The Analysis on Comparison of Forming Condition with Abroad Palaeo-Epicontinental Marine Basin and Possibility of Potash Formation in North China

1 Introduction Currently,all six different continents have discovered potash deposits and potash-bearing salt lake saline water.However,the distribution is extremely uneven,which is mostly concentrated in Canada,Russia,Middle-Asia and

The Initial Tangent of the Femoral Arterial Pressure Increase Is an Estimate of Left Ventricular Contractility in Patients Undergoing Cardiacsurgery

Purpose: Assessment of contractile function is a major challenge in patients with left ventricular dysfunction, especially during cardiac surgery. The initial tangent of the femoral arterial pressure increase (tanin) has recently been described to be an estimate of left ventricular (LV) contractility. To confirm these findings tanin was compared to various indices of LV performance in patients undergoing cardiac surgery. Methods: Data from 17 patients were evaluated retrospectively. Myocardial performance was estimated by the echocardiographic indices ejection fraction (EF), shortening fraction (FS), circumferential fiber shortening velocity (Vcf), the parameters of pulse contour analysis area under the curve (AUC) and tanin. Measurements were taken before and after cardiopulmonary bypass (CPB). Results: Tanin increased significantly (813 ± 216 mmHg/s vs. 1490 ± 450 mmHg/s, p < 0.05) after CPB, as well as Vcf (0.89 ± 0.14 circ/s vs. 1.47 ± 0.27 circ/s, p < 0.05) and EF (65% ± 7% vs. 74% ± 6%, p < 0.05). FS did not change (40.7% ± 7% vs. 46.5% ± 5%, p = 0.30). AUC significantly dropped after CPB (435 ± 54 mmHg*s vs. 263 ± 27 mmHg*s). Tanin and Vcf correlated strongly (r = 0.70, p < 0.001), while tanin showed only weak correlation with EF (r = 0.36, p = 0.037). There was no significant correlation with FS (r = 0.31, p = 0.079). Tanin and AUC correlated inversely (r = -0.62, p < 0.001). Conclusions: While showing little or no correlation with EF and FS respectively, tanin correlated well with the less preload-dependent parameter Vcf, thus suggesting that tanin may be used as an easily accessible estimate of LV contractility during cardiac surgery.

FEM-based strain analysis study for multilayer sheet forming process

Fiber metal laminates have many advantages over traditional laminates （e.g., any type of fiber and resin material can be placed anywhere between the metallic layers without risk of failure of the composite fabric sheets）. Furthermore, the process requirements to strictly control the temperature and punch force in fiber metal laminates are also less stringent than those in traditional laminates. To further explore the novel method, this study conducts a finite element method-based （FEM-based） strain analysis on multilayer blanks by using the 3A method. Different forming modes such as wrinkling and fracture are discussed by using experimental and numerical studies. Hydroforming is used for multilayer forming. The Barlat 2000 yield criteria and DYNAFORM/LS-DYNA are used for the simulations. Optimal process parameters are determined on the basis of fixed die-binder gap and variable cavity pressure. The results of this study will enhance the knowledge on the mechanics of multilayer structures formed by using the 3A method and expand its commercial applications.

An analysis of As_2S_3 chirped fiber grating formed by two-photon absorption effect

When femtosecond laser pulses interfere with chirped femtosecond laser pulses in As2S3 fiber, a chirped fiber grating is formed. An analytical expression is given to describe the chirped grating, and its Bragg reflectivity is calculated. Because of the high photosensitive effect of As2S3 material, the chirped fiber grating has a wide Bragg reflective spectrum and high reflectivity by choosing proper parameters. This indicates that the chirped fiber grating can be used as a stretcher in the femtosecond chirped pulse amplification (CPA) system.

Research on deformation characteristics of JCOE forming in large diameter welding pipe

In the present work, the JCOE forming is inves- tigated using the finite element （FE） method. A two- dimensional FE model is established for the plane strain condition by FE code ABAQUS, and the FE model is vali- dated by experiments. The aim of this research is to inves- tigate forming quality states in the JCOE forming process; in particular, the effects of technological parameters on form- ing quality are evaluated. Taking the JCOE forming process of X80 steel φ1 219 mm × 22 mm × 12 000 mmwelding pipe for instance, the deformation characteristics of JCOE forming are analyzed, in which the geometry of the formed pipe, residual stress distributions and effects of process parameters on JCOE forming quality can be obtained. Thus, the presented results of this research provide an effective approach to improve welding pipe forming quality.

Prediction of Forming Limit Diagrams for Materials with HCP Structure

The forming limit diagram（FLD） is an important tool to be used when characterizing the formability of metallic sheets used in metal forming processes. Experimental measurement and determination of the FLD is timeconsuming and therefore the analytical prediction based on theory of plasticity and instability criteria allows a direct and efficient methodology to obtain critical values at different loading paths, thus carrying significant practical importance.However, the accuracy of the plastic instability prediction is strongly dependent on the choice of the material constitutive model [1–3]. Particularly for materials with hexagonal close packed（HCP） crystallographic structure, they have a very limited number of active slip systems at room temperature and demonstrate a strong asymmetry between yielding in tension and compression [4, 5]. Not only the magnitude of the yield locus changes, but also the shape of the yield surface is evolving during the plastic deformation [4]. Conventional phenomenological constitutive models of plasticity fail to capture this unconventional mechanical behavior [4, 6]. Cazacu and Plunkett [6] have proposed generic yield criteria, by using the transformed principal stress, to account for the initial plastic anisotropy and strength differential（SD） effect simultaneously. In this contribution, a generic FLD MATLAB script was developed based on Marciniak–Kuczynski analytical theory and applied to predict the localized necking. The influence of asymmetrical effect on the FLD was evaluated. Several yield functions such as von Mises, Hill, Barlat89, and Cazacu06 were incorporated into analysis. The paper also presents and discusses the influence of different hardening laws on the formability of materials with HCP crystal structures. The findings indicate that the plastic instability theory coupled with Cazacu model can adequately predict the onset of localized necking for HCP materials under different strain paths.