Evolution of the Design of Cold Mass Support for the ITER Magnet Feeder System

This paper presents the evolution of the design of cold mass support for the ITER magnet feeder system. The glass fibers in the cylinder and the flanges of the normal G10 support are discontinuous in the preliminary design. The heat load of this support from the analysis is only 4.86 W. However, the mechanical test of the prototype showed that it can only endure 9 kN lateral force, which is significantly less than the required 20 kN. So, the configuration of the glass fibers in the cylinders and flanges of this G10 support are modified by changing it to a continuous and knitted type to reinforce the support, and then a new improved prototype is manufactured and tested. It could endure 15＇kN lateral forces this time, but still not meet the required 20 kN. Finally, the SS316LN material is chosen for the cold mass supports. The analysis results show that it is safe under 20 kN lateral forces with the heat load increased to 14.8 W. Considering the practical application, the requirements of strength is of primary importance. So, this SS316LN cold mass support is acceptable for the ITER magnet feeder system. On the other hand, the design idea of using continuous and knitted glass fibers to reinforce the strength of a G10 support is a good reference for the case with a lower heat load and not too high Lorentz force.

Dynamic Analysis for the Global Performance of An SPM-Feeder-Cage System Under Waves and Currents

In the present study, the dynamic response of a coupled SPM-feeder-cage system under irregular waves and shear currents is analyzed. A numerical model is developed by using the commercial software Orca Flex. Hydrodynamics coefficients of the vessel are calculated by using a 3D diffraction/radiation panel program. First- and second-order wave forces are included in the calculations. Morison equation is used to compute the drag force on line elements representing the net. Drag coefficients are determined at every time step in the simulation considering the relative normal velocity between the structural elements and the fluid flow. The dynamic response of the coupled system is analyzed for various environments and net materials. The results of the study show the effects of solidity ratio of the net and vertical positions of the cage on the overall dynamic response of the system, confirming the viability of this type of configuration for future development of offshore aquaculture in deep waters.

Research on communication system of underground safety management based on leaky feeder cable

According to the current working status of underground safety management and production scheduling, the importance and existed problem of underground mine radio communication were summarized, and the basic principle and classification of leaky feeder cable were introduced and the characteristics of cable were analyzed specifically in depth, and the application model of radio communication system for underground mine safety management was put forward. Meanwhile, the research explanation of the system component, function and evaluation was provided. The discussion result indicates that communication system of underground mine safety management which is integrated two-way relay amplifier and other equipment has many communication functions, and underground mine mobile communication can be achieved well.

Optimisation of Electrical Distribution System by Using Solar Thermal Powered Systems and Its Impact on Electrical Distribution Feeders

In this research, the performance of the solar thermal powered systems (STPS) is analyzed with different models (without inserts, with inserts and with Nano fluids with different concentrations) and its impact on the Electric load in a residential/Institutional Electrical Distribution system. For this purpose, the electrical and solar thermal water heater is tested and validated. Solar thermal powered systems and its impact on the Institutional electrical distribution feeders are tested and compared with the energy efficiency (EE) and cost optimization. The goal of this paper is to analyze the impact of solar thermal energy on electrical energy consumption in the electrical distribution feeder level. The electrical system cost and energy consumptions are tabulated and observed that there is a considerable savings.

Design of Weigh Feeder Control System for Energy Saving Using Performance-Adaptive Method

This paper discusses a design method for the control system of a weigh feeder that supplies powder and granular material at a constant rate. Most weigh feeders employed in industry are controlled by proportional and integral （PI） compensation, and the control performance is decided by the selection of parameters. To attain advanced control performance by PI control, the PI parameters are designed on the basis of generalized minimum variance control （GMVC）. In this study, to achieve user-specified control performance by GMVC-based PI control, the design parameters of GMVC are automatically adjusted using a performance-adaptive method. The control performance discussed in this study consists of the variance of the control error and that of the difference in the control input. In a conventional performance-adaptive method, the variance of the control error is reduced. In this study, to reduce energy consumption and to achieve user-specified control performance, the variance of the difference in the control input is specified and the design parameter is determined. To demonstrate its effectiveness, the proposed method is applied to an actual weigh feeder.

Substation Supervisory System Basedon Feeder Control Units

This paper introduces a kind of Feeder Control Units (FCUs) which treat feeders or main transformers as its objects. Being carefully designed, the FCU can separately meet the requirements such as signals’ acquisition, local control, on-time switchgear interlocking, etc. Equipped with a sort of high-speed serial communicahon interface, the FCUs can be distributively arranged near or into the switchgear, therefore a kind of distributed substation supervisory system can be formed.

Hi-Z fault location identification on low voltage distribution systems using IoT-based digital twin model computation

Distribution feeders carry and supply power to industrial,commercial and residential loads from the point where sub-transmission(33 kV level)ends after stepping down to suitable voltages,such as 11 kV and further down to 400/230 V.In recent times,high impedance(Hi-Z)faults on distribution systems are creating unique challenges to utilities both from operational and safety perspectives.Most of these Hi-Z faults occur at dis-tribution voltages of 15 kV or below,with the problem being worse at lower voltages.Hi-Z fault detection technologies emerged and were developed and incorporated on embedded platforms,such as relays,reclosers and sensors,which protect and monitor distribution systems.Although these technologies can detect Hi-Z fault on feeders,most of them cannot identify the exact location of the fault.Specifically,there is no solution available in literature for detecting Hi-Z fault location on low voltage(LV)circuits like 3-phase 4-wire 400 V distribution network.In this paper,we introduce a novel and a unique algorithm to identify the location of Hi-Z faults using proposed smart metres IoT data-based distribution system load flow and digital twin model representation of the network.Furthermore,a case study on the standard 33 bus LV system clearly depicts the func-tionality of the proposed algorithm.

Comparative Analysis of Five Different Homologous Feeder Cell Lines in the Ability to Support Rhesus Embryonic Stem Cells

In our previous study, five homologous feeder cell lines, Monkey ear skin fibroblasts （MESFs）, clonally derived fibroblasts from the MESFs （CMESFs）, monkey oviductal fibroblasts （MOFs）, monkey follicular granulosa fibroblast-like （MFGs） cells, monkey follicular granulosa epithelium-like （MFGEs） cells, were developed for the maintenance of rhesus embryonic stem cells （rESCs）. We found that MESFs, CMESFs, MOFs and MFGs, but not MFGEs, support the growth of rhesus embryonic stem cells. Moreover, we detected some genes that are upregulated in supportive feeder cell lines by semi-quantitative PCR. In the present study, we applied the GeneChip Rhesus Macaque Genome Array of Affymetrix Corporation to study the expression profiles of these five feeder cell lines, in purpose to find out which cytokines and signaling pathways were important in maintaining the rESCs, mRNAs of eight genes, including GREM2, bFGF, KITLG, DKK3, GREM1, AREG, SERPINF1 and LTBP1, were found to be upregulated in supportive feeder cell lines, but not in MFGE. The results indicate that many signaling pathways may play redundant roles in supporting the undifferentiated growth and maintenance of pluripotency in rESCs.

Effects of feeder layer and BRL conditioned medium on mouse embryonic stem cells

In vitro growth and maintenance of embryonic stem (ES) cell lines derived from ICM cells of various blastocysts of 129 strain mice, the sustenance of their pluripotency and normal karyotype depend on the feeder layer of mouse embryonic fibroblasts (MEF). Compared with the feeder layer of MEF cells, medium conditioned by Buffalo rat liver cells (BRL-CM) is able to maintain pluripotency and karyo-typic normality of ES cells only in short term cell propagation. Besides, ES cells grown in BRL-CM are also capable of aggregation with 8-cell embryos of Swiss strain and develop into germ line chimaeras. Modification to the method of aggregating ES cells with early embryos by making a hole in agar layer on the top of MEF feeder cells was shown to be more convenient and efficient than the conventional microdrop method.

Relationship between alumina mixing characteristics and feeder configurations in aluminum reduction cells

Because of the increasingly prominent problem of alumina content inhomogeneity in large or super-scale aluminum reduction cells,a transient numerical model for the alumina mixing process was developed for a400kA cell,and the relationship between the alumina content distribution and electrolyte flow field was analyzed.In the ANSYS software platform,several numerical simulation cases were presented to display the influence of the feeder configuration on the alumina mixing characteristics.The results showed that a large vortex flow of the molten electrolyte is beneficial for alumina mixing and uniform distribution in the inner areas of the vortexes.The alumina particles reach the inter-electrode zone in10?15s from the beginning of the feeding action,and the risk of early precipitation occurs in10?25s after the feeding.It was also found that a suitable grouping of feeders could reduce the content fluctuation and gradient.Therefore,a feeding on demand strategy was proposed,and the simulation results showed that although the spatial characteristics are not changed,the uniformity of the alumina content was markedly improved.

Operation and Force Analysis of the Guide Wire in a Minimally Invasive Vascular Interventional Surgery Robot System

To develop a robot system for minimally invasive surgery is significant,however the existing minimally invasive surgery robots are not applicable in practical operations,due to their limited functioning and weaker perception.A novel wire feeder is proposed for minimally invasive vascular interventional surgery.It is used for assisting surgeons in delivering a guide wire,balloon and stenting into a specific lesion location.By contrasting those existing wire feeders,the motion methods for delivering and rotating the guide wire in blood vessel are described,and their mechanical realization is presented.A new resistant force detecting method is given in details.The change of the resistance force can help the operator feel the block or embolism existing in front of the guide wire.The driving torque for rotating the guide wire is developed at different positions.Using the CT reconstruction image and extracted vessel paths,the path equation of the blood vessel is obtained.Combining the shapes of the guide wire outside the blood vessel,the whole bending equation of the guide wire is obtained.That is a risk criterion in the delivering process.This process can make operations safer and man-machine interaction more reliable.A novel surgery robot for feeding guide wire is designed,and a risk criterion for the system is given.

Mechanical Analysis and Optimization of ITER Upper ELM Coil & Feeder

International thermonuclear experimental reactor （ITER） edge localized mode （ELM） coils are used to mitigate or suppress ELMs. The location of the coils in the vacuum vessel and behind the blankets exposes them to high radiation levels and high temperatures. The feeders provide the power and cooling water for ELM coils. They are located in the chinmey ports and experience lower radiation and temperature levels. These coils and feeders work in a high magnetic field environment and are subjected to alternating electromagnetic force due to the interaction between high magnetic field and alternating current （AC） current in the coils. They are also subjected to thermal stresses due to thermal expansion. Using the ITER upper ELM coil and feeder as an example, mechanical analyses are performed to verify and optimize the updated design to enhance their structural performance. The results show that the conductor, jacket and bracket can meet the static, fatigue and crack threshold criteria. The optimization indicates that adding chamfers to the bracket can reduce the high stress of the bracket, and removing two rails can reduce the peak reaction force on the two rails arising from thermal expansion.

Underwater robot local dry welding system

To satisfy the demand for good quality underwater welding and maintenance of nuclear power stations,a set of local dry automatic welding systems has been developed.These systems were based on an underwater robot that consisted of a special high-power underwater welding power supply,diving wire feeder,mini drain cap,welding robot,and special underwater welding torch.With a digital signal controller microprocessor as its core and combined with a dual inverter topology,the welding power supply was characterized by full-digital construction and multi-waveform flexible output.A compact diving wire feeding device was designed,based on the armature voltage negative feedback and high-frequency chopping pulse width modulation.This device yielded a high-efficiency seal of the driving motor with the help of dynamic and static sealing technology.To overcome the difficulty of local protection and deslagging in the welding area,a mini drain cap(with a duplexgas structure)based on the principle of the convergent nozzle was designed.The practical tests and the underwater welding experiments revealed that the underwater robotic local dry welding system is quite feasible.That is,the system could strike the arc stably and reliably in the shallow water environment,and formed beautiful welding seams.

Probabilistic Fuzzy Approach to Assess RDS Vulnerability and Plan Corrective Action Using Feeder Reconfiguration

Two common problems for a typical Power distribution system are voltage collapse & instability. Challenge is to identify the vulnerable nodes and apply the effective corrective actions. This paper presents a probabilistic fuzzy approach to assess the node status and proposes feeder reconfiguration as a method to address the same. Feeder reconfiguration is altering the topological structures of distribution feeders by changing the open/closed states of the sectionalizing and ties switches. The solution is converge using a probabilistic fuzzy modeled solution, which defines the nodal vulnerability index (VI) as a function of node voltage and node voltage stability index and predicts nodes critical to voltage collapse. The information is further used to plan best combination of feeders from each loop in distribution system to be switched out such that the resulting configuration gives the optimal performance i.e. best voltage profile and minimal kW losses. The proposed method is tested on established radial distribution system and results are presented.

Why Fast Trains Work: An Assessment of a Fast Regional Rail System in Perth, Australia

Perth’s new 72 km long Southern Rail System opened in 2007. With a maximum speed of 137 km/hr and an average speed of almost 90 km/hr this system acts more like a new high speed rail than a suburban rail system, which in Australia typically averages around 40 km/hr for an all-stops services. The Southern Rail Line was very controversial when being planned as the urban areas served are not at all typical of those normally provided with rail but instead were highly car dependent and scattered low density land uses. Nevertheless it has been remarkably successful, carrying over 70,000 people per day (five times the patronage on the express buses it replaced) and has reached the patronage levels predicted for 2021 a decade ahead of time. The reasons for this success are analyzed and include well-designed interchanges, careful integration of bus services, the use of integrated ticketing and fares without transfer penalties and, crucially the high speed of the system when compared to competing car based trips. The Southern Rail Line in effect explodes the current paradigm of transfer penalties, exposing this as a myth. The lessons for transport planning in low density cities are significant, and are explored further in the paper.

Comparative analysis of different feeder layers with 3T3 fibroblasts for culturing rabbits limbal stem cells

AIM： To explore the possibility of human umbilical cord mesenchymal stem cells（h UCMSCs）, human umbilical vein endothelial cells（h UVECs）, human dental pulp stem cells（h DPSCs） and human periodontal ligament stem cells（h PDLSCs） serving as feeder cells in co-culture systems for the cultivation of limbal stem cells.METHODS： Different feeder layers were cultured in Dulbecco＇s modified Eagle＇s medium（DMEM）/F12 and were treated with mitomycin C. Rabbits limbal stem cells（LSCs） were co-cultured on h UCMSCs, h UVECs, h DPSCs, h PDLSCs and NIH-3T3, and then comparative analysis were made between each group to see their respective colony-forming efficiency（CFE） assay and immunofluorescence（IPO13,CK3/12）.RESULTS： The efficiency of the four type cells in supporting the LSCs morphology and its cellular differentiation was similar to that of NIH-3T3 fibroblasts as demonstrated by the immunostaining properties analysis, with each group exhibiting a similar strong expression pattern of IPO13, but lacking CK3 and CK12 expression in terms of immunostaining. But h UCMSCs, h DPSCs and h PDLSCs feeder layers were superior in promoting colony formation potential of cells when compared to h UVECs and feedercell-free culture.CONCLUSION： hUCMSCs, hDPSCs and hPDLSCs can be a suitable alternative to conventional mouse NIH-3T3 feeder cells, so that risk of zoonotic infection can be diminished.

Dynamic Power Transmission Using Common RF Feeder with Dual Supply

This paper proposes the design concept of a dynamic charging system for electric vehicles using multiple transmitter coils connected to a common radio frequency(RF)feeder driven by a pair of two power supplies.Using a common RF feeder for multiple transmitter coils reduces the power electronic redundancy compared to a conventional system,where each transmitter coil is individually driven by one switched-mode power supply.Currently,wireless charging of electric vehicles is recommended to operate in the frequency range of 85 kHz and beyond.In this frequency range,the signal wavelength is shorter than about 3.5 km.Therefore,a charging pad longer than several hundred meters is subject to the standing wave effect.In such a case,the voltage significantly varies along the RF feeder,resulting in a variation in the received power level when the receiver moves.Specifically,the received power significantly deteriorates when the receiver is nearby a node of the voltage standing wave.In this paper,we employ a pair of two power sources which are electrically separated by an odd-integer number of the quarter wavelength to drive the RF feeder.As a result,the voltage standing wave generated by one power source is complemented by that of the other,leading to stable received power and transmission efficiency at all the receiver’s positions along with the charging pad.Simulation results at the 85 kHz frequency band verify the output power stabilization effect of the proposed design.It is worth noting that the proposed concept can also be applied to simultaneous wireless information and power transfer(SWIPT)for passive radio frequency identification(RFID)tags by raising the operation frequency to higher industrial,scientific and medical(ISM)bands,e.g.,13.56 MHz and employing similar modulation methods as in the current RFID technology.

Gas-Solid Flow Behavior in a Pneumatic Conveying System for Drying Applications: Coarse Particles Feeding with a Venturi Device

The feeding of coarse particles (>0.5 mm diameter) directly into a riser operating at positive pressure is important for drying and pre-heating applications. The presence of the feeding device can lead to heterogeneity of drying and heating, and is the main factor responsible for pressure loss in short conveying systems. However, there is a lack of information concerning the axial and radial distributions of coarse particles in this type of configuration, despite the recent advances when dealing with fine particles (FCC catalyst). The present work therefore investigates a vertical venturi feeder with the conveying system operating in dilute-phase regime with 1 mm spherical glass particles. Experimental assays revealed the behavior of the mass flow rate of solids in the system, and pressure measurements were made along the riser in order to evaluate the accuracy of simulations. Euler-Euler simulations provided close estimation of the experimental pressure drop and the pressure drop according to distance in the linear region. Simulation of the fluid dynamics in the riser showed that solids clusters were formed at low concentrations near the feeding device, reflecting heterogeneity in the solid phase volume fraction.

The Automated System of Unified Templates as an Element of Trainability of Microprocessor Relay Protection Devices

The article discusses the possibility of further modernization of the standard microprocessor relay protection of AC overhead system feeders DPA-27.5-TNF, which is operated on the Trans-Baikal Railway by creating an additional automated system of unified templates necessary for the occurrence of “trainability” elements. The templates will be formed via a separate dedicated channel for transmission, processing and storage of the necessary information, not related to the operation of the terminal, with its subsequent visualization at the workplace of the duty personnel of traction substations, together with information from the “GID” software received via another dedicated wired channel. With the help of such a base of unified preset templates, in the future, it will be possible not only to identify the specific causes of each emergency shutdown but also to reduce their number by dynamically adjusting the existing presets of the standard operation algorithm.

Finite Element Analysis and Structural Optimization of a Vibration Feeder Based on ANSYS

Based on ANSYS software, a finite element model is built for the fatigue break of a vibration feeder influenced by an exciting force alternate load. We first study the harmonic response of the feeder and discovers the weak links which is an angle steel junction of side plate, feed inlet and the junction panel between the no-feed side plate and the bottom plate. Then, we carry out structural optimization. A streamlined method for optimum design of a vibration feeder is presented.