Formation Characteristics of CO_(2) Hydrates in the Presence of Porous Media and NaCl

Hydrate-based CO_(2) sequestration is an effective method for reducing the greenhouse effect,and the presence of porous media and NaCl can impact the formation characteristics of hydrates.This study uses the constant volume temperature search method to investigate the effects of quartz sand particle size(0.006‒0.03 mm),water saturation(30%–90%),and NaCl concentration(1%‒9%)on the phase equilibrium and kinetics of CO_(2) hydrates within a temperature range of 273‒285 K and pressure range of 1.0‒3.5 MPa.The results indicate that a decrease in quartz sand particle size or an increase in NaCl concentration shifts the hydrate phase equilibrium curve towards lower temperatures and higher pressures,making hydrate generation conditions more demanding.In different particle size systems,there are no significant changes in the rate of CO_(2) hydrate formation or conversion rate.The highest hydrate conversion rate of 71.1%is observed in a 0.015 mm particle size system.With increasing water saturation,both the generation rate and conversion rate of CO_(2) hydrates show a trend of first increasing and then decreasing.Meanwhile,low concentrations of NaCl(1%–3%)are found to enhance the formation and conversion rates of CO_(2) hydrates.However,as NaCl concentration increases,the rate of CO_(2) hydrate formation and conversion rate decrease.

Formation Characteristics of Calcium Ferrite in Low Silicon Sinter

Influence of sintering temperature, basicity and MgO content on the formation characteristics of calcium ferrite in low silicon sinter of Baotou Iron and Steel Company was studied by means of mini-sintering test and mineralographic microscope analysis. In addition, the suitable sintering parameters such as temperature and basicity were explored. The results found that optimum temperature for the formation of calcium ferrite is 1 280℃, the basicity of 2.5-2.8 is helpful to the development of acicular or columnar calcium ferrite, and MgO content in the low silicon sintering raw materials should be lower than 2.8 % because MgO can intensively inhibit the formation of calcium ferrite. And calcium ferrite in the sinter belongs to calcium ferrite with low calcium, which is different from that in ordinary sinter at home and abroad. So, it provided theoretical basis for promoting formation of calcium ferrite in low silicon sinter and improving properties of sinter.

Experimental Study on the Characteristics of CO_2 Hydrate Formation in Porous Media below Freezing Point

Porous medium has an obvious effect on the formation of carbon dioxide hydrate. In order to study the characteristics of CO2 hydrate formation in porous medium below the freezing point, the experiment of CO2 hydrate formation was conducted in a high-pressure 1.8-L cell in the presence of porous media with a particle size of 380 μm, 500 μm and 700 μm, respectively. The test results showed that the porous medium had an important influence on the process of CO2 hydrate formation below the freezing point. Compared with porous media with a particle size of 500 μm and 700 μm, respectively, the average hydrate formation rate and gas storage capacity of carbon dioxide hydrate in the porous medium with a particle size of 380 μm attained 0.016 14 mol/h and 65.094 L/L, respectively. The results also indicated that, within a certain range of particle sizes, the smaller the particle size of porous medium was, the larger the average hydrate formation rate and the gas storage capacity of CO2 hydrate during the process of hydrate formation would be.

CHARACTERISTICS AND FORMATION CAUSES OF QINGDAO COLD WATER MASS

In this work, the main characteristics of the Qingdao Cold Water Mass were studied by using "the comparison analysis method" based on 1980 temperature,salinity and dissolved oxygen data on the western South Yellow Sea. The formation cause of the water mass was analyzed based on February of 1959 temperature and salinity data for this area and on some other authors’ studies. The results showed that the Qingdao Cold Water Mass has growing and vanishing processes: appears in the last ten days of March; has stable pattern in April; is biggest in its area in May; becomes small in its area in June; vanishes in July. It comes from the northern Shandong Coastal Water and is characterized by low temperature and salinity and high dissolved oxygen. The mass is formed under the joint effects of anticyclonic circulation and solar radiation.

Formation and Developmental Characteristics of A- and B-Type Starch Granules in Wheat Endosperm

Wheat grain natural transverse sections of 12 periods were observed and analyzed using scanning electron micrographs technology and Bio-Quant system IV image analyzer in order to detect the developing process of A- and B-type starch granules. In addition, the chemical composition and starch granule-bound proteins （SGPs） of A- and B-type starch granules were tested and analyzed. The results showed that A-type starch granules in wheat began from 3 d post anthesis （DPA） till grain maturing and B-type starch granules occured after 15 DPA till grain maturing. Approximately 98.5% of chemical compositions in both A- and B-type starch granules were amylose and amylopectin, and more than half of which were amylopectin. The amylopectin contents, average chain length, and chain length distribution （degree of polymerization〉 40） of amylopectin in A-type starch granules were significant higher than that of B-type starch granules. SGP-145, SGP-140, and SGP-26 kD were associated with A-type starch formation in wheat grain.

A catastrophic debris flow in the Wenchuan Earthquake area,July 2013：characteristics,formation,and risk reduction

In the Wenchuan Earthquake area,many co-seismic landslides formed blocking-dams in debris flow channels. This blocking and bursting of landslide dams amplifies the debris flow scale and results in severe catastrophes. The catastrophic debris flow that occurred in Qipan gully(Wenchuan,Southwest China) on July 11,2013 was caused by intense rainfall and upstream cascading bursting of landslide dams. To gain an understanding of the processes of dam bursting and subsequent debris flow scale amplification effect,we attempted to estimate the bursting debris flow peak discharges along the main gully and analyzed the scale amplification process. The results showed that the antecedent and triggering rainfalls for 11 July debris flow event were 88.0 mm and 21.6 mm,respectively. The event highlights the fact that lower rainfall intensity can trigger debris flows after the earthquake. Calculations of the debris flow peak discharge showed that the peak discharges after the dams-bursting were 1.17–1.69 times greater than the upstream peak discharge. The peak discharge at the gully outlet reached 2553 m^3/s which was amplified by 4.76 times in comparison with the initial peak discharge in the upstream. To mitigate debris flow disasters,a new drainage channel with a trapezoidal V-shaped cross section was proposed. The characteristic lengths(h1 and h2) under optimal hydraulic conditions were calculated as 4.50 m and 0.90 m,respectively.

The Mechanism of Structural Control of Ore Formation and Geochemical Characteristics in the Massive Sulfide Deposits of the Wushan Copper Ore Field,Jiangxi

The ore-controlling mechanism of the bedding fault system in the massive sulfide deposits of the Wushancopper orefield may be generalized as the control of ore deposition by optimum surface in an ore-formingstructural trap. The mechanism has three major features: (1) timing of mineralization; (2) positioning of hostformation; and (3) dependence of ore-controlling structure on properties of rocks. The 'optimum surface' is adivisional structural plane which marks obvious difference in physical, chemical and mechanical properties andis favorable for mineralization. It is also a unity of structures. lithofacies and orebodies. The structural and geochemical characteristics of the ore deposits indicate the migration trend of the ma-jor characteristic clements in the ore-controlling fault belt: elements with a small radius (Si, Fe, Mg and Al)moved towards and concentrated at the center of the belt while large-radius ones (Ca, K and Na) were remotefrom the center.

The aggregation characteristics and formation mechanism of nanoparticles in ductile shear zone

1 Introduction Nanoparticles are widely found in the ductile shear zone and it is considered to have a close relation with faulting.The sizes of these nanoparticles are generallyless than 100 nm.They have a variety of morphologies like globular structure rod-like and tubular,by the order aggregating of these nanoparticles various aggregations

Molecular Biomarker Characteristics of the Linxi Formation Source Rocks in the Middle-Western Region of Inner Mongolia:New evidence for late-stage tectonic evolution of the Paleo-Asian Ocean

Objective Two important geological issues have long been controversial in the Xing-Meng area of North China. The first concerns the final closure of Paleo-Asian Ocean in Xing-Meng area, and the other concerns the folding and lifting of the Xing-Meng Trough. The focus of thses issues is the Late Permian sedimentary environment, which is generally considered to be either an exclusively continental environment or from the closed inland sea environment in the Early to Middle stage to continental lacustrine environment in the late stage. In recent years, we have successively discovered abundant typical marine fossils （e.g., bryozoans and calcareous algae） in the Upper Permian thick limestone layer from Linxi County and Ar Horqin Banner in eastern region of Inner Mongolia and Jiutain County in Jilin Province. These significant findings have attracted the attention from fellow academics.

The Characteristics of the Hydrothermal Exhalative Dolostone of Lucaogou Formation in Santanghu basin and its Geology Setting Indication

The NW-SE trending Santanghu basin is located in Xinjiang,NW China,between Tianshan Mountains and Altai Mountains.The tectonic evolution history of north Xinjiang has long been debated,especially the question when did that area began its intraplate rift evolution stage.This abstract discusses the features and possible origin of the hydrothermal exhalative dolostone of Lucaogou Formation in Santanghu basin,aiming to provide relevant information about this question.The target dolostone are characterized by extreme thin lamina of 0.3cm–1 cm thick.Dolomite,ankerite,potassium feldspar and analcite are dominant composition.Most dolomite is poor crystallized and is in anhedral or subhedral shapes.Ankerite is generally porphyritic,few is in irregular shapes.It has to be noted that the porphyritic ankerite commonly develop zonal textures characterized by rings with various Fe O content.Potassium feldspar and analcite（<50%）are commonly observed in dolostones.Thin sections show some analcite is tetragonal trisoctahedron with harbour–like corrosion rims.Besides,few fragments of carbonatite rocks are observed in Lucaogou Formation and they perform intermittent or scattered distribution in rock layers.Previous work done by our study team showsδ13C PDB values are 4.8‰;1.4‰,6.93‰on average.Theδ18 O PDB values are between-5‰;21.1‰,-10.94‰on average.Paleosalinity calculated byδ13C andδ18 O is between 128.35 and 136.81,134.42 on average.Sr content of dolostones in study area reaches to164×10-6;37×10-6（379.1×10-6 on average）,most dolostone in target area are between 0.70457;.706194, average at 0.705360.Considering either accompanying residual tuff or residual leucite is found via electron probe,this indicates the analcite may derive form analcime phonolite.Furthermore,fragments of carbonatite rocks proves mantle-derived magmatism exist.The rapid variation ofδ18 O indicates multiple interactions of hydrothermal fluids with lake water during Lucaogou sedimentary period.87Sr/86Sr values are much lower than that of crustal silica rocks while are more close to mantle derived rocks,which indicates diagenetic hydrothermal fluid is mantle-origin.It has been reported that dolostone does not intergrow with iron-rich dolostone in study area.According to the latest X diffraction results of cores,iron-rich dolostone distributes rather locally.Given that ankerite commonly develop zonal textures characterized by various Fe O content,we confirm it is due to multiple hydrothermal fluids activities in different hydrothermal vents.There should be abundant hydrothermal vents during Lucaogou period.Deep faults and its relevant fractures built plenty paths for mantle-origin hydrothermal fluids to run up.Different vents owned various fluid properties,so did relevant sedimentation products.Hence we inclined to believe Santanghu basin was at intraplate rift evolution stage,under regional extension condition in late Carboniferous.During early-mid Permian the basin was a starved,deep lacustrine intracontinental rift basin.Accordingly,in northern Xinjiang,ocean basin may close in late Carboniferous and started continental sedimentary development in early Permian.

Characteristics and Formation Mechanism of the Geothermal Field in the North China Downfaulted Basin

The geothermal field is mainly controlled by the regional tectonic framework characterized by alternationsof uplifted and depressed basement. and exhibits a similar zoned distribution of temperatures. In the upliftedarea the geothermal gradient （G） and terrestrial heat flow value（q） of the Cenozoic sedimentary cover are rela-tively high, with G=3.5-5.0℃/100m and q=63-84mW/m;; whereas in the depressions they are rela-tively low, with G=2.7-3.5℃/100m and q=46-59mW/m;. In the whole region, G=3.58℃/100m and q=61.5±13.4nW/m;, indicating a comparatively high geothermal background and the presence of localgeothermal anomalies. A comparison of the results of mathematical simulation of the geothermal field with themeasured values shows a good agrecment between them. The geothermal difference between various tectonicunits is caused chiefly by the lateral and vertical variation of thermal properties of shallow crustal rocks. Thisphenomenon can be regarded as the result of redistribution of relatively uniform heat flows from the deep crustin the surficial part of the crust in the process of their upward conduction.

Microstructure characteristics of Ni/WC composite cladding coatings

A multilayer tungsten carbide particle（WCp）-reinforced Ni-based alloy coating was fabricated on a steel substrate using vacuum cladding technology.The morphology,microstructure,and formation mechanism of the coating were studied and discussed in different zones.The microstructure morphology and phase composition were investigated by scanning electron microscopy,optical microscopy,X-ray diffraction,and energy-dispersive X-ray spectroscopy.In the results,the coating presents a dense and homogeneous microstructure with few pores and is free from cracks.The whole coating shows a multilayer structure,including composite,transition,fusion,and diffusion-affected layers.Metallurgical bonding was achieved between the coating and substrate because of the formation of the fusion and diffusion-affected layers.The Ni-based alloy is mainly composed of y-Ni solid solution with finely dispersed Cr7C3/Cr（23）C6,CrB,and Ni＋Ni3Si.WC particles in the composite layer distribute evenly in areas among initial Ni-based alloying particles,forming a special three-dimensional reticular microstructure.The macrohardness of the coating is HRC 55,which is remarkably improved compared to that of the substrate.The microhardness increases gradually from the substrate to the composite zone,whereas the microhardness remains almost unchanged in the transition and composite zones.

Improved Methods for Acoustic Transmission along the Drill String and Other Periodic Media

Acoustic telemetry along the drill string helps to know the physical and chemical characteristics of the formation and drilling fluid.A time-domain algorithm is developed for the propagation of one-dimensional axial stress waves with the inner and outer viscous fluid.The algorithm simulates the passbands,stopbands and spikes due to the presence of the discontinuous boundaries of drill string.Then the effects of transmitted pulses and transceivers on acoustic transmission are analysed.The simulated results show that the raised cosine pulses and optimal placements of transceivers improve system performance.Moreover,dual PZT receivers can exclude signals propagating in a direction opposite to the transmitted signals. It is obvious that the uses of the available modeling and signal processing techniques can make the drill string as a waveguide for transmitting information at high data rates.

A Review of the Research on English Pronunciation Self-concept

English pronunciation self-concept is a personal judgment based on pronunciation.It is English learners’self-perception as well as the judgment of their English pronunciation competence as well as pronunciation learning ability,which is formed as they develop their skills in pronunciation.A higher level of English pronunciation self-concept can promote students’self-assurance in foreign language learning.Through the analysis,this paper summarizes the scholars’studies about English pronunciation self-concept as follows:1)Formation and characteristics of English pronunciation self-concept;2)Relevance between English pronunciation self-concept as well as English learning.

Characteristics and formation mechanism of regional haze episodes in the Pearl River Delta of China

To investigate the characteristics and the specific mechanism of continuous haze,comprehensive measurements were conducted from 15 October to 19 November in the Atmospheric Environment Monitoring Super-Station in Heshan of Guangdong province.Five haze episodes occurred in October and November 2014 in the Pearl River Delta（PRD）region. The meteorological parameters, gas data, chemical compositions, and optical parameters of the aerosols were obtained. Among these events, the second haze episode,with the highest concentration of PM2.5 of 187.51 μg/m^3, was the most severe. NO^3-was always higher than SO_4^（2-）, which indicated that motor vehicles played an important role in the haze, even though the oxidation rate from SO_2 to SO_4^（2-）was faster than that of NOXto NO_3^-. The difference between the hourly averages of Na＋and K＋during the haze episode and clean days was small, implying that straw combustion and sea salt had no significant effect on the occurrence of haze, and the backward trajectories of the air masses also conformed with this result. The air pollutants were difficult to disperse because of the significant decrease in the planetary boundary layer（PBL） height. Relative humidity played a crucial role in the formation of haze by leading to hygroscopic growth of the diameter of aerosols.

Case History of the Disastrous Debris Flows of Tianmo Watershed in Bomi County, Tibet, China: Some Mitigation Suggestions

Debris flows and landslides, extensively developing and frequently occurring along Parlung Zangbo, seriously damage the Highway from Sichuan to Tiebt(G318) at Bomi County. The disastrous debris flows of the Tianmo Watershed on Sept. 4, 2007, July 25, 2010 and Sept. 4, 2010, blocked Parlung Zangbo River and produced dammed lakes, whose outburst flow made 50 m high terrace collapse at the opposite bank due to intense scouring on the foot of the terrace. As a result, the traffic was interrupted for 16 days in 2010 because that 900 m highway base was destructed and 430 m ruined. These debris flows were initiated by the glacial melting which was induced by continuous higher temperature and the following intensive rainfall, and expanded by moraines along channels and then blocked Parlung Zangbo. At the outlet of watershed,the density, velocity and peak discharge of debris flow was 2.06 t/m3, 12.7 m/s and 3334 m3/s, respectively. When the discharge at the outlet and the deposition volume into river exceeds 2125 m3/s and 126×103 m3, respectively, debris flow will completely blocked Parlung Zangbo. Moreover,if the shear stress of river flow on the foot of terrace and the inclination angel of terrace overruns 0. 377 N/m2 and 26°, respectively, the unconsolidated terrace will be eroded by outburst flow and collapse. It was strongly recommended for mitigation that identify and evade disastrous debris flows, reduce the junction angel of channels between river and watershed, build protecting wall for highway base and keep appropriate distance between highway and the edge of unconsolidated terrace.

Investigation of Different Coke Samples Adhering to Cyclone Walls of a Commercial RFCC Reactor

The microstructure and properties of the coke samples collected from 4 different wall regions of the cyclone in the reactor of a residue fluid catalytic cracking unit(RFCCU) were analyzed by using the scanning-electron microscope(SEM), and the possible coke formation processes were investigated as well. The results showed that some of the heavy nonvolatile oil droplets entrained in the flowing oil and gas mixture could possibly deposit or collide on the walls by gravity settling or turbulence diffusion, and then were gradually carbonized into solid coke by condensing and polymerization along with dehydrogenation. Meanwhile some of fine catalyst particles also built up and integrated into the solid coke. The coke can be classified into two types, namely, the hard coke and the soft coke, according to its property, composition and microstructure. The soft coke is formed in the oil and gas mixture's stagnant region where the oil droplets and catalyst particles are freely settled on the wall. The soft coke appears to be loose and contains lots of large catalyst particles. However, the hard coke is formed in the oil and gas mixture's flowing region where the oil droplets and catalyst particles diffuse towards the wall. This kind of coke is nonporous and very hard, which contains a few fine catalyst particles. Therefore, it is clear that the oil and gas mixture not only carries the oil droplets and catalyst particles, but also has the effects on their deposition on the wall, which can influence the composition and characteristics of deposited coke.

FORMATION MECHANISM AND PROPAGATION CHARACTERISTICS OF THE EQUATORIAL THERMALLY-FORCED SHORT-TERM CLIMATIC OSCILLATION DURING THE NORTHERN SUMMER

In this study, in order to investigate the global climatic oscillations forced by sea surface temperature (SST) anomalies over equatorial central-eastern Pacific, two numerical schemes with different SST distri-butions (normal and anomalous cases) are tested by using a nine-layer global spectral model. Experiment results show that (i) in northern summer, a wave train that is similar to the teleconnection pattern suggested by Nitta (1987) and Huang (1987) in the Northern Hemisphere and another one in the Southern Hemisphere are reproduced; (ii) simulated results suggest that the response of atmosphere in middle-high latitudes of both hemispheres to an anomalous heating source is more sensitive in tropical western Pacific than in equatorial central-eastern Pacific; and (iii) in northern summer, the formation of low-frequency oscillations on monthly (seasonal) time scale results from energy dispersion as well as interactions between eddies and zonal flow; and between eddies.