,which are generally named AC line filter electrochemical capacitors(FECs).Compared to traditional bulky aluminum electrolytic capacitors(AECs),FECs have higher capacity and lower space occupancy,which makes them a strong competitor.However,different from the common SCs for energy storage,it is necessary to consider the frequency response of the SCs for AC line filtering,where the contradiction between frequency response and specific capacitance is a challenge.The researchers have proposed different solutions from the perspective of materials,morphology,and configuration for this challenge.Based on the above background,in this review,we briefly introduce the principle and parameters of AC line filter electrochemical capacitors.We systematically summarize the state-of-the-art progresses of FECs and discuss their possible application and development in the future.The development of FECs can greatly promote the planarization,integration,and miniaturization of filter capacitors,and provide a new solution for the utilization of green and unstable energy.

A comparative study of digital low dropout regulators

Granular power management in a power-efficient system on a chip(SoC)requires multiple integrated voltage regulators with a small area,process scalability,and low supply voltage.Conventional on-chip analog low-dropout regulators(ALDOs)can hardly meet these requirements,while digital LDOs(DLDOs)are good alternatives.However,the conventional DLDO,with synchronous control,has inherently slow transient response limited by the power-speed trade-off.Meanwhile,it has a poor power supply rejection(PSR),because the fully turned-on power switches in DLDO are vulnerable to power supply ripples.In this comparative study on DLDOs,first,we compare the pros and cons between ALDO and DLDO in general.Then,we summarize the recent DLDO advanced techniques for fast transient response and PSR enhancement.Finally,we discuss the design trends and possible directions of DLDO.

A comprehensive aerodynamic-thermalmechanical design method for fast response turbocharger applied in aviation piston engines

Limited by the poor transient response performance of turbochargers,the dynamic performance of aviation piston engines tends to deteriorate.In a bid to enhance the turbocharger’s acceleration capabilities,this study scrutinizes various factors impacting its performance.Based on the operational principles and transient response process of the turbocharger,three types of in-ertiadnamely,aerodynamic inertia(ADI),thermal inertia(TI),and mechanical inertia(MI)d are identified and addressed for design.To begin,this paper pioneers the innovative definition of a method for evaluating the transient response performance of the turbocharger.This method incor-porates the introduction of an ADI parameter,inspired by the definition of MI.Subsequently,a thin-walled volute design with a low Biot number and a lightweight turbine impeller is introduced to reduce the turbocharger’s TI and MI.The simulation results of theflowfield distribution within the volute and diffuser demonstrate the comprehensive design method’s effectiveness in improving gas pressure and temperature distributions in these components.Notably,the pressure distributionfluctuation in the constant moment-of-momentum volute(CMV)is 62.8%lower than that in the constant velocity moment volute(CVMV).The low-TI thin-walled volute not only en-hances the turbocharger’s response speed but also reduces its weight by approximately 40%.The impact of three types of inertia on the engine’s response speed is quantified as follows:ADI(94%)>MI(5%)>TI(1%).This conclusion has been verified through test results of both the turbocharger and the engine.This design method not only significantly improves the turbo-charger’s response performance but also offers valuable insights for the optimal design of other blade mechanical systems.

THERMAL-SENSITIVE BETA-CYCLODEXTRIN-CONTAINING POLY(NISOPROPYLACRYLAMIDE)HYDROGELS CROSSLINKED BY Si—O—Si BONDS—SYNTHESIS,CHARACTERIZATION AND PROLONGING IN VITRO RELEASE OF 5-FLUOROURACIL

A series of novel p（N-isopropylacrylamide） （PNIPAM） hydrogels were synthesized by radical copolymerization of N-isopropylacrylamide （NIPAM） and 3-methacryloxypropyltrimethoxysilane （MPTMS）. The copolymers were then crosslinked through hydrolysis of the siloxane in acetic acid/water mixed solvent. Beta-cyclodextrin （Beta-CD） was introduced into the polymeric networks by condensation of 3-glycidoxypropyltrimethoxysilane derived beta-cyclodextrin （KH560-beta-CD） with MPTMS under acidic condition. These gels were heterogeneous, porous and exhibited fast deswelling kinetics when the temperature was elevated to above lower critical solution temperature （LCST）. The swelling ratios of the gels containing beta-CD at room temperature were higher than that of the normal PNIPAM hydrogel, which was caused by the lower crosslinking density in beta-CD contained gels. In comparison to that of the normal PNIPAM gel, the amount of loaded-drug in the hydrogel containing beta-CD was higher, and the release time of 5-fluorouracil （5-Fu） was prolonged, which was attributed to the formation of inclusion compounds between 5-Fu and beta-CD in gel network.

Microwave-assisted Preparation of Temperature Sensitive Poly(N-isopropylacrylamide) Hydrogel with Improved Responsive Properties

Poly（N-isopropylacrylamide）-based hydrogel was prepared under microwave irradiation The hydrogel thus prepared, comparing with that prepared by thermal heating method, exhibits faster swelling and shrinking kinetics. The improved responsive properties are due to the more heterogeneous and porous networks formed under microwave irradiation.

Metal–organic framework wafer enabled fast response radiation detection with ultra-low dark current

Semiconductive metal–organic frameworks(MOFs)have attracted great interest for the electronic applications.However,dark currents of present hybrid organic–inorganic materials are 1000–10,000 times higher than those of commercial inorganic detectors,leading to poor charge transportation.Here,we demonstrate a ZIF-8(Zn(mim)_(2),mim=2-methylimidazolate)wafer with ultra-low dark current of 1.27 pA·mm^(-2) under high electric fields of 322 V·mm^(-1).The isostatic pressing preparation process provides ZIF-8 wafers with good transmittance.Besides,the presence of redox-active metals and small spatial separation between components promotes the charge hopping.The ZIF-8-based semiconductor detector shows promising X-ray detection sensitivity of 70.82μC·Gy^(-1)·cm^(-2) with low doses exposures,contributing to superior X-ray imaging capability with a relatively high spatial resolution of 1.2 lp·mm^(-1).Simultaneously,good peak discrimination with the energy resolution of~43.78%is disclosed when the detector is illuminated by uncollimated 241Am@5.48 MeVα-particles.These results provide a broad prospect of MOFs for future radiation detection applications.

On Feasible Region of Droop-based Fast Frequency Response Controller Parameters of Wind Turbines

Droop-based fast frequency response(FFR)control of wind turbines can improve the frequency performance of power systems with high penetration of wind power.Explicitly formulating the feasible region of the droop-based FFR controller parameters can allow system operators to conveniently assess the feasibility of FFR controller parameter settings to comply with system frequency security,and efficiently tune and optimize FFR controller parameters to meet frequency security requirements.However,the feasible region of FFR controller parameters is inherently nonlinear and implicit because the power point tracking controllers of wind turbine would counteract the effect of FFR controllers.To address this issue,this letter proposes a linear feasible region formulation method,where frequency regulation characteristics of wind turbines,the dead band,and reserve limits of generators are all considered.The effectiveness of the proposed method and its application is demonstrated on a 10-machine power system.

An efficient technique for recovering responses of parameterized structural dynamic problems

In this article,an effective technique is developed to efficiently obtain the output responses of parameterized structural dynamic problems.This technique is based on the conception of reduced basis method and the usage of linear interpolation principle.The original problem is projected onto the reduced basis space by linear interpolation projection,and subsequently an associated interpolation matrix is generated.To ensure the largest nonsingularity,the interpolation matrix needs to go through a timenode choosing process,which is developed by applying the angle of vector spaces.As a part of this technique,error estimation is recommended for achieving the computational error bound.To ensure the successful performance of this technique,the offline-online computational procedures are conducted in practical engineering.Two numerical examples demonstrate the accuracy and efficiency of the presented method.