Damage of a large-scale reinforced concrete wall caused by an explosively formed projectile(EFP)

To quickly break through a reinforced concrete wall and meet the damage range requirements of rescuers entering the building,the combined damage characteristics of the reinforced concrete wall caused by EFP penetration and explosion shock wave were studied.Based on LS-DYNA finite element software and RHT model with modified parameters,a 3D large-scale numerical model was established for simulation analysis,and the rationality of the material model parameters and numerical simulation algorithm were verified.On this basis,the combined damage effect of EFP penetration and explosion shock wave on reinforced concrete wall was studied,the effect of steel bars on the penetration of EFP was highlighted,and the effect of impact positions on the damage of the reinforced concrete wall was also examined.The results reveal that the designed shaped charge can form a crater with a large diameter and high depth on the reinforced concrete wall.The average crater diameter is greater than 67 cm(5.58 times of charge diameter),and crater depth is greater than 22 cm(1.83 times of charge diameter).The failure of the reinforced concrete wall is mainly caused by EFP penetration.When only EFP penetration is considered,the average diameter and depth of the crater are 54.0 cm(4.50 times of charge diameter)and 23.7 cm(1.98 times of charge diameter),respectively.The effect of explosion shock wave on crater depth is not significant,resulting in a slight increase in crater depth.The average crater depth is 24.5 cm(2.04 times of charge diameter)when the explosion shock wave is considered.The effect of explosion shock wave on the crater diameter is obvious,which can aggravate the damage range of the crater,and the effect gradually decreases with the increase of standoff distance.Compared with the results for a plain concrete wall,the crater diameter and crater depth of the reinforced concrete wall are reduced by 5.94%and 9.96%,respectively.Compared to the case in which the steel bar is not hit,when the EFP hit one steel bar and the intersection of two steel bars,the crater diameter decreases by 1.36%and 5.45%respectively,the crater depth decreases by 4.92%and 14.02%respectively.The EFP will be split by steel bar during the penetration process,resulting in an irregular trajectory.

Mechanism investigation and strategies for reducing residual stress at open ends of the roll-formed part

Increasing geometrical accuracy at open ends of the roll-formed part is difficult due to the release of residual stress after end cutting.In this work,a typical rail with a high requirement of geometry accuracy was selected to realize the behaviors of residual stress release.First,residual stress distribution after roll forming is discussed in detail by finite element analysis with ABAQUS.In addition,two different approaches are proposed to check their capabilities in reducing the residual stress level.The results indicate that both additional rolling passes and multiple bending processes are beneficial to reducing uniform residual stress.

Comparative study of model tests on automatically formed roadway and gob-side entry driving in deep coal mines

Automatically formed roadway(AFR)by roof cutting with bolt grouting(RCBG)is a new deep coal mining technology.By using this technology,the broken roadway roof is strengthened,and roof cutting is applied to cut off stress transfer between the roadway and gob to ensure the collapse of the overlying strata.The roadway is automatically formed owing to the broken expansion characteristics of the collapsed strata and mining pressure.Taking the Suncun Coal Mine as the engineering background,the control effect of this new technology on roadways was studied.To compare the law of stress evolution and the surrounding rock control mechanisms between AFR and traditional gob-side entry driving,a comparative study of geomechanical model tests on the above methods was carried out.The results showed that the new technology of AFR by RCBG effectively reduced the stress concentration of the roadway compared with gob-side entry driving.The side abutment pressure peak of the solid coal side was reduced by 24.3%,which showed an obvious pressure-releasing effect.Moreover,the position of the side abutment pressure peak was far from the solid coal side,making it more beneficial for roadway stability.The deformation of AFR surrounding rock was also smaller than the deformation of the gob-side entry driving by the overload test.The former was more beneficial for roadway stability than the latter under higher stress conditions.Field application tests showed that the new technology can effectively control roadway deformation.Moreover,the technology reduced roadway excavation and avoided resource waste caused by reserved coal pillars.

Dehydrogenation characteristics of LiAlH4 improved by in-situ formed catalysts

The hydrogen storage properties and catalytic mechanism of FeCl-doped LiAlHwere investigated in minute details. LiAlH-2 mol% FeClsamples start to release hydrogen at 76 °C, which is 64 °C lower than that of as-received LiAlH. Isothermal desorption measurements show that the 2 mol% FeCl-doped sample releases 7.0 wt% of hydrogen within 17 min at 250 °C. At lower temperatures of 110 °C and 80 °C, the sample can release 4.4 wt% and 3 wt% of hydrogen, respectively. The apparent activation energy of LiAlH-2 mol% FeClsamples for R2 is 105.02 k J/mol, which is 67 k J/mol lower than that of pure LiAlH. The reaction between LiAlHand FeClduring ball milling was found by analyzing the X-ray diffraction results,and Fe-Al particles formed in-situ from the reaction act as the real catalyst for the dehydrogenation of LiAlH.

Mssbauer Spectroscopic Studies on a Supersaturated Solid Solution of Fe-Cu Formed by Mechanical Alloying

Mechanical alloying (MA) was employed to produce supersaturated solid solutions of Fe1-xCux,which is virtually immiscible under an equilibrium condition at ambjent temperature. The X-ray diffraction results show that the solutions formed in the concentration ranges of x≤0.1 5 and x≥0.40 are of bcc structure of iron and fcc structure of copper. respectively. For the region in between.however, the alloy obtained is a mixture of bcc plus fcc phases. The Mossbauer spectrum of the solid solution of a single phase could be fitted by two sub-spectra with hyperfine magnetic fields of 200 and 250 kOe. respectively. suggesting that there must exist two forms of coordination in the solution. While to fit the spectrum for the solution with mixed structu re. three Sub-spectra. including a spectrum of α-Fe, should be used. The variation of the Mossbauer spectra of Fe60Cu40 with milling time as well as annealing temperature was systematically studied. This may be ascribed to the changes of the number of nearest neighboring atoms of iron in the processes of formation and decomposition of the solid solution during milling and annealing

Forming Mechanism of Gaseous Defect in Ti-48Al-2Cr-2Nb Exhaust Valves Formed with Permanent Mold Centrifugal Casting Method

A method combining theoretical analysis with experiment is adopted and the flowing process of Ti-48A1-2Cr-2Nb alloy melt poured in a permanent mould during the centrifugal casting process has been analyzed. A mathematical model of the filling process is established and the forming mechanism of internal gaseous defect is summarized. The results of calculation show that the melt fills the mould with varying cross-section area and inclined angle. The filling speed of the cross-section is a function of filling time. The cross-section area is directly proportional to the filling speed and the inclined angle is inversely proportional to the filling speed at a given rotating speed of the platform. Both of them changes more obvious near the mould entrance. The gaseous defect can be formed in several ways and the centrifugal field has an important influence on the formation of the defect. In addition, the filling process in centrifugal field has been verified by wax experiments and the theoretical analysis are consistent with experimental results.

CH_3NH_3 Formed by Electron Injection at Heterojunction Inducing Peculiar Properties of CH_3NH_3PbI_3 Material

The effect of formed CH_3NH_3 at the heterojunction on properties of CH_3NH_3PbI_3 material is investigated based on experiment and theoretical calculation. Our calculation results show that the giant dielectric constant, anomalous hysteresis and long-lasting polarization for CH_3NH_3PbI_3 originate from the formed CH_3NH_3 at the heterojunction. It is found that the induced weak EPS by the reorientation of CH_3NH_3 sub-group along the built-in electric field enables us to effectively increase the ordering of entire lead-halide framework. In addition, the heterojunction has an advantage of channel separation between carrier transport and electron diffusion. These properties of the heterojunction are the main origin of the high efficiency of CH_3NH_3PbI_3 solar cells.

Nanomechanical Properties of Amyloid Fibrils Formed in a Water Nanofilm on Mica Surface

The assessment of nanomechanical properties of a single amyloid fibril in a confined space provides important information for understanding the role of fibrils in a cell microenvironment. In this study, the structure and nanomechanical properties of different fibrils formed in water nanofilms on mica surface are carefully investigated by using the new atomic force microscopy imaging mode-peak force quantitative nanomechanics （PF-QNM）. We find that two types of fibrils with different morphologies are formed in water nanofilm on mica. The compression elasticities of these two types of fibrils are 3.9±0.9 and 2.5±0.6 GPa, respectively. The remarkable difference is possibly due to the structural discrepancy in two types of fibrils.

NUMERICAL SIMULATION FOR FORMED PROJECTILE OF DEPLETED URANIUM ALLOY

The numerical simulation for forming projectile of depleted uranium alloy with the SPH (Smooth Particle Hydrodynamic) algorithm was presented. In the computations the artificial pressures of detonation were used, i.e., the spatial distribution and time distribution were given artificially. To describe the deformed behaviors of the depleted uranium alloy under high pressure and high strain rate, the Johnson_Cook model of materials was introduced. From the numerical simulation the formed projectile velocity, projectile geometry and the minimum of the height of detonation are obtained.

A STUDY ON THE STRUCTURE AND PROPERTIES OF POLYBUTYLALDEHYDE FORMED IN LOW TEMPERATURE PLASMA

The polybutylaldehyde obtained by plasma polymerization was investigated by means of IR, X-ray diffraction, GC-MS, elementary analysis, TEM, electron diffraction and contact angle measurements etc. The results showed that the polymer formed in plasma is amorphous crosslinked polymer, and its backbone is made of carbon atoms. The surface energy of the polymer film is independent of the polymerization conditions. No addition reaction has taken place in the carbonyl group of butylaldehyde in the plasma condition. The result of the wettability measurements showed that the polymer film is generally hydrophobic and the surface energy of the film is about 41 dyn/cm, in which the dispersion force contribution is the majority. The electron diffraction proved that some crystal substance, even the single crystals were present in the polymer. X-ray diffraction also proved the presence of crystal and showed about 15% crystaUinity fraction.

Oxidation Resistance of the Aluminide Coating Formed on Carbon Steels

Low and medium carbon steels were aluminized by the pack aluminizing technique using halideactivated pure-Al and Fe-Al packs. The effect of mixture composition, aluminizing temperatureand time and C content of the steel substrate on the structure and thickness of the aluminidelayer, and on the oxidation resistance was investigated. The optimum oxidation resistance canbe achieved with a low carbon steel substrate when the intermetallic phases Fe3Al and FeAlform the surface of the aluminide layer. In this case, the Al concentration at the surface of thealuminide coating is at least ≥15 wt pct. Formation of high Al concentration phases (FeAl3 andFe2Al5) during aluminizing should be avoided as they tend to embrittle the aluminide layer andreduce its oxidation resistance.

Non-equilibrium Thermodynamic Analysis of The Transport Properties of Formed-in-Place Zirconium (Ⅳ) Hydrous Oxide-Polyacylate Membranes in aqueous NaNO_3 solution

Nanofiltration of aqueous NaNO3 solution with a dynamically formed Zr(IV) hydrousoxide-PAA membrane is presented. The practical transpoft coefficients Lp, σ, ω were obtainedusing relationships of the non-equilibrium thermodynamics and were used to calculate thefrictional coefficients of a friction model.

Double⁃Shear Experiments of Cold⁃Formed Steel Stud⁃to⁃Sheathing Connections at Elevated Temperatures

The behavior of cold⁃formed steel(CFS)stud⁃to⁃sheathing connections at elevated temperatures is an important parameter for the fire resistance design and modeling of mid⁃rise CFS structures.In this paper,three kinds of sheathings,namely,medium⁃and low⁃density calcium⁃silicate boards and oriented strand board,were selected for double⁃shear experiments on the mechanical properties of 253 screw connections at ambient and elevated temperatures.The effects of the shear direction,screw edge distance and the number of screws on the behavior of the connections were studied.The results showed that the shear direction and the screw edge distance more significantly influenced the peak deformation,while their impacts on the peak load varied with the type of sheathings.Compared with the single⁃screw connections,the peak loads of the specimens with double⁃screw connections obviously increased but did not double.Finally,a simplified load⁃displacement curve model of stud⁃to⁃sheathing connections at elevated temperature was generated first by establishing the prediction formula for characteristic parameters,such as the peak load,the peak deformation and the elastic stiffness,and then by considering whether the curves corresponded to stiffness increase phenomena.The present investigation provides basic data for future studies on the numerical modeling of CFS structures under fire conditions.

TEMPERING RESPONSE OF A DEFORMED LOW CARBON DUAL PHASE STRUCTURE

The low carbon dual phase structure was cold de formed first,then was tempered at 200 to 600℃.The variation in strength and ductility during tempering of the steel was investigated.It was found that a fter the de formed dual phase structure was tempered at 200 to 600℃, with the increase in the tempering temperature the tensile strength decreases rapidly;the lotal elongation remains constant at 200 to 500℃ but began to rise dramatically at a critical temperature between 500 and 600℃.However,when the non-deformed dual phase structure was tempered at the same temperature range,the tensile strength decreases and the total elongation increases continuously with the increase of temperature.It was demonstrated from TEM analysis that precipitating carbides density along the boundaries ofmartensite lath and the recrystallized grains are responsible for the tempering response ofthe de formed dual phase structure.

100 Million Ton Oil and Gas FieldWill Be Formed in Liaohe

UptothebeginningofOctober,15milliontonsofnewlyaddedprovenreserveshadbeenfoundinYuedongareabyLiaoheOffshoreOilExplorationandDevelopmentCompany.Oilandgasfieldswithascaleofapproximately100milliontonswillbeformedontheentireHainanstructuralbeltbytheendoft...

Microstructure evolution and phase transformation of traditional cast and spray-formed hypereutectic aluminium-silicon alloys induced by heat treatment

Microstructural evolution and phase transformation induced by different heat treatments of the hypereutectic aluminium-silicon alloy, Al-25Si-5Fe-3Cu （wt%, signed as 3C）, fabricated by traditional cast （TC） and spray forming （SF） processes, were investigated by differential scanning calorimetry （DSC） and scanning electron microscopy （SEM） combined with energy dispersive X-ray spectroscopy and X-ray diffraction techniques. The results show that A17Cu2Fe phase can be formed and transformed in TC- and SF-3C alloys between 802-813 K and 800-815 K, respectively. The transformation from β-Al5FeSi to δ-Al4FeSi2 phase via peritectic reaction can occur at around 858-870 K and 876-890 K in TC- and SF-3C alloys, respectively. The starting precipitation temperature of δ-Al4FeSi2 phase as the dominant Fe-bearing phase in the TC-3C alloy is 997 K and the exothermic peak about the peritectic transformation of δ-Al4FeSi2→β-Al5FeSi is not detected in the present DSC experiments. Also, the mechanisms of the microstructural evolution and phase transformation are discussed.

MICROSTRUCTURAL CHARACTERISTICS AND MECHANICAL PROPERTIES OF SPRAY FORMED HIGH SPEED STEEL FOR WORK ROLL

The mechanical properties and microstructure characteristics of a high speed steel (HSS) for roll has been studied. As compared with the as-cast HSS, the spray-formed HSS have fine grain and segregation free microstructures. Carbides distribute uniformly. The morphology and types of the carbides in spray-formed HSS are different from those in as-cast HSS. The results of the high temperature tensile experiment show that, as to spray-formed HSS, there is a possibility of superplastic deformation in the range of 780-810℃.

Effect of Intermediate Heat Treatment Temperature on Microstructure and Notch Sensitivity of Laser Solid Formed Inconel 718 Superalloy

Inconel 718 superalloys deposited by laser solid forming （LSF） were heat treated with solution treatment,intermediate heat treatment （IHT） and two-stage aging treatment in sequence （SITA heat treatment）.The effect of IHT temperature on microstructure,tensile property and notch sensitivity of LSFed Inconel 718 superalloy at 500 ℃ were investigated.As-deposited columnar grains have transformed to equiaxed grains and the grains were refined due to the recrystallization during the SITA heat treatment.It is found that the size and amount of δ phase dispersed at grain boundaries decreased with the increasing of IHT temperature,and δ phase disappeared when the IHT temperature reached 1 020 ℃.The ultimate tensile strength （UTS） and yield strength （YS） of smooth samples increased to a maximum when the IHT temperature reached 980 ℃ and then decreased slightly to a minimum when the IHT temperature was 1 000 ℃,and followed by slight increasing again till the IHT temperature reached 1 020 ℃,resulted from the competition of precipitation strengthening effect of γ″ and γ＇ phase and the grain boundary weakening effect caused by the gradual disappearance of δ phase with increasing the IHT temperature.The notch sensitivity factor （qe） decreased but still greater than 1 as the IHT temperature increased,which is attributed to the decrease of the size and amount of δ precipitation.