Countries are duly focusing more on biomass resources because of the increasing oil crisis.Owing to their excellent properties,such as natural characteristics,good mechanical performance,and outstanding chemical prope...Countries are duly focusing more on biomass resources because of the increasing oil crisis.Owing to their excellent properties,such as natural characteristics,good mechanical performance,and outstanding chemical properties,cellulose-based materials are highly valued as promising bioderived nanomaterials,especially bacterial cellulose(BC).The main advantage lies in eliminating the problem of removing lignin and hemicellulose from woody cellulose.Moreover,the use of BC reduces the consumption of wood,the excessive use of which aggravates global warming.Herein,we summarize the applications of BC composites in filter,medical,and conductive materials,and other fields.This review contributes to further expand the applications of this renewable polymer.展开更多
Two kinds of Al based functionally gradient composite tubes reinforced by primary Si particles alone and primary Si/in situ Mg2Si particles jointly were successfully prepared by centrifugal casting,and their structura...Two kinds of Al based functionally gradient composite tubes reinforced by primary Si particles alone and primary Si/in situ Mg2Si particles jointly were successfully prepared by centrifugal casting,and their structural and mechanical characters were compared.It is found that the composite reinforced with primary Si particles takes a characteristic of particles distribution both in the inner and outer layers.However,composite reinforced with primary Si/Mg2Si particles jointly takes a characteristic of particles distribution only in the inner layer and shows a sudden change of particles distribution across the section of inner and outer layers.The hardness and wear resistance of Al-19Si-5Mg tube in the inner layer are greatly higher than that in the other layers of Al-19Si-5Mg tube and Al-19Si tube.Theoretical analysis reveals that the existence of Mg2Si particles is the key factor to form this sudden change of gradient distribution of two kinds of particles.Because Mg2Si particles with a lower density have a higher centripetal moving velocity than primary Si particles,in a field of centrifugal force,they would collide with primary Si particles and then impel the later to move together forward to the inner layer of the tube.展开更多
Functionally graded Al/B_4C, Al/Si C, Al/Al_2O_3 and Al/TiB_2 composites with constant 12%(mass fraction) of reinforcement were fabricated by centrifugal casting and hollow cylindrical components were obtained. Micros...Functionally graded Al/B_4C, Al/Si C, Al/Al_2O_3 and Al/TiB_2 composites with constant 12%(mass fraction) of reinforcement were fabricated by centrifugal casting and hollow cylindrical components were obtained. Microstructural characteristics were investigated at outer surface of all composites and segregation of reinforcement particles was observed. Graded property of the composites with different reinforcements was investigated through hardness and tensile measurements. Results revealed that the outer peripheries of all composites exhibit higher hardness except in Al/B_4C composite and the outer zones of all composites show higher tensile strength. Abrasive wear test was conducted on the outer peripheries of all composites and Al/TiB_2 composite exhibits less wear rate.展开更多
Al/SiC functionally graded material(FGM) was developed through a novel multi-step friction stir processing(FSP) method. Si C particles with a mean size of 27.5 μm were embedded in the groove on the 6082-Al plate. To ...Al/SiC functionally graded material(FGM) was developed through a novel multi-step friction stir processing(FSP) method. Si C particles with a mean size of 27.5 μm were embedded in the groove on the 6082-Al plate. To create a graded structure over a predefined value, FSP was carried out with three tools with different pin lengths and with varying volume fractions of SiC particles. The structure was formed by passing tools with 1-3 passes with a constant rotational and traveling speeds of 900 r/min and 20 mm/min, respectively. The experiments were conducted at room temperature. Microstructural features of functionally graded(FG) samples were examined by using scanning electron microscopy(SEM) and 3D light microscopy. Mechanical properties in terms of wear resistance and microhardness were thoroughly assessed. The results indicate that the increase in FSP pass number causes more uniform SiC particle dispersion. The microhardness values were impacted by the number of passes and improved by 51.54% for Pass 3 when compared to as-received 6082-Al. Wear resistance of Al/SiC FG samples was found to increase as a result of the addition of SiC particles.展开更多
Functional polymer composites(FPCs)have attracted increasing attention in recent decades due to their great potential in delivering a wide range of functionalities.These functionalities are largely determined by funct...Functional polymer composites(FPCs)have attracted increasing attention in recent decades due to their great potential in delivering a wide range of functionalities.These functionalities are largely determined by functional fillers and their network morphology in polymer matrix.In recent years,a large number of studies on morphology control and interfacial modification have been reported,where numerous preparation methods and exciting performance of FPCs have been reported.Despite the fact that these FPCs have many similarities because they are all consisting of functional inorganic fillers and polymer matrices,review on the overall progress of FPCs is still missing,and especially the overall processing strategy for these composites is urgently needed.Herein,a"Toolbox"for the processing of FPCs is proposed to summarize and analyze the overall processing strategies and corresponding morphology evolution for FPCs.From this perspective,the morphological control methods already utilized for various FPCs are systematically reviewed,so that guidelines or even predictions on the processing strategies of various FPCs as well as multi-functional polymer composites could be given.This review should be able to provide interesting insights for the field of FPCs and boost future intelligent design of various FPCs.展开更多
Tree species diversity is assumed to be an important component in managing forest ecosystems because of effects on multiple functions or ecosystem multifunctionality.However,the importance of tree diversity in determi...Tree species diversity is assumed to be an important component in managing forest ecosystems because of effects on multiple functions or ecosystem multifunctionality.However,the importance of tree diversity in determining multifunctionality in structurally complex subtropical forests relative to other regulators(e.g.,soil microbial diversity,stand structure,and environmental conditions)remains uncertain.In this study,effects of aboveground(species richness and functional and structural diversity)and belowground(bacterial and fungal diversity)biodiversity,functional composition(community-weighted means of species traits),stand structure(diameter at breast height and stand density),and soil factors(pH and bulk density)on multifunctionality(including biomass production,carbon stock,and nutrient cycling)were examined along a tree diversity gradient in subtropical forests.The community-weighted mean of tree maximum height was the best predictor of ecosystem multifunctionality.Functional diversity explained a higher proportion of the variation in multifunctionality than that of species richness and fungal diversity.Stand structure-played an important role in modulating the effects of tree diversity on multifunctionality.The work highlights that species composition and maximizing forest structural complexity are effective strategies to increase forest multifunctionality while also conserving biodiversity in the management of multifunctional forests under global environmental changes.展开更多
Surface functionalization of carbon nanofibers(CNFs) was carried out, i e, CNFs were firstly oxidized and then the surface was silanized by 3-Aminopropyltriethoxysilane(APTES) via an assembly method. A new kind of...Surface functionalization of carbon nanofibers(CNFs) was carried out, i e, CNFs were firstly oxidized and then the surface was silanized by 3-Aminopropyltriethoxysilane(APTES) via an assembly method. A new kind of high wear resistance s-CNFs/epoxy composite was fabricated by in-situ reaction. FTIR spectroscopy was used to detect the changes of the functional groups produced by silane on the surface of CNFs. The tribological properties and microstructures of modified and unmodified CNFs/epoxy composites were studied, respectively. The expremental results indicate that APTES is covalently linked to the surface of CNFs successfully and improves the dispersion of CNF in epoxy matrix. The friction coefficients and the wear rates of s-CNFs/epoxy composites are evidently lower than those of u-CNFs/epoxy composites under the same loads. Investigations also indicate that abrasive wear is the main wear mechanism for u-CNFs/epoxy composite, with slight adhesive wear for s-CNFs/epoxy composite under the same sliding wear condition.展开更多
The main purpose of this study was to examine the effects of plant species diversity and functional composition (the identity of the plant functional groups) on ecosystem stability of Stipa, communities in the Inner M...The main purpose of this study was to examine the effects of plant species diversity and functional composition (the identity of the plant functional groups) on ecosystem stability of Stipa, communities in the Inner Mongolia Plateau. The research work was based on a 12-year study (from 1984 to 1995) of species abundance, diversity, and primary productivity of four Stipa communities, i.e. S. baicalensis Roshev., S. grandis P. Smirn., S, krylovii Roshev., and S. klemenzii Roshev. respectively. The Shnnon-Wiener index was used as a measurement of plant diversity, while functional composition was used to differentiate the functional groups that were included in the communities. The plant species of four Stipa communities were classified into functional groups based on the differences in life forms and ecological groups, which influence their performance in resource requirements, seasonality of growth, tolerance to water stress, and life history. Plant species were classified into five functional groups based on their differences in life form, shrubs and half shrubs, perennial bunch grasses, perennial rhizome grasses, forbs, annuals and biennials. Based on their differences in water requirement these species were classified into four functional groups: xerads, intermediate xerads, intermediate mesophytes, and mesophytes. The results showed: 1) Plant species diversity stabilized ecosystem processes. Shannon-Wiener index were 2.401 4, 2.172 0, 1.624 8, 0.354 3 from S. baicalensis community to S. grandis, S. krylovii and S. klemenzii community, respectively. The dynamics of the aboveground net primary productivity (ANPP) for a 12-year's period showed a reverse pattern, the coefficients of variation of the four communities were 21.94%, 20.63%, 29.21% and 39.72% respectively. 2) The Life form functional group component of diversity was a greater determinant of the ecosystem processes than the species component of diversity. The effects of perennial bunch grasses, perennial rhizome grasses and forbs on community stability were highly significant. 3) The ecological group component of diversity was also a great determinant of the ecosystem processes. The effects of xerads, intermediate xerads, and mesophytes on community stability were also very strong.展开更多
Cylindrical components of in situ functionally gradient composite materials of Al-19Si-5Mg alloy were manufactured by centrifugal casting. Microstructure characteristics of the manufactured components were observed an...Cylindrical components of in situ functionally gradient composite materials of Al-19Si-5Mg alloy were manufactured by centrifugal casting. Microstructure characteristics of the manufactured components were observed and the effects of the used process factors on these characteristics were analyzed. The results of observations shows that, in thickness, the components possess microstructures accumulating lots of Mg2Si particles and a portion of primary silicon particles in the inner layer, a little MgzSi and primary silicon particles in the outer layer, and without any Mg2Si and primary silicon particle in the middle layer. The results of the analysis indicate that the rotation rate of centrifugal casting, mould temperature, and melt pouring temperature have evidently affected the accumulation of the second phase particles. Also, the higher the centrifugal rotation rate, mould temperature, and melt pouring temperature are, the more evident in the inner layer the degree of accumulation of Mg2Si and primary silicon particles is.展开更多
In this article, we mainly investigate the growth and existence of meromorphic solutions of a type of systems of composite functional equations, and obtain some interesting results. It extends some results concerning ...In this article, we mainly investigate the growth and existence of meromorphic solutions of a type of systems of composite functional equations, and obtain some interesting results. It extends some results concerning functional equations to the systems of functional equations.展开更多
In this study,the first-order shear deformation theory(FSDT)is used to establish a nonlinear dynamic model for a conical shell truncated by a functionally graded graphene platelet-reinforced composite(FG-GPLRC).The vi...In this study,the first-order shear deformation theory(FSDT)is used to establish a nonlinear dynamic model for a conical shell truncated by a functionally graded graphene platelet-reinforced composite(FG-GPLRC).The vibration analyses of the FG-GPLRC truncated conical shell are presented.Considering the graphene platelets(GPLs)of the FG-GPLRC truncated conical shell with three different distribution patterns,the modified Halpin-Tsai model is used to calculate the effective Young’s modulus.Hamilton’s principle,the FSDT,and the von-Karman type nonlinear geometric relationships are used to derive a system of partial differential governing equations of the FG-GPLRC truncated conical shell.The Galerkin method is used to obtain the ordinary differential equations of the truncated conical shell.Then,the analytical nonlinear frequencies of the FG-GPLRC truncated conical shell are solved by the harmonic balance method.The effects of the weight fraction and distribution pattern of the GPLs,the ratio of the length to the radius as well as the ratio of the radius to the thickness of the FG-GPLRC truncated conical shell on the nonlinear natural frequency characteristics are discussed.This study culminates in the discovery of the periodic motion and chaotic motion of the FG-GPLRC truncated conical shell.展开更多
For the first time,functionally electroless nickel plated ZrO2(NCZ)graded Ni-NCZ composite coating has been successfully co-electrodeposited from a bath with gradually increasing of stirring rate.Studies showed that c...For the first time,functionally electroless nickel plated ZrO2(NCZ)graded Ni-NCZ composite coating has been successfully co-electrodeposited from a bath with gradually increasing of stirring rate.Studies showed that co-electrodeposition in a bath with stirring rate of250r/min results in the maximum co-electrodeposited particle content and the best particle distribution.To produce NCZ graded Ni-NCZ composite coating,the stirring rate was continuously increased from0to250r/min.The electroplated coating had a continuous gradient increasing of co-electrodeposited NCZ content from substrate towards the surface.The results showed that with increasing the co-electrodeposited NCZ particles content in Ni matrix,microhardness increases from interface towards the surface of the coating.Little crystallite size of Ni matrix and higher co-electrodeposited hard particles content were recognized as the reasons of microhardness increasing.Bend test revealed that the functionally graded composite coating shows more excellent adhesion to the substrate compared with the ordinary distributed Ni-NCZ on the same substrate.This result is attributed to lower mechanical mismatch between coating and substrate in the functionally graded composite coating with respect to the uniformly distributed one.The results of wear resistance measurements reveal that wear resistance of functionally graded Ni-NCZ is higher than that of ordinary distributed composite coating.展开更多
By use of Nevanlinna value distribution theory, we will investigate the properties of meromorphic solutions of two types of systems of composite functional equations and obtain some results. One of the results we get ...By use of Nevanlinna value distribution theory, we will investigate the properties of meromorphic solutions of two types of systems of composite functional equations and obtain some results. One of the results we get is about both components of meromorphic solutions on the system of composite functional equations satisfying Riccati differential equation, the other one is property of meromorphic solutions of the other system of composite functional equations while restricting the growth.展开更多
This study presents the size-dependent nonlinear thermal postbuckling characteristics of a porous functionally graded material(PFGM) microplate with a central cutout with various shapes using isogeometric numerical te...This study presents the size-dependent nonlinear thermal postbuckling characteristics of a porous functionally graded material(PFGM) microplate with a central cutout with various shapes using isogeometric numerical technique incorporating nonuniform rational B-splines. To construct the proposed non-classical plate model, the nonlocal strain gradient continuum elasticity is adopted on the basis of a hybrid quasithree-dimensional(3D) plate theory under through-thickness deformation conditions by only four variables. By taking a refined power-law function into account in conjunction with the Touloukian scheme, the temperature-porosity-dependent material properties are extracted. With the aid of the assembled isogeometric-based finite element formulations,nonlocal strain gradient thermal postbuckling curves are acquired for various boundary conditions as well as geometrical and material parameters. It is portrayed that for both size dependency types, by going deeper in the thermal postbuckling domain, gaps among equilibrium curves associated with various small scale parameter values get lower, which indicates that the pronounce of size effects reduces by going deeper in the thermal postbuckling regime. Moreover, we observe that the central cutout effect on the temperature rise associated with the thermal postbuckling behavior in the presence of the effect of strain gradient size and absence of nonlocality is stronger compared with the case including nonlocality in absence of the strain gradient small scale effect.展开更多
This paper presents an analytical solution for the free vibration behavior of functionally graded carbon nanotube-reinforced composite(FG-CNTRC) doubly curved shallow shells with integrated piezoelectric layers. Here,...This paper presents an analytical solution for the free vibration behavior of functionally graded carbon nanotube-reinforced composite(FG-CNTRC) doubly curved shallow shells with integrated piezoelectric layers. Here, the linear distribution of electric potential across the thickness of the piezoelectric layer and five different types of carbon nanotube(CNT) distributions through the thickness direction are considered. Based on the four-variable shear deformation refined shell theory, governing equations are obtained by applying Hamilton's principle. Navier's solution for the shell panels with the simply supported boundary condition at all four edges is derived. Several numerical examples validate the accuracy of the presented solution. New parametric studies regarding the effects of different material properties, shell geometric parameters, and electrical boundary conditions on the free vibration responses of the hybrid panels are investigated and discussed in detail.展开更多
The purpose of the present study is to examine the impact of initial geometric imperfection on the nonlinear dynamical characteristics of functionally graded carbon nanotube-reinforced composite(FG-CNTRC) rectangular ...The purpose of the present study is to examine the impact of initial geometric imperfection on the nonlinear dynamical characteristics of functionally graded carbon nanotube-reinforced composite(FG-CNTRC) rectangular plates under a harmonic excitation transverse load. The considered plate is assumed to be made of matrix and single-walled carbon nanotubes(SWCNTs). The rule of mixture is employed to calculate the effective material properties of the plate. Within the framework of the parabolic shear deformation plate theory with taking the influence of transverse shear deformation and rotary inertia into account, Hamilton’s principle is utilized to derive the geometrically nonlinear mathematical formulation including the governing equations and corresponding boundary conditions of initially imperfect FG-CNTRC plates. Afterwards, with the aid of an efficient multistep numerical solution methodology, the frequency-amplitude and forcing-amplitude curves of initially imperfect FG-CNTRC rectangular plates with various edge conditions are provided, demonstrating the influence of initial imperfection,geometrical parameters, and edge conditions. It is displayed that an increase in the initial geometric imperfection intensifies the softening-type behavior of system, while no softening behavior can be found in the frequency-amplitude curve of a perfect plate.展开更多
We construct a density functional theory for two-dimensional electron (hole) gases subjected to both strong magnetic fields and external potentials. In particular, we are focused on regimes near even-denominator fil...We construct a density functional theory for two-dimensional electron (hole) gases subjected to both strong magnetic fields and external potentials. In particular, we are focused on regimes near even-denominator filling factors, in which the systems form composite fermion liquids. Our theory provides a systematic and rigorous approach to determine the properties of ground states in a fractional quantum Hall regime that is modified by artificial structures. We also propose a practical way to construct an approximated functional.展开更多
Efficient and flexible interactions require precisely converting human intentions into computer-recognizable signals,which is critical to the breakthrough development of metaverse.Interactive electronics face common d...Efficient and flexible interactions require precisely converting human intentions into computer-recognizable signals,which is critical to the breakthrough development of metaverse.Interactive electronics face common dilemmas,which realize highprecision and stable touch detection but are rigid,bulky,and thick or achieve high flexibility to wear but lose precision.Here,we construct highly bending-insensitive,unpixelated,and waterproof epidermal interfaces(BUW epidermal interfaces)and demonstrate their interactive applications of conformal human–machine integration.The BUW epidermal interface based on the addressable electrical contact structure exhibits high-precision and stable touch detection,high flexibility,rapid response time,excellent stability,and versatile“cut-and-paste”character.Regardless of whether being flat or bent,the BUW epidermal interface can be conformally attached to the human skin for real-time,comfortable,and unrestrained interactions.This research provides promising insight into the functional composite and structural design strategies for developing epidermal electronics,which offers a new technology route and may further broaden human–machine interactions toward metaverse.展开更多
The present study provides detailed experimental results on the synthesis and characterization of carbonized lithium titanate spinel(LTO) composites as electrode materials for lithium ion capacitor.The LTO particles...The present study provides detailed experimental results on the synthesis and characterization of carbonized lithium titanate spinel(LTO) composites as electrode materials for lithium ion capacitor.The LTO particles were grafted with a porous carbon layer obtained from the pyrolysis of camphor.The graphitic nature of the carbon was confirmed through Raman spectroscopy.The relative contributions from the capacitive and diffusion controlled processes underlying these electrodes were mathematically modeled.Electron transport mechanism underlying these electrodes was determined by measuring the work functions(φ) of LTO and carbon grafted LTO using ultraviolet photoelectron spectroscopy.These carbon grafted LTO composites exhibited an energy density of 330 m Wh L-1and a peak power density of 2.8 k W L-1,when employed as electrodes in coin cells with excellent cycling stability at the end of 4000 cycles.展开更多
The effect of annual additions of composted sewage sludge (CS) and thermally dried sewage sludge (TS) at 80 t ha-1 on soil chemical properties was investigated for three years in a field experiment under semiarid cond...The effect of annual additions of composted sewage sludge (CS) and thermally dried sewage sludge (TS) at 80 t ha-1 on soil chemical properties was investigated for three years in a field experiment under semiarid conditions. Humic acids (HAs) isolated by conventional procedures from CS, TS, and unamended (SO) and sludge amended soils were analysed for elemental (C, H, N, S and O) and acidic functional groups (carboxylic and phenolic) and by ultraviolet-visible, Fourier transform infrared and fluorescence spectroscopies. With respect to CS, TS had similar pH and total P and K contents, larger dry matter, total organic C, total N and C/N ratio and smaller ash content and electrical conductivity. Amendment with both CS and TS induced a number of modifications in soil properties, including an increase of pH, electrical conductivity, total organic C, total N, and available P. The CS-HA had greater O, total acidity, carboxyl, and phenolic OH group contents and smaller C and H contents than TS-HA. The CS-HA and TS-HA had larger N and S contents, smaller C, O and acidic functional group contents, and lower aromatic polycondensation and humification degrees than SO-HA. Amended soil-HAs showed C, H, N and S contents larger than SO-HA, suggesting that sludge HAs were partially incorporated into soil HAs. These effects were more evident with increasing number of sludge applications.展开更多
基金supported by grants from the National Key Research and Development Program of China(2022YFD2200804)National Natural Science Foundation of China(No.31770622).
文摘Countries are duly focusing more on biomass resources because of the increasing oil crisis.Owing to their excellent properties,such as natural characteristics,good mechanical performance,and outstanding chemical properties,cellulose-based materials are highly valued as promising bioderived nanomaterials,especially bacterial cellulose(BC).The main advantage lies in eliminating the problem of removing lignin and hemicellulose from woody cellulose.Moreover,the use of BC reduces the consumption of wood,the excessive use of which aggravates global warming.Herein,we summarize the applications of BC composites in filter,medical,and conductive materials,and other fields.This review contributes to further expand the applications of this renewable polymer.
基金Project(2008BB4177) supported by the Natural Science Foundation of Chongqing,China
文摘Two kinds of Al based functionally gradient composite tubes reinforced by primary Si particles alone and primary Si/in situ Mg2Si particles jointly were successfully prepared by centrifugal casting,and their structural and mechanical characters were compared.It is found that the composite reinforced with primary Si particles takes a characteristic of particles distribution both in the inner and outer layers.However,composite reinforced with primary Si/Mg2Si particles jointly takes a characteristic of particles distribution only in the inner layer and shows a sudden change of particles distribution across the section of inner and outer layers.The hardness and wear resistance of Al-19Si-5Mg tube in the inner layer are greatly higher than that in the other layers of Al-19Si-5Mg tube and Al-19Si tube.Theoretical analysis reveals that the existence of Mg2Si particles is the key factor to form this sudden change of gradient distribution of two kinds of particles.Because Mg2Si particles with a lower density have a higher centripetal moving velocity than primary Si particles,in a field of centrifugal force,they would collide with primary Si particles and then impel the later to move together forward to the inner layer of the tube.
基金Department of Science and Technology (India) for the financial support (Grant No.SR/S3/MERC/0116/2012)
文摘Functionally graded Al/B_4C, Al/Si C, Al/Al_2O_3 and Al/TiB_2 composites with constant 12%(mass fraction) of reinforcement were fabricated by centrifugal casting and hollow cylindrical components were obtained. Microstructural characteristics were investigated at outer surface of all composites and segregation of reinforcement particles was observed. Graded property of the composites with different reinforcements was investigated through hardness and tensile measurements. Results revealed that the outer peripheries of all composites exhibit higher hardness except in Al/B_4C composite and the outer zones of all composites show higher tensile strength. Abrasive wear test was conducted on the outer peripheries of all composites and Al/TiB_2 composite exhibits less wear rate.
文摘Al/SiC functionally graded material(FGM) was developed through a novel multi-step friction stir processing(FSP) method. Si C particles with a mean size of 27.5 μm were embedded in the groove on the 6082-Al plate. To create a graded structure over a predefined value, FSP was carried out with three tools with different pin lengths and with varying volume fractions of SiC particles. The structure was formed by passing tools with 1-3 passes with a constant rotational and traveling speeds of 900 r/min and 20 mm/min, respectively. The experiments were conducted at room temperature. Microstructural features of functionally graded(FG) samples were examined by using scanning electron microscopy(SEM) and 3D light microscopy. Mechanical properties in terms of wear resistance and microhardness were thoroughly assessed. The results indicate that the increase in FSP pass number causes more uniform SiC particle dispersion. The microhardness values were impacted by the number of passes and improved by 51.54% for Pass 3 when compared to as-received 6082-Al. Wear resistance of Al/SiC FG samples was found to increase as a result of the addition of SiC particles.
基金National Natural Science Foundation of China(51922071,51773139).
文摘Functional polymer composites(FPCs)have attracted increasing attention in recent decades due to their great potential in delivering a wide range of functionalities.These functionalities are largely determined by functional fillers and their network morphology in polymer matrix.In recent years,a large number of studies on morphology control and interfacial modification have been reported,where numerous preparation methods and exciting performance of FPCs have been reported.Despite the fact that these FPCs have many similarities because they are all consisting of functional inorganic fillers and polymer matrices,review on the overall progress of FPCs is still missing,and especially the overall processing strategy for these composites is urgently needed.Herein,a"Toolbox"for the processing of FPCs is proposed to summarize and analyze the overall processing strategies and corresponding morphology evolution for FPCs.From this perspective,the morphological control methods already utilized for various FPCs are systematically reviewed,so that guidelines or even predictions on the processing strategies of various FPCs as well as multi-functional polymer composites could be given.This review should be able to provide interesting insights for the field of FPCs and boost future intelligent design of various FPCs.
基金financially supported by the National Natural Science Foundation of China(Nos.32071561 and 31870431)the Science and Technology Innovation Program of Hunan Province(No.2021RC3104)+1 种基金the Research Foundation of the Education Bureau of Hunan Province(No.19B586)the Huitong Forest Ecological Station Funds provided by the State Forestry and Grass Administration of China(No.2021132078)。
文摘Tree species diversity is assumed to be an important component in managing forest ecosystems because of effects on multiple functions or ecosystem multifunctionality.However,the importance of tree diversity in determining multifunctionality in structurally complex subtropical forests relative to other regulators(e.g.,soil microbial diversity,stand structure,and environmental conditions)remains uncertain.In this study,effects of aboveground(species richness and functional and structural diversity)and belowground(bacterial and fungal diversity)biodiversity,functional composition(community-weighted means of species traits),stand structure(diameter at breast height and stand density),and soil factors(pH and bulk density)on multifunctionality(including biomass production,carbon stock,and nutrient cycling)were examined along a tree diversity gradient in subtropical forests.The community-weighted mean of tree maximum height was the best predictor of ecosystem multifunctionality.Functional diversity explained a higher proportion of the variation in multifunctionality than that of species richness and fungal diversity.Stand structure-played an important role in modulating the effects of tree diversity on multifunctionality.The work highlights that species composition and maximizing forest structural complexity are effective strategies to increase forest multifunctionality while also conserving biodiversity in the management of multifunctional forests under global environmental changes.
基金Funded by the National Young Top Talents Plan of China(2013042)the National Science Foundation of China(21676052,21606042)+1 种基金the Science Foundation for Distinguished Young Scholars of Heilongjiang Province(JC201403)the Natural Science Foundation of Heilongjiang Province(E2015034)
文摘Surface functionalization of carbon nanofibers(CNFs) was carried out, i e, CNFs were firstly oxidized and then the surface was silanized by 3-Aminopropyltriethoxysilane(APTES) via an assembly method. A new kind of high wear resistance s-CNFs/epoxy composite was fabricated by in-situ reaction. FTIR spectroscopy was used to detect the changes of the functional groups produced by silane on the surface of CNFs. The tribological properties and microstructures of modified and unmodified CNFs/epoxy composites were studied, respectively. The expremental results indicate that APTES is covalently linked to the surface of CNFs successfully and improves the dispersion of CNF in epoxy matrix. The friction coefficients and the wear rates of s-CNFs/epoxy composites are evidently lower than those of u-CNFs/epoxy composites under the same loads. Investigations also indicate that abrasive wear is the main wear mechanism for u-CNFs/epoxy composite, with slight adhesive wear for s-CNFs/epoxy composite under the same sliding wear condition.
文摘The main purpose of this study was to examine the effects of plant species diversity and functional composition (the identity of the plant functional groups) on ecosystem stability of Stipa, communities in the Inner Mongolia Plateau. The research work was based on a 12-year study (from 1984 to 1995) of species abundance, diversity, and primary productivity of four Stipa communities, i.e. S. baicalensis Roshev., S. grandis P. Smirn., S, krylovii Roshev., and S. klemenzii Roshev. respectively. The Shnnon-Wiener index was used as a measurement of plant diversity, while functional composition was used to differentiate the functional groups that were included in the communities. The plant species of four Stipa communities were classified into functional groups based on the differences in life forms and ecological groups, which influence their performance in resource requirements, seasonality of growth, tolerance to water stress, and life history. Plant species were classified into five functional groups based on their differences in life form, shrubs and half shrubs, perennial bunch grasses, perennial rhizome grasses, forbs, annuals and biennials. Based on their differences in water requirement these species were classified into four functional groups: xerads, intermediate xerads, intermediate mesophytes, and mesophytes. The results showed: 1) Plant species diversity stabilized ecosystem processes. Shannon-Wiener index were 2.401 4, 2.172 0, 1.624 8, 0.354 3 from S. baicalensis community to S. grandis, S. krylovii and S. klemenzii community, respectively. The dynamics of the aboveground net primary productivity (ANPP) for a 12-year's period showed a reverse pattern, the coefficients of variation of the four communities were 21.94%, 20.63%, 29.21% and 39.72% respectively. 2) The Life form functional group component of diversity was a greater determinant of the ecosystem processes than the species component of diversity. The effects of perennial bunch grasses, perennial rhizome grasses and forbs on community stability were highly significant. 3) The ecological group component of diversity was also a great determinant of the ecosystem processes. The effects of xerads, intermediate xerads, and mesophytes on community stability were also very strong.
文摘Cylindrical components of in situ functionally gradient composite materials of Al-19Si-5Mg alloy were manufactured by centrifugal casting. Microstructure characteristics of the manufactured components were observed and the effects of the used process factors on these characteristics were analyzed. The results of observations shows that, in thickness, the components possess microstructures accumulating lots of Mg2Si particles and a portion of primary silicon particles in the inner layer, a little MgzSi and primary silicon particles in the outer layer, and without any Mg2Si and primary silicon particle in the middle layer. The results of the analysis indicate that the rotation rate of centrifugal casting, mould temperature, and melt pouring temperature have evidently affected the accumulation of the second phase particles. Also, the higher the centrifugal rotation rate, mould temperature, and melt pouring temperature are, the more evident in the inner layer the degree of accumulation of Mg2Si and primary silicon particles is.
基金Project supported by NSF of China (10471065)the Natural Science Foundation of Guangdong Province (04010474)
文摘In this article, we mainly investigate the growth and existence of meromorphic solutions of a type of systems of composite functional equations, and obtain some interesting results. It extends some results concerning functional equations to the systems of functional equations.
基金Project supported by the National Natural Science Foundation of China(Nos.12002057,11872127,11832002)the Scientific Research Project of Beijing Educational Committee(No.KM202111232023)the Qin Xin Talents Cultivation Program,Beijing Information Science&Technology University(Nos.QXTCP C202102,A201901)。
文摘In this study,the first-order shear deformation theory(FSDT)is used to establish a nonlinear dynamic model for a conical shell truncated by a functionally graded graphene platelet-reinforced composite(FG-GPLRC).The vibration analyses of the FG-GPLRC truncated conical shell are presented.Considering the graphene platelets(GPLs)of the FG-GPLRC truncated conical shell with three different distribution patterns,the modified Halpin-Tsai model is used to calculate the effective Young’s modulus.Hamilton’s principle,the FSDT,and the von-Karman type nonlinear geometric relationships are used to derive a system of partial differential governing equations of the FG-GPLRC truncated conical shell.The Galerkin method is used to obtain the ordinary differential equations of the truncated conical shell.Then,the analytical nonlinear frequencies of the FG-GPLRC truncated conical shell are solved by the harmonic balance method.The effects of the weight fraction and distribution pattern of the GPLs,the ratio of the length to the radius as well as the ratio of the radius to the thickness of the FG-GPLRC truncated conical shell on the nonlinear natural frequency characteristics are discussed.This study culminates in the discovery of the periodic motion and chaotic motion of the FG-GPLRC truncated conical shell.
文摘For the first time,functionally electroless nickel plated ZrO2(NCZ)graded Ni-NCZ composite coating has been successfully co-electrodeposited from a bath with gradually increasing of stirring rate.Studies showed that co-electrodeposition in a bath with stirring rate of250r/min results in the maximum co-electrodeposited particle content and the best particle distribution.To produce NCZ graded Ni-NCZ composite coating,the stirring rate was continuously increased from0to250r/min.The electroplated coating had a continuous gradient increasing of co-electrodeposited NCZ content from substrate towards the surface.The results showed that with increasing the co-electrodeposited NCZ particles content in Ni matrix,microhardness increases from interface towards the surface of the coating.Little crystallite size of Ni matrix and higher co-electrodeposited hard particles content were recognized as the reasons of microhardness increasing.Bend test revealed that the functionally graded composite coating shows more excellent adhesion to the substrate compared with the ordinary distributed Ni-NCZ on the same substrate.This result is attributed to lower mechanical mismatch between coating and substrate in the functionally graded composite coating with respect to the uniformly distributed one.The results of wear resistance measurements reveal that wear resistance of functionally graded Ni-NCZ is higher than that of ordinary distributed composite coating.
文摘By use of Nevanlinna value distribution theory, we will investigate the properties of meromorphic solutions of two types of systems of composite functional equations and obtain some results. One of the results we get is about both components of meromorphic solutions on the system of composite functional equations satisfying Riccati differential equation, the other one is property of meromorphic solutions of the other system of composite functional equations while restricting the growth.
基金Project supported by the Natural Science Foundation of Jiangxi Science and Technology Department(No. 20202BAB204027)。
文摘This study presents the size-dependent nonlinear thermal postbuckling characteristics of a porous functionally graded material(PFGM) microplate with a central cutout with various shapes using isogeometric numerical technique incorporating nonuniform rational B-splines. To construct the proposed non-classical plate model, the nonlocal strain gradient continuum elasticity is adopted on the basis of a hybrid quasithree-dimensional(3D) plate theory under through-thickness deformation conditions by only four variables. By taking a refined power-law function into account in conjunction with the Touloukian scheme, the temperature-porosity-dependent material properties are extracted. With the aid of the assembled isogeometric-based finite element formulations,nonlocal strain gradient thermal postbuckling curves are acquired for various boundary conditions as well as geometrical and material parameters. It is portrayed that for both size dependency types, by going deeper in the thermal postbuckling domain, gaps among equilibrium curves associated with various small scale parameter values get lower, which indicates that the pronounce of size effects reduces by going deeper in the thermal postbuckling regime. Moreover, we observe that the central cutout effect on the temperature rise associated with the thermal postbuckling behavior in the presence of the effect of strain gradient size and absence of nonlocality is stronger compared with the case including nonlocality in absence of the strain gradient small scale effect.
基金Project supported by the Foundation for Science and Technology Development of National University of Civil Engineering-Ha Noi-Vietnam (No. 27-2020/KHXD-TD)。
文摘This paper presents an analytical solution for the free vibration behavior of functionally graded carbon nanotube-reinforced composite(FG-CNTRC) doubly curved shallow shells with integrated piezoelectric layers. Here, the linear distribution of electric potential across the thickness of the piezoelectric layer and five different types of carbon nanotube(CNT) distributions through the thickness direction are considered. Based on the four-variable shear deformation refined shell theory, governing equations are obtained by applying Hamilton's principle. Navier's solution for the shell panels with the simply supported boundary condition at all four edges is derived. Several numerical examples validate the accuracy of the presented solution. New parametric studies regarding the effects of different material properties, shell geometric parameters, and electrical boundary conditions on the free vibration responses of the hybrid panels are investigated and discussed in detail.
文摘The purpose of the present study is to examine the impact of initial geometric imperfection on the nonlinear dynamical characteristics of functionally graded carbon nanotube-reinforced composite(FG-CNTRC) rectangular plates under a harmonic excitation transverse load. The considered plate is assumed to be made of matrix and single-walled carbon nanotubes(SWCNTs). The rule of mixture is employed to calculate the effective material properties of the plate. Within the framework of the parabolic shear deformation plate theory with taking the influence of transverse shear deformation and rotary inertia into account, Hamilton’s principle is utilized to derive the geometrically nonlinear mathematical formulation including the governing equations and corresponding boundary conditions of initially imperfect FG-CNTRC plates. Afterwards, with the aid of an efficient multistep numerical solution methodology, the frequency-amplitude and forcing-amplitude curves of initially imperfect FG-CNTRC rectangular plates with various edge conditions are provided, demonstrating the influence of initial imperfection,geometrical parameters, and edge conditions. It is displayed that an increase in the initial geometric imperfection intensifies the softening-type behavior of system, while no softening behavior can be found in the frequency-amplitude curve of a perfect plate.
基金Supported by the National Basic Research Program of China under Grant No 2012CB921304the National Natural Science Foundation of China under Grant No 11325416
文摘We construct a density functional theory for two-dimensional electron (hole) gases subjected to both strong magnetic fields and external potentials. In particular, we are focused on regimes near even-denominator filling factors, in which the systems form composite fermion liquids. Our theory provides a systematic and rigorous approach to determine the properties of ground states in a fractional quantum Hall regime that is modified by artificial structures. We also propose a practical way to construct an approximated functional.
基金supported by National Natural Science Foundation of China(52202117,52232006,52072029,and 12102256)Collaborative Innovation Platform Project of Fu-Xia-Quan National Independent Innovation Demonstration Zone(3502ZCQXT2022005)+3 种基金Natural Science Foundation of Fujian Province of China(2022J01065)State Key Lab of Advanced Metals and Materials(2022-Z09)Fundamental Research Funds for the Central Universities(20720220075)the Ministry of Education,Singapore,under its MOE ARF Tier 2(MOE2019-T2-2-179).
文摘Efficient and flexible interactions require precisely converting human intentions into computer-recognizable signals,which is critical to the breakthrough development of metaverse.Interactive electronics face common dilemmas,which realize highprecision and stable touch detection but are rigid,bulky,and thick or achieve high flexibility to wear but lose precision.Here,we construct highly bending-insensitive,unpixelated,and waterproof epidermal interfaces(BUW epidermal interfaces)and demonstrate their interactive applications of conformal human–machine integration.The BUW epidermal interface based on the addressable electrical contact structure exhibits high-precision and stable touch detection,high flexibility,rapid response time,excellent stability,and versatile“cut-and-paste”character.Regardless of whether being flat or bent,the BUW epidermal interface can be conformally attached to the human skin for real-time,comfortable,and unrestrained interactions.This research provides promising insight into the functional composite and structural design strategies for developing epidermal electronics,which offers a new technology route and may further broaden human–machine interactions toward metaverse.
基金Indian Space Research Organization (ISRO),Government of India is gratefully acknowledged for their financial support
文摘The present study provides detailed experimental results on the synthesis and characterization of carbonized lithium titanate spinel(LTO) composites as electrode materials for lithium ion capacitor.The LTO particles were grafted with a porous carbon layer obtained from the pyrolysis of camphor.The graphitic nature of the carbon was confirmed through Raman spectroscopy.The relative contributions from the capacitive and diffusion controlled processes underlying these electrodes were mathematically modeled.Electron transport mechanism underlying these electrodes was determined by measuring the work functions(φ) of LTO and carbon grafted LTO using ultraviolet photoelectron spectroscopy.These carbon grafted LTO composites exhibited an energy density of 330 m Wh L-1and a peak power density of 2.8 k W L-1,when employed as electrodes in coin cells with excellent cycling stability at the end of 4000 cycles.
文摘The effect of annual additions of composted sewage sludge (CS) and thermally dried sewage sludge (TS) at 80 t ha-1 on soil chemical properties was investigated for three years in a field experiment under semiarid conditions. Humic acids (HAs) isolated by conventional procedures from CS, TS, and unamended (SO) and sludge amended soils were analysed for elemental (C, H, N, S and O) and acidic functional groups (carboxylic and phenolic) and by ultraviolet-visible, Fourier transform infrared and fluorescence spectroscopies. With respect to CS, TS had similar pH and total P and K contents, larger dry matter, total organic C, total N and C/N ratio and smaller ash content and electrical conductivity. Amendment with both CS and TS induced a number of modifications in soil properties, including an increase of pH, electrical conductivity, total organic C, total N, and available P. The CS-HA had greater O, total acidity, carboxyl, and phenolic OH group contents and smaller C and H contents than TS-HA. The CS-HA and TS-HA had larger N and S contents, smaller C, O and acidic functional group contents, and lower aromatic polycondensation and humification degrees than SO-HA. Amended soil-HAs showed C, H, N and S contents larger than SO-HA, suggesting that sludge HAs were partially incorporated into soil HAs. These effects were more evident with increasing number of sludge applications.