Dry sliding friction and wear test of Nb containing low carbon microalloyed steel was carried out at room temperature,and the effect of Nb on the wear behavior of the steel,as welll as the mechanism was studied.Scanni...Dry sliding friction and wear test of Nb containing low carbon microalloyed steel was carried out at room temperature,and the effect of Nb on the wear behavior of the steel,as welll as the mechanism was studied.Scanning electron microscopy(SEM) and energy dispersive spectrometry(EDS) were employed to analyze the morphology and composition of the worn surface,and the structure evolution of the plastic deformation layer.The carbide content and type in the steel were analyzed by the electrolytic extraction device and X-ray diffraction(XRD).The experimental results demonstrate that the addition of 0.2% Nb can refine the grain and generate Nb C to improve the wear resistance of the steel.By enhancing the load and speed of wear experiment,the wear mechanism of the test steel with 0.2% Nb changes from slight oxidation wear to severe adhesion wear and oxidation wear.Compared with the load,the increase in the rotation speed exerts a greater influence on the wear of the test steel.展开更多
Fasteners of 718 alloys are used to set up connection between each support and other components for ITER system, metal-based Ag solid lubricant coating is widely used as an anti-seizure lubricant coating due to its st...Fasteners of 718 alloys are used to set up connection between each support and other components for ITER system, metal-based Ag solid lubricant coating is widely used as an anti-seizure lubricant coating due to its strong low-temperature shear resistance. But the poor adhesion to the steel surfaces has been a critical restriction for applying the silver coatings to the practical machine elements. In this work, an 8-μm silver self-lubricating coating was deposited on the surface of 718 alloy by the method of magnetron sputtering. The coating was uniform, dense and consistent. The wear mechanism was investigated by analyzing the friction and wear properties of the coating. Stress is one of the important impacts on the friction coefficient, the results showed that it first increased and then decreased with the increase of pressure at room temperature and under vacuum. Temperature exerted an effect on the silver self-lubricating coating. A study was conducted under vacuum on the friction and wear performance of the coating at 300 K, 225 K, 155 K, and 77 K, respectively. The results showed that the wear mechanism and wear state varied under various low-temperature conditions, with the severity of wear reaching the maximum only at 225 K. Through the same silver coating process, the washer of superbolt was improved by silver coating treatment.展开更多
The influence of rare earth on the friction and wear characteristics of magnesium alloy AZ91 and AM60 were studied. The results show that the wear resistance properties of rare earth magnesium alloys are better than t...The influence of rare earth on the friction and wear characteristics of magnesium alloy AZ91 and AM60 were studied. The results show that the wear resistance properties of rare earth magnesium alloys are better than those of matrix alloy under the testing conditions. The anti wear behaviour of AZ91 alloy is much better than that of AM60 alloy. In dry sliding process,magnesium alloys undergo a transition from mild wear to severe wear. The addition of rare earths refine the structure of alloys, improve the comprehensive behaviors of magnesium alloys, increase the stability of oxidation films on worn surfaces, enhance the loading ability of rare earth magnesium alloys, and delay the transition from mild wear to severe wear effectively.展开更多
The sliding friction and wear behaviors of Mg-11Y-5Gd-2Zn-0.5Zr (wt%) alloy were investigated under oil lubricant condition by pin-on-disk configuration with a constant sliding distance of 1,000 m in the temperature...The sliding friction and wear behaviors of Mg-11Y-5Gd-2Zn-0.5Zr (wt%) alloy were investigated under oil lubricant condition by pin-on-disk configuration with a constant sliding distance of 1,000 m in the temperature range of 25-200℃. Results indicate that the volumetric wear rates and average friction coefficients decrease with the increase of sliding speeds, and increase with the increase of test temperature below 150℃. The hard and thermally stable Mg12(Y,Gd)Zn phase with long-period stacking order structure in the alloy presents significant wear resistance, The wear mechanism below 100℃ is abrasive wear as a result of plastic extrusion deformation. The corporate effects of severe abrasive, oxidative, and delaminating wear result in the tribological mechanism above 100℃.展开更多
The effect of magnetic field on the tribological process of sleeve-ring pair lubricated by WRL lubricants was investigated by means of a NG-x wear tester and a PS5013 video microscope. The friction coefficient(f) and ...The effect of magnetic field on the tribological process of sleeve-ring pair lubricated by WRL lubricants was investigated by means of a NG-x wear tester and a PS5013 video microscope. The friction coefficient(f) and the wear weight(W) in lubricating test with WRL lubricant were decreased with the increase in the magnetic field vertical to the rubbing surface, and an almost zero wear lubricating situation was gained in a magnetic field of 1000A/m. The captured wear micro particles on the rubbing surface were observed in the testing process, and the theoretical analysis of magnetic effects was completed. It is indicated that the magnetic field has not only a capturing action of wear micro particles on the worn surface, but also a inducing polarization of magnetic anisotropy of lubricant molecular. The actions promote the absorption of WRL lubricant into the wear surface as well as wear micro-particles, so that a good tribological effect is obtained when both magnetic field and WRL present.展开更多
The high-temperature friction and wear properties of TiAl alloys and Ti2AlN/TiAl composites (TTC) in contact with nickel-based superalloy were studied. The results showed that, at 800 and 1 000 ℃, the coefficient o...The high-temperature friction and wear properties of TiAl alloys and Ti2AlN/TiAl composites (TTC) in contact with nickel-based superalloy were studied. The results showed that, at 800 and 1 000 ℃, the coefficient of the friction (COF) decreased with the increase of sliding velocity and the wear loss of the TTC decreased with the increase of volume fraction of Ti2AlN. The wear mechanisms of the pairs are adhesive wear and the wear debris mainly comes from the contacting nickel-based superalloy. The intergranular fracture and the cracking of the phase boundary in the lamellar structure are the wear mode of TiAl alloy. The wear mode of TTC is phase boundary fracture and adhesive spalling. The abrasive resistance of TTC is slightly higher than that of TiAl alloy.展开更多
Ni-matrix composite coating containing AI2O3 nano-particles is prepared by brush plating. The effects of the nano-particles on the microstructure, microhardness and tribological properties of the composite coating und...Ni-matrix composite coating containing AI2O3 nano-particles is prepared by brush plating. The effects of the nano-particles on the microstructure, microhardness and tribological properties of the composite coating under the lubrication of a diesel oil containing sand are investigated. The results show that the microstructure of the composite coating is finer than that of the pure nickel coating due to the codeposition of the nano-particles. When the nano-particle concentration in the electroplating bath reaches 20 g/L, the microhardness, and wear resistance of the composite coating is as much as 1.6 times and 1.3-2.5 times of those of the pure nickel coating respectively. The main hardening mechanism of the composite coating is superfine crystal grain strengthening and dispersion strengthening. The composite coating is characterized by scuffing as it slides against Si3N4 under the present test conditions.展开更多
TiC/ZA43 composites were fabricated by XD TM and stirring casting techniques. The tribology properties of the unreinforced ZA43 alloy and the composites were studied by using a block on ring apparatus. Experimental re...TiC/ZA43 composites were fabricated by XD TM and stirring casting techniques. The tribology properties of the unreinforced ZA43 alloy and the composites were studied by using a block on ring apparatus. Experimental results show that the incorporation of TiC particles improves the microstructure of ZA43 matrix alloy. The coefficient of friction μ and the width of worn groove decrease with the increase of TiC volume fraction φ (TiC). The width of worn groove and μ of the composite during wear testing increase with increasing the applied load. Metallographic examinations reveal that unreinforced ZA43 alloy has deep ploughing grooves with obvious adhesion phenomenon, whereas TiC/ZA43 composites have smooth worn surface. Delamination formation is related to the fatigue cracks and the shear cracks on the surface. [展开更多
Nano-structured layers are fabricated on the surface of 1.0C-1.5Cr steel by using the surface mechanical attrition treatment(SMAT)technology,and the microstructures of the surface nano-crystallization layers are chara...Nano-structured layers are fabricated on the surface of 1.0C-1.5Cr steel by using the surface mechanical attrition treatment(SMAT)technology,and the microstructures of the surface nano-crystallization layers are characterized by means of X-ray diffraction(XRD)and transmission electron microscopy(TEM).The friction and wear properties are also investigated by a UMT-2 friction and wear tester.Experimental research has indicated that the average diameter of nanocrystalline grains in the surface layer after being treated for 15 min is in the range of 10-20 nm,and ferrite and cementite grains can not be identified by their morphologies.The wear-resistance of the specimen treated for 15 min has been doubled,compared with that of the matrix due to the grain refinement to a nano-sized scale.The lowest friction coefficient is 0.27,which is for the specimen treated for 30 min,resulting from the dissolution of the cementite phase and the formation of a relative homogenous structure.The SMAT technique for enhancing the wear-resistance of the 1.0C-1.5Cr steel has an optimum processing time,which is in the range of 15-30 min.The dominant wear mechanism of the specimen treated for 15 min changes from adhesive wear into particle wear.展开更多
Titanium has been increasingly applied to biomedical application because of its improved mechanical characteristics, corrosion resistance and biocompatibility. However their application remains limited, due to the low...Titanium has been increasingly applied to biomedical application because of its improved mechanical characteristics, corrosion resistance and biocompatibility. However their application remains limited, due to the low strength and poor wear resistance of unalloyed titanium. The purpose of this study is to evaluate the friction and wear behavior of high-strength titanium alloys: Ti-6Al-7Nb used in femoral stem (total hip prosthesis). The oscillating friction and wear tests have been carried out in ambient air with oscillating tribotester in accord with standards ISO 7148, ASTM G99-95a, ASTM G 133-95 under different conditions of normal applied load (3, 6 and 10 N) and sliding speed (1, 15 and 25 mm.s-1), and as a counter pair we used the ball of 100C 6, 10 mm of diameter. The surface morphology of the titanium alloys has been characterized by SEM, EDAX, micro hardness, roughness analysis measurements. The behavior observed for both samples suggests that the wear and friction mechanism during the test is the same for Ti alloys, and to increase resistance to wear and friction of biomedical titanium alloys used in total hip prosthesis (femoral stems) the surface coating and treatment are required.展开更多
The friction and wear behaviors of the Cu-Cr alloy sliding against GCr15 steel at different loads and rotate speed conditions were evaluated, and the worn surface morphologies were observed on a scanning electron micr...The friction and wear behaviors of the Cu-Cr alloy sliding against GCr15 steel at different loads and rotate speed conditions were evaluated, and the worn surface morphologies were observed on a scanning electron microscope. Results show that as loads and rotate speed increase, the wear loss weight increases, by comparison, the biggest friction coefficient of Cu-Cr alloy was obtained at load 100 N and rotate speed at 100 r·min-1 friction condition. Moreover, the dominant wear forms was plough wear.展开更多
Samples of surface chromising layer were prepared by the double glow plasma discharge technique. X-ray diffraction and X-ray photoelectron spectroscopy(XPS) analysis of dif-ferent elements confirmed the formation of...Samples of surface chromising layer were prepared by the double glow plasma discharge technique. X-ray diffraction and X-ray photoelectron spectroscopy(XPS) analysis of dif-ferent elements confirmed the formation of chrome in the layer. Their tribological properties were investigated by pin-on-disk tribometer. Silicon nitride, GCr15, and nickel-based alloy were selected as counterface materials. Results indicated that the lowest friction coefficients and wear rate were ob-tained when substrate and chromising layer against nickel-based alloy, and tribological properties of chromising layer were better than those of substrate. The highest friction and wear rate were samples against silicon nitride alloys. In the case of three rubbing pairs, the unchangeable materials against different hardness counterfaces leaded to different wear mechanisms. Samples against silicon nitride exhibited abrasive mechanism, and when GCr15 and nickel-based alloy were used as counterface, transfer film and glaze layer formed on the contact surface, which played the main role in decreasing friction and wear.展开更多
A Ti-50Al alloy has been prepared by vacuum pressure casting.The full lamellar microstructure (FL) has been formed upon heat treating at 1400 ℃ and then furnace cooling.The frictional wear behavior of the alloy at th...A Ti-50Al alloy has been prepared by vacuum pressure casting.The full lamellar microstructure (FL) has been formed upon heat treating at 1400 ℃ and then furnace cooling.The frictional wear behavior of the alloy at the room temperature has been tested and its wear mechanism has been studied.The results show that with the increase of the load and sliding speed,the wear rate of the as-cast Ti-50Al alloy rises and the friction coefficient declines.When sliding speed is lower than 1.0 m/s the wear rate of the FL Ti-50Al alloy increased with the load and sliding speed,but the friction coefficient is relatively invariable at about 0.5.The wear mechanism is mainly of abrasive wear and adhesive wear.When sliding speed is higher than 1.5 m/s,the wear mechanism has changed to mainly oxidization wear so that the wear rate of the FL Ti-50Al alloy declines significantly and the friction coefficient increases.Compared to the as-cast alloy,the FL Ti-50Al alloy has better wear resistance.展开更多
The dry friction and wear properties of intermetallics MoSi 2 against 45 steel under different loads were investigated with M 2 type friction and wear tester. Scanning electric microscope (SEM) equipment with micropro...The dry friction and wear properties of intermetallics MoSi 2 against 45 steel under different loads were investigated with M 2 type friction and wear tester. Scanning electric microscope (SEM) equipment with microprobe was employed to analyze the morphology of the friction surface. Results show that the dry friction and wear properties are deeply affected by load. The wear rate of MoSi 2 at the load of 80?N is the maximum which is 36.1?μg/m. On the condition of the load of 150?N, MoSi 2 material has the better friction and wear properties: friction coefficient is 0.28 and wear rate is 10.6?μg/m. With the load increasing, the main friction mechanisms change from microslip and plastic deformation to adhesive effect, and the main wear mechanisms change from plough groove wear and oxidation fatigue wear to adhesive wear.展开更多
To solve the problem of the severe mismatch between the product and roll materials in the preliminary rolling line,a new graphitic steel material was designed,its microstructure and high-temperature friction and wear ...To solve the problem of the severe mismatch between the product and roll materials in the preliminary rolling line,a new graphitic steel material was designed,its microstructure and high-temperature friction and wear properties were investigated.Moreover,the feasibility of replacing semi-steel with this new material in the V1 stand roll was studied herein.The results show that the graphitic steel matrix is strengthened by silicon and nickel elements.The presence of spherical graphite also provides self-lubrication and heat conduction and prevents the propagation of cracks.Carbides in the appropriate amount and size strengthen the matrix,reduce the cracking effect of the matrix,and are not easily broken,thereby reducing high-temperature abrasive wear.Under the same hightemperature friction and wear conditions,compared with semi-steel,the wear-scar surface of graphitic steel exhibits less wear-scar depth and wear volume,a smaller friction coefficient,reduced oxide layer thickness,and fewer instances of peeling and microcracks.Therefore,the newly designed graphitic steel has higher wear resistance and hot-crack resistance than semi-steel,which makes it feasible for use in replacing semi-steel as a new V1 frame roll material in the blooming mill.展开更多
In this study,effects of B addition on the sintering densification,microstructure,hardness,friction and wear properties of sintered Fe-2.4C-4Cr-1Mo-0.5P-0.7Si-2.5Cu(in wt%)were investigated.In spite of the decreased s...In this study,effects of B addition on the sintering densification,microstructure,hardness,friction and wear properties of sintered Fe-2.4C-4Cr-1Mo-0.5P-0.7Si-2.5Cu(in wt%)were investigated.In spite of the decreased sintered density,the addition of B changes the phase composition of the materials and their ratio.Moreover,hardness of either the matrix or the liquid solidification structure dramatically increases.These changes in micro structure result in higher friction coefficient and lower wear loss.It is observed that the addition of0.1 wt%B offers the optimum friction and wear properties with a running-in period of only 30 s and wear volume loss of 0.006 mm^(3) under the testing conditions.Such friction and wear properties are superior to those of the other two widely used cam materials,cast iron and 45 steel.展开更多
A gradient nano-grained (GNG) surface layer was fabricated on an AIS1316L stainless steel (SS) by using the surface mechanical rolling treatment (SMRT). Reciprocating dry and oil-lubricated sliding tests of the ...A gradient nano-grained (GNG) surface layer was fabricated on an AIS1316L stainless steel (SS) by using the surface mechanical rolling treatment (SMRT). Reciprocating dry and oil-lubricated sliding tests of the GNG 316L SS in air at room temperature were conducted in comparison with the coarse-grained (CG) counterpart. Worn surface morphologies and subsurface microstructures were investigated for both 316L SS samples. 316L SS with a GNG surface layer shows a significantly improved wear resistance, especially under oil-lubricated condition. The notably wear resistance enhancement of the GNG 316L SS is attributed to the GNG surface layer with high strain accommodation ability and high hardness, which can reduce the wear volume in the running-in stage effectively.展开更多
The friction and wear behavior and mechanism as well as the mechanical properties of polytetrafluoroethylene (PTFE) composites filled with potassium titanate whiskers (PTW) and short carbon fibers (CF) under dry...The friction and wear behavior and mechanism as well as the mechanical properties of polytetrafluoroethylene (PTFE) composites filled with potassium titanate whiskers (PTW) and short carbon fibers (CF) under dry, wet and alkaline conditions were investigated. Experiments indicated that owing to appropriate cooling and boundary lubricating effects, the filled PTFE composites showed much lower frictional coefficient and better wear resistance under alkaline than dry and wet sliding conditions. The wear resistance of carbon-fiber-filled PTFE was much better than that of potassium titanate-whisker-filled PTFE composites in water. Results also showed that the transfer film on counterpart rings was significantly hindered by water and alkali. Hydrophilic-filler-reinforced PTFE composites yield higher wear rate when sliding under water.展开更多
The friction and wear behavior of resin/graphite composite has been investigated using a pin-on-disc configuration under dry sliding condition. The results showed that the resin/graphite composite exhibited much bette...The friction and wear behavior of resin/graphite composite has been investigated using a pin-on-disc configuration under dry sliding condition. The results showed that the resin/graphite composite exhibited much better mechanical and tribological properties compared with the unimpregnated graphite. The friction coefficient was reduced by addition of furan resin, which could also prevent the'dusting' wear at loads more than 15 MPa. The steady and lubricated transfer film was easily formed on the counterpart surface due to the interaction of furan resin and wear debris of graphite, which was useful to reduce the wear rate of the resin/graphite composite. The composite is highly promising for mechanical sealing application and can be used at high load for long time sliding.展开更多
In this study, AlTiN coatings were deposited on YT14 cemented carbide balls by arc ion plating technique. The friction and wear behavior of the AlTiN-coated balls against SKD11 hardened steel was investigated by slidi...In this study, AlTiN coatings were deposited on YT14 cemented carbide balls by arc ion plating technique. The friction and wear behavior of the AlTiN-coated balls against SKD11 hardened steel was investigated by sliding tests using a ball-ondisk tribometer at various temperatures from 25 to 700 ℃ in air. The results showed that the friction and wear behavior was significantly influenced by the testing temperature. Obvious fluctuations were observed in the friction curves at elevated temperatures, which could be attributed to the formation and rupture of unstable Fe and Cr oxide layers. As the temperature increased from 25 to 500 ~C, the wear rate of the coated balls increased from the scale of 10-21-10-20 m3/ N m, and then decreased to 10-22 m3/N m as the temperature further increased to 700℃. It was also found that the friction and wear behavior of the coated balls was directly dependent on the counterpart materials. As the temperature increased, the main wear mechanism of the coated balls changed from mild abrasive wear and adhesive wear to abrasive wear failure at 500℃, and then transferred to adhesive wear and mild oxidation wear at 700℃. For SKD11 hardened steel, the primary wear mechanism changed from delamination wear to abrasive wear and then transferred to plastic deformation and fatigue wear, accompanied by adhesive wear and tribo-oxidation wear.展开更多
文摘Dry sliding friction and wear test of Nb containing low carbon microalloyed steel was carried out at room temperature,and the effect of Nb on the wear behavior of the steel,as welll as the mechanism was studied.Scanning electron microscopy(SEM) and energy dispersive spectrometry(EDS) were employed to analyze the morphology and composition of the worn surface,and the structure evolution of the plastic deformation layer.The carbide content and type in the steel were analyzed by the electrolytic extraction device and X-ray diffraction(XRD).The experimental results demonstrate that the addition of 0.2% Nb can refine the grain and generate Nb C to improve the wear resistance of the steel.By enhancing the load and speed of wear experiment,the wear mechanism of the test steel with 0.2% Nb changes from slight oxidation wear to severe adhesion wear and oxidation wear.Compared with the load,the increase in the rotation speed exerts a greater influence on the wear of the test steel.
文摘Fasteners of 718 alloys are used to set up connection between each support and other components for ITER system, metal-based Ag solid lubricant coating is widely used as an anti-seizure lubricant coating due to its strong low-temperature shear resistance. But the poor adhesion to the steel surfaces has been a critical restriction for applying the silver coatings to the practical machine elements. In this work, an 8-μm silver self-lubricating coating was deposited on the surface of 718 alloy by the method of magnetron sputtering. The coating was uniform, dense and consistent. The wear mechanism was investigated by analyzing the friction and wear properties of the coating. Stress is one of the important impacts on the friction coefficient, the results showed that it first increased and then decreased with the increase of pressure at room temperature and under vacuum. Temperature exerted an effect on the silver self-lubricating coating. A study was conducted under vacuum on the friction and wear performance of the coating at 300 K, 225 K, 155 K, and 77 K, respectively. The results showed that the wear mechanism and wear state varied under various low-temperature conditions, with the severity of wear reaching the maximum only at 225 K. Through the same silver coating process, the washer of superbolt was improved by silver coating treatment.
文摘The influence of rare earth on the friction and wear characteristics of magnesium alloy AZ91 and AM60 were studied. The results show that the wear resistance properties of rare earth magnesium alloys are better than those of matrix alloy under the testing conditions. The anti wear behaviour of AZ91 alloy is much better than that of AM60 alloy. In dry sliding process,magnesium alloys undergo a transition from mild wear to severe wear. The addition of rare earths refine the structure of alloys, improve the comprehensive behaviors of magnesium alloys, increase the stability of oxidation films on worn surfaces, enhance the loading ability of rare earth magnesium alloys, and delay the transition from mild wear to severe wear effectively.
基金supported by the National Natural Science Foundation of China (No. 51074106)Key HiTech Research and Development Program of China (No. 2009AA033501)National Key Technology R&D Program of China (No. 2011BAE22B01-5)
文摘The sliding friction and wear behaviors of Mg-11Y-5Gd-2Zn-0.5Zr (wt%) alloy were investigated under oil lubricant condition by pin-on-disk configuration with a constant sliding distance of 1,000 m in the temperature range of 25-200℃. Results indicate that the volumetric wear rates and average friction coefficients decrease with the increase of sliding speeds, and increase with the increase of test temperature below 150℃. The hard and thermally stable Mg12(Y,Gd)Zn phase with long-period stacking order structure in the alloy presents significant wear resistance, The wear mechanism below 100℃ is abrasive wear as a result of plastic extrusion deformation. The corporate effects of severe abrasive, oxidative, and delaminating wear result in the tribological mechanism above 100℃.
文摘The effect of magnetic field on the tribological process of sleeve-ring pair lubricated by WRL lubricants was investigated by means of a NG-x wear tester and a PS5013 video microscope. The friction coefficient(f) and the wear weight(W) in lubricating test with WRL lubricant were decreased with the increase in the magnetic field vertical to the rubbing surface, and an almost zero wear lubricating situation was gained in a magnetic field of 1000A/m. The captured wear micro particles on the rubbing surface were observed in the testing process, and the theoretical analysis of magnetic effects was completed. It is indicated that the magnetic field has not only a capturing action of wear micro particles on the worn surface, but also a inducing polarization of magnetic anisotropy of lubricant molecular. The actions promote the absorption of WRL lubricant into the wear surface as well as wear micro-particles, so that a good tribological effect is obtained when both magnetic field and WRL present.
文摘The high-temperature friction and wear properties of TiAl alloys and Ti2AlN/TiAl composites (TTC) in contact with nickel-based superalloy were studied. The results showed that, at 800 and 1 000 ℃, the coefficient of the friction (COF) decreased with the increase of sliding velocity and the wear loss of the TTC decreased with the increase of volume fraction of Ti2AlN. The wear mechanisms of the pairs are adhesive wear and the wear debris mainly comes from the contacting nickel-based superalloy. The intergranular fracture and the cracking of the phase boundary in the lamellar structure are the wear mode of TiAl alloy. The wear mode of TTC is phase boundary fracture and adhesive spalling. The abrasive resistance of TTC is slightly higher than that of TiAl alloy.
基金This research was financially supported by the Major Project of National Natural Science Foundation of China(No.50235030)the National 973 Planning Project(No.G1999065009)+1 种基金the Science and Technology Cooperation Project between China and Poland Governments in 2002(No.2002M3)their supports are gratefully acknowledged.
文摘Ni-matrix composite coating containing AI2O3 nano-particles is prepared by brush plating. The effects of the nano-particles on the microstructure, microhardness and tribological properties of the composite coating under the lubrication of a diesel oil containing sand are investigated. The results show that the microstructure of the composite coating is finer than that of the pure nickel coating due to the codeposition of the nano-particles. When the nano-particle concentration in the electroplating bath reaches 20 g/L, the microhardness, and wear resistance of the composite coating is as much as 1.6 times and 1.3-2.5 times of those of the pure nickel coating respectively. The main hardening mechanism of the composite coating is superfine crystal grain strengthening and dispersion strengthening. The composite coating is characterized by scuffing as it slides against Si3N4 under the present test conditions.
文摘TiC/ZA43 composites were fabricated by XD TM and stirring casting techniques. The tribology properties of the unreinforced ZA43 alloy and the composites were studied by using a block on ring apparatus. Experimental results show that the incorporation of TiC particles improves the microstructure of ZA43 matrix alloy. The coefficient of friction μ and the width of worn groove decrease with the increase of TiC volume fraction φ (TiC). The width of worn groove and μ of the composite during wear testing increase with increasing the applied load. Metallographic examinations reveal that unreinforced ZA43 alloy has deep ploughing grooves with obvious adhesion phenomenon, whereas TiC/ZA43 composites have smooth worn surface. Delamination formation is related to the fatigue cracks and the shear cracks on the surface. [
基金supported by the National High-Tech.R&D Program of China(the National 863 plans projects,Grant No.2007AA03Z352)
文摘Nano-structured layers are fabricated on the surface of 1.0C-1.5Cr steel by using the surface mechanical attrition treatment(SMAT)technology,and the microstructures of the surface nano-crystallization layers are characterized by means of X-ray diffraction(XRD)and transmission electron microscopy(TEM).The friction and wear properties are also investigated by a UMT-2 friction and wear tester.Experimental research has indicated that the average diameter of nanocrystalline grains in the surface layer after being treated for 15 min is in the range of 10-20 nm,and ferrite and cementite grains can not be identified by their morphologies.The wear-resistance of the specimen treated for 15 min has been doubled,compared with that of the matrix due to the grain refinement to a nano-sized scale.The lowest friction coefficient is 0.27,which is for the specimen treated for 30 min,resulting from the dissolution of the cementite phase and the formation of a relative homogenous structure.The SMAT technique for enhancing the wear-resistance of the 1.0C-1.5Cr steel has an optimum processing time,which is in the range of 15-30 min.The dominant wear mechanism of the specimen treated for 15 min changes from adhesive wear into particle wear.
文摘Titanium has been increasingly applied to biomedical application because of its improved mechanical characteristics, corrosion resistance and biocompatibility. However their application remains limited, due to the low strength and poor wear resistance of unalloyed titanium. The purpose of this study is to evaluate the friction and wear behavior of high-strength titanium alloys: Ti-6Al-7Nb used in femoral stem (total hip prosthesis). The oscillating friction and wear tests have been carried out in ambient air with oscillating tribotester in accord with standards ISO 7148, ASTM G99-95a, ASTM G 133-95 under different conditions of normal applied load (3, 6 and 10 N) and sliding speed (1, 15 and 25 mm.s-1), and as a counter pair we used the ball of 100C 6, 10 mm of diameter. The surface morphology of the titanium alloys has been characterized by SEM, EDAX, micro hardness, roughness analysis measurements. The behavior observed for both samples suggests that the wear and friction mechanism during the test is the same for Ti alloys, and to increase resistance to wear and friction of biomedical titanium alloys used in total hip prosthesis (femoral stems) the surface coating and treatment are required.
文摘The friction and wear behaviors of the Cu-Cr alloy sliding against GCr15 steel at different loads and rotate speed conditions were evaluated, and the worn surface morphologies were observed on a scanning electron microscope. Results show that as loads and rotate speed increase, the wear loss weight increases, by comparison, the biggest friction coefficient of Cu-Cr alloy was obtained at load 100 N and rotate speed at 100 r·min-1 friction condition. Moreover, the dominant wear forms was plough wear.
基金Funded by the Natural Science Foundation of Jiangsu Province China(No.BK2005128)the Scientific Research Foundation of Nanjing University of Information and Technology
文摘Samples of surface chromising layer were prepared by the double glow plasma discharge technique. X-ray diffraction and X-ray photoelectron spectroscopy(XPS) analysis of dif-ferent elements confirmed the formation of chrome in the layer. Their tribological properties were investigated by pin-on-disk tribometer. Silicon nitride, GCr15, and nickel-based alloy were selected as counterface materials. Results indicated that the lowest friction coefficients and wear rate were ob-tained when substrate and chromising layer against nickel-based alloy, and tribological properties of chromising layer were better than those of substrate. The highest friction and wear rate were samples against silicon nitride alloys. In the case of three rubbing pairs, the unchangeable materials against different hardness counterfaces leaded to different wear mechanisms. Samples against silicon nitride exhibited abrasive mechanism, and when GCr15 and nickel-based alloy were used as counterface, transfer film and glaze layer formed on the contact surface, which played the main role in decreasing friction and wear.
文摘A Ti-50Al alloy has been prepared by vacuum pressure casting.The full lamellar microstructure (FL) has been formed upon heat treating at 1400 ℃ and then furnace cooling.The frictional wear behavior of the alloy at the room temperature has been tested and its wear mechanism has been studied.The results show that with the increase of the load and sliding speed,the wear rate of the as-cast Ti-50Al alloy rises and the friction coefficient declines.When sliding speed is lower than 1.0 m/s the wear rate of the FL Ti-50Al alloy increased with the load and sliding speed,but the friction coefficient is relatively invariable at about 0.5.The wear mechanism is mainly of abrasive wear and adhesive wear.When sliding speed is higher than 1.5 m/s,the wear mechanism has changed to mainly oxidization wear so that the wear rate of the FL Ti-50Al alloy declines significantly and the friction coefficient increases.Compared to the as-cast alloy,the FL Ti-50Al alloy has better wear resistance.
文摘The dry friction and wear properties of intermetallics MoSi 2 against 45 steel under different loads were investigated with M 2 type friction and wear tester. Scanning electric microscope (SEM) equipment with microprobe was employed to analyze the morphology of the friction surface. Results show that the dry friction and wear properties are deeply affected by load. The wear rate of MoSi 2 at the load of 80?N is the maximum which is 36.1?μg/m. On the condition of the load of 150?N, MoSi 2 material has the better friction and wear properties: friction coefficient is 0.28 and wear rate is 10.6?μg/m. With the load increasing, the main friction mechanisms change from microslip and plastic deformation to adhesive effect, and the main wear mechanisms change from plough groove wear and oxidation fatigue wear to adhesive wear.
文摘To solve the problem of the severe mismatch between the product and roll materials in the preliminary rolling line,a new graphitic steel material was designed,its microstructure and high-temperature friction and wear properties were investigated.Moreover,the feasibility of replacing semi-steel with this new material in the V1 stand roll was studied herein.The results show that the graphitic steel matrix is strengthened by silicon and nickel elements.The presence of spherical graphite also provides self-lubrication and heat conduction and prevents the propagation of cracks.Carbides in the appropriate amount and size strengthen the matrix,reduce the cracking effect of the matrix,and are not easily broken,thereby reducing high-temperature abrasive wear.Under the same hightemperature friction and wear conditions,compared with semi-steel,the wear-scar surface of graphitic steel exhibits less wear-scar depth and wear volume,a smaller friction coefficient,reduced oxide layer thickness,and fewer instances of peeling and microcracks.Therefore,the newly designed graphitic steel has higher wear resistance and hot-crack resistance than semi-steel,which makes it feasible for use in replacing semi-steel as a new V1 frame roll material in the blooming mill.
基金financially supported by the National High-tech R&D Program (No.2013AA031101)the Major Science and Technology Projects (No.2012ZX04009011)the Technology Project of Huairou District in Beijing (No.2017-8)。
文摘In this study,effects of B addition on the sintering densification,microstructure,hardness,friction and wear properties of sintered Fe-2.4C-4Cr-1Mo-0.5P-0.7Si-2.5Cu(in wt%)were investigated.In spite of the decreased sintered density,the addition of B changes the phase composition of the materials and their ratio.Moreover,hardness of either the matrix or the liquid solidification structure dramatically increases.These changes in micro structure result in higher friction coefficient and lower wear loss.It is observed that the addition of0.1 wt%B offers the optimum friction and wear properties with a running-in period of only 30 s and wear volume loss of 0.006 mm^(3) under the testing conditions.Such friction and wear properties are superior to those of the other two widely used cam materials,cast iron and 45 steel.
基金the financial supports of the National Key R&D Program of China(No.2017YFA0204401)the National Natural Science Foundation(No.51231006)the Key Research Program of Chinese Academy of Sciences(No.KGZD-EW-T06)
文摘A gradient nano-grained (GNG) surface layer was fabricated on an AIS1316L stainless steel (SS) by using the surface mechanical rolling treatment (SMRT). Reciprocating dry and oil-lubricated sliding tests of the GNG 316L SS in air at room temperature were conducted in comparison with the coarse-grained (CG) counterpart. Worn surface morphologies and subsurface microstructures were investigated for both 316L SS samples. 316L SS with a GNG surface layer shows a significantly improved wear resistance, especially under oil-lubricated condition. The notably wear resistance enhancement of the GNG 316L SS is attributed to the GNG surface layer with high strain accommodation ability and high hardness, which can reduce the wear volume in the running-in stage effectively.
基金National Natural Science Foundation of China (Nos. 20676062, 20376032) National High-Tech Research Development Program (863 Program: 2003AA333010, 2006AA03Z455) Chinese National Fundamental Research Development Program (973 Program: 2003CB615700).
文摘The friction and wear behavior and mechanism as well as the mechanical properties of polytetrafluoroethylene (PTFE) composites filled with potassium titanate whiskers (PTW) and short carbon fibers (CF) under dry, wet and alkaline conditions were investigated. Experiments indicated that owing to appropriate cooling and boundary lubricating effects, the filled PTFE composites showed much lower frictional coefficient and better wear resistance under alkaline than dry and wet sliding conditions. The wear resistance of carbon-fiber-filled PTFE was much better than that of potassium titanate-whisker-filled PTFE composites in water. Results also showed that the transfer film on counterpart rings was significantly hindered by water and alkali. Hydrophilic-filler-reinforced PTFE composites yield higher wear rate when sliding under water.
文摘The friction and wear behavior of resin/graphite composite has been investigated using a pin-on-disc configuration under dry sliding condition. The results showed that the resin/graphite composite exhibited much better mechanical and tribological properties compared with the unimpregnated graphite. The friction coefficient was reduced by addition of furan resin, which could also prevent the'dusting' wear at loads more than 15 MPa. The steady and lubricated transfer film was easily formed on the counterpart surface due to the interaction of furan resin and wear debris of graphite, which was useful to reduce the wear rate of the resin/graphite composite. The composite is highly promising for mechanical sealing application and can be used at high load for long time sliding.
基金supported in part by the projects of the National Natural Science Foundation of China(Grant No.51522502)the China Postdoctoral Science Foundation funded project(No.2016M600641)the Guangdong Natural Science Funds(Nos.2014A030311002 and 2016A050502056)
文摘In this study, AlTiN coatings were deposited on YT14 cemented carbide balls by arc ion plating technique. The friction and wear behavior of the AlTiN-coated balls against SKD11 hardened steel was investigated by sliding tests using a ball-ondisk tribometer at various temperatures from 25 to 700 ℃ in air. The results showed that the friction and wear behavior was significantly influenced by the testing temperature. Obvious fluctuations were observed in the friction curves at elevated temperatures, which could be attributed to the formation and rupture of unstable Fe and Cr oxide layers. As the temperature increased from 25 to 500 ~C, the wear rate of the coated balls increased from the scale of 10-21-10-20 m3/ N m, and then decreased to 10-22 m3/N m as the temperature further increased to 700℃. It was also found that the friction and wear behavior of the coated balls was directly dependent on the counterpart materials. As the temperature increased, the main wear mechanism of the coated balls changed from mild abrasive wear and adhesive wear to abrasive wear failure at 500℃, and then transferred to adhesive wear and mild oxidation wear at 700℃. For SKD11 hardened steel, the primary wear mechanism changed from delamination wear to abrasive wear and then transferred to plastic deformation and fatigue wear, accompanied by adhesive wear and tribo-oxidation wear.