The Evaluation of the Sound Insulation of Partition in Expanded Frequency Range

This paper reports on an evaluation of airborne sound insulation in a wider frequency range then is used in classical measurements. For analyzing sound insulation was used frequency range from 50 Hz to 10 kHz via standard range I00 Hz to 3,15 kHz. For four constructions with different structure was measured sound reduction index depend on frequency and calculated Weighted sound reduction index according to EN ISO 717-1. Then the results were compared. The measurements were made for samples of construction with different sizes. The results of measurements show how the size of sample influence on measured sound insulation. This article could be useful for specialist of architect acoustic and all who interest in sound insulation.

Propagation characteristics of the Pc3 frequency range pulsations in the cusp latitudes

Two induction magnetometers have been installed at Zhongshan Station and Davis Station, Antarctica respectively. We adopt with cross-spectral analysis technique to analyze the data of the two induction magnetometers, in June, September,December 1996 and March 1997. to investigate the Pc3 frequency range pulsation occurrence and propagation characteristics in the cusp latitudes. The results are summarized as following:At Zhongshan-Davis Stations, the Pc3 frequency range pulsations occur mainly around the local noon/ local magnetic noon and local magnetic midnight respectively. In daytime, the pulsations have a seasonal variation in amplitude, occurrence and temporal range, all of them are sma1lest in winter. But in nighttime, the pulsations have no such a variation. The pu1sation amplitude in nighttime is much larger than the one in daytime all oveI the year. The pulsation propagating direction is mainly western in daytime and irregularly in nighttime. It can be thought that the different sources of the pulsation and the ionospheric electric conductivity are mainly responsible for these characteristics.

Design of scale model of plate-shaped absorber in a wide frequency range

In order to design the scale model in a wide frequency range,a method based on the reflective loss is proposed according to the high-frequency approximation algorithm,and an example of designing the scale model of a plate-shaped absorber is given in this paper.In the example,the frequency of the full-size measurement ranges from 2.0 GHz to 2.4 GHz,the thickness of the full-size absorber is 1 mm and the scale ratio is 1/5.A two-layer scale absorber is obtained by the proposed method.The thickness values of the bottom and top layer are 0.4 mm and 0.5 mm,respectively.Furthermore,the scattering properties of a plate model and an SLICY model are studied by FEKO to verify the effectiveness of the designed scale absorber.Compared with the corresponding values from the theoretical scale model,the average values of the absolute deviations in 10 GHz～12 GHz are 0.53 d Bm^2,0.65 d Bm^2,0.76 d Bm^2 for the plate model and 0.20 d Bm^2,0.95 d Bm^2,0.77 d Bm^2 for the SLICY model while the incident angles are 0°,30°,and 60°,respectively.These deviations fall within the Radar cross section（RCS） measurement tolerance.Thus,the work in this paper has important theoretical and practical significance.

Design and optimization of an ultra-wide frequency range CMOS divide-by-two circuit

A novel toggled flip-flop（TFF） divide-by-two circuit（DTC） and its optimization method based on a large-signal analysis approach are proposed.By reducing the output RC constant in tracking mode and making it large in latching mode,compressing the internal signal swing as well as compensating the current leaked in the latching mode, the operating frequency range is greatly expanded.Implemented in a SMIC 0.13μm RF CMOS process with a 1.2 V power supply,it can work under an ultra-wide frequency band ranging from 320 MHz to 29.6 GHz.Experimental results show that two phase-locked loops（PLLs） with the proposed DTC can achieve in-band phase noise of-94 dBc/Hz @ 10 kHz under 4224 MHz operating frequency and-84 dBc/Hz @ 10 kHz under 10 GHz operating frequency,respectively. The power consumption of the proposed DTC is reduced by almost 50%compared with the conventional counterparts.

Algorithm for the layout of a piezoelectric element in an elastic medium providing the maximal piezoelectric effect within a specified frequency range

An algorithm for the layout of a piezoelectric that provides the most efficient performance within a specified range of vibration frequencies is proposed in this paper.This algorithm is based on the consideration of a special parameter within the area of a piezoelectric element’s possible location.This parameter characterizes the superposition of electromechanical coupling coefficients’for all the natural vibration frequencies included in a specified frequency range.The condition for defining the best option for location of the piezoelectric element in the case of several equivalent positions is specified.The efficiency of the proposed algorithm is shown numerically.The electromechanical coupling coefficients were calculated numerically based on solution to the problem of natural vibrations for electroelastic bodies using a finite element method.The calculations were performed to define the best location for a single piezoelectric element at the surface of a thin-walled shell having a half-cylindrical shape.The results are presented for natural vibration frequencies within the frequency range from 0 up to 1100 Hz.The numerical results were obtained by solving the problem of natural vibrations with a finite element method using the ANSYS software package.

Theoretical analysis of ion cyclotron range of frequency antenna array for HT-7U

This paper considers the coupling analysis of phased antenna array designed to excite fast wave in the ion cyclotron range of frequency. The coupling of the antenna is calculated in slab geometry. The coupling code based on the variational principle gives the self-consistent current flowing in the antenna, this method has been extended so that it can be applied to a phased antenna array. As an example, this paper analyses the coupling prosperities of a 2 × 2 phased antenna array. It gives the optimum geometry of antenna array. The fields excited at plasma surface are found to more or less correspond to the antenna current phasing.

The equilibrium range of wind wave frequency spectrum

-Theoretical form of equilibrium range is given on the basis of the wind wave frequency spectra proposed by Wenel al. (1988a,b,c, 1989a,b). The effects of peakness factor and water depth are discussed. In the case of deep water the e-quilibrium range is reduced to the form first proposed by Toba (1973) and the coefficient of the formula is shown to be the function of nondimensional fetch or peak frequency. Results of the present paper have been verified through field data.

Frequency response range of terahertz pulse coherent detection based on THz-induced time-resolved luminescence quenching

It has been proposed previously that the coherent detection of a terahertz（THz） pulse can be achieved based on the time-resolved luminescence quenching. In this paper, we investigate the frequency response range of this novel detection technology by simulating the motion of carriers in gallium arsenide（GaAs） by the ensemble Monte Carlo method. At room temperature, for a direct-current（DC） voltage of 20 kV/cm applied to the semiconductor（GaAs） and sampling time o140 fs, the luminescence quenching phenomena induced by terahertz pulses with different center frequencies are studied The results show that the quenching efficiency is independent of the THz frequency when the frequency is in a range o0.1 THz–4 THz. However, when the frequency exceeds 4 THz, the efficiency decreases with the increase of frequency Therefore, the frequency response range is 0.1 THz–4 THz. Moreover, when the sampling time is changed to 100 fs the frequency response range is extended to be approximately 0.1 THz–5.6 THz. This study of the frequency-dependen characteristics of the luminescence response to the THz pulse can provide a theoretical basis for the exploration of THz detection technology.

Simulation of ion cyclotron wave heating in the EXL-50U spherical tokamak based on dispersion relations

This study investigates the single-pass absorption(SPA) of ion cyclotron range of frequency(ICRF) heating in hydrogen plasma of the EXL-50U spherical tokamak,which is an upgraded EXL-50 device with a central solenoid and a stronger magnetic field.The reliability of the kinetic dispersion equation is confirmed by the one-dimensional full-wave code,and the applicability of Porkolab's simplified theoretical SPA model is discussed based on the kinetic dispersion equation.Simulations are conducted to investigate the heating effects of the fundamental and second harmonic frequencies.The results indicate that with the design parameters of the EXL-50U device,the SPA for second harmonic heating is 63%,while the SPA for fundamental heating is 13%.Additionally,the optimal injection frequencies are 23 MHz at 0.9 T and 31 MHz at 1.2 T.The wave vector of the antenna parallel to the magnetic field,with a value of k_‖=7.5 m^(-1),falls within the optimal heating region.Simulations reveal that the ICRF heating system can play an important role in the ion heating of the EXL-50U.

ANALYSIS AND MEASUREMENT OF LARGE DYNAMIC RANGE RF SWITCH INTER-MODULATION

Radio Frequency (RF) switch circuit is the basic part of microwave devices and systems. The non-linearity distortion figure is necessary in the field of large dynamic range of signal. This letter analyzes the basic switch circuit and its inter-modulation, and studies in detail the measurement methods and systems of RF switch intercept point. It has provided cascaded simulation testing methods, which can accurately measure the PF switch, of which the second or third order intercept point value is above 75dB and 60dB, respectively. As the testing results are consistent with the theoretical analyses, it proves that the validity of the method satisfies the requirements of large scaled linearity measurement in engineering.

A wide range sigma-delta fractional-N frequency synthesizer with adaptive frequency calibration

A wide range fractional-N frequency synthesizer in 0.18μm RF CMOS technology is implemented. A switched-capacitors bank LC-tank VCO and an adaptive frequency calibration technique are used to expand the frequency range.A 16-bit third-order sigma-delta modulator with dither is used to randomize the fractional spur. The active area is 0.6 mm;.The experimental results show the proposed frequency synthesizer consumes 4.3 raA from a single 1.8 V supply voltage except for buffers.The frequency range is 1.44-2.11 GHz and the frequency resolution is less than 0.4 kHz.The phase noise is -94 dBc/Hz @ 100 kHz and -121 dBc/Hz @ 1 MHz at the output of the prescaler with a loop bandwidth of approximately 120 kHz.The performance meets the requirements for the multi-band and multi-mode transceiver applications.

Photonic-assisted approach for instantaneous microwave frequency measurement with tunable range by using Mach-Zehnder interferometers

A novel photonic-assisted approach to microwave frequency measurement is proposed and experimentally demonstrated. The proposed scheme is based on the frequency-to-power mapping with different transmis- sion responses. A polarizer is used in one output branch of a phase modulator to simultaneously implement phase modulation and intensity modulation. Owing to the complementary nature of the transmission re- sponses and the Mach-Zehnder interferometers （MZIs）, this scheme theoretically provides high resolution and tunable measurement range. The measurement errors in the experimental results can be kept within 0.2 GHz over a freauencv ranee from 0.1 to 5.3 GHz.

Low Phase Noise VCO using Novel Harmonic Control Circuit Based on Quad-band Composite Right/Left-handed Transmission Line

In this paper, a novel Voltage-Controlled Oscillator （VCO） using the harmonic control circuit based on the quad-band Composite Right/Left-Handed （CRLH） Transmission Line （TL） is presented to reduce the phase noise without the reduction of the frequeacy tuning range and miniaturizing the circuit size. The phase noise has been reduced by the quad-band harmonic control circuit which has the short impedance for the second- and third- and fourth- and fifth-hannonic components. The CRLH TL with two Left-Handed （LH） （backward） and two Right-Handed （RH） （forward） pass bands are used to design the quad-band harmonic control circuit. The high- Q resonator has been used to reduce the phase noise, but it has the problem of the frequency timing range reduction. However, the frequency tuning range of the proposed VCO has not reduced because the phase noise has reduced without the high-Q resonator. The miniaturization of the circuit size is achieved by using the quad-band CRLH TL instead of the conventional RH TL, The phase noise of VCO is - 124.43～ - 122.67 dBc/Hz at 100 kHz in the tuning range of 5. 729 ～5.934 GHz.

SIMULATION STUDY ON AIRBORNE SAR ECHO SIGNAL

Through analyzing the influence on echo signal by factors of kinematical parameters of airborne SAR platform and radar antenna direction, this letter, on the basis of classical SAR echo signal analogue algorithm, puts forward certain airborne SAR echo signal analogue algorithm of distance directional frequency domain pulse coherent accumulation, and goes through simulation. The simulation results have proved the effectiveness of this algorithm.

Current Ramp-up by Microwave Power in the LATE Device

In the low aspect ratio torus experiment （LATE） device, plasma current is initiated and ramped up to 20 kA solely by microwave power at the electron cyclotron （EC） range of frequency with a ramp of the external vertical field By for the radial equilibrium of plasma torus at larger currents. Measurements suggest that an energetic electron tail in the energy range of about 200 keV carries the current. The line averaged electron density is higher than the plasma cutoff density, suggesting that tail electrons might be driven by electron Bernstein waves modeconverted from the launched electromagnetic waves.

An Improved Modulation Strategy for Single-phase Three-level Neutral-point-clamped Converter in Critical Conduction Mode

Two-level totem-pole power factor correction(PFC)converters in critical conduction mode(CRM)suffer from the wide regulation range of switching frequency.Besides,in highfrequency applications,the number of switching times increases,resulting in significant switching losses.To solve these issues,this paper proposes an improved modulation strategy for the single-phase three-level neutral-point-clamped(NPC)converter in CRM with PFC.By optimizing the discharging strategy and switching state sequence,the switching frequency and its variation range have been efficiently reduced.The detailed performance analysis is also presented regarding the switching frequency,the average switching times,and the effect of voltage gain.A 2 k W prototype is built to verify the effectiveness of the proposed modulation strategy and analysis results.Compared with the totem-pole PFC converter,the switching frequency regulation range of the three-level PFC converter is reduced by 36.48%and the average switching times is reduced by 45.10%.The experimental result also shows a 1.2%higher efficiency for the three-level PFC converter in the full load range.

Multiple model particle flter track-before-detect for range ambiguous radar

The middle pulse repetition frequency（MPRF）and high pulse repetition frequency（HPRF）modes are widely adopted in airborne pulse Doppler（PD）radar systems,which results in the problem that the range measurement of targets is ambiguous.The existing data processing based range ambiguity resolving methods work well on the condition that the signal-to-noise ratio（SNR）is high enough.In this paper,a multiple model particle flter（MMPF）based track-beforedetect（TBD）method is proposed to address the problem of target detection and tracking with range ambiguous radar in low-SNR environment.By introducing a discrete variable that denotes whether a target is present or not and the discrete pulse interval number（PIN）as components of the target state vector,and modeling the incremental variable of the PIN as a three-state Markov chain,the proposed algorithm converts the problem of range ambiguity resolving into a hybrid state fltering problem.At last,the hybrid fltering problem is implemented by a MMPF-based TBD method in the Bayesian framework.Simulation results demonstrate that the proposed Bayesian approach can estimate target state as well as the PIN simultaneously,and succeeds in detecting and tracking weak targets with the range ambiguous radar.Simulation results also show that the performance of the proposed method is superior to that of the multiple hypothesis（MH）method in low-SNR environment.

Tri-frequency spectrum method and results for resolving the parameters of Earth's liquid core free nutation

The parameters of Earth free core nutation (FCN) are two relatively significant geophysical parameters. Sasao et al. (1980) and Wahr and Bergen (1986) provided the theoretical estimation values of FCN parameters. Gwinn, Herring and Shapiro (1987) first obtained the observational values of FCN parameters by very long base Interference (VLBI) at Cambridge University. In the same year, Neuberg and Zurn in former West Germany and Hinderer in France began to retrieve FCN parameters by the observation of gravity tides and introduced the stacking method. The other scholars who researched into the same geophysical problems by applying the data of gravity tides basically followed the stacking method. The results they reached were similar to the observational result of FCN parameters given by Neuberg et al. in 1987. But the observational results of FCN parameters gained from gravity tides were not identical with those from VLBI, mainly because of the large difference of quality of FCN. So there was not an affirmative observational result of FCN parameters since then. In this paper, The authors firstly introduce the tri-frequency spectrum method with clearly geometrical and geophysical meaning for the resolution of FCN parameters , and the observational results of FCN parameters obtained from tide data at three superconducting gravity stations were accordant with those from VLBI, which will be relatively important to arriving at a certain observational result of FCN parameters.

Performance analysis of source ranging by use of virtual receiver technique under different frequency bands

The traditional matched field processing localization need complicated computation to get the replica field and has high dependence on environment parameters and acoustic field model. To overcome the shortcoming, virtual receiver technique is used for source ranging. A virtual receiver is constructed by correlating the two signals of the guide source and the objective source received by a vertical line array. Then, the slope of the interference striation of the virtual field is estimated using relevant signal processing method. Combining with the waveguide invariant/3, the range of the objective source is determined. Through the numerical simulations and data processing collected from the experiment carried out in the South China Sea in 2004, the virtual receiver technique for broadband source ranging under the slope- bottom shallow water environment is discussed. As the frequency increases, the frequency bands should be broadened to obtain complete interference striation for good ranging results. In data processing, the receiving array spacing is too large to promise the orthogonality of the modes as the frequency increases and ranging results become worse.