The growing interest in additive manufacturing of GH4169 alloy was accompanied by the demand on spherical GH4169 powders with high performance.The powder particles were treated by radio frequency plasma with the diffe...The growing interest in additive manufacturing of GH4169 alloy was accompanied by the demand on spherical GH4169 powders with high performance.The powder particles were treated by radio frequency plasma with the different feeding rates.The microstructure and morphology,the particle size distribution of as-treated powders were studied by scanning electron microscopy and laser particle size analysis.It was demonstrated that GH4169 powders with extremely fine followability were obtained by radio frequency plasma spheroidization technology.With the same plasma parameters,the spheroidization efficiency of the particles varied with the feeding rates.When the rate of the powder feeding rates was too small,the excessive absorption of the heating by the powders caused vaporization,then the collection decreased.When the feeding rates was too large,the powder particles were insufficiently absorbed,resulting in defects in the powders.The microstructure of the as-treated spherical particles was mainly cell crystals,columnar crystals,and even microcrystals.Under the suitable plasma parameters,the resulting powders haved a slightly increased average particle size,excellent spheroidization,surface smoothness,followability,and bulk ratio.展开更多
Determining the suitable fish farming conditions for optimal growth is necessary for aquaculture production, but it is not very obvious because it requires a good understanding of species biology. Thus, this study aim...Determining the suitable fish farming conditions for optimal growth is necessary for aquaculture production, but it is not very obvious because it requires a good understanding of species biology. Thus, this study aims to evaluate the effects of different temperature regimes, stocking densities, and feeding rates on the growth of Nile tilapia, Oreochromis niloticus fingerlings that have been sex-reversed with 17α methyl testosterone. Three independent experiments were performed (with replicates) at the IRD Bel-Air fish farm (Dakar, Senegal) on 27-day-old fry maintained in six 25 L tanks with a batch of 100 individuals each. These fry were subjected to three different temperatures (26˚C, 28˚C, 30˚C;kept constant with thermostats), stocking densities (5, 10 and 15 ind/l) and feeding rates (5%, 10% and 15% of biomass;distributed three times a day). For the temperature and density treatments, fry was fed a pelleted feed containing 38% protein, distributed by hand at 10% of their total biomass, readjusted after each measurement. Growth performance (total weight, weight gain and daily weight gain), physicochemical parameters (temperature, oxygen, nitrite and phosphorus), feed conversion ratio (FCR) and survival rate (SR) were regularly monitored (weekly) during the experimental period. For the heat treatment, the results did not show an apparent relationship between growth performance and nitrite, phosphorus or dissolved oxygen (DO) contents. In contrast, there was a significant correlation between temperature and growth rates, with the best growth being obtained at 30˚C compared to 28˚C and 26˚C. Similarly, growth rates were correlated with stocking density and feeding rate but not with oxygen, temperature, nitrite or phosphorus levels. The best growth rates were observed at the lowest density (5 ind/l) and for the highest feeding rate (15% of biomass), which coincides with the best FCR and survival rates. Thus, 30˚C, 5 ind/l and 15% of biomass appeared to be the most favorable temperature, stocking density and feeding rate for optimal growth of Nile tilapia fry after inversion. The application of these results in the culture systems will allow to reach a good production of O. niloticus and thus to contribute to sustainable development of fish culture in Senegal.展开更多
To improve the declining performance of a full-feed peanut picking device or solve the mechanical failures that occur due to fluctuations in the feeding rate during operation,the 4HLJI-3000 peanut intelligent picking ...To improve the declining performance of a full-feed peanut picking device or solve the mechanical failures that occur due to fluctuations in the feeding rate during operation,the 4HLJI-3000 peanut intelligent picking combine harvester,which is a picking device with a self-adaptive adjustment of the working clearance,was developed as the research object in this study.Moreover,the key components,such as the picking roller,concave plate sieve and clearance adjustment mechanism of the concave plate sieve,were designed and analysed.Through the force analysis of the concave plate sieve of the picking device,the mathematical model of the concave plate sieve displacement of the picking device and feeding rate was obtained.The software system for monitoring,storing and analysing the concave plate sieve displacement of the picking device based on EasyBuilder Pro was designed,and the road monitoring test of displacement variation of concave plate sieve of the picking device and feeding rate was carried out.The linear function,power function,exponential function,quadratic function,compound function,logarithmic function and cubic function fitting were used to perform regression analysis of the test results by using IBM SPSS software.The results showed that the cubic function model had a higher fitting precision,and its determination coefficient was 0.992.Model verification experiments were proposed,and the results showed that the established cubic function model had a good accuracy.The absolute deviation rate ranged from 0 to 4.83%,and the average deviation rate was 2.22%.The deviation rate increased with an increasing feeding rate.The field experiments also proved that there was a cubic function relationship between the feeding rate and concave plate sieve displacement,the measured concave plate sieve displacement deviation rate ranged from 0 to 6.19%,and the average deviation rate was 2.73%compared with the calculated results.This study can provide a reference for the optimization design of the structure of full-feeding picking devices for peanuts and other crops and the intelligent measurement and control of the feeding rates.展开更多
The effect of a machine feeding rate(FR;1,1.5 and 2 Mg/h)and/or three levels of selected fineness degree(FD;3,5 and 7 mm)on machine performance,pellet physical parameters,required energy and production cost of three m...The effect of a machine feeding rate(FR;1,1.5 and 2 Mg/h)and/or three levels of selected fineness degree(FD;3,5 and 7 mm)on machine performance,pellet physical parameters,required energy and production cost of three main types of broilers diets were examined in this experiment.The examined broiler diets were formulated to meet the Ross 308 strain requirements.A complete factorial design(3×3×3)was used to identify the effects of studied factors on the pellet mill machine and pellet production.The obtained results indicated that the pellet mill productivity significantly(p˂0.001)improved through increased pellet mill feeding rate level.In addition,the machine pelleting efficiency was found to be significantly affected by all studied variables and their interactions.While the total power consumption of the machine showed no variations under the impact of the tested factors or with any of their combinations.Regarding the pellet physical quality indices,all broiler diets with all selected FD and lower FR had the maximum durability and bulk density levels.Furthermore,lower feeding rates were associated with higher hardness degrees.The lowest production costs were substantially correlated with high FR and intermediate FD(5 mm).Furthermore,production costs were determined to be reduced in finisher broiler diets under different feeding rates.Moreover,manufacturing costs of finisher broiler meals were observed to decrease in several feeding rates.Overall,these findings indicate the capabilities of producing high-quality pellets and reducing the needed production costs by optimizing feeding rates to 2 Mg/h and 2 mm fineness in broiler diets.展开更多
The objectives were to develop and evaluate: 1) growth rate models, 2) body lipid, moisture, and energy models for white sturgeon fed at various feeding rates(FR; % body weight [BW] per day) and then evaluate response...The objectives were to develop and evaluate: 1) growth rate models, 2) body lipid, moisture, and energy models for white sturgeon fed at various feeding rates(FR; % body weight [BW] per day) and then evaluate responses at proportions of optimum feeding rate(OFR) across increasing BW(g). For objective1,19 datasets from the literature containing initial BW, FR and specific growth rate(SGR; % BW increase per day) were used. For objective 2.12 datasets from the literature(11 from objective 1) containing SGR,FR,final BW,body lipid(%),protein(%),ash(%),moisture(%),and energy(kJ/g) were used. The average rearing temperatures was 19.2 ± 1.5 ℃(mean ± SD). The average nutrient compositions and gross energy of the diets were 45.7 ± 4.3% protein,14.8 ± 3.2% lipid, and 20.4 ± 1.3 kJ/g,respectively. The logistic model was used for objectives 1 and 2 to develop a statistical relationship between SGR and FR, then an iterative technique was used to estimate OFR for each dataset. For objective 2, the statistical relationship between body lipid, energy, and moisture and FR was established. Using the OFR estimate, SGR, body lipid, energy and moisture were computed at various FR as a proportion of OFR, Finally, a nonparametric fitting procedure was used to establish relationships between SGR, body lipid, energy and moisture(responses)compared with BW(predictor) at various proportions of OFR. This allows visualization of the effect of under-or over-feeding on the various responses. When examining the differences between OFR at 100%and various proportions of OFR, SGR differences decrease and moisture differences increase as BW increases. Lipid and energy differences decrease as BW increases. To our knowledge, these are the first description of changes in nutrient compositions when white sturgeon are fed at various FR. Because physiological and behavioral properties that are unique to sturgeon, results from this study are specific to sturgeon under the conditions of this study and cannot be compared directly with salmonids even if some of the results are similar. This research provides insight to designing future nutritional studies in sturgeon.展开更多
Three experimental groups with different feeding frequencies,different feeding rates and compensatory feeding were set up to study their effects on the growth of Micropterus salmoides.The results showed that different...Three experimental groups with different feeding frequencies,different feeding rates and compensatory feeding were set up to study their effects on the growth of Micropterus salmoides.The results showed that different feeding rates of 2%,3%and 4%had no significant effects on the growth of M.salmoides.Therefore,before the individual weight of 50 g,the fish could be fed with a feeding rate of 4%,which could be gradually decreased to 2%in the later period.Under the condition of relatively fixed feeding rate,different feeding frequencies had an impact on the growth of M.salmoides.Under the conditions of suitable water temperature,it is reasonable to feed twice daily.The experimental fish fed for 5 d and then deprived of feed for 1 d showed fully compensatory growth,and there were no significant differences in weight gain rate,daily weight gain and specific growth rate compared with the continuous feeding group(P>0.05).Therefore,according to the feeding conditions of fish in the breeding process,stopping feeding for 1 d every 5 d could save feed and labor and improve breeding efficiency.展开更多
Background: The optimal rate of feeding advancement after initiation of early enteral nutrition (EEN) for underweight, critically ill patients is unknown. Methods: We conducted a retrospective chart review in intensiv...Background: The optimal rate of feeding advancement after initiation of early enteral nutrition (EEN) for underweight, critically ill patients is unknown. Methods: We conducted a retrospective chart review in intensive care unit (ICU) patients with a body mass index (BMI) < 20.0 kg/m<sup>2</sup>. Patients were categorized into Group R, which reached the energy target within 3 days of EEN initiation, and Group S, which reached the energy target 4 or more days after EEN initiation. Results: A total of 65 patients with a median age of 73 years were included in the study. No significant differences were observed between the two groups for all-cause mortality, ICU-free days, or length of hospital stay. Ventilator-free days (VFDs) were significantly fewer in Group R than in Group S (18.0 [0.0 - 22.0] vs. 21.0 [16.3 - 24.8] days;P = 0.046). A significantly higher number of patients requiring mechanical ventilation (MV) at hospital discharge were observed in Group R than in Group S (29% vs. 8%;P = 0.030). Multivariable analyses with adjustment for confounders found that days required to reach target energy intake after EEN initiation were significantly and independently associated with the requirement for MV at hospital discharge, but not with VFDs. Conclusion: A slow rate of feeding advancement after initiation of EEN in critically ill patients having a BMI of <20.0 kg/m<sup>2</sup> might be associated with a reduced requirement for MV at hospital discharge. These results require confirmation in a large multicenter trial of underweight, critically ill patients.展开更多
Background:In bird species where offspring growth and survival rely on parents’food provisioning,parents can maximise their fitness by increasing the quantity and/or the quality of preys delivered to their offspring....Background:In bird species where offspring growth and survival rely on parents’food provisioning,parents can maximise their fitness by increasing the quantity and/or the quality of preys delivered to their offspring.Many studies have focused on inter-individual variation in feeding rate,yet this measure may not accurately reflect the total amount of food(i.e.energy)provided by parents if there is large variation in the quantity and quality of preys at each feeding.Here,we explored the relative role of individual(sex,age,body condition),breeding(hatching date,brood size)and environmental(temperature)factors on feeding rate,prey number,size and quality,and their contribution to total prey biomass delivered to the nestlings of 164 Collared Flycatcher(Ficedula albicollis)parents in 98 nests.Results:Preys delivered to the nest were mainly larvae(53.6%)and flying insects(45.6%).Feeding rate increased with brood size and age,and was higher in males than females.Mean prey number decreased,but mean prey size increased,as the season progressed and parents feeding their brood with primary larvae brought more preys per visit.Relationships between feeding rate,mean prey number and size remained when taking into account the provision-ing quality:parents brought either a large number of small prey or a small number of larger items,and the force of the trade-offs between feeding rate and mean prey number and size depended on the quality of the provisioning of the parents.Whatever the percentage of larvae among preys in the provisioning,the variance in total prey biomass was foremost explained by feeding rate(65.1%to 76.6%)compared to mean prey number(16.4%to 26%)and prey size(2.7%to 4%).Conclusions:Our study shows that variation in feeding rate,prey number,size,but not quality(i.e.percentage of lar-vae),were influenced by individual factors(sex and age)and breeding decisions(brood size and timing of breeding)and that,whatever the provisioning strategy adopted,feeding rate was the best proxy of the total biomass delivered to the nestlings.展开更多
Feeding rhythm of common carp was investigated from 4℃ to 34℃. The results indicated that there was a diel feeding rhythm for both adult (630-850 g) and youth (61-91 g) at all tested temperatures. There were two...Feeding rhythm of common carp was investigated from 4℃ to 34℃. The results indicated that there was a diel feeding rhythm for both adult (630-850 g) and youth (61-91 g) at all tested temperatures. There were two main activity peaks at 8:00-11:00 a.m. and 19:00-23:00 p.m., during which feeding quantities were 10.68%-32.53% and 16.25%-33.41% of the daily intake, respectively. When water temperature dropped to below 10℃, the feeding peak concentrated at 8:00-11:00 a.m. and 19:00 p.m. to 4:00 a.m. At 6℃, though both adult and youth would still feed, the feeding quantities were only 0.01% and 0.35% of body mass. Daily feeding rate of adult and youth reached 1.21% and 2.63% at 14℃, respectively. Both adult and youth carps reached the maximum daily feeding rate at 28℃, being 2.84% and 12.06% of body mass, respectively. The daily feeding rate of adult and youth reduced suddenly after at 34℃, and the daily feeding rate was only 0.74% and 9.45% of body mass, respectively. There was significant difference in daily feeding rate at different water temperatures (P〈0.05).展开更多
Considering machining efficiency, surface quality and wear of cutter and machine, it is necessary to maintain high, stable and constant surface feed rate as far as possible.The feed late control strategy for multi-axi...Considering machining efficiency, surface quality and wear of cutter and machine, it is necessary to maintain high, stable and constant surface feed rate as far as possible.The feed late control strategy for multi-axis CNC machining of free-form surfaces is presented. It comprises: ①the determination of effective feed rate; ②the adoption of suitable approaches to smooth feed rate. This strategy considers path geometry, actuator limitation and machine dynamics. The result shows that machining efficiency is improved effectively.展开更多
Friction stir processing (FSP), a variation of FSW (friction stir welding) is an emerging surface engineering technology that can locally eliminate casting defects and refine microstructures, thereby improving the...Friction stir processing (FSP), a variation of FSW (friction stir welding) is an emerging surface engineering technology that can locally eliminate casting defects and refine microstructures, thereby improving the mechanical properties of material. FSP can also produce fine grained microstructures through the thickness to impart superplasticity. The technology involves plunging a rapidly rotating, non consumable tool, comprising a profiled pin and larger diameter shoulder, into the surface and then traversing the tool across the surface. The pin and the shoulder friction heat the surface which alters the grain structure in the processed area thereby improving the mechanical properties. This paper presents the effects of FSP on microstructure and mechanical properties of extruded cast 2285 aluminum alloy at three different feed rates viz. 10, 12 and 15 mm/min. With the increase in the feed speed the material was observed to have increased impact strength. FSP also increased the tensile and yield strengths with increases in hardness and ductility values also. The observation has been listed in detail and pictorially represented.展开更多
Abstract Employing experimental-ecological methods, the feeding and vitality of adult Anthocidaris crassispina were investigated. The results showed that A. cras- sispina exhibited an obvious preference on five differ...Abstract Employing experimental-ecological methods, the feeding and vitality of adult Anthocidaris crassispina were investigated. The results showed that A. cras- sispina exhibited an obvious preference on five different seaweeds, with the preference order of Betaphycus gelatinum 〉 Sargassum hemiphyllum 〉 Gelidium amansii 〉 Ulva lactuca 〉 Codium fragile. The daily feed intake of A. crassispina differed among U. lactuca, S. hemiphyllum and B. gelatinum. The feeding was affected by water temperature, seaweed species and body weight. The optimal vitality and feed intake were observed under 23 -27℃, which were inhibited under whether too higher or too lower temperature. Under the optimal temperature for feeding, the daily feed intake of adult A. crassispina assumed an exponentially-decreasing trend with increase of body weight.展开更多
The metal transfer mode of electron beam welding (EBW) with filler wire was studied experimentally. The spatial position between the electron beam and the filler wire was defined. Basing on the charge coupled device...The metal transfer mode of electron beam welding (EBW) with filler wire was studied experimentally. The spatial position between the electron beam and the filler wire was defined. Basing on the charge coupled device (CCD) visual sensing system, the metal transfer mode of filler wire was investigated. The results showed that there were five transfer modes during EBW process due to different wire feed rates and spatial positions between beam and filler wire, such as short-circuiting mode, molten metal bridge mode, small droplet mode, big droplet mode and mixed mode. By comparing the weld appearance of different transfer modes, the molten metal bridge transfer was proved to be the best transfer mode.展开更多
Wire arc additive manufacturing(WAAM)has been investigated to deposit large-scale metal parts due to its high deposition efficiency and low material cost.However,in the process of automatically manufacturing the high-...Wire arc additive manufacturing(WAAM)has been investigated to deposit large-scale metal parts due to its high deposition efficiency and low material cost.However,in the process of automatically manufacturing the high-quality metal parts by WAAM,several problems about the heat build-up,the deposit-path optimization,and the stability of the process parameters need to be well addressed.To overcome these issues,a new WAAM method based on the double electrode micro plasma arc welding(DE-MPAW)was designed.The circuit principles of different metal-transfer models in the DE-MPAW deposition process were analyzed theoretically.The effects between the parameters,wire feed rate and torch stand-off distance,in the process of WAAM were investigated experimentally.In addition,a real-time DE-MPAW control system was developed to optimize and stabilize the deposition process by self-adaptively changing the wire feed rate and torch stand-off distance.Finally,a series of tests were performed to evaluate the control system’s performance.The results show that the capability against interferences in the process of WAAM has been enhanced by this self-adaptive adjustment system.Further,the deposition paths about the metal part’s layer heights in WAAM are simplified.Finally,the appearance of the WAAM-deposited metal layers is also improved with the use of the control system.展开更多
In the automatic CO_2 arc welding, the alteration of the vertical distance between the welding torch and the workpiece has a strong effect on the welding parameters such as welding current and voltage, with the result...In the automatic CO_2 arc welding, the alteration of the vertical distance between the welding torch and the workpiece has a strong effect on the welding parameters such as welding current and voltage, with the result that the appearance and quality of weld are not steady. To weaken the influence of the distance alteration, a method is put forward in the paper. The method is that the alternate wire-feed control is used for compensating the welding current. On the basis of theoretical analysis, a static numerical model for alternate wire-feed control is established. The experiments show that the model-based regulation of the wire feed rate can compensate the welding current and ensure the appearance of weld. When the alteration of vertical distance between the torch and the workpiece is greater, not only is the wire feed rate regulated, but the output voltage of the power source is adjusted to ensure the appearance and quality of weld.展开更多
Metal framework composites have higher mechanical properties in examination to metals over an extensive variety of working conditions. This makes them an alluring alternative in swapping metals for different building ...Metal framework composites have higher mechanical properties in examination to metals over an extensive variety of working conditions. This makes them an alluring alternative in swapping metals for different building applications. The present review is a study on the influence of composite titanium on the cutting parameters, mechanical behavior, reinforcements, structure and nanostructure. This review will provide an understanding into selecting the optimum machining parameters for machining titanium composites. It’s also an attempt to give brief explanation by suitably machining the titanium composite which can be made reasonable.展开更多
Turning clearance angle is changed machining characteristics. In this study, the experiments start from choosing two workpiece materials that are machine structural carbon steel, chrome-molyb- denum steel. Then, the e...Turning clearance angle is changed machining characteristics. In this study, the experiments start from choosing two workpiece materials that are machine structural carbon steel, chrome-molyb- denum steel. Then, the experiments show specifically how features of selected materials changed when they were processed with machining operation. In order to find the surface roughness of workpiece materials, the workpiece materials which have higher tensile strength showed much better value of surface roughness in a surface roughness tester. Moreover, process feed rate was compared between 0.05 mm/rev and 0.10 mm/rev. When process feed rate was 0.05 mm/rev, surface roughness has superior results without reference to the quality of the materials.展开更多
Crops are prone to lodging with the decline of stem moisture and the intervention of other factors in the mature harvest period,such as garlic,which is difficult to harvest mechanically.To solve this problem,the plant...Crops are prone to lodging with the decline of stem moisture and the intervention of other factors in the mature harvest period,such as garlic,which is difficult to harvest mechanically.To solve this problem,the plant-correcting reel for harvesting lodging garlic plants,bumped and deformed with plants many times to pull and lift them into a conveyor,is proposed in this study.We analyzed the motion trajectory equation and key influencing factors of the reel and defined the lifting and plant-correcting stages as three processes of contact,stirring and release.For example,the contact deformation model and system energy equations were established in the contact process.Besides,in the stirring process,the garlic plant-correcting conditions were established through the dynamic simulation test analysis of garlic seedling trajectories and the deflection model of garlic stem was constructed.Furthermore,in the release process,the expressions of rubber bars rotation and garlic plant offset bending curvature were constructed and the optimal number and distribution form of bars were determined.Meanwhile,the mechanism and key operating parameters of the auxiliary lifting mechanism of the divider were established.Through the single-factor test,the influence of reel speed,forward speed and reel height on the success feeding rate was analyzed under different bars distribution forms;Through multi-factor experiments,the interaction contour map of various factors was constructed.When reel speed,forward speed and reel height were 3 rad/s,3.5 m/s,and 540 mm,the feeding success rate was 98.73%.The optimization factors were tested and verified,which met the operational requirements of a high feeding success rate and low loss rate of garlic harvest.This study combines laboratory virtual as well as field experiments and analyzes of trajectory of bars,contact deformation and deflection model of garlic plant,and reel rotation and garlic plant offset bending curvature to solve the problem of garlic lodging mechanized harvest and yield reduction.展开更多
Electrochemical machining(ECM)is an economical and effective method for blisk manufacturing and includes two steps:channel machining and profile machining.The allowance distribution after the channel machining will di...Electrochemical machining(ECM)is an economical and effective method for blisk manufacturing and includes two steps:channel machining and profile machining.The allowance distribution after the channel machining will directly affect the profile machining.Therefore,to improve the uniformity of allowance distribution in the machining of channels,a method that incorporates a variable feed rate mode is developed.During the machining process,the feed rates are dynamically changed according to the needs of the side gap at the different feed depths.As a result,the side gaps at the different feed depths vary,contributing to a decrease in the allowance difference.In this study,the dissolution processes of a blisk channel are simulated using different feed rates,and prediction profiles are obtained.Based on the prediction profiles,the relationship among the feed rate,feed depth,and side gap is established.Then,the feed rates at different feed depths are adjusted according to the relationship.In addition,contrast experiments are conducted.Compared with blisk channel ECM using a constant feed rate of 1 mm/min,using the variable feed rate decreases the allowance differences in the convex and concave parts by 62.2%and 67.4%,respectively.This indicates that using the variable feed rate in the ECM process for a blisk channel is feasible and efficient.展开更多
A numerical model was established to calculate the cycle feed rate through studying the case of a cold pilger mill with the 304 stainless steel pipe. Firstly, the precise constitutive equation of 304 stainless steel w...A numerical model was established to calculate the cycle feed rate through studying the case of a cold pilger mill with the 304 stainless steel pipe. Firstly, the precise constitutive equation of 304 stainless steel was obtained through nonlinearly fitting the true stress-strain data from unidirectional tensile test. Then, the numerical method to calculate the equivalent deformation was determined according to the plastic deformation feature of the steel tube during cold rolling and the incremental theory. Finally, the cycle feed rate of cold roiled 304 stainless steel pipe was extracted when formulating springback through utilizing above results comprehensively and unloading law. Stress state, metal flow, finished pipe size and distribution of residual stress were obtained by finite element method to calculate the whole rolling process when the cycle feed rate was 10 mm, and the optimized model was verified through finished pipe size.展开更多
基金supported financially by Yangjiang City Hardware Knives and Scissors and Nickel Alloy Industry Additive Manufacturing Technology Innovation Platform Construction(No.2015B020221002)Guangdong Province‘Sailing Plan’Introduces Special Funding for Innovation and Entrepreneurship Team(No.2015YT02G090)+1 种基金High-end Knives and Scissors Additive Manufacturing(3D Printing)of Engineering Technology Research Center in Guangdong Province(Grant No.509153168061)Initial Construction Subsidy for New Research and Development Institutions of Yangjiang City Hardware Knives and Scissors Industry and Technology Research(Grant No.611229498090)。
文摘The growing interest in additive manufacturing of GH4169 alloy was accompanied by the demand on spherical GH4169 powders with high performance.The powder particles were treated by radio frequency plasma with the different feeding rates.The microstructure and morphology,the particle size distribution of as-treated powders were studied by scanning electron microscopy and laser particle size analysis.It was demonstrated that GH4169 powders with extremely fine followability were obtained by radio frequency plasma spheroidization technology.With the same plasma parameters,the spheroidization efficiency of the particles varied with the feeding rates.When the rate of the powder feeding rates was too small,the excessive absorption of the heating by the powders caused vaporization,then the collection decreased.When the feeding rates was too large,the powder particles were insufficiently absorbed,resulting in defects in the powders.The microstructure of the as-treated spherical particles was mainly cell crystals,columnar crystals,and even microcrystals.Under the suitable plasma parameters,the resulting powders haved a slightly increased average particle size,excellent spheroidization,surface smoothness,followability,and bulk ratio.
文摘Determining the suitable fish farming conditions for optimal growth is necessary for aquaculture production, but it is not very obvious because it requires a good understanding of species biology. Thus, this study aims to evaluate the effects of different temperature regimes, stocking densities, and feeding rates on the growth of Nile tilapia, Oreochromis niloticus fingerlings that have been sex-reversed with 17α methyl testosterone. Three independent experiments were performed (with replicates) at the IRD Bel-Air fish farm (Dakar, Senegal) on 27-day-old fry maintained in six 25 L tanks with a batch of 100 individuals each. These fry were subjected to three different temperatures (26˚C, 28˚C, 30˚C;kept constant with thermostats), stocking densities (5, 10 and 15 ind/l) and feeding rates (5%, 10% and 15% of biomass;distributed three times a day). For the temperature and density treatments, fry was fed a pelleted feed containing 38% protein, distributed by hand at 10% of their total biomass, readjusted after each measurement. Growth performance (total weight, weight gain and daily weight gain), physicochemical parameters (temperature, oxygen, nitrite and phosphorus), feed conversion ratio (FCR) and survival rate (SR) were regularly monitored (weekly) during the experimental period. For the heat treatment, the results did not show an apparent relationship between growth performance and nitrite, phosphorus or dissolved oxygen (DO) contents. In contrast, there was a significant correlation between temperature and growth rates, with the best growth being obtained at 30˚C compared to 28˚C and 26˚C. Similarly, growth rates were correlated with stocking density and feeding rate but not with oxygen, temperature, nitrite or phosphorus levels. The best growth rates were observed at the lowest density (5 ind/l) and for the highest feeding rate (15% of biomass), which coincides with the best FCR and survival rates. Thus, 30˚C, 5 ind/l and 15% of biomass appeared to be the most favorable temperature, stocking density and feeding rate for optimal growth of Nile tilapia fry after inversion. The application of these results in the culture systems will allow to reach a good production of O. niloticus and thus to contribute to sustainable development of fish culture in Senegal.
基金supported by the Jiangsu Agricultural Science and Technology Innovation Fund (Grant No.CX (23)3028)National Natural Science Foundation of China (Grant No.52105263)+2 种基金Key Laboratory of Modern Agricultural Intelligent Equipment in South China,Ministry of Agriculture and Rural Affairs,China (HNZJ202201)Key Laboratory of Intelligent Equipment and Robotics for Agriculture of Zhejiang Province (Grant No.2022ZJZD2201)Key Laboratory of Agricultural Equipment for Hilly and Mountainous Areas in Southeastern China (Co-construction by Ministry and Province),Ministry of Agriculture and Rural Affairs (Grant No.QSKF2023004).
文摘To improve the declining performance of a full-feed peanut picking device or solve the mechanical failures that occur due to fluctuations in the feeding rate during operation,the 4HLJI-3000 peanut intelligent picking combine harvester,which is a picking device with a self-adaptive adjustment of the working clearance,was developed as the research object in this study.Moreover,the key components,such as the picking roller,concave plate sieve and clearance adjustment mechanism of the concave plate sieve,were designed and analysed.Through the force analysis of the concave plate sieve of the picking device,the mathematical model of the concave plate sieve displacement of the picking device and feeding rate was obtained.The software system for monitoring,storing and analysing the concave plate sieve displacement of the picking device based on EasyBuilder Pro was designed,and the road monitoring test of displacement variation of concave plate sieve of the picking device and feeding rate was carried out.The linear function,power function,exponential function,quadratic function,compound function,logarithmic function and cubic function fitting were used to perform regression analysis of the test results by using IBM SPSS software.The results showed that the cubic function model had a higher fitting precision,and its determination coefficient was 0.992.Model verification experiments were proposed,and the results showed that the established cubic function model had a good accuracy.The absolute deviation rate ranged from 0 to 4.83%,and the average deviation rate was 2.22%.The deviation rate increased with an increasing feeding rate.The field experiments also proved that there was a cubic function relationship between the feeding rate and concave plate sieve displacement,the measured concave plate sieve displacement deviation rate ranged from 0 to 6.19%,and the average deviation rate was 2.73%compared with the calculated results.This study can provide a reference for the optimization design of the structure of full-feeding picking devices for peanuts and other crops and the intelligent measurement and control of the feeding rates.
文摘The effect of a machine feeding rate(FR;1,1.5 and 2 Mg/h)and/or three levels of selected fineness degree(FD;3,5 and 7 mm)on machine performance,pellet physical parameters,required energy and production cost of three main types of broilers diets were examined in this experiment.The examined broiler diets were formulated to meet the Ross 308 strain requirements.A complete factorial design(3×3×3)was used to identify the effects of studied factors on the pellet mill machine and pellet production.The obtained results indicated that the pellet mill productivity significantly(p˂0.001)improved through increased pellet mill feeding rate level.In addition,the machine pelleting efficiency was found to be significantly affected by all studied variables and their interactions.While the total power consumption of the machine showed no variations under the impact of the tested factors or with any of their combinations.Regarding the pellet physical quality indices,all broiler diets with all selected FD and lower FR had the maximum durability and bulk density levels.Furthermore,lower feeding rates were associated with higher hardness degrees.The lowest production costs were substantially correlated with high FR and intermediate FD(5 mm).Furthermore,production costs were determined to be reduced in finisher broiler diets under different feeding rates.Moreover,manufacturing costs of finisher broiler meals were observed to decrease in several feeding rates.Overall,these findings indicate the capabilities of producing high-quality pellets and reducing the needed production costs by optimizing feeding rates to 2 Mg/h and 2 mm fineness in broiler diets.
基金supported by the Department of Animal Science, College of Agriculture and Environmental Science, and the California Agricultural Experiment Station of the University of California-Davis
文摘The objectives were to develop and evaluate: 1) growth rate models, 2) body lipid, moisture, and energy models for white sturgeon fed at various feeding rates(FR; % body weight [BW] per day) and then evaluate responses at proportions of optimum feeding rate(OFR) across increasing BW(g). For objective1,19 datasets from the literature containing initial BW, FR and specific growth rate(SGR; % BW increase per day) were used. For objective 2.12 datasets from the literature(11 from objective 1) containing SGR,FR,final BW,body lipid(%),protein(%),ash(%),moisture(%),and energy(kJ/g) were used. The average rearing temperatures was 19.2 ± 1.5 ℃(mean ± SD). The average nutrient compositions and gross energy of the diets were 45.7 ± 4.3% protein,14.8 ± 3.2% lipid, and 20.4 ± 1.3 kJ/g,respectively. The logistic model was used for objectives 1 and 2 to develop a statistical relationship between SGR and FR, then an iterative technique was used to estimate OFR for each dataset. For objective 2, the statistical relationship between body lipid, energy, and moisture and FR was established. Using the OFR estimate, SGR, body lipid, energy and moisture were computed at various FR as a proportion of OFR, Finally, a nonparametric fitting procedure was used to establish relationships between SGR, body lipid, energy and moisture(responses)compared with BW(predictor) at various proportions of OFR. This allows visualization of the effect of under-or over-feeding on the various responses. When examining the differences between OFR at 100%and various proportions of OFR, SGR differences decrease and moisture differences increase as BW increases. Lipid and energy differences decrease as BW increases. To our knowledge, these are the first description of changes in nutrient compositions when white sturgeon are fed at various FR. Because physiological and behavioral properties that are unique to sturgeon, results from this study are specific to sturgeon under the conditions of this study and cannot be compared directly with salmonids even if some of the results are similar. This research provides insight to designing future nutritional studies in sturgeon.
基金Supported by Key R&D Program of Hubei Province(2022BBA0058)。
文摘Three experimental groups with different feeding frequencies,different feeding rates and compensatory feeding were set up to study their effects on the growth of Micropterus salmoides.The results showed that different feeding rates of 2%,3%and 4%had no significant effects on the growth of M.salmoides.Therefore,before the individual weight of 50 g,the fish could be fed with a feeding rate of 4%,which could be gradually decreased to 2%in the later period.Under the condition of relatively fixed feeding rate,different feeding frequencies had an impact on the growth of M.salmoides.Under the conditions of suitable water temperature,it is reasonable to feed twice daily.The experimental fish fed for 5 d and then deprived of feed for 1 d showed fully compensatory growth,and there were no significant differences in weight gain rate,daily weight gain and specific growth rate compared with the continuous feeding group(P>0.05).Therefore,according to the feeding conditions of fish in the breeding process,stopping feeding for 1 d every 5 d could save feed and labor and improve breeding efficiency.
文摘Background: The optimal rate of feeding advancement after initiation of early enteral nutrition (EEN) for underweight, critically ill patients is unknown. Methods: We conducted a retrospective chart review in intensive care unit (ICU) patients with a body mass index (BMI) < 20.0 kg/m<sup>2</sup>. Patients were categorized into Group R, which reached the energy target within 3 days of EEN initiation, and Group S, which reached the energy target 4 or more days after EEN initiation. Results: A total of 65 patients with a median age of 73 years were included in the study. No significant differences were observed between the two groups for all-cause mortality, ICU-free days, or length of hospital stay. Ventilator-free days (VFDs) were significantly fewer in Group R than in Group S (18.0 [0.0 - 22.0] vs. 21.0 [16.3 - 24.8] days;P = 0.046). A significantly higher number of patients requiring mechanical ventilation (MV) at hospital discharge were observed in Group R than in Group S (29% vs. 8%;P = 0.030). Multivariable analyses with adjustment for confounders found that days required to reach target energy intake after EEN initiation were significantly and independently associated with the requirement for MV at hospital discharge, but not with VFDs. Conclusion: A slow rate of feeding advancement after initiation of EEN in critically ill patients having a BMI of <20.0 kg/m<sup>2</sup> might be associated with a reduced requirement for MV at hospital discharge. These results require confirmation in a large multicenter trial of underweight, critically ill patients.
文摘Background:In bird species where offspring growth and survival rely on parents’food provisioning,parents can maximise their fitness by increasing the quantity and/or the quality of preys delivered to their offspring.Many studies have focused on inter-individual variation in feeding rate,yet this measure may not accurately reflect the total amount of food(i.e.energy)provided by parents if there is large variation in the quantity and quality of preys at each feeding.Here,we explored the relative role of individual(sex,age,body condition),breeding(hatching date,brood size)and environmental(temperature)factors on feeding rate,prey number,size and quality,and their contribution to total prey biomass delivered to the nestlings of 164 Collared Flycatcher(Ficedula albicollis)parents in 98 nests.Results:Preys delivered to the nest were mainly larvae(53.6%)and flying insects(45.6%).Feeding rate increased with brood size and age,and was higher in males than females.Mean prey number decreased,but mean prey size increased,as the season progressed and parents feeding their brood with primary larvae brought more preys per visit.Relationships between feeding rate,mean prey number and size remained when taking into account the provision-ing quality:parents brought either a large number of small prey or a small number of larger items,and the force of the trade-offs between feeding rate and mean prey number and size depended on the quality of the provisioning of the parents.Whatever the percentage of larvae among preys in the provisioning,the variance in total prey biomass was foremost explained by feeding rate(65.1%to 76.6%)compared to mean prey number(16.4%to 26%)and prey size(2.7%to 4%).Conclusions:Our study shows that variation in feeding rate,prey number,size,but not quality(i.e.percentage of lar-vae),were influenced by individual factors(sex and age)and breeding decisions(brood size and timing of breeding)and that,whatever the provisioning strategy adopted,feeding rate was the best proxy of the total biomass delivered to the nestlings.
文摘Feeding rhythm of common carp was investigated from 4℃ to 34℃. The results indicated that there was a diel feeding rhythm for both adult (630-850 g) and youth (61-91 g) at all tested temperatures. There were two main activity peaks at 8:00-11:00 a.m. and 19:00-23:00 p.m., during which feeding quantities were 10.68%-32.53% and 16.25%-33.41% of the daily intake, respectively. When water temperature dropped to below 10℃, the feeding peak concentrated at 8:00-11:00 a.m. and 19:00 p.m. to 4:00 a.m. At 6℃, though both adult and youth would still feed, the feeding quantities were only 0.01% and 0.35% of body mass. Daily feeding rate of adult and youth reached 1.21% and 2.63% at 14℃, respectively. Both adult and youth carps reached the maximum daily feeding rate at 28℃, being 2.84% and 12.06% of body mass, respectively. The daily feeding rate of adult and youth reduced suddenly after at 34℃, and the daily feeding rate was only 0.74% and 9.45% of body mass, respectively. There was significant difference in daily feeding rate at different water temperatures (P〈0.05).
基金This project is supported by National Natural Science Foundation of China and the Eight-Five Year Plan National Key Projects. Ma
文摘Considering machining efficiency, surface quality and wear of cutter and machine, it is necessary to maintain high, stable and constant surface feed rate as far as possible.The feed late control strategy for multi-axis CNC machining of free-form surfaces is presented. It comprises: ①the determination of effective feed rate; ②the adoption of suitable approaches to smooth feed rate. This strategy considers path geometry, actuator limitation and machine dynamics. The result shows that machining efficiency is improved effectively.
文摘Friction stir processing (FSP), a variation of FSW (friction stir welding) is an emerging surface engineering technology that can locally eliminate casting defects and refine microstructures, thereby improving the mechanical properties of material. FSP can also produce fine grained microstructures through the thickness to impart superplasticity. The technology involves plunging a rapidly rotating, non consumable tool, comprising a profiled pin and larger diameter shoulder, into the surface and then traversing the tool across the surface. The pin and the shoulder friction heat the surface which alters the grain structure in the processed area thereby improving the mechanical properties. This paper presents the effects of FSP on microstructure and mechanical properties of extruded cast 2285 aluminum alloy at three different feed rates viz. 10, 12 and 15 mm/min. With the increase in the feed speed the material was observed to have increased impact strength. FSP also increased the tensile and yield strengths with increases in hardness and ductility values also. The observation has been listed in detail and pictorially represented.
基金Supported by National Key Technology R&D Program of China(2012BAD-18B02,2012BAD18B01-2)Public Science and Technology Research Funds Projects of Ocean(201205021-3)Special Scientific Research Funds for Central Non-profit Institutes(South China Sea Fisheries Research Institute,Chinese Academy of Fishery Sciences)(2014TS07,2015TS05)
文摘Abstract Employing experimental-ecological methods, the feeding and vitality of adult Anthocidaris crassispina were investigated. The results showed that A. cras- sispina exhibited an obvious preference on five different seaweeds, with the preference order of Betaphycus gelatinum 〉 Sargassum hemiphyllum 〉 Gelidium amansii 〉 Ulva lactuca 〉 Codium fragile. The daily feed intake of A. crassispina differed among U. lactuca, S. hemiphyllum and B. gelatinum. The feeding was affected by water temperature, seaweed species and body weight. The optimal vitality and feed intake were observed under 23 -27℃, which were inhibited under whether too higher or too lower temperature. Under the optimal temperature for feeding, the daily feed intake of adult A. crassispina assumed an exponentially-decreasing trend with increase of body weight.
文摘The metal transfer mode of electron beam welding (EBW) with filler wire was studied experimentally. The spatial position between the electron beam and the filler wire was defined. Basing on the charge coupled device (CCD) visual sensing system, the metal transfer mode of filler wire was investigated. The results showed that there were five transfer modes during EBW process due to different wire feed rates and spatial positions between beam and filler wire, such as short-circuiting mode, molten metal bridge mode, small droplet mode, big droplet mode and mixed mode. By comparing the weld appearance of different transfer modes, the molten metal bridge transfer was proved to be the best transfer mode.
基金Supported by National Natural Science Foundation of China(Grant No.51665034).
文摘Wire arc additive manufacturing(WAAM)has been investigated to deposit large-scale metal parts due to its high deposition efficiency and low material cost.However,in the process of automatically manufacturing the high-quality metal parts by WAAM,several problems about the heat build-up,the deposit-path optimization,and the stability of the process parameters need to be well addressed.To overcome these issues,a new WAAM method based on the double electrode micro plasma arc welding(DE-MPAW)was designed.The circuit principles of different metal-transfer models in the DE-MPAW deposition process were analyzed theoretically.The effects between the parameters,wire feed rate and torch stand-off distance,in the process of WAAM were investigated experimentally.In addition,a real-time DE-MPAW control system was developed to optimize and stabilize the deposition process by self-adaptively changing the wire feed rate and torch stand-off distance.Finally,a series of tests were performed to evaluate the control system’s performance.The results show that the capability against interferences in the process of WAAM has been enhanced by this self-adaptive adjustment system.Further,the deposition paths about the metal part’s layer heights in WAAM are simplified.Finally,the appearance of the WAAM-deposited metal layers is also improved with the use of the control system.
文摘In the automatic CO_2 arc welding, the alteration of the vertical distance between the welding torch and the workpiece has a strong effect on the welding parameters such as welding current and voltage, with the result that the appearance and quality of weld are not steady. To weaken the influence of the distance alteration, a method is put forward in the paper. The method is that the alternate wire-feed control is used for compensating the welding current. On the basis of theoretical analysis, a static numerical model for alternate wire-feed control is established. The experiments show that the model-based regulation of the wire feed rate can compensate the welding current and ensure the appearance of weld. When the alteration of vertical distance between the torch and the workpiece is greater, not only is the wire feed rate regulated, but the output voltage of the power source is adjusted to ensure the appearance and quality of weld.
文摘Metal framework composites have higher mechanical properties in examination to metals over an extensive variety of working conditions. This makes them an alluring alternative in swapping metals for different building applications. The present review is a study on the influence of composite titanium on the cutting parameters, mechanical behavior, reinforcements, structure and nanostructure. This review will provide an understanding into selecting the optimum machining parameters for machining titanium composites. It’s also an attempt to give brief explanation by suitably machining the titanium composite which can be made reasonable.
文摘Turning clearance angle is changed machining characteristics. In this study, the experiments start from choosing two workpiece materials that are machine structural carbon steel, chrome-molyb- denum steel. Then, the experiments show specifically how features of selected materials changed when they were processed with machining operation. In order to find the surface roughness of workpiece materials, the workpiece materials which have higher tensile strength showed much better value of surface roughness in a surface roughness tester. Moreover, process feed rate was compared between 0.05 mm/rev and 0.10 mm/rev. When process feed rate was 0.05 mm/rev, surface roughness has superior results without reference to the quality of the materials.
基金China Agriculture Research System of MOF and MARA(CARS-24-D-01)National Key R&D Program of China(Grant No.2023YFD2001200)Shandong Province focuses on supporting the introduction of urgently needed and scarce talent projects in the region.
文摘Crops are prone to lodging with the decline of stem moisture and the intervention of other factors in the mature harvest period,such as garlic,which is difficult to harvest mechanically.To solve this problem,the plant-correcting reel for harvesting lodging garlic plants,bumped and deformed with plants many times to pull and lift them into a conveyor,is proposed in this study.We analyzed the motion trajectory equation and key influencing factors of the reel and defined the lifting and plant-correcting stages as three processes of contact,stirring and release.For example,the contact deformation model and system energy equations were established in the contact process.Besides,in the stirring process,the garlic plant-correcting conditions were established through the dynamic simulation test analysis of garlic seedling trajectories and the deflection model of garlic stem was constructed.Furthermore,in the release process,the expressions of rubber bars rotation and garlic plant offset bending curvature were constructed and the optimal number and distribution form of bars were determined.Meanwhile,the mechanism and key operating parameters of the auxiliary lifting mechanism of the divider were established.Through the single-factor test,the influence of reel speed,forward speed and reel height on the success feeding rate was analyzed under different bars distribution forms;Through multi-factor experiments,the interaction contour map of various factors was constructed.When reel speed,forward speed and reel height were 3 rad/s,3.5 m/s,and 540 mm,the feeding success rate was 98.73%.The optimization factors were tested and verified,which met the operational requirements of a high feeding success rate and low loss rate of garlic harvest.This study combines laboratory virtual as well as field experiments and analyzes of trajectory of bars,contact deformation and deflection model of garlic plant,and reel rotation and garlic plant offset bending curvature to solve the problem of garlic lodging mechanized harvest and yield reduction.
基金the National Science and Technology Major Project(No.2017-VII-0004-0097)the Natural Science Foundation for Distinguished Young Scholars of Jiangsu Province(No.BK20170031)。
文摘Electrochemical machining(ECM)is an economical and effective method for blisk manufacturing and includes two steps:channel machining and profile machining.The allowance distribution after the channel machining will directly affect the profile machining.Therefore,to improve the uniformity of allowance distribution in the machining of channels,a method that incorporates a variable feed rate mode is developed.During the machining process,the feed rates are dynamically changed according to the needs of the side gap at the different feed depths.As a result,the side gaps at the different feed depths vary,contributing to a decrease in the allowance difference.In this study,the dissolution processes of a blisk channel are simulated using different feed rates,and prediction profiles are obtained.Based on the prediction profiles,the relationship among the feed rate,feed depth,and side gap is established.Then,the feed rates at different feed depths are adjusted according to the relationship.In addition,contrast experiments are conducted.Compared with blisk channel ECM using a constant feed rate of 1 mm/min,using the variable feed rate decreases the allowance differences in the convex and concave parts by 62.2%and 67.4%,respectively.This indicates that using the variable feed rate in the ECM process for a blisk channel is feasible and efficient.
基金The authors are grateful for the financial assis- tance from the National Science Foundation of China (U1710113), the China Postdoctoral Science Foundation (2017M622903), the Fund for Shanxi Key Subjects Construction, Excellent innovation projects of graduate students in Shanxi (2017SY077), Heavy Machinery Engineering Research Center of Ministry of Education (20172004).
文摘A numerical model was established to calculate the cycle feed rate through studying the case of a cold pilger mill with the 304 stainless steel pipe. Firstly, the precise constitutive equation of 304 stainless steel was obtained through nonlinearly fitting the true stress-strain data from unidirectional tensile test. Then, the numerical method to calculate the equivalent deformation was determined according to the plastic deformation feature of the steel tube during cold rolling and the incremental theory. Finally, the cycle feed rate of cold roiled 304 stainless steel pipe was extracted when formulating springback through utilizing above results comprehensively and unloading law. Stress state, metal flow, finished pipe size and distribution of residual stress were obtained by finite element method to calculate the whole rolling process when the cycle feed rate was 10 mm, and the optimized model was verified through finished pipe size.