The CO_2 adsorption on CaO(001) surface at different coverages from 1/9 monolayer(ML) to 1 ML has been investigated using density functional theory calculations. With the analysis of the most stable adsorption structu...The CO_2 adsorption on CaO(001) surface at different coverages from 1/9 monolayer(ML) to 1 ML has been investigated using density functional theory calculations. With the analysis of the most stable adsorption structures at different coverages, the mechanism of CaO(001)surface carbonating into CaCO_3 has been explored. At low coverages(≤1/3 ML), CO_2 molecule prefers sitting in parallel pattern on the CaO(001) surface, while the structure of the CaO(001)surface remains unchanged. At medium coverage(4/9 ～ 2/3 ML), the repulsive interactions between oxygen atoms of CO_2 become stronger, and the calcium carbonation structure appears on the CaO(001) surface. At high coverage( ≥ 7/9 ML), the structure of the CaO(001) surface is deeply damaged, and a few CO_2 molecules have penetrated into the surface and bound to the O atom of the second layer(sub-surface), eventually forming the layered structure of CaCO_3.Additionally, herein has discussed the simulation of HREELS and thermodynamical stability of these structures at different coverages.展开更多
The Zn and Fe modified /ZrO<sub>2</sub>-Al<sub>2</sub>O<sub>3</sub> catalyst (Zn-Fe-SZA) was prepared and mechanisms of deactivation and methods for regeneration of as-prepared cata...The Zn and Fe modified /ZrO<sub>2</sub>-Al<sub>2</sub>O<sub>3</sub> catalyst (Zn-Fe-SZA) was prepared and mechanisms of deactivation and methods for regeneration of as-prepared catalyst were explored with n-pentane isomerization as a probe reaction. The results indicated that the isopentane yield of the fresh Zn-Fe-SZA-F catalyst was about 57% at the beginning of the run, and declined gradually to 50% within 1500 min, then fell rapidly from 50% to 40% between 1500 and 2500 minutes. The deactivation of Zn-Fe-SZA catalyst may be caused by carbon formation on surface of the catalyst, sulfate group attenuation owing to reduction by hydrogen, removal of sulfur species and the loss of strong acid sites. It was found that the initial catalytic activity over Zn-Fe-SZA-T catalyst was 48%, which recovered by 84.3% as compared to that of fresh catalyst (57%). However, it showed a sharp decrease in isopentane yield from 48% to 29% within 1500 minutes, showing poor stability. This is associated to the loss of acidity caused by removal of sulfur species cannot be basically restored by thermal treatment. Resulfating the calcined catalyst could improve the acidity of catalyst significantly, especially strong acid sites, as compared with the calcined sample. The improved stability of the resulfated catalyst can be explained by: 1) eliminaton of carbon deposition to some extent by calcination process, 2) formation of improved acidic nature by re-sulfation, favoring isomerization on acidic sites, 3) restructuring of the acid and metal sites via the calcination-re-sulfation procedure.展开更多
The interaction of Ag atoms with a defective MgO（001） surface is systematically studied based on density functional theory. The Ag clusters are deposited on neutral and charged oxygen vacancies of the MgO（001） sur...The interaction of Ag atoms with a defective MgO（001） surface is systematically studied based on density functional theory. The Ag clusters are deposited on neutral and charged oxygen vacancies of the MgO（001） surface. The structures of Ag clusters take the shape of simple models of two- or three-dimensional （2D and 3D） metal particles deposited on the MgO surface. When the nucleation of the metal clusters occurs in the Fs （missing neutral O） centre, the interaction with the substrate is considerably stronger than that in the Fs^＋ （missing O-） centre. The results show that the adsorption of Ag atoms on the MgO surface with oxygcn vacancy is stronger than on a clear MgO surface, thereby attracting more Ag atoms to cluster together, and forming atomic islands.展开更多
The adsorptions of a series of alkali metal （AM） atoms, Li, Na, K, Rb and Cs, on a Si（001）-2 × 2 surface at 0.25 monolayer coverage have been investigated systematically by means of density functional theory ...The adsorptions of a series of alkali metal （AM） atoms, Li, Na, K, Rb and Cs, on a Si（001）-2 × 2 surface at 0.25 monolayer coverage have been investigated systematically by means of density functional theory calculations. The effects of the size of AM atoms on the Si（001） surface are focused in the present work by examining the most stable adsorption site, diffusion path, band structure, charge transfer, and the change of work function for different adsorbates. Our results suggest that, when the interactions among AM atoms are neglectable, these AM atoms can be divided into three classes. For Li and Na atoms, they show unique site preferences, and correspond to the strongest and weakest AM-Si interactions, respectively. In particular, the band structure calculation indicates that the nature of Li-Si interaction differs significantly from others. For the adsorptions of other AM atoms with larger size （namely, K, Rb and Cs）, the similarities in the atomic and electronic structures are observed, implying that the atom size has little influence on the adsorption behavior for these large AM atoms on the Si（001） surface.展开更多
To reveal the relative contribution of the components, Fe, Mn oxides or organic materials（OMs） in the surficial sediments（SSs）, and the natural surface coating samples（NSCSs） to adsorbing atrazine（AT）, a selec...To reveal the relative contribution of the components, Fe, Mn oxides or organic materials（OMs） in the surficial sediments（SSs）, and the natural surface coating samples（NSCSs） to adsorbing atrazine（AT）, a selective chemical extraction technique was employed, to remove the different components, and the adsorption characteristics of AT on the SSs and the NSCSs were investigated. The observed adsorptions of AT on the original and extracted SSs and NSCSs were analyzed by nonlinear least squares fitting（NLSF） to estimate the relative contribution of the components. The results showed that the maximum adsorption of AT on the NSCSs was greater than that in the SSs, before and after extraction treatments, implying that the NSCSs were more dominant than the SSs for organic pollutant adsorption. It was also found that the Fe oxides, OMs, and residues in SSs（NSCSs） facilitated the adsorption of AT, but Mn oxides directly or indirectly restrained the interaction of AT with SSs（NSCSs） particles. The contribution of the Fe oxides to AT adsorption was more than that of OMs; the greatest contribution to AT adsorption on a molar basis was from the Fe oxides in the nonresidual fractions, indicating that the Fe oxides played an important role in controlling the environmental behavior of AT in an aquatic environment.展开更多
T shaped skin-stiffener joint are one of the most commonly used structures in aerospace components.It has been proven in various studies that these joints are susceptible to failure when loaded in pull out conditions ...T shaped skin-stiffener joint are one of the most commonly used structures in aerospace components.It has been proven in various studies that these joints are susceptible to failure when loaded in pull out conditions however,in specific applications these joints undergo pull loading.De-lamination/de-bond nucleation and its growth is one of the most common failure mechanisms in a fiber reinforced composite structure.Crack growth takes place due to the induced interlaminar normal and shear stresses between different structural constituents when a load is applied.In this study,Finite Element Analysis has been performed using cohesive contact interactions on a composite T-joint to simulate the pull out test conditions.A simplified shell based model coupled with CZM is proposed,which can evaluate the failure initiation and progression accurately with lesser computational efforts.The final failure occurred at a displacement of 4.71 mm at the computed failure load of 472.57 kgf for basic configuration.Computed Failure load for the padded configuration is 672.8 kgf and corresponding displacement is 4.6 mm.The results obtained by the proposed numerical model are validated by experimental results and it is observed that predicted failure displacements and failure load calculated were correlating reasonably well with the experiment.展开更多
The plane-wave pseudopotential function method, based on density-functional theory, has been used to calculate the adsorption, electronic band structures, orbitals and optical absorption spectrum of [Fe（CN）6]^4- on ...The plane-wave pseudopotential function method, based on density-functional theory, has been used to calculate the adsorption, electronic band structures, orbitals and optical absorption spectrum of [Fe（CN）6]^4- on TiOz anatase（101） surface. Our calculations reveal that the surface-modified anatase system has large adsorption energy and a much narrower band gap. [Fe（CN）6]^4- adsorption on the （101） surface could lead to a large red shift of the anatase optical absorption threshold, which extends into a visible region significantly. The calculated results are in agreement with the experiment and other theoretical studies reasonably. It is very important for the understanding and further development ofphotovoltaic materials that are active under visible light.展开更多
The surface organic modification of Fe3O4 nanoparticles with silane coupling reagent KH570 was studied. The modified and unmodified nanoparticles were characterized by FT-IR, XPS and TEM. The spectra of FT-IR and XPS ...The surface organic modification of Fe3O4 nanoparticles with silane coupling reagent KH570 was studied. The modified and unmodified nanoparticles were characterized by FT-IR, XPS and TEM. The spectra of FT-IR and XPS revealed that KH570 was coated onto the surface of Fe3O4 nanoparticles to get Fe-O- Si bond and an organic coating layer also was formed. Fe3O4 nanoparticles were spheres partly with mean size of 18,8 nm studied by TEM, which was consistent with the result 17.9 nm calculated by Scherrer＇s equation. KH570 was adsorbed on surface and formed chemistry bond to be steric hindrance repulsion which prevented nanoparticles from reuniting. Then glycol-based Fe3O4 magnetic liquids dispersed stably was gained.展开更多
Twenty kinds of adsorptions of HCN on the Fe（100）, Fe（111） and Fe（110） surfaces at the 1/4 monolayer coverage are found using the density functional theory. For Fe（100）, the adsorption energy of the most stabl...Twenty kinds of adsorptions of HCN on the Fe（100）, Fe（111） and Fe（110） surfaces at the 1/4 monolayer coverage are found using the density functional theory. For Fe（100）, the adsorption energy of the most stable configuration where the HCN locates at the fourfold site with the C-N bonded to four Fe atoms is 1.928 eV. The most favored adsorption structure for HCN on Fe（111） is f-η3（N）-h-η3（C）, in which the C-N bond is almost parallel to the surface, and the adsorption energy is 1.347 eV. On Fe（110）, the adsorption energy in the most stable configuration in which HCN locates at the two long-bridge sites is 1.777 eV. The adsorption energy of the parallel orientation for HCN is larger than that of the perpendicular configuration. The binding mechanism of HCN on the Fe（100）, Fe（111） and Fe（110） surfaces is also analyzed by Mulliken charge population and the density of states in HCN. The result indicates that the configurations in which the adsorbed HCN becomes the non-linear are beneficial to the formation of the addition reaction for hydrogen. The nature that the introduction of Fe into the catalyst could increase the catalytic activity of the bimetallic catalyst in the addition reaction of hydrogen for nitriles is revealed.展开更多
Response surface methodology(RSM)was employed to optimize the control parameters of TiO_(2)/graphene with exposed{001}facets during synthesis,and its enhanced photocatalytic activities were evaluated in the photodegra...Response surface methodology(RSM)was employed to optimize the control parameters of TiO_(2)/graphene with exposed{001}facets during synthesis,and its enhanced photocatalytic activities were evaluated in the photodegradation of toluene.Experimental results were in good agreement with the predicted results obtained using RSM with a correlation coefficient(R^(2))of 0.9345.When 22.06 mg of graphite oxide(GO)and 2.09 mL of hydrofluoric acid(HF)were added and a hydrothermal time of 28 h was used,a maximum efficiency in the degradation of toluene was achieved.X-ray diffraction(XRD),transmission electron microscopy(TEM),and scanning electron microscopy(SEM)were employed to characterize the obtained hybrid photocatalyst.The electron transferred between Ti and C retarded the combination of electron–hole pairs and hastened the transferring of electrons,which enhanced the photocatalytic activity.展开更多
This paper presents the results of a study concerned with the surface hardening of Fe-based alloys and WC-8Co cemented carbide by inte- grating laser cladding and the electrospark deposition processes. Specimens of lo...This paper presents the results of a study concerned with the surface hardening of Fe-based alloys and WC-8Co cemented carbide by inte- grating laser cladding and the electrospark deposition processes. Specimens of low carbon steel were processed firstly by laser cladding with Fe-based alloy powders and then by electrospark deposition with WC-SCo cemented carbide. It is shown that, for these two treatments, the electrospark coating possesses finer microstructure than the laser coating, and the thickness and surface hardness of the electrospark coating can be substantially increased.展开更多
A binary Fe-Al alloyed layer was synthesized on 45 steel by means of double glow plasma surface alloying technique. The corrosion-resisting layer prepared is composed of a sedimentary layer and a diffusion layer, with...A binary Fe-Al alloyed layer was synthesized on 45 steel by means of double glow plasma surface alloying technique. The corrosion-resisting layer prepared is composed of a sedimentary layer and a diffusion layer, with a total thickness of about 180 μm. The aluminum content of the alloyed layer shows gradual change from surface to the inside of substrate. The ideal profile is beneficial to the metallurgical bonding of the surface alloying layer with substrate materials. The microstructure of both layers consists of the Fe-Al intermetallic compound, which is FeAl with B2 structure in the sedimentary layer and Fe3Al with incompletely ordered DO3 structure in the diffusion layer. The protective film exhibits high micro-hardness. In comparison with the substrate of 45 steel, the corrosion resistance of the aluminized sample is much higher in 2.0% Na2S and 0.05 mol/L Na2SO4 + 0.5 mol/L NaCl mixed solutions.展开更多
FeO;supported on activated carbon(AC) has been shown to be an ideal catalyst for catalytic wet peroxide oxidation(CWPO) due to its high CWPO reaction activity and stability. Although there have been some studies on th...FeO;supported on activated carbon(AC) has been shown to be an ideal catalyst for catalytic wet peroxide oxidation(CWPO) due to its high CWPO reaction activity and stability. Although there have been some studies on the mechanism of Fe/AC catalysis in CWPO, the specific contribution of each component(surface oxygen groups and FeOxon AC) inside an Fe/AC catalyst and their corresponding reaction mechanism remain unclear, and the reaction stability of CWPO catalysts has rarely been discussed. Then the optimal CWPO catalyst in our laboratory, 3%Fe/AC, was selected.(1) By removing certain components on the AC through heat treatment, its contribution to the reaction and the corresponding reaction mechanism were investigated. With the aid of temperature-programmed desorption–mass spectrometry(TPD–MS) and the CWPO reaction, the normalized catalytic contributions of components were shown to be: 37.3%(carboxylic groups), 5.3%(anhydride), 19.3%(ether/hydroxyl),-71.4%(carbonyl groups) and 100%(FeOx),respectively. DFT calculation and EPR analysis confirmed that carboxylic groups and Fe_(2)O_(3) are able to activate the H_(2)O_(2) to generate·OH.(2) The catalysts at were characterized at different reaction times(0 h, 450 h, 900 h, 1350 h, and 1800 h) by TPD–MS and M?ssbauer spectroscopy. Results suggested that the number of carboxylic goups gradually increased and the size of paramagnetic Fe_(2)O_(3) particle crystallites gradually increased as the reactions progressed. The occurrence of strong interactions between metal oxides and AC was also confirmed. Due to these effects, the strong stability of 3%Fe/AC was further improved. Therefore, the reasons for the high activity and strong stability of 3%Fe/AC in CWPO were clearly shown. We believe that this work provides an idea of the removal of cresols from wastewater into the introduction to show the potential applications of CWPO.展开更多
Effect of ion nitriding modification on surface hardness, corrosion resistance and magnetostriction of （Tb0.3Dy0.7）Fe1.95 alloy was investigated. Results demonstrated that a 100-200 nm thick nitrided layer was forme...Effect of ion nitriding modification on surface hardness, corrosion resistance and magnetostriction of （Tb0.3Dy0.7）Fe1.95 alloy was investigated. Results demonstrated that a 100-200 nm thick nitrided layer was formed on the sample surface by ion nitriding treatment, which improved obviously surface hardness, wear, and corrosion resistance properties of （Tb0.3Dy0.7）Fe1.95 alloys. The surface hardness was increased from HV587 to HV622 after ion nitriding at 650 K for 6 h. Furthermore, ion nitriding treatment had almost no influence on mag- netostrictive performance as the nitrided layer was quite thin and the treatment temperature was not too high. The results might provide us a new approach for surface modification of （Tb0.3Dy0.7）Fe1.95 alloy.展开更多
The 5-parameter Morse pntential（5-MP） of the interaction between oxygen atoms and iron surfaces was constructed. The adsorption and diffusion of O atoms on Fe low-index and Fe（211 ） high-index surfaces were invest...The 5-parameter Morse pntential（5-MP） of the interaction between oxygen atoms and iron surfaces was constructed. The adsorption and diffusion of O atoms on Fe low-index and Fe（211 ） high-index surfaces were investigated by using 5-MP. All the critical characteristics of the system, such as adsorption site, adsorption geometry, binding energy, and eigenvalues for vibration, were calculated. The calculation results show that O atoms are located at the fourfold hollow site of the Fe（100） surface with an eigenvibration at437 cm^-1. These results are in good agreement with the experimental and theoretical results obtained previously. With regard to the adsorption site of O-Fe（110） system, the authors of this study assume that the preferential adsorption state is the H3 site and not the LB site, which is not in agreement with the experimental inferences obtained earlier. However, on the Fe（ 111 ） and Fe（211 ） surfaces, O atoms predominantly occupy the quasi-3-fold site.展开更多
基金supported by the National Natural Science Foundation of China(Nos.21773030,21371034,21503042 and 51574090)Natural Science Foundation Fund of Fujian Province(No.2017J01409)the Education Department of Fujian Province(No.JAT160655)
文摘The CO_2 adsorption on CaO(001) surface at different coverages from 1/9 monolayer(ML) to 1 ML has been investigated using density functional theory calculations. With the analysis of the most stable adsorption structures at different coverages, the mechanism of CaO(001)surface carbonating into CaCO_3 has been explored. At low coverages(≤1/3 ML), CO_2 molecule prefers sitting in parallel pattern on the CaO(001) surface, while the structure of the CaO(001)surface remains unchanged. At medium coverage(4/9 ～ 2/3 ML), the repulsive interactions between oxygen atoms of CO_2 become stronger, and the calcium carbonation structure appears on the CaO(001) surface. At high coverage( ≥ 7/9 ML), the structure of the CaO(001) surface is deeply damaged, and a few CO_2 molecules have penetrated into the surface and bound to the O atom of the second layer(sub-surface), eventually forming the layered structure of CaCO_3.Additionally, herein has discussed the simulation of HREELS and thermodynamical stability of these structures at different coverages.
文摘The Zn and Fe modified /ZrO<sub>2</sub>-Al<sub>2</sub>O<sub>3</sub> catalyst (Zn-Fe-SZA) was prepared and mechanisms of deactivation and methods for regeneration of as-prepared catalyst were explored with n-pentane isomerization as a probe reaction. The results indicated that the isopentane yield of the fresh Zn-Fe-SZA-F catalyst was about 57% at the beginning of the run, and declined gradually to 50% within 1500 min, then fell rapidly from 50% to 40% between 1500 and 2500 minutes. The deactivation of Zn-Fe-SZA catalyst may be caused by carbon formation on surface of the catalyst, sulfate group attenuation owing to reduction by hydrogen, removal of sulfur species and the loss of strong acid sites. It was found that the initial catalytic activity over Zn-Fe-SZA-T catalyst was 48%, which recovered by 84.3% as compared to that of fresh catalyst (57%). However, it showed a sharp decrease in isopentane yield from 48% to 29% within 1500 minutes, showing poor stability. This is associated to the loss of acidity caused by removal of sulfur species cannot be basically restored by thermal treatment. Resulfating the calcined catalyst could improve the acidity of catalyst significantly, especially strong acid sites, as compared with the calcined sample. The improved stability of the resulfated catalyst can be explained by: 1) eliminaton of carbon deposition to some extent by calcination process, 2) formation of improved acidic nature by re-sulfation, favoring isomerization on acidic sites, 3) restructuring of the acid and metal sites via the calcination-re-sulfation procedure.
基金Project supported by the Scientific Research Fund of Hunan Provincial Education Department, China (Grant No. 09B021)
文摘The interaction of Ag atoms with a defective MgO（001） surface is systematically studied based on density functional theory. The Ag clusters are deposited on neutral and charged oxygen vacancies of the MgO（001） surface. The structures of Ag clusters take the shape of simple models of two- or three-dimensional （2D and 3D） metal particles deposited on the MgO surface. When the nucleation of the metal clusters occurs in the Fs （missing neutral O） centre, the interaction with the substrate is considerably stronger than that in the Fs^＋ （missing O-） centre. The results show that the adsorption of Ag atoms on the MgO surface with oxygcn vacancy is stronger than on a clear MgO surface, thereby attracting more Ag atoms to cluster together, and forming atomic islands.
基金supported by the National Natural Science Foundation of China(21203027)Fuzhou University(2012-XQ-11)
文摘The adsorptions of a series of alkali metal （AM） atoms, Li, Na, K, Rb and Cs, on a Si（001）-2 × 2 surface at 0.25 monolayer coverage have been investigated systematically by means of density functional theory calculations. The effects of the size of AM atoms on the Si（001） surface are focused in the present work by examining the most stable adsorption site, diffusion path, band structure, charge transfer, and the change of work function for different adsorbates. Our results suggest that, when the interactions among AM atoms are neglectable, these AM atoms can be divided into three classes. For Li and Na atoms, they show unique site preferences, and correspond to the strongest and weakest AM-Si interactions, respectively. In particular, the band structure calculation indicates that the nature of Li-Si interaction differs significantly from others. For the adsorptions of other AM atoms with larger size （namely, K, Rb and Cs）, the similarities in the atomic and electronic structures are observed, implying that the atom size has little influence on the adsorption behavior for these large AM atoms on the Si（001） surface.
基金Supported by the National Natural Science Foundation of China(No.50879025)the Scientific Start-up Fund from North China Electric Power University, China(No.X60218)the National Basic Research Program of China(No.2004CB3418501).
文摘To reveal the relative contribution of the components, Fe, Mn oxides or organic materials（OMs） in the surficial sediments（SSs）, and the natural surface coating samples（NSCSs） to adsorbing atrazine（AT）, a selective chemical extraction technique was employed, to remove the different components, and the adsorption characteristics of AT on the SSs and the NSCSs were investigated. The observed adsorptions of AT on the original and extracted SSs and NSCSs were analyzed by nonlinear least squares fitting（NLSF） to estimate the relative contribution of the components. The results showed that the maximum adsorption of AT on the NSCSs was greater than that in the SSs, before and after extraction treatments, implying that the NSCSs were more dominant than the SSs for organic pollutant adsorption. It was also found that the Fe oxides, OMs, and residues in SSs（NSCSs） facilitated the adsorption of AT, but Mn oxides directly or indirectly restrained the interaction of AT with SSs（NSCSs） particles. The contribution of the Fe oxides to AT adsorption was more than that of OMs; the greatest contribution to AT adsorption on a molar basis was from the Fe oxides in the nonresidual fractions, indicating that the Fe oxides played an important role in controlling the environmental behavior of AT in an aquatic environment.
文摘T shaped skin-stiffener joint are one of the most commonly used structures in aerospace components.It has been proven in various studies that these joints are susceptible to failure when loaded in pull out conditions however,in specific applications these joints undergo pull loading.De-lamination/de-bond nucleation and its growth is one of the most common failure mechanisms in a fiber reinforced composite structure.Crack growth takes place due to the induced interlaminar normal and shear stresses between different structural constituents when a load is applied.In this study,Finite Element Analysis has been performed using cohesive contact interactions on a composite T-joint to simulate the pull out test conditions.A simplified shell based model coupled with CZM is proposed,which can evaluate the failure initiation and progression accurately with lesser computational efforts.The final failure occurred at a displacement of 4.71 mm at the computed failure load of 472.57 kgf for basic configuration.Computed Failure load for the padded configuration is 672.8 kgf and corresponding displacement is 4.6 mm.The results obtained by the proposed numerical model are validated by experimental results and it is observed that predicted failure displacements and failure load calculated were correlating reasonably well with the experiment.
基金the Scientific and Technology Foundation of Fuzhou University and the Key Project of Fujian Province (2005HZ01-2-6)
文摘The plane-wave pseudopotential function method, based on density-functional theory, has been used to calculate the adsorption, electronic band structures, orbitals and optical absorption spectrum of [Fe（CN）6]^4- on TiOz anatase（101） surface. Our calculations reveal that the surface-modified anatase system has large adsorption energy and a much narrower band gap. [Fe（CN）6]^4- adsorption on the （101） surface could lead to a large red shift of the anatase optical absorption threshold, which extends into a visible region significantly. The calculated results are in agreement with the experiment and other theoretical studies reasonably. It is very important for the understanding and further development ofphotovoltaic materials that are active under visible light.
基金the Natural Science Fund of Jiangsu province (No.BK2007586)Jiangsu Planned Projects(No.0701012B)for Postdoctoral Research Funds
文摘The surface organic modification of Fe3O4 nanoparticles with silane coupling reagent KH570 was studied. The modified and unmodified nanoparticles were characterized by FT-IR, XPS and TEM. The spectra of FT-IR and XPS revealed that KH570 was coated onto the surface of Fe3O4 nanoparticles to get Fe-O- Si bond and an organic coating layer also was formed. Fe3O4 nanoparticles were spheres partly with mean size of 18,8 nm studied by TEM, which was consistent with the result 17.9 nm calculated by Scherrer＇s equation. KH570 was adsorbed on surface and formed chemistry bond to be steric hindrance repulsion which prevented nanoparticles from reuniting. Then glycol-based Fe3O4 magnetic liquids dispersed stably was gained.
文摘Twenty kinds of adsorptions of HCN on the Fe（100）, Fe（111） and Fe（110） surfaces at the 1/4 monolayer coverage are found using the density functional theory. For Fe（100）, the adsorption energy of the most stable configuration where the HCN locates at the fourfold site with the C-N bonded to four Fe atoms is 1.928 eV. The most favored adsorption structure for HCN on Fe（111） is f-η3（N）-h-η3（C）, in which the C-N bond is almost parallel to the surface, and the adsorption energy is 1.347 eV. On Fe（110）, the adsorption energy in the most stable configuration in which HCN locates at the two long-bridge sites is 1.777 eV. The adsorption energy of the parallel orientation for HCN is larger than that of the perpendicular configuration. The binding mechanism of HCN on the Fe（100）, Fe（111） and Fe（110） surfaces is also analyzed by Mulliken charge population and the density of states in HCN. The result indicates that the configurations in which the adsorbed HCN becomes the non-linear are beneficial to the formation of the addition reaction for hydrogen. The nature that the introduction of Fe into the catalyst could increase the catalytic activity of the bimetallic catalyst in the addition reaction of hydrogen for nitriles is revealed.
基金supported by the National Natural Science Foundation of China(Nos.21406164,21466035 and 51203111)the National Basic Research Program of China("973"Program,Nos.2012CB720100 and 2014CB239300)
文摘Response surface methodology(RSM)was employed to optimize the control parameters of TiO_(2)/graphene with exposed{001}facets during synthesis,and its enhanced photocatalytic activities were evaluated in the photodegradation of toluene.Experimental results were in good agreement with the predicted results obtained using RSM with a correlation coefficient(R^(2))of 0.9345.When 22.06 mg of graphite oxide(GO)and 2.09 mL of hydrofluoric acid(HF)were added and a hydrothermal time of 28 h was used,a maximum efficiency in the degradation of toluene was achieved.X-ray diffraction(XRD),transmission electron microscopy(TEM),and scanning electron microscopy(SEM)were employed to characterize the obtained hybrid photocatalyst.The electron transferred between Ti and C retarded the combination of electron–hole pairs and hastened the transferring of electrons,which enhanced the photocatalytic activity.
文摘This paper presents the results of a study concerned with the surface hardening of Fe-based alloys and WC-8Co cemented carbide by inte- grating laser cladding and the electrospark deposition processes. Specimens of low carbon steel were processed firstly by laser cladding with Fe-based alloy powders and then by electrospark deposition with WC-SCo cemented carbide. It is shown that, for these two treatments, the electrospark coating possesses finer microstructure than the laser coating, and the thickness and surface hardness of the electrospark coating can be substantially increased.
基金Project(BK2005128) supported by the Natural Science Foundation of Jiangsu Province, China
文摘A binary Fe-Al alloyed layer was synthesized on 45 steel by means of double glow plasma surface alloying technique. The corrosion-resisting layer prepared is composed of a sedimentary layer and a diffusion layer, with a total thickness of about 180 μm. The aluminum content of the alloyed layer shows gradual change from surface to the inside of substrate. The ideal profile is beneficial to the metallurgical bonding of the surface alloying layer with substrate materials. The microstructure of both layers consists of the Fe-Al intermetallic compound, which is FeAl with B2 structure in the sedimentary layer and Fe3Al with incompletely ordered DO3 structure in the diffusion layer. The protective film exhibits high micro-hardness. In comparison with the substrate of 45 steel, the corrosion resistance of the aluminized sample is much higher in 2.0% Na2S and 0.05 mol/L Na2SO4 + 0.5 mol/L NaCl mixed solutions.
基金funded by the National Natural Science Foundation of China (52100072)the Beijing Natural Science Foundation(8214056)+2 种基金the special fund of Beijing Key Laboratory of Clean Fuels and Efficient Catalytic Emission Reduction Technology,the Strategic Priority Research Program of the Chinese Academy of Sciences(XDA21021101)the National Key Research and Development Program of China (2019YFA0705803)Scientific Research Common Program of Beijing Municipal Commission of Education(KM202010017006)。
文摘FeO;supported on activated carbon(AC) has been shown to be an ideal catalyst for catalytic wet peroxide oxidation(CWPO) due to its high CWPO reaction activity and stability. Although there have been some studies on the mechanism of Fe/AC catalysis in CWPO, the specific contribution of each component(surface oxygen groups and FeOxon AC) inside an Fe/AC catalyst and their corresponding reaction mechanism remain unclear, and the reaction stability of CWPO catalysts has rarely been discussed. Then the optimal CWPO catalyst in our laboratory, 3%Fe/AC, was selected.(1) By removing certain components on the AC through heat treatment, its contribution to the reaction and the corresponding reaction mechanism were investigated. With the aid of temperature-programmed desorption–mass spectrometry(TPD–MS) and the CWPO reaction, the normalized catalytic contributions of components were shown to be: 37.3%(carboxylic groups), 5.3%(anhydride), 19.3%(ether/hydroxyl),-71.4%(carbonyl groups) and 100%(FeOx),respectively. DFT calculation and EPR analysis confirmed that carboxylic groups and Fe_(2)O_(3) are able to activate the H_(2)O_(2) to generate·OH.(2) The catalysts at were characterized at different reaction times(0 h, 450 h, 900 h, 1350 h, and 1800 h) by TPD–MS and M?ssbauer spectroscopy. Results suggested that the number of carboxylic goups gradually increased and the size of paramagnetic Fe_(2)O_(3) particle crystallites gradually increased as the reactions progressed. The occurrence of strong interactions between metal oxides and AC was also confirmed. Due to these effects, the strong stability of 3%Fe/AC was further improved. Therefore, the reasons for the high activity and strong stability of 3%Fe/AC in CWPO were clearly shown. We believe that this work provides an idea of the removal of cresols from wastewater into the introduction to show the potential applications of CWPO.
基金supported by National High-Tech R&D Program (2006AA03Z106)Beijing Natural Science Foundation (2062012)National Natural Science Foundation (50801006)
文摘Effect of ion nitriding modification on surface hardness, corrosion resistance and magnetostriction of （Tb0.3Dy0.7）Fe1.95 alloy was investigated. Results demonstrated that a 100-200 nm thick nitrided layer was formed on the sample surface by ion nitriding treatment, which improved obviously surface hardness, wear, and corrosion resistance properties of （Tb0.3Dy0.7）Fe1.95 alloys. The surface hardness was increased from HV587 to HV622 after ion nitriding at 650 K for 6 h. Furthermore, ion nitriding treatment had almost no influence on mag- netostrictive performance as the nitrided layer was quite thin and the treatment temperature was not too high. The results might provide us a new approach for surface modification of （Tb0.3Dy0.7）Fe1.95 alloy.
基金the Natural Science Foundation of Shandong Province(No Y2002B09)
文摘The 5-parameter Morse pntential（5-MP） of the interaction between oxygen atoms and iron surfaces was constructed. The adsorption and diffusion of O atoms on Fe low-index and Fe（211 ） high-index surfaces were investigated by using 5-MP. All the critical characteristics of the system, such as adsorption site, adsorption geometry, binding energy, and eigenvalues for vibration, were calculated. The calculation results show that O atoms are located at the fourfold hollow site of the Fe（100） surface with an eigenvibration at437 cm^-1. These results are in good agreement with the experimental and theoretical results obtained previously. With regard to the adsorption site of O-Fe（110） system, the authors of this study assume that the preferential adsorption state is the H3 site and not the LB site, which is not in agreement with the experimental inferences obtained earlier. However, on the Fe（ 111 ） and Fe（211 ） surfaces, O atoms predominantly occupy the quasi-3-fold site.
